Altronix ALTV1224C Quick start manual

ALTV1224C

AC/DC Dual Output Power Supply

Overview:

The Altronix ALTV1224C AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC outputs where a combination of both AC and DC outputs are required. It will provide eight (8) 3.5 amps 12VDC outputs and eight (8) 3.5 amps 24 VAC outputs.

Specifications:

• 115 VAC 50 / 60 HZ, 1.45 amps.

• 7 amps total continuous output current.

• 3.5 amps continuous supply current at

24VAC output.

• 3.5 amps continuous supply current at 12VDC.

• 16 individually fused outputs.

(8 outputs @ 12VDC and 8 outputs@ 24VAC)

(Fig. 1).

• Main fuses are rated at 5 amps / 250VAC

(Fig. 1).

• AC /DC power LED indicator.

• Surge protection.

• Spare fuses included.

• Unit maintains camera synchronization.

• Power ON/OFF switch.

• Ease of installation saves time and eliminates costly labor.

Enclosure dimensions: 15.5"H x 12"W x 4.5"D

+ DC INPUT -

SMP5PM

SUPERVISED POWER SUPPLY / CHARGER

F1 F2 F3 F4 F5 F6 F7 F8

P

FUSED POWER OUTPUTS

1 2 3 4 5 6 7 8

N

COMMON POWER OUTPUTS

PD8

SPARE

MOV

LED

SW1

ON OFF

DC Outputs

DC

AC

XFMR

F1 F2 F3 F4 F5 F6 F7 F8

P

FUSED POWER OUTPUTS

1 2 3 4 5 6 7 8

N

COMMON POWER OUTPUTS

PD8

SPARE

MOV

LED

SW1

ON OFF

AC Outputs

Fig. 1

Black

Lead

White

Lead

120 VAC,

60 Hz Input,

1.45 A

Optional available with 220VAC input order model # ALTV1224C/220.

Installation Instructions:

1.

Mount ALTV1224C enclosure in desired location.

2.

Slide switch SW1 (Fig. 1) to OFF position.

3.

Connect the AC (115 VAC 50 / 60 Hz) to the two black and white flying leads of the transformers (Fig 1).

4.

Connect devices to output terminals using the following procedure (Fig. 1).

Connect each DC device to terminal pairs on DC output board 1 thru 8, marked [P (+) and N (-)] carefully observing correct polarity.

Connect each AC device to terminal pairs on AC output board 1 thru 8, marked [P (+) and N (-)].

Note: Is good operating practice to measure output voltage before connecting devices.

5.

When batteries are being used the DC output voltage must be adjusted by turning the trim pot VR1 (Fig 1) clockwise to increase the output voltage to 13.7 VDC. Connect battery to terminals marked [- BAT +] (Fig. 1) on the unit (battery leads included).

CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the output voltage. When the battery charging voltage is increased the DC output voltage will also increase.

6.

Slide switch SW1 (Fig. 1) to ON position.

7.

Green LED on the PD8’s will illuminate when power is present.

8.

Upon completion of wiring, secure enclosure door with screws (supplied).

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes and in accordance with the national electrical code.

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

Terminal Identification:

SMP5

Terminal Legend Function/Description

AC/ AC Low voltage AC input (24VAC / 175VA).

Altronix part # T24175

+ DC -

- BAT +

PD8 (DC output)

1P - 8P

1N - 8N

12VDC 3.5 amps total continuous output.

Stand-by battery connections. Maximum charge rate .5 amp.

Positive DC power outputs.

Negative DC power outputs.

PD8 (AC output)

1P - 8P

1N - 8N

Enclosure dimensions:

15.5"H x 12"W x 4.5"D

AC power outputs.

AC power outputs.

2.25" 3.68"

12"

4.56"

1.22"

2"

1.22"

4.5"

1"

.875" 9.97" 1.3"

1"

1.22"

2"

8"

13.25"

13.53"

3.25"

2.2"

1.25"

15.5"

1.22"

2.25" 3.68"

MEMBER

Altronix Corp.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.

IIALTV1224C-Rev. 061699

4.56"

1"