Honeywell HCM-750 Important Safety Instructions Manual

Add to My manuals
27 Pages

advertisement

Honeywell HCM-750 Important Safety Instructions Manual | Manualzz

HONEYWELL

EASY TO CARE TOP FILL

EVAPORATIVE HUMIDIFIER

MODEL HCM-750 Series

IMPORTANT SAFETY

INSTRUCTIONS

READ AND SAVE THESE SAFETY

INSTRUCTIONS BEFORE USING

THIS HUMIDIFIER

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following

1. Always place this humidifier on a firm, flat and level surface. This humidifier may not work properly on an uneven surface.

2. Place this humidifier in an area where it is not accessible to children.

3. Do not place the humidifier near any heat sources such as stoves, radiators, and heaters.

4. Do not use the humidifier outdoors.

5. Before using the humidifier, check the power cord for any signs of damage. If the cord is found to be damaged,

DO NOT USE and return the humidifier to the manufacturer under the warranty agreement for repair.

6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit securely in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

DO NOT attempt to defeat this safety feature.

7. To disconnect the humidifier, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. Never pull by the cord.

8. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

9. The humidifier should always be unplugged and emptied when not in operation or while being serviced or cleaned.

10. Never tilt or attempt to move the humidifier while it is operating or filled with water.

UNPLUG the humidifier before moving.

11. This humidifier requires regular cleaning. Refer to the CLEANING instructions provided. Never clean the humidifier in any manner other than as instructed in this manual.

12. Do not direct moisture flow directly at individuals, walls or furniture.

13. When a humidifier is used in a closed room or small rooms, check periodically for proper ventilation, as excessive humidity can cause condensation stains on walls.

14. Turn the humidifier OFF if you notice moisture on the inside of your windows. For proper humidity reading use a hygrometer, which is available in many hardware and department stores, or by ordering one from the manufacturer.

15. This product is intended for residential use only.

The Honeywell trademark is used by Kaz, Inc. under license from Honeywell International Inc.

Honeywell International Inc. makes no representation or warranties with respect to this product.

INTRODUCTION

How it Works:

The Easy to Care Evaporative Humidifier is designed to quietly provide invisible cool moisture.

Water is pumped from the water reservoir through the water flow channel. Water is dispersed from water flow channel into the wicking filter which helps remove minerals and impurities from the water. A fan quietly pushes moisture out of the wick and into the air in the form of an ultra fine invisible mist.

The unique top fill design makes filling as easy as watering a plant. This unit is also equipped with a water circulating feature which helps indicate when refilling is needed.

Your humidifier is made up of these parts:

Clear Protective Cover

Top Grille

Water Outlet

Water Hose

Wicking Filter

Pump Outlet

Water Pump

Wicking Filter Tray

Main Housing Water Fill Baffle l

Fill Funnel

2

Main Housing

On/Off Switch

Moisture Output Switch

Water Window

SETTING UP YOUR HUMIDIFIER

Remove from box

Remove packaging material. Remove and set aside instruction manual. Recycle box and packaging materials or save box for end of season storage.

To prevent water pump from shifting during transportation

it has been taped to the inside of your humidifier. Remove grille and filter tray and locate the water pump on the bottom of the main housing. Remove shipping tape located on water pump and place water pump back in slot.

Replace filter tray and grille on top of main housing.

Make sure it is securely in place and hose is not bent or crimped or unit will not operate.

Figure 1

Figure 2

Placement

Select a firm, level location at least 6" (15cm) from any walls for proper airflow. Place the humidifier on a waterresistant surface, as water can damage furniture and some flooring.

Kaz will not accept responsibility for property damage caused by water spillage.

Filling

Fill pitcher or jug with up to

1.5 gallon of cool water.

Note: You can fill this humidifier with as much as 1.5 gallon of water or as little as a cup of water.

Pour water into the fill funnel area located on the top of the unit.

Indications that your humidifier needs to be refilled are:

- Water will stop circulating through the water channel.

- Your humidifier will start to sound louder.

- Water level is not visible in water window or below the refill line

3

4

OPERATING: HCM-750 Series

On/Off Power Output Controls

With the power switch in the

OFF position, plug the filled humidifier into a polarized 120V outlet. DO NOT FORCE THE

POLARIZED PLUG INTO THE

OUTLET; It will only fit one way.

DO NOT plug in humidifier with wet hands to avoid electric shock.

Turn the power knob to the

On position.

NOTE: DO NOT OPERATE WITH TOP COVER REMOVED.

Doing so could result in water spilling from humidifier.

Set your output control to:

High: Maximum Moisture for Larger Rooms

Medium: Moisture

Maintenance

Low:

Sound Sleep or

Small Rooms

REPLACING YOUR WICKING FILTER

It is recommended that you change your wicking filter every 1-2 months depending on water quality and usage.

To extend filter life remove filter from unit when not in use and allow to dry in a well ventilated area.

NOTE: Wicking Filter performance will diminish depending on the mineral content of the water and the amount of airborne dust in the environment.

IMPORTANT: CHECK WICKING FILTER REGULARLY.

Any of the following conditions indicate that it is time to replace the Wicking Filter.

• A buildup of impurities and minerals on the Wicking Filter (evidenced by discoloration of the Wicking Filter)

• An appreciable decrease in Humidifier output. Please keep in mind if your relative humidity is high your humidifier will put out less moisture.

• The top surface of the Wicking Filter is not moist to the touch

• The Wicking Filter has large holes or tears

The Wicking Filter should be replaced at least one or two times during the season, depending on usage, mineral content of the water and the environment. We encourage you to only use a

Honeywell HAC-700 Replacement

Wicking Filter. The use of other Wicking Filters may lead to sub-standard performance.

REPLACING YOUR WICKING FILTER (Continued)

STEP 1 STEP 2 STEP 3

STEP 4

Replacement

Wicking Filter HAC-700 or Filter B.

With dry hands unplug humidifier and carry to kitchen or bathroom.

Remove top grille and set aside.

STEP 5 STEP 6 STEP 7

Remove the wicking filters from the filter tray.

Discard the old wicking filters.

STEP 8

Soak new filters in cool water.

DO NOT wring filters.

Place new filters in the filter tray.

Replace top grille.

CLEANING: HCM-750 Series

NOTE: It is recommended that all maintenance be done in the kitchen or bathroom on a water resistant surface.

Weekly Cleaning: To properly clean your humidifier we recommend the process of scale removal and disinfecting.

Dishwasher Safe:

The following parts are

TOP RACK dishwasher safe for residential dishwashers operating at temperatures below 70°C/158°F.

It is recommended that you run the dishwasher on the light duty or normal cycle. Do not wash humidifier parts with soiled articles/dishes.

DO NOT USE DETERGENTS. If you use your dishwasher to clean the following parts you will

not need to follow the disinfecting and scaling procedure.

Please Note: Do not place parts on lower rack of dishwasher. Using the lower rack could cause damage to the humidifier

parts and dishwasher.

Fill

Funnel

Protective

Clear Cover

Top Grille

Wicking Filter

Tray

Water Hose Pump

Water Fill Baffle

5

CLEANING: HCM-750 Series (continued)

The main housing and wicking filters are

NOT DISHWASHER SAFE.

Placing these parts in the dishwasher will damage your humidifier and render it unable to operate properly.

Main Housing

Wicking Filters

Scale Removal directions:

STEP 1

STEP 2 STEP 3

Remove top grille, filters, filter tray, water pump, water hose, fill baffle, clear protective cover and water fill funnel and set aside.

Set Wicking Filters aside.

Note: Wicking filters cannot be de-scaled or disinfected. Doing so will damage filters and unit will not operate properly.

Empty water from the humidifier by pouring out in the direction of the control panel.

Follow the indicator arrows located inside the main housing.

Fill water reservoir of main housing with 2 cups vinegar.

STEP 4

STEP 5

STEP 6

With your unit un-assembled, proceed to the disinfecting instructions.

6

Place water pump, water hose, water fill baffle, protective clear cover and fill funnel inside main housing to soak in vinegar.

Gently wipe grille and filter tray with undiluted vinegar if you choose not to use the dishwasher option.

Soak for 20 minutes.

Rinse main housing and parts not put in dishwasher until vinegar smell is gone.

CLEANING: HCM-750 Series (continued)

Disinfecting directions: Disinfect following scale removal

STEP 1

STEP 2

STEP 3

1 gal

NOTE: USING MORE

THAN 1 TB OF BLEACH

PER GALLON OF

WATER WILL RESULT

IN DAMAGE TO YOUR

HUMIDIFIER.

DO NOT DISINFECT the

Wicking Filters.

Set aside top grille, protective clear cover, filter tray, water pump, water hose, water fill baffle and fill funnel.

Add 1 TB of bleach to 1 gallon water. Add 1 gallon of water/bleach solution to water reservoir of the main housing. Using this mixture wipe the walls of the main housing.

STEP 4 STEP 5

Soak water hose, water pump, water fill baffle, fill funnel and protective clear cover in water reservoir of the main housing if these parts were not cleaned on the top rack of dishwasher.

Soak for 15-20 minutes.

Wipe top grille and filter tray with the water - bleach solution if these parts were not placed in dishwasher.

Thoroughly rinse main housing and any parts not placed in dishwasher until the smell of bleach is gone.

Note: Please be careful of clothing, rugs and other non bleach resistant materials when disinfecting. Spilling bleach on clothing, rugs and certain surfaces may cause damage.

7

RE-ASSEMBLING: HCM-750 Series

STEP 1

STEP 2 STEP 3

STEP 4

Insert pump outlet into hose opening and gently press into place until water pump outlet will not sit any further inside water tube.

Insert water pump/hose assembly into slot in main housing.

Note: The pump will only fit one way.

Affix water hose to main housing by gently inserting water hose onto the water outlet.

Line up the fill funnel with the slots behind the water window.

Gently insert into place.

STEP 5

STEP 6 STEP 7

8

Re-insert the water fill baffle into the water reservoir of the main housing by lining up with the guides and gently pushing down to insert.

Place filter tray onto main housing. Then replace the filters back onto the filter tray.

Replace the top grille and protective clear cover.

END-OF-SEASON CARE AND STORAGE

Follow the CLEANING instructions when the humidifier will not be used for at least one week or more, or at the end of the season.

NOTE: Discard old filters and start with new filters next season.

Dry the humidifier completely before storing.

DO NOT store with water inside the main housing water reservoir or water tube.

Pack unit in original carton and store in a cool, dry location.

CONSUMER RELATIONS

Mail questions or comments to:

Kaz, Inc.

Consumer Relations Dept.

250 Turnpike Road, Southborough, MA

01772

Please be sure to specify model number.

Call us toll-free at:

1-800-477-0457

E-mail:

[email protected]

Or visit our website at:

www.kaz.com

TO ORDER REPLACEMENT PARTS

HAC-700 Replacement Wicking Filter

HCM-750 Grille (Top Grille)

HCM-750 Filter Tray (Wicking Filter Tray)

HCM-750 Cover (Clear Protective Cover)

HCM-750 Level (Fill Funnel)

HCM-750 Fill Wall (Water Fill Baffle)

750/200 Pump (Water Pump)

HCM-750 Hose (Water Hose)

PC-2 Protec

Antimicrobial Cleaning

Cartridge

ELECTRICAL RATINGS

The Honeywell HCM-750 Series models are rated at 120V, 60 Hz.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST

OR SEE YOUR WARRANTY. DO NOT RETURN THE HUMIDIFIER TO THE ORIGINAL PLACE OF

PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING OR TAMPER WITH INTER-

LOCK SWITCH YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE

TO THE PRODUCT OR PERSONAL INJURY.

FREQUENTLY ASKED QUESTIONS

Cleaning

Question

How do I clean inside the water pump?

Answer

You can clean the inside of the pump by turning the cover counter-clockwise. Remove the cover and you can clean the housing and disk.

What parts are dishwasher safe?

The water hose, water pump, protective clear cover, top grille, filter tray, water fill baffle and water funnel.

How do I assemble my humidifier after cleaning? See page 8 of your owners manual.

Can I use dish soap to clean my humidifier?

It is not recommended that you use dish soap to clean your humidifier as it is very hard to remove all the soap and this could cause damage to your humidifier. It is important that if you are using your dishwasher to clean these parts that detergent is NOT used.

9

10

FREQUENTLY ASKED QUESTIONS (Continued)

Cleaning (Continued)

Question Answer

Can I add water treatments to this humidifier?

You should only add water treatments to your humidifier that are specifically made for evaporative humidifiers such as the Protec

TM

Antimicrobial Cleaning Cartridge, model PC-1 or PC-2.

Using water treatments that are not recommended for evaporative humidifiers could damage your humidifier. If you are concerned about hard water it is recommended you use distilled water in your humidifier.

Operation

Question

What setting should I put my humidifier on?

I ran my humidifier overnight in a very dry room and the humidity barely changed but my water level decreased quite a bit.

Answer

You should run your humidifier on the highest setting if your room is very dry. Once you are at a more comfortable humidity you can turn your output setting to a lower setting.

It may take a few days for your humidity to increase.

Wood, rugs and other objects in your room will absorb moisture before before you can feel the effects if it is extremely dry.

Can I run my humidifier without filters?

No, your humidifier will not operate properly without filters. The filters absorb the moisture distributed by the water flow channel. A quiet fan then blows through the filters distributing moisture into the air.

How often should I change my wicking filters?

In general the wicking filters will last 1-2 month depending on water quality and usage. See Filter

Replacement section for information on how to determine when it is time to change the filters.

How do I know my humidifier is operating properly

I cannot see any mist coming out of my humidifier.

You will see water flowing through the water flow channel on the top of the humidifier. You will also notice a decrease in the water level after 8 hrs of use.

Your humidifier uses the process of evaporative.

This produces an ultra fine invisible moisture. You will see your water level decrease and this is an indication your humidifier is operating properly.

See Troubleshooting Guide for more.

FREQUENTLY ASKED QUESTIONS (Continued)

Operation (Continued)

Question

There is no water running through the water flow area on the top housing.

Why did my humidifier suddenly start sounding loud?

How much water does my humidifier hold?

Answer

First check to make sure there is water in your humidifier. If yes, check your water pump to make sure it is properly seated in the holding area. Next check to make sure the water hose is firmly attached to both the water pump and the water outlet.

Last, make sure there is nothing obstructing the water flow area on the top grille or water hose.

If these steps do not help, please see our

Troubleshooting Guide or contact our customer service department at 1-800-477-0457.

Check your water level. If your humidifier starts sounding louder it is an indication that you need to refill your humidifier.

Your humidifier can hold up to 1.5 Gallons of water.

How long will my humidifier run when full?

Your humidifier will run up to 17 hrs on high and

48 hrs on low.

11

12

TROUBLESHOOTING

1. Water is not flowing

a

. Check to be sure there is water in the tank and it is covering the pump b. Check water hose to be sure there are no kinks. Water hose should be pushed fully onto both the water outlet and pump c. Make sure pump is fully seated in slot at bottom of main housing d. Turn unit off, then back on to help clear any air in the system e. If water still is not flowing, remove pump, disassemble and make sure pump impeller can spin freely and there is nothing blocking pump inlet or other water passages f. Make sure the grille is fully seated and can accept water from the supply funnel

2. Unit flows water but does not produce mist

a. This unit does not produce visible mist

3. Unit flows water but filter is not moist

a. Check to be sure the holes in the water feature are not blocked and can drip water onto the filters

4. Pump makes a swishing sound

a. The pump may have sucked in air. Be sure there is enough water in the tank to cover the pump.

b. After filling, turn the unit off for a few seconds, then turn it back on to clear the system of air.

5. Pump makes a whirring sound

a. The pump may not be properly seated. Be sure to push pump fully into slot in main housing. After seating the pump properly, turn the unit off for a few seconds, then turn it back on. This will allow the pump to synchronize with the drive magnet.

6. Unit has poor output

a. Make sure the filters are moist and you can feel airflow coming through the filters. b. Make sure the water fill baffle and grille are properly seated.

c. If both a and b are OK, the relative humidity in your home could be high. The unit will automatically regulate the output based on the amount of humidity already in the air.

7. Unit makes dripping or trickling sound

a. Make sure the fill funnel is properly assembled and mounted in the tank behind the water window. b. Make sure the grille is properly seated and the fill funnel can accept water.

c. Make sure the mesh supporting the filter is not damaged.

3 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

A. This 3 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. It also does not apply to the filter or Protec

Antimicrobial

Cartridge. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

KAZ IS NOT LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES OF ANY

NATURE. ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ON THIS PRODUCT

IS LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction.

This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Kaz will repair or replace this product if it is found to be defective in material or workmanship.

C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

D. Return defective product to Kaz,

Incorporated with a brief description of the problem. Include proof of purchase and a

$10 US/$15.50 CAN check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number.

You must prepay shipping charges.

We suggest having tracking or delivery confirmation. Send to:

In U.S.A.:

Kaz, Incorporated

Attn: Returns Department

4755 Southpoint Drive

Memphis, TN 38118

USA

In Canada:

Kaz Canada, Inc.

Attn: Returns Department

510 Bronte Street South

Milton, ON L9T 2X6

Canada

Please go to www.kaz.com and register your product under the Customer Care Center and receive product information updates and new promotional offers.

©2010 Kaz, Incorporated. All Rights Reserved.

P/N: 31IMM750190

13

HONEYWELL HUMIDIFICADOR

EVAPORATIVO DE FÁCIL

CUIDADO, LLENADO POR

ARRIBA

MODELO de la Serie HCM-750

INSTRUCCIONES

IMPORTANTES DE

SEGURIDAD

LEA Y GUARDE ESTAS INSTRUC-

CIONES DE SEGURIDAD ANTES DE

USAR ESTE HUMIDIFICADOR

Siempre se deben tomar las precauciones básicas cuando se usen artefactos eléctricos para reducir el riesgo de incendio, choque eléctrico y lesiones personales, incluyendo lo siguiente:

1. Siempre coloque este humidificador sobre una superficie firme, plana y nivelada.

Es posible que este humidificador no funcione debidamente sobre una superficie desnivelada.

2. Coloque este humidificador en un lugar fuera del alcance de los niños.

3. No coloque el humidificador cerca de ninguna fuente térmica como estufas, radiadores y calentadores.

4. No use el humidificador al aire libre.

5. Antes de usar el humidificador, verifique que el cordón eléctrico no tenga señales de avería. Si considera que el cordón está estropeado,

NO LO USE y devuelva el humidificador al fabricante conforme al acuerdo de garantía para su reparación.

6. Este artefacto tiene un enchufe polarizado (una punta es más ancha que la otra). Para reducir el riesgo de choque, este enchufe ha sido diseñado para que encaje de una forma solamente en un tomacorriente polarizado. Si el enchufe no encaja completamente en el tomacorriente, inviértalo. Si aún no encaja, comuníquese con un electricista competente. NO trate de ir en contra de esta

Kaz Inc utiliza la marca de comercio Honeywell con autorización de Honeywell International Inc.

Honeywell International Inc. no hace ninguna declaración o garantía con respecto a este producto.

característica de seguridad.

7. Para desconectar el humidificador, primero coloque los controles en la posición apagada

(OFF), luego sujete el enchufe y sáquelo del tomacorriente. Nunca tire del cordón.

8. Una conexión floja entre la toma de corriente alterna (tomacorriente o receptáculo) y el enchufe puede hacer que el enchufe se recaliente y se deforme. Comuníquese con un electricista competente para cambiar un tomacorriente flojo o gastado.

9. Se debe desenchufar y vaciar el humidificador siempre que no esté funcionando o durante su reparación o limpieza.

10. Nunca incline ni trate de mover el humidificador mientras esté funcionando o esté lleno de agua.

DESENCHÚFELO antes de moverlo.

11. El humidificador se debe limpiar con regularidad.

Consulte las instrucciones de LIMPIEZA provistas. Nunca limpie el humidificador de ninguna otra manera que no sea conforme con las instrucciones de este manual.

12. Nunca oriente el vapor directamente hacia personas, paredes o muebles.

13. Si usa el humidificador en una habitación cerrada o en una habitación pequeña, debe comprobar periódicamente que haya la adecuada aireación ya que un nivel de humedad demasiado elevado provocará manchas de condensación en las paredes.

14. Apague el humidificador si se forma condensación en el interior de las ventanas.

Para obtener el nivel de humedad exacto, use un higrómetro que puede conseguir en una ferretería o en un gran almacén. También puede hacer un pedido al fabricante.

15. Este producto está fabricado solo para uso residencial.

27

INTRODUCCIÓN

Cómo Funciona:

El humidificador Ultrasónico de Cuidado Fácil está diseñado para proveer silenciosamente vapor frío invisible. El agua se bombea desde el depósito de agua a través del canal de flujo de agua.

El agua es dispersada del canal de flujo de agua al filtro filamentoso, el cual ayuda a capturar los minerales y las impurezas del agua. Un ventilador silencioso empuja el vapor fuera del filtro al aire en forma de un vapor invisible ultra fino.

El diseño único de llenado por arriba hace que sea tan fácil como vertir agua a una planta.

Esta unidad está equipada con una característica de circulación de agua la cual ayuda a indicar cuando se necesita rellenar.

Su humidificador consta de las siguientes partes:

Cubierta Transparente

Protectora

Rejilla Superior

Salida del agua

Manguera del agua

Filtro Filamentoso

Salida de la Bomba

Bomba de agua

Bandeja del Filtro

Filamentoso

Cubierta Principal del Deflector de Llenado de Agua

Embudo de

Llenado

Cubierta Principal

Interruptor Encendido/Apagado

28

Interruptor de Salida de Humedad

Ventana del Agua

INSTALAR SU HUMIDIFICADOR

Saque de la caja

Retire el material de empaque. Retire y coloque a un lado el manual de instrucciones. Recicle la caja y el material de empaque o guarde la caja para almacenar al final de la temporada.

Para prevenir que la bomba de agua se mueva al transpor-

tarla se ha pegado al interior de su humidificador. Retire la rejilla y la bandeja del filtro y localice la bomba de agua en el fondo de la cubierta principal. Retire la cinta para transporte de la bomba de agua y ponga la bomba de agua en la ranura.

Vuelva a colocar la bandeja del filtro y la rejilla en la parte superior de la cubierta principal.

Asegúrese que esté segura en su lugar y que la manguera no esté doblada o presionada o la unidad no funcionará.

Figura 1

Figura 2

Colocación

Seleccione una ubicación firme y nivelada retirada por lo menos 15 cm (6”) de cualquier pared para un flujo de aire apropiado. Coloque el humidificador en una superficie resistente al agua, ya que el agua puede dañar algunos muebles o pisos.

Kaz no aceptará responsabilidad alguna por daños causados por derramamiento de agua.

Llenado

Llene una jarra con hasta

1.5 galones de agua fría.

Nota: Usted puede llenar este humidificador con hasta 1.5 galones de agua

ó con tan sólo una taza de agua.

Vierta el agua en el área del embudo de llenado localizado en la parte superior de la unidad.

Indicaciones de que su humidificador necesita ser rellenado:

- El agua deja de circular a través del canal de agua.

- Su humidificador hace un ruido más fuerte.

- El nivel del agua no es visible en la ventana del agua o debajo de la línea de rellenado.

29

OPERACIÓN: Series HCM-750

Encendido/Apagado Potencia Controles de Salida

30

Con el interruptor de Encendido en posición de APAGADO, conecte el humidificador lleno a un tomacoriente polarizado de 120V~. NO

FORCE EL ENCHUFE POLAR-

IZADO EN EL TOMACORRIENTE; es unidireccional.

NO conecte el humidificador con las manos mojadas para evitar descarga eléctrica.

Gire la perilla de la potencia a la posición de ENCENDIDO.

Ajuste su control de salida en:

Alto: Humedad Máxima para Habitaciones más Grandes

Medio: Conservación de la

Humedad

Bajo: Sueño Profundo o Habitaciones

Pequeñas

NOTA: NO OPERE SIN LA CUBIERTA SUPERIOR.

El hacerlo podría resultar en derramamiento de agua del humidificador.

REEMPLAZAR SU FILTRO FILAMENTOSO

Es recomendable cambiar su filtro filamentoso cada 1-2 meses dependiendo de la calidad del agua y el uso.

Para aumentar la vida útil del filtro retire el filtro de la unidad cuando no esté en uso y permita que seque en un

área ventilada.

NOTA: El desempeño del Filtro Filamentoso disminuirá dependiendo del contenido mineral del agua y de la cantidad de polvo aerotransportado en el medio ambiente.

IMPORTANTE: REVISE REGULARMENTE EL FILTRO FILAMENTOSO.

Cualquiera de las siguientes condiciones indican que es momento de cambiar su Filtro Filamentoso.

• Acumulación de impurezas y minerales en el Filtro Filamentoso (evidenciado por la decoloración del Filtro

Filamentoso)

• Disminución notoria de la salida del Humidificador. Por favor recuerde que si la humedad relativa es alta su humidificador producirá menos humedad.

• La cubierta superior del Filtro Filamentoso no se siente húmeda al tacto.

• El Filtro Filamentoso tiene agujeros y rasgaduras grandes.

El Filtro Filamentoso deber cambiarse al menos una o dos veces durante la temporada, dependiendo del uso, contenido mineral en el agua y el medio ambiente. Lo invitamos a utilizar sólo el

Reemplazo del Filtro

Filamentoso Honeywell HAC-700. El uso de otros Filtros Filamentosos puede resultar en un desempeño por debajo de lo normal

REEMPLAZAR SU FILTRO FILAMENTOSO (Continuación)

PASO 1 PASO 2 PASO 3

PASO 4

Reemplazo del Filtro

Filamentoso HAC-700

ó Filtro B.

PASO 5

Con las manos secas desconecte el humidificador y llévelo al baño o cocina.

PASO 6

Quite la rejilla superior y colóquela a un lado.

PASO 7

Retire los filtros filamentosos de la bandeja del filtro. Deseche los filtros filamentosos usados.

PASO 8

Sumerja los nuevos filtros en agua fría.

NO exprima los filtros.

Coloque los nuevos filtros en la bandeja del filtro.

LIMPIEZA: Series HCM-750

Vuelva a colocar la rejilla superior.

NOTA: Es recomendable que todos los mantenimientos sean realizados en la cocina o baño en una superficie resistente al agua.

Limpieza Semanal: Para limpiar adecuadamente su humidificador le recomendamos el proceso de eliminación de sarro y desinfección.

Seguro para Lavavajillas:

Las siguientes partes son seguras para la

CANASTILLA SUPERIOR del lavavajillas, para lavavajillas de uso residencial operando a temperaturas menores a los 70°C/158°F. Es recomendable que opere su lavavajillas en el ciclo suave o normal. No lave el humidificador con artículos/platos sucios.

NO UTILICE DETERGENTES. Si utiliza su lavavajillas para lavar las siguientes partes necesitará seguir el procedimiento de eliminación de sarro y desinfección.

Por favor Note: No coloque las partes en la canastilla inferior del lavavajillas. El hacerlo puede causar daño en las partes del humidificador y en el lavavajillas.

Embudo de Llenado

Cubierta

Transparente

Protectora

Manguera del Agua

Rejilla Superior

Bomba de agua

Bandeja del Filtro

Filamentoso

Deflector de Llenado de Agua

31

LIMPIEZA: Series HCM-750 (continuación)

La cubierta principal y los filtros filamentosos NO SON SEGUROS PARA EL

LAVAVAJILLAS.

El colocar estas partes en el lavavajillas dañará su humidificador y lo hará incapaz de funcionar adecuadamente.

Cubierta Principal

Filtros Filamentosos

Instrucciones para Eliminar el Sarro:

PASO 1

PASO 2 PASO 3

32

Retire la rejilla superior, los filtros, la bandeja del filtro, la bomba del agua, la manguera del agua, el deflector de llenado, la cubierta transparente protectora y el embudo de llenado de agua y póngalos a un lado.

Coloque los Filtros

Filamentosos a un lado.

Nota: Los filtros filamentosos no pueden someterse a la eliminación de sarro o desinfección. El hacerlo dañará los filtros y la unidad no operará adecuadamente.

Vacíe el agua del humidificador vertiéndola en la dirección del panel de control. Siga las flechas indicadoras ubicadas en el interior de la cubierta principal. Llene el depósito de agua de la cubierta principal con 2 tazas de vinagre.

PASO 4

PASO 5

PASO 6

Con la unidad desarmada, proceda con las instrucciones de desinfección.

Coloque la bomba de agua, la manguera del agua, el deflector de llenado de agua, la cubierta transparente protectora y el embudo de llenado dentro de la cubierta principal y remójelos en vinagre.

Gentilmente limpie la rejilla y la bandeja del filtro con vinagre sin diluir si decide no utilizar la opción del lavavajillas.

Sumerja durante 20 minutos. Enjuague la cubierta principal y las partes, no coloque en el lavavajillas hasta que el olor a vinagre haya desaparecido.

LIMPIEZA: Series HCM-750 (continuación)

Instrucciones de Desinfección: Disinfecte después de eliminar el sarro

PASO 1

PASO 2

PASO 3

1 gal

NOTA: UTILIZAR

MÁS DE 1 CUCH DE

CLORO POR GALÓN

DE AGUA PUEDE

PROVOCAR DAÑO EN

SU HUMIDIFICADOR.

NO DESINFECTE los

Filtros Filamentosos.

Deje a un lado la rejilla superior, la cubierta transparente protectora, la bandeja del filtro, la bomba del agua, la manguera del agua, el deflector de llenado de agua y el embudo de llenado.

Agregue 1 CUCH de cloro a 1 galón de agua.

Agregue 1 galón de la solución de agua/vinagre al depósito de agua de la cubierta principal. Utilizando esta mezcla limpie las paredes de la cubierta principal.

PASO 4 PASO 5

Remoje la manguera del agua, la bomba del agua, el deflector de llenado de agua, el embudo de llenado y la cubierta transparente protectora en el depósito de agua de la cubierta principal si estas partes no fueron lavadas en la canastilla superior del lavavajillas.

Sumerja durante 15-20 minutos.

Limpie la rejilla superior y la bandeja del filtro con la solución de agua/vinagre si estas partes no fueron lavadas en el lavavajillas.

Enjuague a fondo la cubierta principal y cualquier otra parte no colocada en el lavavajillas hasta que el olor a cloro desaparezca.

Note: Por favor cuide la ropa, tapetes, y otros materiales no resistentes al cloro cuando esté desinfectando. El derramar cloro en la ropa, tapetes y ciertas superficies puede causar daños.

33

REENSAMBLAJE: Series HCM-750

PASO 1

PASO 2 PASO 3

PASO 4

Inserte la salida de la bomba a la abertura de la manguera y presione gentilmente hasta que ya no avance más dentro del tubo de agua.

Inserte el ensamblaje de la bomba/manguera del agua dentro de la ranura en la cubierta principal.

Nota: la bomba entra solo en un sentido.

Coloque la manguera del agua en la cubierta principal insertando con gentileza la manguera del agua en la salida del agua.

Alinee el embudo de llenado con las ranuras ubicadas detrás de la ventana del agua.

Inserte con gentileza en su lugar.

PASO 5

PASO 6 PASO 7

34

Vuelva a insertar el deflector de llenado de agua al depósito de agua de la cubierta principal, alineando con las guías y empujando con cuidado hacia abajo para encajar.

Coloque la bandeja del filtros en la cubierta principal. Después vuelva a colocar los filtros en la bandeja del filtros.

Vuelva a colocar la rejilla superior y la cubierta transparente protectora.

CUIDADO Y ALMACENAJE DE FIN DE TEMPORADA

Siga las instrucciones de LIMPIEZA cuando el humidificador no esté en uso por al menos una semana o más, o al final de la temporada.

NOTA: Deseche los filtros usando y empiece con nuevo filtros la siguiente temporada.

Seque completamente el humidificador antes de almacenarlo.

NO almacene con agua en el depósito de agua de la cubierta principal o en el tubo de agua.

Empaque la unidad en la caja original y guarde en un lugar fresco y seco.

SERVICIO AL CONSUMIDOR

Envíe sus preguntas o comentarios a:

Kaz, Incorporated

Consumer Relations Dept.

250 Turnpike Road

Southborough, MA 01772 USA

Por favor especifique el número del modelo.

Llámenos al número de teléfono de llamada gratis de larga distancia:

1-800-477-0457

e-mail:

[email protected]

O visítenos en nuestro sitio web:

www.kaz.com

PARA ORDENAR PARTES DE REEMPLAZO

HAC-700 Reemplazo de Filtro Filamentoso

HCM-750 Rejilla (Rejilla Superior)

HCM-750 Bandeja del Filtro

(Bandeja del Filtro Filamentoso)

HCM-750 Cubierta

(Cubierta Transparente Protectora)

HCM-750 Nivel (Embudo de Llenado)

HCM-750 Pared de Llenado

(Deflector de Llenado de Agua)

750/200 Bomba (Bomba de agua)

HCM-750 Manguera (Manguera del Agua)

PC-2 Cartucho de Limpieza

Antimicrobiana Protec

MR

PREGUNTAS FRECUENTES

Limpieza

Pregunta

¿Cómo limpio el interior de la bomba de agua?

¿Qué partes son seguras para el lavavajillas?

Respuesta

Puede limpiar el interior de la bomba girando la cubierta hacia la izquierda. Retire la cubierta para limpiarla junto con el filtro.

La manguera del agua, la bomba del agua, la cubierta transparente protectora, la rejilla superior, la bandeja del filtro, el deflector de llenado de agua y el embudo del agua.

Vea la página 34 de su manual de usuario. ¿Cómo ensamblo mi humidificador después de limpiarlo?

¿Puedo utilizar detergente para platos para limpiar mi humidificador?

No es recomendable que utilice detergente para platos para limpiar su humidificador, ya que es muy difícil remover todo el detergente y puede causar daño a su humidificador. Es importante queNO utilice detergente si está utilizando su lavavajillas para limpiar estas partes.

35

PREGUNTAS FRECUENTES (Continuación)

Limpieza (Continuación)

Pregunta

¿Puedo agregar tratamientos de agua a este humidificador?

Respuesta

Sólo debe agregar a su humidificador los tratamientos de agua que son fabricados especialmente para humidificadores evaporativos tales como el

Cartucho de Limpieza Antimicrobiana Protect

MR

, modelo PC-1 ó PC-2. Utlizar tratamientos de agua que no son recomendados para humidificadores evaporativos puede dañar su humidificador. Si le preocupa la dureza del agua le recomendamos que utilice agua destilada en su humidificador.

36

Operación

Pregunta

¿En qué ajuste puedo colocar mi humidificador?

Utilicé mi humidificador toda la noche en una habitación muy seca y la humedad casi no cambió pero el nivel del agua disminuyó.

Respuesta

Usted debe operar su humidificador en el ajuste más alto si su habitación está muy seca. Una vez que tenga una humedad más cómoda usted puede cambiar el nivel de salida a un ajuste más bajo.

Puede tardar varios días en aumentar el nivel de humedad. Si está extremadamente seco, la madera, alfombras y otros objetos en su habitación pueden absorber la humedad antes que pueda sentir los efectos.

¿Puedo operar mi humidificador sin los filtros? No, su humidificador no puede operar adecuadamente sin los filtros. Los filtros absorben la humedad distribuida por el canal del flujo del agua. Después un ventilador silencioso soplará a través de los filtros distribuyendo la humedad en el aire.

¿Qué tan frecuente debo cambiar mis filtros filamentosos?

En general los filtros filamentosos pueden durar de

1 - 2 meses dependiendo de la calidad de agua y el uso. Consulte la sección de Cambio de Filtro para información de cómo determinar cuando es tiempo de cambiar los filtros.

¿Cómo se que mi humidificador está operando correctamente?

No puedo ver vapor saliendo de mi humidificador.

Usted notará que el agua fluye a través del canal de flujo de agua en la parte superior del humidificador.

También notará una disminución en el nivel de agua después de 8 horas de uso.

Su humidificador utiliza el proceso de evaporación.

Esto produce una humedad invisible ultra fina.

Observará que su nivel de agua disminuye y esto es un indicador que su humidificador está operando correctamente.

Vea la Guía de Solución de Problemas para mayor información.

PREGUNTAS FRECUENTES (Continuación)

Operación (Continuación)

Pregunta

No hay agua circulando en el área de circulación de agua en la cubierta superior.

¿Por qué mi humidificador repentinamente empezó a hacer un ruido fuerte?

¿Cuánta agua cabe en mi humidificador?

¿Cuánto tiempo funcionará mi humidificador cuando esté lleno?

Respuesta

Primero asegúrese que su humidificador tenga agua. Si es así, revise su bomba de agua para asegurarse que esté colocada correctamente en el área de soporte. Luego revise para asegurarse que la manguera del agua esté conectada firmemente a la bomba y a la salida del agua. Por último, asegúrese que nada obstruya el área del flujo del agua en la rejilla superior o en la manguera del agua.

Si estos pasos no ayudan, por favor consulte nuestra Guía de Solución de Problemas o contacte nuestro departamento de servicio al consumidor al

1-800-477-0457

Revise su nivel de agua. Si su humidificador empieza a hacer un ruido fuerte es un indicador que necesita rellenar su humidificador.

Su humidificador puede contener hasta 1.5 Gallones de agua.

Su humidificador operará hasta 17 horas en el ajuste alto y 48 horas en el ajuste bajo.

37

SOLUCIÓN DE PROBLEMAS

1. No está fluyendo el agua

a. Revise para asegurarse que el tanque tenga agua y que esta cubra la bomba.

b. Revise la manguera del agua y asegúrese que no esté torcida. La manguera debe conectarse completamente en la salida del agua y en la bomba.

c. Asegúrese que la bomba esté colocada correctamente en la ranura en el fondo de la cubierta principal.

d. Apague la unidad y después vuélvala a encender para ayudar a eliminar algún aire en el sistema.

e. Si todavía no circula el agua, saque la bomba, desármela y asegúrese que la rueda de la bomba gire libremente y que las entradas de la bomba u otros pasajes de agua no tengan obstrucciones.

f. Asegúrese que la rejilla esté bien colocada y pueda aceptar agua del embudo.

2. La unidad circula el agua pero no produce vapor

a. Esta unidad no produce vapor visible.

3. La unidad circula el agua pero el filtro no está humedo

a. Revise para asegurarse que los agujeros de la característica de agua no estén bloqueados y puedan gotear agua en los filtros.

4. La bomba hace un sonido siseante

a. La bomba puede haber succionado aire. Asegúrese que haya suficiente agua en el tanque para que cubra la bomba.

b. Después de llenar, apague la unidad por unos segundos, después enciéndala de nuevo para eliminar el aire en el sistema.

5. La bomba tiene un zumbido

a. La bomba puede no estar colocada correctamente. Asegúrese de empujar completamente la bomba en la ranura en la cubierta principal. Después de colocar la bomba correctamente, apague la unidad por unos segundos, después vuélvala a encender.

Esto permitirá que la bomba se sincronice con el imán impulsor.

6. La unidad tiene poca salida

a. Asegúrese que los filtros estén humedos y pueda sentir circulación de aire saliendo del filtro. b. Asegúrese que el deflector de llenado de agua y la rejilla estén colocados correctamente.

c. Si ambos a y b están BIEN, la humedad relativa de su hogar debe estar alta. La unidad regulará automáticamente la salida basada en la cantidad de humedad que esté en el aire.

38

7. La unidad hace un sonido de goteo o escurrimiento

a. Asegúrese que el embudo de llenado esté correctamente armado y montado en el tanque detrás de la ventana del agua. b. Asegúrese que la rejilla esté colocada correctamente y que el embudo de llenado pueda aceptar agua.

c. Asegúrese que la malla que soporta al filtro no esté dañada.

3 AÑOS DE GARANTÍA LIMITADA

Usted debe leer primero todas las intrucciones antes de intentar utilizar este producto.

A. La presente garantía limitada de 5 años cubre la reparación o remplazo del producto si éste presenta un defecto de fábrica o de mano de obra. Esta garantía excluye todo daño resultante del uso comercial, abusivo o inadecuado del producto, o de daños asociados. De igual manera no aplica al filtro o Cartucho Antimicrobiano Protect MR . Las defectos resultantes del desgaste normal no se consideran defectos de fábrica en virtud de la presente garantía.

KAZ QUEDA EXENTA DE TODA

RESPONSABILIDAD POR LOS DA-

ÑOS FORTUITOS O INDIRECTOS DE

CUALQUIER CLASE. CUALQUIER

GARANTÍA IMPLÍCITA DE CALIDAD

COMERCIAL O DE CONVENIENCIA

RELACIONADA CON ESTE PRODUCTO,

TENDRÁ LA MISMA VIGENCIA QUE LA

PRESENTE GARANTÍA.

En ciertos lugares, no se permite la exclusión o limitación de daños fortuitos o indirectos, ni los límites de duración aplicables a una garantía implícita. Por consiguiente, es posible que estas limitaciones o exclusiones no se apliquen en su caso. Esta garantía le otorga derechos legales específicos y usted puede que tenga otros, que varían de un lugar a otro. La presente garantía sólo es válida para el comprador original del producto a partir de la fecha de compra.

B. A su juicio, Kaz reparará o reemplazará este producto si se considera que sus materiales o su mano de obra son defectuosos dentro del período de garantía.

C. Esta garantía no cubre daños ocasionados por tentativas no autorizadas de reparar el producto o del uso del mismo en contravención de las indicaciones que aparecen en el manual de instrucciones.

D. Devuelva el producto defectuoso, con flete pagado y prueba de compra, junto con cheque o giro postal por $10.00 US/$15.50

CAN para cubrir gastos de administración, empaque de regreso y envío. Por favor incluya su nombre, dirección y un número de teléfono para comunicarse durante el día.

Los gastos de envío deben pagarse por

adelentado. Le sugerimos que pida confirmación del seguimiento o de la entrega. Mande el envío a:

En los Estados Unidos:

Kaz, Incorporated

Attn: Returns Department

4755 Southpoint Drive

Memphis, TN 38118

USA

En Canada:

Kaz Canada, Inc.

Attn: Returns Department

510 Bronte Street South

Milton, ON L9T 2X6

Canada

Por favor visite www.kaz.com y registre su producto en el Centro de Atención al Cliente y reciba información y actualizaciones de su productos y nuevas ofertas promocionales.

©2010 Kaz, Incorporated.

Todos los derechos reservados

P/N: 31IMM750190

39

40

advertisement

Related manuals

advertisement