Danuser EP2035 Operator Manual

EP
AUGER SYSTEMS
EP615
EP1020
EP1530
EP2035
Read this entire manual. This
safety alert symbol is used
throughout this manual to call your
attention to messages involving
your personal safety and the safety
of others. Failure to follow these
instructions can result in injury or
death.
WARNING
Si no entiende ingles, se prefiere que
busque a alguien que interprete las
instrucciones para usted.
Owner:
Date Purchased:
Model #:
Serial #:
Manual #:
9MEP2460098
Operator’s Manual
Danuser Machine Company
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246 Fax: (573) 642-2240
E-mail: [email protected]
Website: www.danuser.com
Dear Owner/Operator,
Thank you for purchasing this Danuser Hydraulic Earth Auger. We appreciate your business.
The EP Auger System is designed to meet the needs of farmers, ranchers, contractors, landscapers,
and municipalities. Various auger styles are available for drilling in light ground conditions to
harder ground conditions, such as rock, frozen ground, and more.
Your safety as an operator of our product is very important to us. Therefore, before you assemble,
install, operate, maintain, service, remove, or move your Danuser Earth Auger, read and understand
this manual thoroughly. If there is anything you do not understand, immediately contact your
dealer, or contact our factory direct.
Phone:
Fax:
E-mail:
(573) 642-2246
(573) 642-2240
[email protected]
Your satisfaction in the performance and longevity of our product is also very important to us and
can be prolonged by proper assembly, installation, operation, and maintenance as instructed in this
manual.
Thank you again for your business and for your trust in our product. Please feel free to contact us at
any time for further assistance.
Sincerely,
Danuser Machine Company
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected]
Fax: (573) 642-2240
Website: www.danuser.com
Danuser provides this manual "as is" without warranty of any kind, either expressed or implied. Danuser assumes
no responsibility for errors or omissions. Danuser assumes no liability for damages resulting from the use of the
information contained herein. Danuser reserves the right to revise and improve its products as it sees fit. This manual
describes the state of this product at the time of its publication and may not reflect the product in the future.
Danuser is a registered trademark.
Foreword
Please read this manual thoroughly!
Before you assemble, install, operate, maintain, service, remove, or move your Danuser
Earth Auger, read this manual thoroughly. If there is anything you do not understand,
immediately contact your dealer, or call our factory direct at (573) 642-2246. Powered
equipment can be dangerous if not assembled, installed, operated, maintained, serviced,
removed, or moved properly.
Warranty Registration
To activate your warranty coverage and to provide you with efficient customer service,
please fill out your WARRANTY REGISTRATION FORM. This form is included in your
unit’s paperwork package. If you did not complete a WARRANTY REGISTRATION
FORM or did not receive one, please call Danuser Machine Company. Or, register online at
www.Danuser.com. Your satisfaction with our product and your safety as a user of our
product are both very important to us.
Symbols
This SAFETY ALERT symbol identifies important safety messages. Carefully read
each safety message that follows. Failure to understand and obey a safety message,
or recognize a safety hazard, could result in injury or death to you or others around you.
The operator is ultimately responsible for the safety of himself, as well as others, in the
operating area of the earth auger.
Symbol
Meaning
an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
DANGER Indicates
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury,
including hazards that are exposed when guards are
removed.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTE
Table of
Contents
This is important information for proper use of this
equipment. Failure to comply may lead to premature
equipment failure.
Page
Letter to the Owner/Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Decals & Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Drive Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hydraulic Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assembly & Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removal & Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Maintenance & Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Augers & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD 5022
3
Safety
WARNING
Working with unfamiliar equipment can lead to careless injuries. Read and understand this manual and
the manual for your vehicle before assembling, installing, operating, maintaining, servicing, removing, or
moving this earth auger. If there is anything in this manual you do not understand, contact your dealer or
Danuser Machine Company. The safe use of this machine is strictly up to you, the operator. If this unit is
used, loaned, or rented by any other person, it is the owner's responsibility to make certain that the operator
prior to operating:
•
•
Reads and understands the Operator's Manuals
Is instructed in safe and proper use
There is an entanglement risk if you replace the special auger retaining bolt with a bolt longer than
specified by Danuser Machine Company. This improper replacement occurs most often on machines that
are loaned or rented to someone who has not read the Operator's Manual and is not familiar with an earth
auger.
4
•
This earth auger is designed for one-man operation from the vehicle seat. It is the responsibility of
the operator to see that no one is within twenty-five feet (25') of the earth auger when it is started or
in use. Do not operate the earth auger with another person near or in contact with any part of the
drive unit or auger. Serious personal injury or death may result if any attempt is made to assist
drilling operation by hand.
•
All operators of this attachment must read and understand this entire manual, paying particular
attention to safety messages and operation instructions, prior to assembling, installing, operating,
maintaining, servicing, removing, or moving the earth auger.
•
Please remember it is also important that you read, understand, and follow the safety signs on the
attachment. Clean or replace all safety signs if they cannot be clearly read and understood. They are
there for your safety as well as the safety of others. Danuser Machine Company will furnish new
safety signs upon request at no charge.
•
All things with moving parts are potentially hazardous. There is no substitute for a cautious,
safe-minded operator who recognizes potential hazards and follows reasonable safety practices.
•
Personal protection equipment including hard hat, safety glasses, safety shoes, and gloves are
recommended during assembly, installation, operation, maintenance, service, removal, or movement
of the attachment.
•
When the use of hand tools is required to perform any part of assembly, installation, maintenance,
service, removal, or movement of the earth auger, be sure the tools used are designed and
recommended by the tool manufacturer for that specific task.
•
Never check pressurized system for leaks with your bare hand. Wear proper hand and eye protection
and use wood or cardboard when searching for suspected leaks. Oil escaping from pinhole leaks
under pressure can penetrate skin and create a serious medical emergency. If any fluid is injected into
the skin, gangrene, blood poisoning, even death may result. Obtain medical attention immediately.
•
Always use two people to handle heavy, unwieldy components during assembly, installation,
maintenance, service, removal, or movement of the attachment.
•
Never place any part of your body where it would be in danger if movement should occur during
assembly, installation, operation, maintenance, service, removal, or movement of the earth auger.
•
Check clearances between vehicle and auger, as well as operator and auger, across the full range of
loader arms operating heights. Keep earth auger drive unit in cradle when not drilling.
•
Only properly trained people should operate this equipment. Do not allow anyone who has not read
this entire manual and understood the safety rules, safety signs, and operation instructions to use this
attachment.
•
Never allow children to operate or be around this earth auger.
Safety
(continued)
•
Do not allow riders on the equipment at any time. There is no safe place for any riders.
•
Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating
this equipment. Consult your doctor about operating this equipment while taking prescription
or over-the-counter medications.
•
Safe operation of equipment requires the operator's full attention. Avoid distractions such as radio
headphones, cell phones, etc. while operating.
•
Contact with underground gas lines or electrical cables may result in serious injury or death from
explosion or electrical shock. Before operating, call 811 or the local number to locate underground
utilities.
•
Do not drill near underground utility lines.
•
Before beginning operation, clear the work area of objects which might be picked up and thrown by
or entangled in the auger.
•
The earth auger must be securely latched to the vehicle. Ensure quick attach latching method is
properly secured. An improperly latched earth auger can fall without warning.
•
Before you operate the attachment, check over all pins, bolts, and connections to be sure all are
securely in place. Replace any damaged or worn parts immediately.
•
Never replace the auger retaining bolt with anything other than the specified length bolt in this
manual. A longer, or protruding, fastener is more likely to grab clothing or gloves, which can result
in serious injury or death.
•
Keep all helpers and bystanders twenty-five feet (25') away from an operating earth auger.
•
Keep hands, feet, hair, jewelry, and clothing away from all moving and/or rotating parts.
•
Never place yourself between the vehicle and the attachment.
•
Worn teeth or a slightly rounded point can seriously affect auger penetration. Check for wear before
each use, and replace as necessary.
•
Never position the auger point by hand or with any tool when the vehicle is running.
•
Never position the auger point by putting your hands on the auger or drive unit.
•
Do not shovel dirt away from a rotating auger, as the shovel can be caught and thrown by the auger.
•
Never transport with the drive unit out of the cradle or while the auger is rotating.
•
Do not exceed the vehicle’s rated operating load. Use sufficient counterweights. Move the vehicle
slowly when the attachment is raised.
•
A heavy load can cause instability of the vehicle. Use extreme care during travel. Slow down on
turns and watch out for bumps. Use all safety devices, including a seat belt, as recommended in the
vehicle operator’s manual.
•
Do not operate the earth auger on steep hillsides. When drilling on uneven or hilly terrain, position
the vehicle with the earth auger uphill. With the earth auger downhill, the vehicle could tip when
attempting to raise the auger from its hole. Consult your vehicle operator’s manual for maximum
incline allowable.
•
Always shut off the vehicle engine, remove the key, lower vehicle arms, and relieve all hydraulic
pressure before dismounting the vehicle. Never leave equipment unattended with the vehicle
running.
5
Safety
•
Never attempt adjustments, service, or repairs while the equipment is in operation.
•
Never work under equipment supported by hydraulics. Even with the vehicle shut off, equipment can
suddenly drop if controls are actuated or if hydraulic lines burst.
•
Before connecting or disconnecting hydraulic lines or fittings, be sure to relieve all pressure by
cycling all hydraulic controls after shutdown. Remember hydraulic systems are under pressure
whenever the engine is running and may hold pressure after shutdown.
•
Store the attachment on a flat, level surface in an area where children do not play. Securely block
and support the attachment.
•
Do not modify the attachment. Modifications may weaken the integrity of the attachment and may
impair the safety, function, life, and performance of the earth auger.
•
When making repairs or servicing the earth auger, use only parts that meet original equipment
manufacturer's standards and requirements.
•
Always use care when operating the earth auger. Most accidents occur because of neglect or
carelessness.
(continued)
Safety is a primary concern in the design, manufacture, sale, and use of earth augers. Danuser confirms to
you, our customer, our concern for safety.
DANGER
Improper operation of this earth auger can cause serious
personal injury or death. Operation of this earth auger
should only be done by a competent adult acting in
compliance with the Operator's Manual. Since drilling
operations are beyond our control, we disclaim all liability
for any damages, injuries, or death which may result.
WARNING
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
6
Decals &
Safety Signs
The earth auger comes equipped with all safety signs in place. Their locations are shown in
this section. Read and follow their instructions and ensure their care:
•
•
•
Keep safety signs clean and legible at all times.
Replace safety signs that are missing, illegible, or damaged.
Ensure replacement parts installed during repair have safety signs attached.
To install new safety signs, follow these steps:
1.
2.
3.
4.
MODEL:
SERIAL NO:
Clean the area where the safety sign is to be placed.
Spray a little soapy water on the surface where the safety sign is to be placed.
Peel the backing from the safety sign, and apply it in the position shown.
Firmly press the safety sign, and squeeze out the air bubbles with a straight edge (e.g., a
credit card).
Model No. & Serial No.
Location: Drive unit,
inside right rear
PART NO. CA65
Location: Drive unit, rear
PART NO. DIG5
Location: Drive unit,
left side
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
(573) 642-2246
danuser.com
PART NO. DIG56
Location: Drive unit,
right side
PART NO. DANUSER107
Location: Drive unit, front
PART NO. 196048
Location: Drive unit,
front
PART NO. 196047
Location: Drive unit,
rear
PART NO. 190148 (EP615)
PART NO. 190149 (EP1020)
PART NO. 190150 (EP1530)
PART NO. 190151 (EP2035)
Location: Drive unit, front
PART NO. DIG8
Location: Auger
WARNING
Clean or replace all safety
signs if they cannot be
clearly read and understood.
PART NO. DIG55
Location: Drive unit, left side;
Drive unit, right side
7
Decals &
Safety Signs
Backhoe & Excavator
Pin-on Mount Kit 1" - 40mm Pin Sizes
Backhoe & Excavator
Pin-on Mount Kit 1-5/8" - 55mm Pin Sizes
(continued)
PART NO. DANUSER108
Locations: Frame, front; Frame, rear
Backhoe & Excavator
Quick Attach
PART NO. DANUSER106
Locations: Quick attach plate, left side;
Quick attach plate, right side
PART NO. DIG35
Location: Quick attach plate, top
Mini-Skid-Steer Quick Attach
NOTE
Skid-Steer Quick Attach Center & Offset
John Deere 200-500 Series
Quick Attach
Bobcat MT Quick
Attach Uses
DANUSER106
PART NO. DIG57
Location: Quick attach plate, top
PART NO. DIG41
Location: Quick attach plate, top
WARNING
8
Euro/Global
Quick Attach
Clean or replace all safety
signs if they cannot be
clearly read and understood.
Drive Unit
Specifications
Operator's Manual
Direction Terminology
Front
B
Right
Left
Rear
A
EP Auger Systems
Model EP615
Model EP1020
Overall Width (A)
10"
Overall Height (B)
29"
Model EP1530
Model EP2035
Weight
141 lb.
142 lb.
143 lb.
143 lb.
Minimum Hydraulic Flow
6 GPM
10 GPM
15 GPM
20 GPM
Maximum Hydraulic Flow
15 GPM
20 GPM
30 GPM
35 GPM
36"
36"
Maximum Continuous Operating Pressure
3,500 PSI
Maximum Auger Diameter
24"
30"
Output Spindle
2" Hex
Model EP1020
Model EP615
GPM
6
8
10
12
14
15
GPM
10
12
14
16
18
20
RPM
36
48
60
73
85
91
RPM
48
58
68
77
87
97
PSI
2,000
2,500
3,000
3,500
PSI
2,000
2,500
3,000
3,500
TORQUE
1,014 ft.-lb.
1,267 ft.-lb.
1,520 ft.-lb.
1,774 ft.-lb.
TORQUE
1,270 ft.-lb.
1,587 ft.-lb.
1,904 ft.-lb.
2,222 ft.-lb.
Model EP2035
Model EP1530
GPM
15
18
20
24
28
30
GPM
20
22
26
30
32
35
RPM
49
59
65
78
92
98
RPM
48
53
63
73
78
85
PSI
2,000
2,500
3,000
3,500
PSI
2,000
2,500
3,000
3,500
TORQUE
1,874 ft.-lb.
2,342 ft.-lb.
2,811 ft.-lb.
3,279 ft.-lb.
TORQUE
2,529 ft.-lb.
3,161 ft.-lb.
3,794 ft.-lb.
4,426 ft.-lb.
Torque and output speed specifications are based on theoretical values and are provided for comparative purposes only.
9
Hydraulic
Requirements
Filtration Requirements:
• A filter of, at least, 25 micron filtration is required. A filter capable of 10 micron
filtration is preferred. The majority of paper type filters are 25 microns or better.
NOTE
The life of the hydraulic motor is almost entirely dependent upon cleanliness
of the oil. Instructions in your vehicle operator’s manual regarding filter and
oil changes should be carefully followed. Even small amounts of dirt in the
hydraulic oil can cause premature motor failure that is not covered by warranty.
•
A low pressure type filter can be installed in the return line from the control valves to
the sump. A low pressure type filter can also be installed in the sump or pump intake
line but must be sized large enough to avoid starving the pump.
•
A high pressure type filter can be used between the pump and the control valves.
•
If the source of the hydraulic power does not have a filter, it will be necessary to install
one at some point in the system so, at least, part of the hydraulic oil is being filtered whenever the system is operating. After a filter is installed and before attaching the
drive unit, the entire hydraulic system should be drained, filled with new oil, and
operated for 30 minutes or until the system is warm. During this run time, operate all
valves, cylinders, and hydraulic motors on the machine.
Pressure and Flow Requirements:
• Models EP615, EP1020, EP1530, and EP2035 Danuser Earth Augers are designed to
operate within the pressure range of 1,500 to 3,500 PSI.
,
For vehicles delivering higher than 3,500 PSI, a cross port relief valve is
NOTE
available. Refer to Accessories section.
•
Operating flow rate is dependent on model: 6 to 15 GPM for Model EP615, 10 to 20
GPM for Model EP1020, 15 to 30 GPM for Model EP1530, and 20 to 35 GPM for Model EP2035.
Valve Requirements:
• The hydraulic system used to power the drive unit should be equipped with a four-way valve large enough to carry full pump outlet without restricting flow and causing oil heating.
•
The four-way valve requires a relief valve which will open and relieve extreme
pressures between the drive unit and control valve, even when the control valve is in a
neutral position. This feature can be obtained by connecting two external relief valves
between the main lines running from the control valve to the drive unit in such a way
that high pressure in either line will be relieved to the other line.
Hydraulic Hose Requirements:
• High pressure hoses of, at least, 1/2" inside diameter connect four-way valve to the hydraulic fittings on the top of the drive unit.
•
Working pressure of hydraulic hoses must be higher than the rated vehicle hydraulic pressure.
•
An abrasion sleeve is recommended on all hydraulic hoses.
•
The drive unit is equipped with two 45° adapters to which hoses can be connected. These
adapters are #10 JIC M.
•
Since the motor is reversible, hose connections to motor fittings are interchangeable.
•
All hoses, pipes, adapters, and fittings used to connect the drive unit should be thoroughly
cleaned before use. Care should be taken to see that no thread sealer or metal chips are
forced to the inside of the joints when connections are being tightened.
Hydraulic Fluid Selection Requirements:
• Premium grade petroleum based fluids will provide the best performance.
10
•
Fluids that contains anti-wear agents, rust inhibitors, anti-foaming agents, and oxidation
inhibitors are recommended.
•
The viscosity of the fluid should never fall below 70 SUS (13 cSt). The best viscosity range for the drive unit is 100-200 SUS (20-43 cSt).
Assembly &
Installation
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
Assembly &
Installation
Skid-Steer, Euro/Global,
& John Deere 200-500
Series Quick Attach
Mounted Earth Auger
CAUTION
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
Prepare the Vehicle
Read and understand the manual for your vehicle before assembling or installing the EP
Auger System. The vehicle must be equipped with auxiliary hydraulics and either a quick
attach, dipperstick, or bucket for use with the bolt-on bucket mount.
The use of the earth auger may require the addition of counterweights to ensure the weight of
the attachment does not exceed the rated capacity of your vehicle.
WARNING
Do not exceed the vehicle's rated operating load.
If necessary, use sufficient counterweights.
Recommended Tools
• Box cutter/metal snips
STEP 1:
Remove pallet, banding, and any other packaging materials from the earth auger.
STEP 2:
Inspect product for damage.
Proceed to the section below that matches your mounting style.
The quick attach mount allows the cradle to be installed in two different positions, allowing
the drive unit to lie at either a 15° or 30° carry angle during transport. The 15° carry angle
provides better operator visibility while transporting the earth auger, but reduces the clearance
between cradle and drive unit housing during drilling operations.
NOTE
NOTE
NOTE
Additional factors that influence clearance between cradle and drive unit include:
• Length of auger
• Maximum tilt angle of vehicle
• Angle of hole being drilled
• Slope of ground
The cradle mounting bolt holes closer to
the drive unit set the carry angle at 15°.
The bolt holes further from the drive unit
set the carry angle at 30°.
15°
It is recommended to install the cradle in the 15° carry angle, provided the cradle
does not come into contact with the drive unit housing during drilling operations.
Damage may occur if the cradle comes into contact with the drive unit housing
during drilling operations.
Recommended Tools
• 1-1/8" wrench
• 1-1/8" socket
STEP 1:
30°
•
•
1-7/16" wrench
9/16" socket
•
•
1/2" wrench (2)
7/8" wrench
•
•
Torque wrench
1" wrench
Bolt left and right cradle arms (1, 2) and cradle center plate (3) together with 3/8"
carriage bolts (4) and 3/8" nuts (5). Tighten by hand only.
4
2
3
5
1
11
Assembly &
Installation
STEP 2:
(continued)
Using a 1-1/8" wrench and torque wrench with 1-1/8" socket, bolt cradle assembly
(7) to quick attach plate assembly (6) with 3/4" bolts (8) and washers (9), and
secure with 3/4" nuts (10) and washers (9).
10
6
9
8
NOTE
7
On the skid-steer quick attach, the cradle may be bolted to the quick attach plate
in either a center position or an offset position, as in the images below. Center
mounting of the cradle is preferred when using the earth auger on a skid-steer,
while offset mounting will provide better visibility when used on a tractor frontend loader.
Offset cradle installation
Center cradle installation
STEP 3:
Using a torque wrench with 9/16" socket, tighten 3/8" nuts (5).
STEP 4:
Park the vehicle on level ground, and install the quick attach plate assembly by
following your vehicle operator's manual for installing an attachment.
WARNING
The earth auger must be securely latched to the vehicle.
Ensure quick attach latching method is properly secured.
An improperly latched earth auger can fall without warning.
6
16
12
15
11
14
13
12
STEP 5:
Attach the wider end of the knuckle assembly (11) to the drive unit (12) using pin
(13). Secure pin (13) with lock pin (14).
STEP 6:
Attach knuckle assembly/drive unit to the quick attach plate assembly (6) using
pin (15). Align pin (15) head with slot on quick attach plate assembly (6). Secure
pin (15) with klik pin (16).
Assembly &
Installation
STEP 7:
(continued)
NOTE
NOTE
STEP 8:
NOTE
STEP 9:
If you purchased Danuser Hose Kits PN 196025 or PN 196027, install by using a
7/8" wrench and a 1" wrench to tighten the hose connections onto the 45° adapters
on the drive unit.
All hoses and fittings used to connect the earth auger should be thoroughly cleaned
before use. Care should be taken to see that no thread sealer or metal chips are
forced to the inside of the joints when connections are being tightened.
Since the hydraulic motor is reversible, hose connections to motor fittings are
interchangeable.
Using a 1-7/16" wrench and a 1" wrench, tighten the hydraulic quick couplers onto
the hoses.
Danuser Hose Kit PN 196025 does not include hydraulic quick couplers. You
must obtain the proper hydraulic quick couplers for your particular vehicle.
Install the hose holder spring kit in the desired mounting location. The quick attach
mount uses a hose holder spring kit to allow adjustment of hose routing, reducing
pinching, kinking, and stretching. The hose holder spring kit may be mounted left
or right of center on the quick attach plate. For center cradle installations, it is
recommended to install the hose holder spring kit in the mounting position nearest
the vehicle's hydraulic valve block. For offset cradle installations, the desired spring
mounting location will vary based on the location of the vehicle's hydraulic valve
block. The vehicle loader arm and operator step configuration also may affect the
desired spring mounting location.
Skid-Steer Quick Attach,
center cradle position
Right spring mounting location
Left spring mounting location
Right spring mounting location
Left spring mounting location
Skid-Steer Quick Attach,
offset cradle position
NOTE
Each vehicle may require different positioning of the hose holder spring kit, and of
the hoses as they pass through the clamp.
NOTE
The hose holder spring kit will suit 1/2" diameter hoses only.
STEP 10: Tighten the hose holder spring mounting nut. Using two 1/2" wrenches, loosen the hose
clamp assembly, route the hydraulic hoses through the clamp assembly, and reattach the
hardware.
STEP 11: If routing hoses to the right of center, using a 7/8" wrench, orient the 45° adapters
on the drive unit toward the hose holder spring kit. The 45° adapters come from
the factory oriented to accommodate the left spring mounting location.
13
Assembly &
Installation
STEP 12: Connect the quick couplers to the vehicle's auxiliary hydraulic outlets.
NOTE
Ensure quick couplers are clean prior to connection.
WARNING
(continued)
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is
running and may hold pressure after shutdown.
WARNING
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
STEP 13: Test the vehicle to make sure you have adequate hose length throughout the full
operating range of the vehicle's loader arms. Adjust the position of the hoses as
necessary to avoid pinching, kinking, or stretching.
NOTE
Hose routing is the responsibility of the operator. Pinched, kinked, and/or stretched
hoses are not covered under the warranty.
STEP 14: With the vehicle set at idle, engage the auxiliary hydraulics and verify output spindle
rotation. The output spindle should rotate clockwise when viewed from above.
STEP 15: Check the hydraulic system for leaks.
WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
Proceed to Assembly & Installation: Auger, Extension, & Adapter section.
Assembly &
Installation
Mini-Skid-Steer
Quick Attach Mounted
Earth Auger
Recommended Tools
• 1-1/8" wrench
• 1-1/8" socket
STEP 1:
•
•
•
•
1/2" wrench (2)
7/8" wrench
•
•
Torque wrench
1" wrench
Bolt left and right cradle arms (1, 2) and cradle center plate (3) together with 3/8"
carriage bolts (4) and 3/8" nuts (5). Tighten by hand only.
4
2
5
14
1-7/16" wrench
9/16" socket
3
1
Assembly &
Installation
STEP 2:
Using a 1-1/8" wrench and torque wrench with 1-1/8" socket, bolt cradle assembly
(7) to quick attach plate assembly (6) with 3/4" bolts (8) and washers (9), and
secure with 3/4" nuts (10) and washers (9).
(continued)
6
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
9
8
10
7
STEP 3:
Using a torque wrench with 9/16" socket, tighten 3/8" nuts (5).
STEP 4:
Park the vehicle on level ground, and install the quick attach plate assembly by
following your vehicle operator's manual for installing an attachment.
WARNING
CAUTION
The earth auger must be securely latched to the vehicle.
Ensure quick attach latching method is properly secured.
An improperly latched earth auger can fall without warning.
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
11
16
12
15
6
14
13
STEP 5:
Attach the wider end of the knuckle assembly (11) to the drive unit (12) using pin
(13). Secure pin (13) with lock pin (14).
STEP 6:
Attach knuckle assembly/drive unit to the quick attach plate assembly (6) using
pin (15). Align pin (15) head with slot on quick attach plate assembly (6). Secure
pin (15) with klik pin (16).
STEP 7:
If you purchased Danuser Hose Kits PN 206031 or PN 206032, install by using a
7/8" wrench and a 1" wrench to tighten the hose connections onto the 45° adapters
on the drive unit.
NOTE
NOTE
All hoses and fittings used to connect the earth auger should be thoroughly cleaned
before use. Care should be taken to see that no thread sealer or metal chips are
forced to the inside of the joints when connections are being tightened.
Since the hydraulic motor is reversible, hose connections to motor fittings are
interchangeable.
15
Assembly &
Installation
(continued)
STEP 8:
NOTE
STEP 9:
NOTE
Using a 1-7/16" wrench and a 1" wrench, tighten the hydraulic quick couplers onto
the hoses.
Danuser Hose Kit PN 206031 does not include hydraulic quick couplers. You
must obtain the proper hydraulic quick couplers for your particular vehicle.
17
Install the hose holder spring kit (17) onto
the quick attach plate (6). The quick attach
mount uses a hose holder spring kit to allow
adjustment of hose routing, reducing
pinching, kinking, and stretching.
The hose holder spring kit will suit 1/2"
diameter hoses only.
STEP 10: Tighten the hose holder spring mounting nut.
Using two 1/2" wrenches, loosen the hose clamp
assembly, route the hydraulic hoses through the
clamp assembly, and reattach the hardware.
STEP 11: Connect the quick couplers to the vehicle's
auxiliary hydraulic outlets.
NOTE
6
Drive Unit not pictured
for clarity
Ensure quick couplers are clean prior to connection.
WARNING
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is
running and may hold pressure after shutdown.
WARNING
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
STEP 12: Test the vehicle to make sure you have adequate hose length throughout the full
operating range of the vehicle's loader arms. Adjust the position of the hoses as
necessary to avoid pinching, kinking, or stretching.
NOTE
Hose routing is the responsibility of the operator. Pinched, kinked, and/or
stretched hoses are not covered under the warranty.
STEP 13: With the vehicle set at idle, engage the auxiliary hydraulics and verify output spindle
rotation. The output spindle should rotate clockwise when viewed from above.
STEP 14: Check the hydraulic system for leaks.
WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
Proceed to Assembly & Installation: Auger, Extension, & Adapter section.
16
Assembly &
Installation
Recommended Tools
• 1-1/8" wrench
STEP 1:
Backhoe & Excavator
Quick Attach Mounting Kit
CAUTION
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
Torque wrench
•
1-1/8" socket
•
9/16" socket
Bolt left and right cradle arms (1, 2) and cradle center plate (3) together with 3/8"
carriage bolts (4) and 3/8" nuts (5). Tighten by hand only.
4
2
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
•
3
1
5
STEP 2:
Align cradle assembly (7) onto quick attach plate assembly (6) such that the bolt
holes in the quick attach plate align with the cradle mounting bolt holes closer to
the drive unit.
Bolt holes further from drive unit
are not used with the Backhoe &
Excavator Quick Attach Mounting Kit
7
Install cradle mounting bolts in
bolt holes closer to drive unit
STEP 3:
Using a 1-1/8" wrench and torque wrench with 1-1/8" socket, bolt cradle assembly
(7) to quick attach plate assembly (6) with 3/4" bolts (8) and washers (9), and
secure with 3/4" nuts (10) and washers (9).
6
9
8
7
10
STEP 4:
Using a torque wrench with 9/16" socket, tighten 3/8" nuts (5).
STEP 5:
Park the vehicle on level ground, and install the quick attach plate assembly by
following your vehicle operator's manual for installing an attachment.
WARNING
The earth auger must be securely latched to the vehicle.
Ensure quick attach latching method is properly secured.
An improperly latched earth auger can fall without warning.
17
Assembly &
Installation
16
(continued)
11
15
6
STEP 6:
Attach the wider end of the knuckle assembly (11) to the drive unit (12) using pin
(13). Secure pin (13) with lock pin (14).
STEP 7:
Attach knuckle assembly/drive unit to the quick attach plate assembly (6) using
pin (15). Align pin (15) head with slot on quick attach plate assembly (6). Secure
pin (15) with klik pin (16).
Proceed to Assembly & Installation: Backhoe & Excavator Hose Routing section.
Assembly &
Installation
Backhoe & Excavator
Pin-on Mounting Kit
Recommended Tools
• 3/4" socket
CAUTION
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
18
Torque wrench
STEP 1:
Attach drive unit (1) to the knuckle sub-assembly (2)
using pin (3). Secure pin (3) with lock pin (4).
STEP 2:
Park the vehicle on level ground. Remove
bucket from dipperstick, and curl cylinder pin
connections. The dipperstick pin will be used to
attach the knuckle assembly to the dipperstick. The curl cylinder pin will not be required for drive
unit installation.
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
•
STEP 3:
NOTE
STEP 4:
Space the two ear assemblies (5) to the width of the
dipperstick, and use a torque wrench with 3/4" socket
to secure the ears to the knuckle sub-assembly (2) with
1/2" U-bolts (6) and 1/2" nuts (7). The ear assemblies
should be spaced evenly from the center of the
knuckle sub-assembly.
Check and re-torque nuts (7) after the first
hour of use.
4
2
3
1
7
5
Attach knuckle assembly/drive unit to the
dipperstick using the dipperstick pin removed from
the bucket in STEP 2. Secure the bucket pin per
vehicle manufacturer’s recommendations.
Proceed to Assembly & Installation: Backhoe &
Excavator Hose Routing section.
6
2
Assembly &
Installation
Recommended Tools
• 7/8" wrench
STEP 1:
Backhoe & Excavator
Hose Routing
•
1" wrench
•
1-7/16" wrench
If you purchased Danuser Hose Kits PN 196025, 196027, 206031, or 206032,
install by using a 7/8" wrench and a 1" wrench to tighten the hose connections
onto the 45° adapters on the drive unit.
NOTE
All hoses and fittings used to connect the earth auger should be thoroughly cleaned
before use. Care should be taken to see that no thread sealer or metal chips are
forced to the inside of the joints when connections are being tightened.
NOTE
Since the hydraulic motor is reversible, hose connections to motor fittings are
interchangeable.
STEP 2:
NOTE
STEP 3:
NOTE
Using a 1-7/16" wrench and a 1" wrench, tighten the hydraulic quick couplers onto
the hoses.
Danuser Hose Kits PN 206031 and 196025 do not include hydraulic quick
couplers. You must obtain the proper hydraulic quick couplers for your particular
vehicle.
Connect the quick couplers to the vehicle's auxiliary hydraulic outlets.
Ensure quick couplers are clean prior to connection.
WARNING
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is
running and may hold pressure after shutdown.
WARNING
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
STEP 4:
Test the vehicle to make sure you have adequate hose length and clearance between
attachment and vehicle throughout the full operating range of the vehicle's arm/
dipperstick.
NOTE
If the vehicle has a thumb attachment, it may need to be removed in the event that
it interferes with the mounting kit, drive unit, or hoses.
NOTE
Hose routing is the responsibility of the operator. Pinched, kinked, and/or stretched
hoses are not covered under the warranty.
STEP 5:
With the vehicle set at idle, engage the auxiliary hydraulics and verify output spindle
rotation. The output spindle should rotate clockwise when viewed from above.
STEP 6:
Check the hydraulic system for leaks.
WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
Proceed to Assembly & Installation: Auger, Extension, & Adapter section.
19
Assembly &
Installation
Bolt-on Bucket Mounting Kit
Recommended Tools
• 9/16" wrench
• 9/16" socket
• 1" wrench
NOTE
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
NOTE
•
•
3/4" wrench
3/4" socket
•
•
Drill
Torque wrench
•
•
17/32" drill bit
1-7/16" wrench
Consideration must be given to the installation location of the bolt-on bucket
mount kit. The drive unit should be able to swing during normal operation without
interference from the bucket. The bucket must be constructed with sufficient
strength to safely handle the loads generated during drilling. Position the drive
unit to allow space for the hydraulic hose connections and routing of hoses.
Hardware to attach the mount assembly is not included in the kit.
You will need the following:
• 4 bolts (1/2" dia., Gr. 5 or greater) • 4 lock washers (1/2") •
4 nuts (1/2")
STEP 1:
Using a drill and 17/32" drill bit, drill four holes in the left or right outside vertical
surface of the loader bucket to accommodate bucket mount assembly (1).
STEP 2:
Using a 3/4" wrench and torque wrench with 3/4" socket, bolt bucket mount
assembly (1) to the bucket.
1
CAUTION
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
STEP 3:
STEP 4:
STEP 5:
NOTE
NOTE
STEP 6:
NOTE
20
Attach knuckle assembly (2) to the drive
unit (3) using pin (4). Secure pin (4)
with lock pin (5).
1
Attach knuckle assembly/drive unit to
mount assembly (1) using pin (6). Using
a 9/16" wrench and torque wrench with
9/16" socket, secure pin (6) with bolt (7)
and nut (8).
6
8
7
2
If you purchased Danuser Hose Kits PN
196025 or 196027, install by using a
7/8" wrench and a 1" wrench to tighten
the hose connections onto the 45°
adapters on the drive unit.
All hoses and fittings used to connect the
earth auger should be thoroughly cleaned
before use. Care should be taken to see
that no thread sealer or metal chips are
forced to the inside of the joints when
connections are being tightened.
5
4
3
Since the hydraulic motor is reversible, hose connections to motor fittings are
interchangeable.
Using a 1-7/16" wrench and a 1" wrench, tighten the hydraulic quick couplers onto
the hoses.
Danuser Hose Kit PN 196025 does not include hydraulic quick couplers. You
must obtain the proper hydraulic quick couplers for your particular vehicle.
Assembly &
Installation
STEP 7:
NOTE
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
Ensure quick couplers are clean prior to connection.
WARNING
(continued)
WARNING
Connect the quick couplers to the vehicle's auxiliary hydraulic outlets.
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is
running and may hold pressure after shutdown.
STEP 8:
NOTE
STEP 9:
Test the vehicle to make sure you have adequate hose length throughout the full
operating range of the vehicle's loader arms. Adjust the position of the hoses as
necessary to avoid pinching, kinking, or stretching.
Hose routing is the responsibility of the operator. Pinched, kinked, and/or
stretched hoses are not covered under the warranty.
With the vehicle set at idle, engage the auxiliary hydraulics and verify output spindle
rotation. The output spindle should rotate clockwise when viewed from above.
STEP 10: Check the hydraulic system for leaks.
WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
Proceed to Assembly & Installation: Auger, Extension, & Adapter section.
Assembly &
Installation
Auger, Extension, &
Adapter
WARNING
Recommended Tools
• 1-1/8" wrench (2, for PN 10038 Retaining
Bolt and PN 10041 Nut)
• 15/16" wrench (2, for 2" round adapter with
5/8" bolt hole)
•
•
1-5/16" wrench (2, for 2-9/16" round
adapter with 7/8" bolt hole)
3/4" wrench (2, for 2" round or 2-9/16"
round adapters with 1/2" bolt hole)
STEP 1:
If using an extension or adapter with an auger, grease the inside of the extension or
adapter collar, and attach the extension or adapter to the drive unit using PN 10038
Retaining Bolt and PN 10041 Nut included with the drive unit.
STEP 2:
Grease the inside of the auger collar and attach the auger using PN 10038
Retaining Bolt and PN 10041 Nut included with the drive unit, or the bolt and nut
included with your auger.
Keep hands, feet, hair,
jewelry, and clothing
away from all moving
and/or rotating parts.
WARNING
Never replace the auger retaining bolt with anything other
than the specified length bolt in this manual. A longer,
or protruding, fastener is more likely to grab clothing or
gloves, which can result in serious injury or death.
NOTE
Each time an auger, adapter, or extension is attached, the inside of the collar should
be coated with grease.
21
Operation
DANGER
Contact with underground gas lines or electrical cables may
result in serious injury or death from explosion or electrical
shock. Before operating, call 811 or the local number to
locate underground utilities. Do not dig near underground
utility lines.
DANGER
This earth auger is
designed for one-man
operation from the
vehicle seat. It is the
responsibility of the
operator to see that no
one is within twenty-five
feet (25') of the earth
auger when it is started
or in use. Do not operate
the earth auger with
another person near or
in contact with any part
of the drive unit or auger.
Serious personal injury
or death may result if any
attempt is made to assist
drilling operation by
hand.
WARNING
Before operating, check clearances between vehicle and
auger, as well as operator and auger, across the vehicle's
full operating range to ensure auger does not contact
vehicle or operator.
WARNING
For mounts including a cradle, keep earth auger drive unit
in cradle when not drilling. To reduce the risk of personal
injury, never transport with the drive unit out of the cradle or
while the auger is rotating.
WARNING
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
WARNING
Safe operation of
equipment requires the
operator's full attention.
Avoid distractions such
as radio headphones,
cell phones, etc. while
operating.
DANGER
Do not allow riders on the
equipment at any time.
There is no safe place for
any riders.
22
Before you operate the earth auger, check over all pins, bolts,
and connections to be sure all are securely in place. Make
sure the earth auger is securely latched to the vehicle.
STEP 1:
Contact local utility companies to make certain there are no buried gas lines,
electrical cables, etc., in the work area. Clear area of objects that could wrap around the auger or might be thrown. Check for ditches, stumps, holes, or other
obstacles that could cause the vehicle to roll.
STEP 2:
Lay out and mark where you want to drill your holes.
STEP 3:
Lower the auger point slowly to the ground with the auger not powered.
NOTE
For mounts including a cradle, the drive unit should not come into contact with the
cradle during drilling maneuvers. While drilling, maintain the quick attach plate in
a position as close to horizontal as possible. If cradle does come into contact with
drive unit, refer to Assembly & Installation section to adjust carry angle.
STEP 4:
With the auger point lowered to the ground and before actuating the auger, move
the vehicle slowly left, right, forward, or backward as needed until the auger appears vertical to the ground.
STEP 5:
Engage the auxiliary hydraulics to start the auger’s rotation in the clockwise
direction and increase the speed as required so dirt is conveyed from the hole.
NOTE
The hydraulic actuation lever connected to the earth auger will have three
positions: clockwise rotation, stop (neutral), and counter-clockwise rotation.
The clockwise and counter-clockwise positions may be changed by switching
the hose connections.
DANGER
Never position the auger point by hand or with any tool
when the vehicle is running. Never position the auger point
by putting your hands on the auger or the drive unit.
Operation
STEP 6:
The hydraulic flow rate and pressure should not exceed the earth auger's specified
maximums. The hydraulic minimums must be met to deliver satisfactory
performance. Use only enough down pressure to assure positive penetration of the auger into the ground. Reduce down pressure if auger rotation slows down drastically or stalls. Excessive down pressure will cause the auger to
frequently stall. Refer to Hydraulic Requirements section for filtration, pressure,
and flow rate specifications.
NOTE
If you have difficulty penetrating hard ground, refer to the Troubleshooting section.
STEP 7:
When the auger has been lowered about 24" into the ground, raise the auger
almost out of the hole to clear the dirt, then drill deeper and raise the auger again.
Repeat this procedure until the desired hole depth is reached.
(continued)
NOTE
STEP 8:
When the auger has reached the full depth required, allow the auger to dwell
momentarily at this depth at a slower speed to assist in cleaning out the hole.
STEP 9:
Deactivate the earth auger, and raise it from the hole.
NOTE
DANGER
To prevent injury, keep an
area of at least
twenty-five feet (25’)
around the auger clear of
bystanders and all other
people.
For “heavy” soil conditions, allow the auger to turn at slow speed while raising it
to the top of the hole.
STEP 10: Move away from the hole, then remove loose dirt from the auger by momentarily
actuating the earth auger and spinning it at a faster speed than used for drilling. To
remove clay or other stubborn soil, actuate in a forward-stop, forward-stop manner.
NOTE
Do not actuate the earth auger in a forward-reverse manner, as damage may result.
STEP 11: If necessary, repeat STEPS 8 - 10 to obtain a cleaner hole.
NOTE
DANGER
Do not shovel dirt away
from a rotating auger, as
the shovel can be caught
and thrown by the auger.
The earth auger should be raised and lowered by changing the elevation and not
the tilt of the quick attach plate.
NOTE
In some soil conditions, or when excessive down pressure is applied, the auger may
screw itself into the ground and become stuck, causing the earth auger to stall. Do
not attempt to pull the auger out of the ground. Instead, reverse the auger rotation
(counter-clockwise), and slowly raise the auger. Once unstuck, continue operation.
If the auger becomes lodged under rocks, roots, or other large obstructions, do not
attempt to pull the auger out of the ground. If this happens, reverse the auger
rotation (counter-clockwise), and slowly raise the auger. Once unstuck, continue
operation.
STEP 12: Deactivate the auger and place the drive unit in the cradle when moving between holes.
NOTE
Frequently check the condition of the auger teeth and point, and replace them
when wear is detected. Always keep spare parts on hand for replacements to avoid
damage to the auger head and auger flighting.
23
Removal &
Storage
DANGER
Never allow anyone under
the attachment at any
time.
Before storage, the earth auger should be thoroughly cleaned, washing off all dirt and grime.
Make sure the hydraulic system is properly sealed against contaminants entering the unit.
Always store the earth auger in a dry, covered location.
STEP 1:
Lower the earth auger onto a flat, level surface in an area where children do not
play.
STEP 2:
Disconnect the hydraulic hoses from the vehicle's auxiliary hydraulics.
WARNING
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
CAUTION
Because of the weight of
some components, and
because some
components are difficult
to balance, two people
are required for safe
assembly and installation
of this equipment.
24
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is running
and may hold pressure after shutdown.
NOTE
Connect the quick couplers together to prevent contaminants from entering the
drive unit's hydraulic system.
STEP 3:
Follow your vehicle operator's manual for removing an attachment. Securely
block and support the attachment.
STEP 4:
Tighten any loose nuts, bolts, and hydraulic components.
STEP 5:
Replace any damaged or missing safety signs.
Troubleshooting
Problem
Possible Cause
Lacks drilling power
Slow auger speed
Auger will not drill
Drive unit contacting cradle
Gear oil leaks
Hydraulic oil leaks
Vehicle hydraulic
oil overheating
Hydraulic hose failure
Solution
Low system pressure (PSI)
Check with pressure gauge. If low, investigate the cause.
Low flow (GPM)
Check with flow meter. If low, investigate cause.
Fittings or connections are too small or
incompatible
Replace with proper fittings.
Hydraulic hose pinched or kinked
Fix pinched or kinked hose. Refer to Assembly &
Installation.
Dirty oil or filter
Change oil and filter according to vehicle
manufacturer's recommendation.
Hydraulic motor worn or damaged
See your dealer for repairs.
Worn teeth or point
Replace teeth or point. Refer to Accessories.
Ground too hard and dry
Replace dirt teeth and point with hardfaced or carbide
teeth and point. Refer to Accessories.
Cradle not installed in proper position
Refer to Assembly & Installation to adjust carry angle.
Output seal worn or damaged
Replace output seal. Refer to Parts: Drive Unit.
Motor seals worn or damaged, causing
hydraulic oil to leak into gearbox
See your dealer for repairs.
Fittings loose or damaged
Tighten or replace fittings
Hydraulic hose loose or damaged
Tighten or replace hydraulic hose
Hydraulic motor seals worn or damaged
See your dealer for repairs.
Low quantity of hydraulic oil
Add hydraulic oil to vehicle.
Improper hydraulic oil
Replace with proper hydraulic oil.
Dirty hydraulic oil or filter
Change oil and filter according to vehicle
manufacturer's recommendation.
Improper hose size
Check hose diameter and length requirements
Hydraulic relief pressure setting too high
Adjust vehicle hydraulic relief pressure setting to
within drive unit specifications.
Hoses worn or damaged
Replace hoses.
Hose rating too low for hydraulic system
pressure
Replace with hoses with working pressure rated
higher than vehicle hydraulic pressure.
Hoses pinched, kinked, or stretched
Refer to Assembly & Installation.
For additional assistance, please call your dealer or contact Danuser direct:
Tel: (573) 642-2246
Fax: (573) 642-2240
E-mail: [email protected]
25
Maintenance &
Lubrication
DANGER
Never allow anyone under
the attachment at any
time.
WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, and gloves
are recommended during
assembly, installation,
operation, maintenance,
service, removal, or
movement of the earth
auger. Do not allow long
hair, loose fitting
clothing, or jewelry to be
around moving and/or
rotating parts.
Proper servicing and maintenance are key to the long life of any attachment. Careful
inspection and routine maintenance helps avoid costly downtime and repair. Do not use the
earth auger with any damaged parts.
WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
WARNING
Do not modify the attachment. Modifications may weaken
the integrity of the attachment and may impair the safety,
function, life, and performance of the earth auger.
CAUTION
When making repairs or servicing the earth auger, use
only parts that meet original equipment manufacturer's
standards and requirements.
Maintenance
30°
Oil level
26
Inspect the attachment for any damage, worn parts, or
cracked welds. Repair or replace as necessary.
Check for damaged or missing safety signs. Replace as
necessary.
Coat the inside diameter of the auger or extension collar
with grease.
Check all fasteners. Ensure they are tight and secure.
(Refer to Torque Values Chart.) Replace as necessary.
Check all hydraulic components for leaks or wear.
Repair or replace as necessary.
Check planetary gear oil level to assure proper
lubrication is maintained. Check by removing the front
fill plug - with the drive unit angled approximately 30°
from vertical.
Check for clean hydraulic oil. At all times, keep dirt and
other contaminants from entering the hydraulic
system during connecting and disconnecting the
hydraulic system. Always use dust caps and plugs on all
quick disconnects when not in use.
Change planetary gear reduction oil after first 500 hours
of operation or 6 months, then every 2,000 hours or 12
months, whichever comes first. Use heavy duty extreme
pressure lubricant API-GL-5 85W-140 for filling the
planetary gear reduction. Approximate oil capacity is
.90 quarts (.85 liters).
Interval
Before each use
Before each use
Each time an auger or extension
is attached
Daily
Daily
Daily
Daily
After 1st 500 hours, then every
2,000 hours or yearly
Torque Values
Chart
Torque Values Chart
Bolt Head Identification
Bolt Size
(inches)
Grade 2
Grade 5
Grade 8
Bolt Head Identification
5.8
8.8
10.9
8.8
12.9
10.9
12.9
ASTM A574
Bolt Size
(Metric)
Class 5.8
mm x pitch
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
4
3
6
5
9
7
11
8
in tpi
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
1/4” 20
7.4
5.6
11
8
16
12
19
14
M5 x 0.8
Class 8.8
Class 10.9
Class 12.9
1/4” 28
8.5
6
13
10
18
14
22
16
M6 x 1
7
5
11
8
15
11
18
13
5/16” 18
15
11
24
17
33
25
39
29
M8 x 1.25
17
12
26
19
36
27
42
31
5/16” 24
17
13
26
19
37
27
43
32
M8 x 1
18
13
28
21
39
29
46
34
3/8” 16
27
20
42
31
59
44
69
51
M10 x 1.5
33
24
52
39
72
53
84
62
3/8” 24
31
22
47
35
67
49
79
58
M10 x 0.75
39
29
61
45
85
62
98
72
7/16” 14
43
32
67
49
95
70
110
81
M12 x 1.75
58
42
91
67
125
93
148
109
7/16” 20
49
36
75
55
105
78
123
91
M12 x 1.5
60
44
95
70
130
97
153
113
1/2” 13
66
49
105
76
145
105
168
124
M12 x 1
90
66
105
77
145
105
167
123
1/2” 20
75
55
115
85
165
120
190
140
M14 x 2
92
68
145
105
200
150
235
173
9/16” 12
95
70
150
110
210
155
235
173
M14 x 1.5
99
73
155
115
215
160
254
187
9/16” 18
105
79
165
120
235
170
262
193
M16 x 2
145
105
225
165
315
230
365
269
5/8” 11
130
97
205
150
285
210
323
238
M16 x 1.5
155
115
240
180
335
245
388
286
5/8” 18
150
110
230
170
325
240
366
270
M18 x 2.5
195
145
310
230
405
300
504
372
3/4” 10
235
170
360
265
510
375
574
423
M18 x 1.5
220
165
350
260
485
355
561
414
3/4” 16
260
190
405
295
570
420
640
472
M20 x 2.5
280
205
440
325
610
450
712
525
7/8” 9
225
165
585
430
820
605
925
682
M20 x 1.5
310
230
650
480
900
665
1052
776
7/8” 14
250
185
640
475
905
670
1020
752
M24 x 3
480
355
760
560
1050
780
1231
908
1” 8
340
250
875
645
1230
910
1386
1022
M24 x 2
525
390
830
610
1150
845
1337
986
1” 12
370
275
955
705
1350
995
1555
1147
M30 x 3.5
960
705
1510
1120
2100
1550
2447
1805
1-1/8” 7
480
355
1080
795
1750
1290
1971
1454
M30 x 2
1060
785
1680
1240
2320
1710
2706
1996
1-1/8” 12
540
395
1210
890
1960
1440
2202
1624
M36 x 3.5
1730
1270
2650
1950
3660
2700
4272
3151
1-1/4” 7
680
500
1520
1120
2460
1820
2771
2044
M36 x 2
1880
1380
2960
2190
4100
3220
5095
3758
1-1/4” 12
750
555
1680
1240
2730
2010
3068
2263
1-3/8” 6
890
655
1990
1470
3230
2380
3638
2683
1-3/8” 12
1010
745
2270
1670
3680
2710
4143
3056
1-1/2” 6
1180
870
2640
1950
4290
3160
4823
3557
1-1/2” 12
1330
980
2970
2190
4820
3560
5426
4002
KEY:
in tpi = nominal thread diameter in inches threads per inch
Nm = Newton-meter
ft.-lb. = foot pounds
mm x pitch = nominal thread diameter in millimeters by thread pitch
Torque tolerance +0%, -15% of torque values. Unless otherwise specified, use torque values listed above.
27
WARNING
Parts
Drive Unit
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
18
5
17
16
2
15
14
6
3
13
1
12
4
11
8
9
10
7
28
Parts
(continued)
REF. NO.
1
PART NO. DESCRIPTION
4
5
6
7
8
180405
180406
180407
180408
180409SEP615
180409SEP1020
180409SEP1530
180409SEP2035
10184
10185
10186
10964
10954
10955
20300
10197
10482
196009
10038
9
10
11
12
13
10041
20305
20312
20034
186071
14
15
16
17
18
20191
10484
10045
180425
196018
2
3
Drive Unit
Drive Unit
Drive Unit
Drive Unit
Housing Assembly (Includes EP615 Decals
& Safety Signs)
Housing Assembly (Includes EP1020
Decals & Safety Signs)
Housing Assembly (Includes EP1530
Decals & Safety Signs)
Housing Assembly (Includes EP2035
Decals & Safety Signs)
Hydraulic Motor
Hydraulic Motor
Hydraulic Motor
Hydraulic Motor
Hydraulic Motor Seal Kit (Not Pictured)
Hydraulic Motor Seal Kit (Not Pictured)
Planetary Gearbox (2" Hex)
Nut (7/16" 14)
Socket Head Bolt (M12 x 1.75 x 35mm)
Socket Head Bolt (7/16" 14 x 1-3/4")
Special Retaining Bolt
(3/4" 10 x 4", Gr. 8, 3/4" of thread)
Nut (3/4" 10)
Output Spindle (2" Hex)
Output Spindle Seal
Adapter, 90° (#10 ORB M to #8 JIC M)
Hydraulic Hose (Motor Adapter to External
Adapter, 9-1/8" length)
Nut (7/8" 14)
Adapter, 45° (#10 JIC F to #10 JIC M)
Adapter Thread Protector Cap
Pin (1-1/4" x 9-1/2")
Lock Pin
QTY. MODELS
1
1
1
1
1
EP615
EP1020
EP1530
EP2035
EP615
EP1020
EP1530
EP2035
1
1
1
1
1
8
4
8
1
EP615
EP1020
EP1530
EP2035
EP615, EP1020, EP1530
EP2035
All Models
All Models
All Models
All Models
All Models
1
1
1
2
2
All Models
All Models
All Models
All Models
All Models
2
2
2
1
1
All Models
All Models
All Models
All Models
All Models
29
WARNING
Parts
Skid-Steer Quick Attach Center & Offset
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
2
4
3
5
17
6
13
8
1
12
7
11
14
15
16
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
30
10
9
PART NO. DESCRIPTION
180415
12251
12247
1180
12259
10412
10267
10268
190122
190123
190124
170607
1600
180422
196020
21316
196012
Skid-Steer Quick Attach Plate Assembly
1/2" Hydraulic Hose Clamp Kit (Includes Hardware)
Hydraulic Hose Spring
Bolt (3/8" 16 x 1")
Washer (13/32" x 1-1/2")
Toplock Nut (3/8" 16)
Washer (3/4")
Lock Nut (3/4" 10)
Left Cradle Arm
Right Cradle Arm
Center Cradle Plate
Knuckle Assembly
Klik Pin
Pin Assembly
Carriage Bolt (3/8" 16 x 1-1/4", Gr. 5)
Nut (3/8" 16)
Bolt (3/4" 10 x 2", Gr. 8)
QTY.
1
1
1
1
2
1
8
4
1
1
1
1
1
1
4
4
4
WARNING
Parts
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
Euro/Global Quick Attach
- Offset
2
4
3
5
6
17
13
1
14
7
15
8
11
16
10
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
12
9
PART NO. DESCRIPTION
190052
12251
12247
1180
12259
10412
10267
10268
190122
190123
190124
170607
1600
180422
196020
21316
196012
Euro/Global Quick Attach Plate Assembly
1/2" Hydraulic Hose Clamp Kit (Includes Hardware)
Hydraulic Hose Spring
Bolt (3/8" 16 x 1")
Washer (13/32" x 1-1/2")
Toplock Nut (3/8" 16)
Washer (3/4")
Lock Nut (3/4" 10)
Left Cradle Arm
Right Cradle Arm
Center Cradle Plate
Knuckle Assembly
Klik Pin
Pin Assembly
Carriage Bolt (3/8" 16 x 1-1/4", Gr. 5)
Nut (3/8" 16)
Bolt (3/4" 10 x 2", Gr. 8)
QTY.
1
1
1
1
2
1
8
4
1
1
1
1
1
1
4
4
4
31
WARNING
Parts
John Deere 200-500 Series
Quick Attach - Offset
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
2
4
3
5
17
6
1
13
7
8
14
11
16
15
10
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
32
12
9
PART NO. DESCRIPTION
190053
12251
12247
1180
12259
10412
10267
10268
190122
190123
190124
170607
1600
180422
196020
21316
196012
John Deere 200-500 Series Quick Attach Plate Assembly
1/2" Hydraulic Hose Clamp Kit (Includes Hardware)
Hydraulic Hose Spring
Bolt (3/8" 16 x 1")
Washer (13/32" x 1-1/2")
Toplock Nut (3/8" 16)
Washer (3/4")
Lock Nut (3/4" 10)
Left Cradle Arm
Right Cradle Arm
Center Cradle Plate
Knuckle Assembly
Klik Pin
Pin Assembly
Carriage Bolt (3/8" 16 x 1-1/4", Gr. 5)
Nut (3/8" 16)
Bolt (3/4" 10 x 2", Gr. 8)
QTY.
1
1
1
1
2
1
8
4
1
1
1
1
1
1
4
4
4
WARNING
Parts
Mini-Skid-Steer
Quick Attach
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
13
2
12
14
3
8
4
1
7
5
9
6
17
15
10
11
16
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO. DESCRIPTION
200185
200207
12251
12247
1180
12259
10412
10267
10268
200189
200190
190124
170607
1600
180422
196020
21316
196012
Mini-Skid-Steer Quick Attach Plate Assembly
Bobcat MT Quick Attach Plate Assembly (Not Pictured)
1/2" Hydraulic Hose Clamp Kit (Includes Hardware)
Hydraulic Hose Spring
Bolt (3/8" 16 x 1")
Washer (13/32" x 1-1/2")
Toplock Nut (3/8" 16)
Washer (3/4")
Lock Nut (3/4" 10)
Left Cradle Arm
Right Cradle Arm
Center Cradle Plate
Knuckle Assembly
Klik Pin
Pin Assembly
Carriage Bolt (3/8" 16 x 1-1/4", Gr. 5)
Nut (3/8" 16)
Bolt (3/4" 10 x 2", Gr. 8)
QTY.
1
1
1
1
2
1
8
4
1
1
1
1
1
1
4
4
4
33
WARNING
Parts
Backhoe & Excavator
Quick Attach Mounting Kit
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
11
10
3
12
1
4
8
7
2
5
6
9
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
34
PART NO. DESCRIPTION
----196012
10267
10268
190122
190123
190124
196020
21316
172015
1600
180422
Quick Attach Mounting Kit
Bolt (3/4" 10 x 2", Gr. 8)
Washer (3/4")
Lock Nut (3/4" 10)
Left Cradle Arm
Right Cradle Arm
Center Cradle Plate
Carriage Bolt (3/8" 16 x 1-1/4", Gr. 5)
Nut (3/8" 16)
Knuckle Assembly
Klik Pin
Pin Assembly
QTY.
1
4
8
4
1
1
1
4
4
1
1
1
WARNING
Parts
Backhoe & Excavator
Pin-on Mounting Kit
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
4
1
3
REF. NO. PART NO. DESCRIPTION
1
2
3
4
----180427
10220
6196
QTY.
Ear Assembly
Knuckle Assembly
U-bolt (1/2" 13)
Locknut (1/2" 13)
2
1
4
8
2
Parts
1
Bolt-on Bucket Mounting Kit
4
3
5
2
REF. NO. PART NO. DESCRIPTION
1
2
3
4
5
9591B
172015
9595
3041
2805
Bucket Mount Assembly
Knuckle Assembly
Pin (1-1/4" x 6")
Bolt (3/8" 16 x 3-1/2", Gr. 8)
Self-locking Nut (3/8" 16)
QTY.
1
1
1
1
1
35
Augers &
Accessories
WARNING
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
"FAB" AUGERS - Light-Duty
Light to Moderate Ground Conditions
4′ LENGTH
DIA.
NO. OF TEETH
PART NO.
4″
0
10600
6″
2
10603
8″
2
10606
9″
3
10609
10″
3
10612
12″
4
10615
15″
5
10618
16″
5
10621
18″
6
10624
20″
6
10627
24″
8
10630
30″
9
10633
36″
11
10636
"CAST" AUGERS - Heavy-Duty
Difficult Ground Conditions
4′ LENGTH
36
DIA.
NO. OF TEETH
PART NO.
6″
2
10657
8″
4
10660
9″
4
10663
10″
4
10666
12″
4
10669
15″
6
10672
16″
6
10675
18″
6
10678
20″
6
10681
24″
8
10684
30″
10
10687
36″
12
10690
Please call Danuser for 3′, 5′, or 6′ requests.
Augers &
Accessories
WARNING
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
"TREE" AUGERS
4′ LENGTH
DIA.
NO. OF TEETH
PART NO.
18″-9″
7
10639
24″-12″
10
10642
30″-15″
11
10645
36″-18″
13
10648
AUGER COLLAR
DESCRIPTION
PART NO.
2″ Hex
10328
AUGER TEETH & HARDWARE
Wisdom tooth
Gage tooth
DESCRIPTION PART NO. DESCRIPTION PART NO.
Dirt
Hardfaced
10340D
10340HF
Dirt
Hardfaced
Carbide
10337D
10337HF
10337C
Chisel tooth
Teeth bolt & nut
DESCRIPTION PART NO.
DESCRIPTION PART NO.
Dirt
Hardfaced
Carbide
Carriage Bolt
Nut
10342D
10342HF
10342C
10410
10411
FISHTAIL POINTS
4" diameter augers
Other diameter augers
DESCRIPTION
PART NO.
DESCRIPTION
PART NO.
Dirt
Hardfaced
Chunky Carbide
Nut
Bolt
10333D
10333HF
10333C
10412
10416
Dirt
Hardfaced
Chunky Carbide
Nut
Bolt
10331D
10331HF
10331C
10412
10413
37
WARNING
Augers &
Accessories
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
"BULLET" ROCK AUGERS
Rock, Concrete, Asphalt,
and Frozen Ground
4′ LENGTH
DIA.
"BULLET" ROCK
DESCRIPTION
PART NO.
NO. OF TEETH PART NO.
4.5″
4
200152
Retaining Bolt
206047
6″
6
200155
Retaining Nut
10041
8″
8
200158
Retaining Lock Washer
823
9″
10
200161
200251
10″
10
200164
Pilot (6-Tooth, 6" dia.,
includes hardware)
12″
12
200167
200192
15″
14
200170
Pilot (4-Tooth, 8" dia. & up,
includes hardware)
Pilot Bolt
10123
18″
16
200173
Pilot Nut
7733
24″
30″
20
24
200176
200179
Tooth
200281
Tooth Holder
10760
36″
28
200182
Tooth Hammer & Puller
10766
WOBBLE AUGERS
4′ LENGTH
The Wobble Auger pushes through
dirt, sand, clay, asphalt, compacted
rock, and embedded rock. The
9″ Wobble Auger should be used
on a skid-steer with an Operating
Load or Rated Operating Capacity
of 2,250 lb. or greater, utilizing an
auger drive with 2,000 ft.-lb. of
torque or greater.
DIA.
NO. OF TEETH
PART NO.
4"
N/A
20600
6"
N/A
20603
9"
N/A
20606
AUGER EXTENSIONS
Fixed length
38
Variable length
LENGTH
PART NO.
LENGTH
PART NO.
12″
24″
10910
10911
12″
24″
---10900
48″
10912
48″
10901
72″
10913
72″
10902
Augers &
Accessories
WARNING
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
AUGER ADAPTERS
DRIVE UNIT
AUGER COLLAR
PART NO.
2″ Hex
to
2-9/16″ Rd.
10921
2″ Hex
to
2″ Rd.
10922
2″ Hex
to
2-9/16″ Rd.
*20211
2″ Hex
to
2″ Rd.
*20214
*Allows attachment of augers with 1/2" diameter bolt.
HOSES & HYDRAULIC ACCESSORIES
DESCRIPTION
Hose Holder
Spring Kit
1/2” flush-face
couplers (ISO
16028)
PART NO.
Cross Port Relief Valve
196035
1/2” Hose Holder Spring Kit
190172
1/2” Hose Kit, 108” with Couplers & Abrasion Sleeves
Includes 1/2” flush-face couplers (ISO 16028).
196027
1/2” Hose Kit, 108” with Abrasion Sleeves
Does not include couplers.
196025
Front-End Loader Hose Kit
1/2” hoses, 25’ long, with 1/2” flush-face couplers (ISO 16028) on one end to
connect to 196027 Hose Kit above (sold separately), and ISO 7241 Series A couplers
(compatible with ISO 5675 Pioneer couplers) on the opposite end to connect to tractor
rear remotes. Includes bolt-on/weld-on mounting bracket.
196056
1/2” Backhoe, Excavator, & Mini-Skid-Steer Hose Kit, 66” with Couplers &
Abrasion Sleeves
Includes 1/2" flush-face couplers (ISO 16028).
206032
1/2” Backhoe, Excavator, & Mini-Skid-Steer Hose Kit, 66” with Abrasion Sleeves
Does not include couplers.
206031
Male Coupler (1/2" flush-face, ISO 16028)
10048
Female Coupler (1/2" flush-face, ISO 16028)
10049
2" ROCK DRILL - Pilot Holes
3′ LENGTH
PYTHON WIRE WINDER
DESCRIPTION PART NO.
2″ Hex
170610
The Python Wire Winder is
designed to meet the needs
of farmers, ranchers, and
fencing professionals. The
Python connects onto a 2”
hex hydraulic auger drive unit
and can wind up to 6 miles of
smooth or 3/4 miles of barbed
wire into convenient rolls.
DIA.
NO. OF TEETH PART NO.
2"
N/A
10739
2" ROCK DRILL
DESCRIPTION PART NO.
Pilot
10745
39
Warranty
DANUSER
LIMITED WARRANTY
Model #
Serial #
Danuser Machine Company (“Danuser”) warrants its products, under normal use and maintenance, to be free from defects in
material and workmanship for period(s) specified below from the purchase date from an authorized Danuser Dealer. Start of the
warranty period is determined by purchase date given on your returned WARRANTY REGISTRATION FORM. Proof of purchase
may be required. This Limited Warranty is extended only to the original purchaser of Danuser products.
EP Drive Units - 5 Years
Mountings - 1 Year
Augers - 1 Year
Lifetime Warranty Covering EP Drive Unit Output Pull Out
Wear Items Not Covered Under Warranty - Hydraulic Hoses, Seals, Auger Teeth, and Auger Point
1.
During the applicable warranty period, Danuser, at its option, will repair or replace any part determined by Danuser to be
defective. Such repair or replacement shall take place at Danuser’s factory or a location designated by Danuser. Under no
circumstances shall Danuser be obligated for the cost of any repair or replacement by anyone other than Danuser without its
express written consent.
2.
Parts may not be returned without written authorization from Danuser.
3.
Some purchased components, including but not limited to hydraulic motors, planetary gears, and augers, are subject to the
inspection and warranty of the respective manufacturer. Thus, delays in a warranty determination can be expected while
Danuser awaits their decision.
4.
This warranty is void if any attempt is made to make field repairs to hydraulic motors or planetary gears. To qualify for
warranty inspection, the complete drive unit must be returned in its original “failed” condition.
5.
To make a claim under this warranty, first contact your authorized Danuser Dealer. The Danuser Dealer shall complete the
Warranty Claim Form and obtain written authorization from Danuser to return parts. All warranty claims must include
detailed information regarding make and model of vehicle on which the Danuser product was mounted, hours of use, description of events that led up to the failure, and any other information helpful in reviewing the warranty claim. All
warranty returns must be prepaid. Shipments arriving at our factory on a freight collect basis will be refused by our
receiving department. The freight charge will be credited if the parts are determined by Danuser to be defective, and the
associated freight costs in returning those parts will be prepaid by Danuser. NOTE: Hydraulic motors must arrive with all
ports sealed from dirt and moisture. If a motor arrives with open ports, the warranty is void and no inspection will be made.
6.
Products or parts thereof which, as determined by Danuser’s examination, show wear from normal use, have been
improperly operated, damaged by accident or negligence, field repaired, altered or modified are not considered defective in
material and workmanship and are not covered by this warranty. This warranty does not apply to parts subject to normal
wear ("Wear Items") or to damage caused by the failure to perform recommended maintenance or to replace worn parts.
This warranty shall not obligate Danuser to bear any cost of labor for field repair, replacement, testing, or adjustment nor for
damage caused by accident, abuse, misuse, or environmental elements.
7.
Any parts or labor required to repair or replace parts not covered under this warranty will be charged to the customer. Parts
repaired or replaced by Danuser are then covered by this warranty only for the remainder of the original warranty as if such
parts were original parts.
8.
Danuser reserves the right to change its specifications and designs at any time.
This warranty is exclusive and in lieu of all other express warranties, if any, including the implied warranties of merchantability
and fitness for a particular purpose. It shall not extend beyond the duration of the expressed warranty provided herein and the
remedy for violations of any implied warranty shall be limited to repair or replacement of the defective part pursuant to the terms
contained herein. No employee, dealer, salesman, or representative is authorized to change this warranty in any way or grant any
other warranty. Danuser shall not be liable for any consequential, incidental, or punitive damages, losses, or expenses, including
those resulting from or caused by any defects.
Danuser Machine Company
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel:
(573) 642-2246
Fax:
(573) 642-2240
E-mail: [email protected]
Website:
www.danuser.com
PD 5022
">