Dlink DCM-604 User`s manual

DCM-604

Cable Modem EMTA Gateway

P a c k e t t C a b l e 1 .

5 a n d D O C S I S 2 .

0 C e r t i f i e d

4 P o r r t t s E t t h e r n e t t C a b l l e R o u t t e r w i i t t h 2 P o r t t s V o i i c e

User’s Manual

Version 0.9

FCC Statement

This device complies with Class B Part 15 of the FCC Rules. The device generates, uses and can radiate radio frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communication. Only Coaxial cables are to be used with this device in order to ensure compliance with FCC emissions limits. Accessories connected to this device by the user must comply with FCC Class B limits. The manufacturer is not responsible for any interference which results from use of improper cables, or which results from unauthorized changes or modifications to the device.

"A Minimum 26 AWG Line Core should be used for connection to the cable modem"

Trademarks

All trademarks are the property of their respective owners.

Table of Contents

1. INTRODUCTION................................................................................................1

1.1 S YSTEM R EQUIREMENTS .................................................................................1

1.2 U

NPACKING AND

I

NSPECTION

.........................................................................1

1.3 S

AFETY

P

RECAUTIONS

....................................................................................1

2. HARDWARE OVERVIEW................................................................................2

2.1 F RONT P ANEL AND LED S ...............................................................................2

3. ETHERNET INSTALLATION..........................................................................4

4. USB DRIVER INSTALLATION .......................................................................5

4.1 W INDOWS XP .................................................................................................5

4.2 W

INDOWS

2003 ..............................................................................................7

4.3 W

INDOWS

V

ISTA

............................................................................................9

5. WEB MANAGEMENT .....................................................................................11

5.1 E

NTER

M

ODEM

'

S

IP

ADDRESS

.......................................................................11

5.2 S

TATUS

.........................................................................................................12

5.2.1 Software Status.....................................................................................12

5.2.2 Security ................................................................................................12

5.3 B

ASIC

............................................................................................................13

5.3.1 Setup.....................................................................................................13

5.3.2 DHCP...................................................................................................13

5.3.3 Backup..................................................................................................14

5.4 A

DVANCED

...................................................................................................14

5.4.1 Options .................................................................................................15

5.4.2 IP Filtering...........................................................................................16

5.4.3 Port Filtering .......................................................................................16

5.4.4 Forwarding ..........................................................................................17

5.4.5 Port Triggers........................................................................................17

5.4.6 DMZ Host.............................................................................................18

5.5 F IREWALL .....................................................................................................19

5.5.1 Web Filter ............................................................................................19

5.5.2 Local Log .............................................................................................19

5.5.3 Remote Log ..........................................................................................20

5.6 P ARENTAL C ONTROL ....................................................................................21

5.7 W

IRELESS

.......................................................................................................1

5.7.1 Radio ......................................................................................................1

5.7.2 Primary Network....................................................................................2

5.7.3 Advanced................................................................................................2

5.7.4 Access Control .......................................................................................3

5.7.5 WMM......................................................................................................4

5.8 MTA...............................................................................................................5

5.8.1 Status......................................................................................................5

5.9 H

ARD

R

ESET

...................................................................................................6

DCM-604 Cable Modem EMTA Gateway User’s Manual

1. Introduction

The DCM-604 is a Voice over IP Wireless Residential Gateway integrated with Cable Modem which allows you implement your VoIP phone call directly through Cable Modem Broadband Network service with its built-in

PacketCable 1.5 and DOCSIS/EURODOCSIS 2.0 compliant specification.

And with the integration of 4 ports switch and IEEE 802.11g wireless functionality, the DCM-604 series could also be used as a Wireless Cable

Modem Residential Gateway in your home or small office. The ability to route data information into your broadband network could help you easily extend your local network via wire or wireless.

 IBM Compatible, Macintosh or other workstation supports TCP/IP protocol.



An Ethernet port supports 10Base-T/100Base-TX Ethernet connection or

USB-equipped PC.

 Subscribed to a Cable Television company for Cable Modem services.

1.2 Unpacking and Inspection

Included in the kit is the following:

 1 x EMTA DCM-604

 1 x RJ-45 CAT 5 Cable



1 x 15V/1.0A Power Supply Adaptor

 1 x CD-ROM containing USB Driver

 1 x 6P4C Telephone Cord

 1 x USB Cable

If any of above items lost or damaged, please contact your retailer or ISP for assistance.

For your protection, observe the following safety precautions when setting up and using your equipment. Failure to observe these precautions can result in serious personal injury and damage to your equipment.

 Make sure the voltages and frequency of the power outlet matches the electrical rating labels on the AC Adapter.

 Do not place any object on top of the device or force it into a confined space.

 Never push objects of any kind through openings in the casing. Dangerous voltages may be present. Conductive foreign objects could produce a short circuit that could cause fire, electrical shock, or damage to the equipment.

 Whenever there is danger of lightning, disconnect the power cable and the

Hybrid-Fiber Coax cable from the cable modem to prevent damage to the unit.

The use of an AC protection device will not completely protect the cable modem product from damage caused from the transmission across the Hybrid-Fiber

Coax network.

1


2.1 Front Panel and LEDs

There are fourteen Light-Emitting-Diodes (LEDs) located on the front panel top provide status information to the user.

LED NAME COLOR MODE STATUS

On

Power Green

Off

Connected with power

Power failure or disconnect

Blinking

Cable Green

On

On

Tx Green

Blinking

TFTP/DHCP in process

AIO Registered

Upstream channel acquired

Acquiring upstreaming channel

On

Rx Green

Blinking

Downstream channel acquired

Acquiring downstream channel

LAN 1 Green On

Off

Ethernet port 1 linked

Disconnected

LAN 2 Green On

Off


Disconnected

LAN 3 Green On

Off


Disconnected

LAN 4 Green On

Off


Disconnected

Blinking USB

USB Green

Voice

Green

Message On

Blinking

Off

Blinking

VoIP linked in calling

Line 1 is registered in the network

Line 1 is not registered in the network in calling

Line 2 is registered in the network

Off

Line 2 is not registered in the network

Blinking Transferring

Wifi Green

On WIFI Ready

2


Blinking

On

WPS Activating

WPS Connected

WPS Blue

Off No WPS Connection

2.2 Rear Panel and Hardware Connection

This chapter describes the proper steps for connecting your cable modem. Please be sure to follow the steps in the sequence outlined below. Failure to do so could result in improper operation or failure of your cable modem.

Step 5 Adjust the

Antenna

Step 2 Connecting to a Network Interface Card

Or Connecting to the USB port on your PC

Step 3 Connecting the

Telephone cord

Step 4 Connecting to the AC Adapter

Reset Button

Step 1 Connecting the Coaxial Cable

Step 1: Connect a cable by feeding the F-connector on the back of the cable modem. Ensure the center conductor of the 75 ohm coaxial cable is inserted directly into the center of the F-connector. Secure the coaxial cable by carefully threading the outer shell of the coaxial cable connector onto the F-connector in a clockwise direction until tight. Be careful not to over-tighten the connector or you may damage either the connector or the cable modem.

Step2: Connect the cable modem to an IEEE 802.3 10BaseT / 802.3u 100Base-TX

Network using a RJ-45 male-terminated Ethernet cable or an USB cable to the PC.

This cable modem equips with two Ethernet ports, you can connect two PCs to the cable modem at the same time if necessary.

Step 3: Connect the telephone sets to TEL1 and TEL2. Use RJ-11 telephone line to connect TEL1/TEL2 port on the cable modem and telephone socket on telephone.

Step 4: Connect the AC Adapter to the cable modem by inserting the barrel-shaped connector into the mating power connector on the back of the cable modem.

Exercise carefully to ensure the connectors are properly aligned prior to insertion and ensure the two connectors engage completely. The cable modem is shipped with an

AC adapter. Remember to use only power adapter that came with the cable modem.

Other power adapters might have voltages that are not correct for your particular cable modem. Using a power adapter with the wrong voltage can damage the cable modem.

Step 5: Adjust the antenna if necessary.

3


The LAN port you are using is auto-negotiating 10/100Mbps (Switch) Ethernet

Interface. You can use the Ethernet port to connect to the Internet with an

Ethernet network device such as NIC/Hub/Switch through RJ45.

Before you connect to and install the cable modem, please set the IP address to "Obtain an IP address automatically" as below and do ensure the TCP/IP protocol is installed on your system and configured correctly in your PC.

Following is an example of configuring the TCP/IP Protocol on Windows 98

Operating Systems:

1. Click Start SettingsControl Panel. Double click on the Network icon click Properties.

2. A list of installed network components appears. Look for an entry named

TCP/IP. This entry may be followed by an arrow and a description of the

NIC hardware device installed in the computer. If you don't see "TCP/IP" listed anywhere in the "The following network components are installed" box, click the Add button, choose Protocol, and click the Add button.

Select "Microsoft" as the manufacturer and then scroll down in the list on the right to find "TCP/IP". If you see "TCP/IP" listed, proceed to step 4.

3. Click the OK button. You will be prompted to insert the Windows 98 installation/upgrade CD.

4. Scroll down in the box until you find a line that says "TCP/IP -> " followed by the name of your Ethernet adapter. Click on Properties and choose

"Obtain an address automatically" which means that your PC has been configured to use DHCP (Dynamic Host Configuration Protocol).

5. Click OK.

Congratulations! You have successfully set up your cable modem.

4


4. USB Driver Installation

Using the USB port to connect to the Internet allows you to install the cable modem more quickly and easily than connecting to the Internet using the

Ethernet port, since you do not need to install a network interface card (NIC).

1. Connect USB cable from PC to cable modem.

2. Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic. Cable

Modem may reboot if you previously connect it through Ethernet port.

3. Windows will prompt new hardware found, insert the Driver CD into your

CD-ROM drive.

4. You may seed this window if you had update your Windows XP to

Service Pack 2. Select “Yes, this time only” and then click Next.

5. Select “Install the software automatically (Recommended)” and then click

Next.

5


6. Windows will locate the driver automatically. Please click Continue

Anyway to continue the installation process.

7. Windows shall find the location of USB driver and complete the installation. Click Finish.

6


1. Connect USB cable from PC to cable modem.

2. Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic. Cable


3. Windows will prompt new hardware found, insert the Driver CD into your

CD-ROM drive.

4. Select “Yes, this time only” and then click Next.

5. Select “Install the software automatically (Recommended)” and then click

Next.

7


6. Windows will locate the driver automatically. Please click Continue

Anyway to continue the installation process.

7. Windows shall find the location of USB driver and complete the installation. Click Finish.

8


1.

Connect USB cable from PC to cable modem.

2.

Connect RF cable and power on Cable Modem. Wait until it register, it will take about 40 seconds to 4 minutes depends on network traffic. Cable


3.

Windows will prompt new hardware found, insert the Driver CD into your

CD-ROM drive.

4.

Click “Locate and install driver software (recommended)” item

5.

Insert the Driver disk that came with your cable modem into your CD-

ROM drive. Windows Vista will automatically searched and found this driver.

9


6.

During the driver installation, your system may pop-up a dialogue as below window, just click “Install this driver software anyway”.

7. During the driver installation, your system may pop-up a dialogue as below window, just click “Install this driver software anyway”.

8. Click “Close” button to finish the driver installation.

10


For easy-changing the default setting or quick-checking diagnostics for troubleshooting, a Web-based GUI is built-in for your access.

5.1 Enter Modem's IP address

Use the following procedures to login to your DCM-604.

1. Open your web browser.

You may get an error message. This is normal. Continue on to the next step.

2. Type the default IP address of the DCM-604 (e.g. 192.168.0.1) and press

Enter.

3. The Log In page appears. Type the user name (admin) and your password (password) in the respective fields.

4. Click the Logout button to leave the application.

11


There are seven categories in this web management including Status, Basic,

Advanced and Firewall. The following sections describe their details.

5.2 Status

The Status page shows hardware and software information about the DCM-

604 that may be useful to your cable service provider.

The Software page shows how long the DCM-604 has operated since last being powered up, and some key information the DCM-604 received during the initialization process with your cable service provider.

(Pls change the screen capture. Pls use f/w 4k)

5.2.2 Security

This page allows the configuration of administration access privileges and the ability to restore the settings to factory defaults to the system and allows switching to router or bridge mode. If DCM-604 mode set as bridge, the "basic", "advance" and "firewall" tabs of webpage will be disabled. The DCM-604 home page will change to 192.168.100.1. And to access home page, need to set up connected device (PC) IP address as 192.168.100.xx. After changing the settings, click Apply, then the modem will reboot to take effect setting. And wait for DCM-604 boot up completes.

12


5.3 Basic

The Basic page contains the basic features of DCM-604 including Setup,

DHCP and Backup

5.3.1 Setup

This setup page allows configuring the basic features of the broadband gateway related to your ISP's connection.

5.3.2 DHCP

The DHCP page allows you to activate/deactivate the DHCP server function of the DCM-604, and, if the DHCP server is activated, to see DHCP leases it has provided.

13


With this function activated, your cable service provider’s DHCP server provides one IP address for the DCM-604, and the DCM-604’s DHCP server provides IP addresses, starting at the address you set in Starting Local

Address field, to your PCs. A DHCP server leases an IP address with an expiration time.

To set the maximum number of PCs to which the DCM-604 will issue IP addresses, enter it in the Number of CPEs box and then click Apply. (CPE is another term sometimes used for PC.)

The table on the bottom of this page shows the information of DHCP clients including the IP and MAC addresses of each PC. Since MAC addresses are unique and permanently fixed into hardware, you can identify any PC listed by its MAC address. The DCM-604 provides leases for 3600 seconds (default), and has an automatic renewal mechanism that will keep extending a lease as long as the associated PC remains active.

You can cancel an IP address lease by selecting it in the DHCP Client Lease

Info list and then clicking the Force Available button. If you do this, you may have to perform a DHCP Renew on that PC, so it can obtain a new lease.

5.3.3 Backup

This page allows you to save your current settings locally on your PC, or restore previously saved settings.

5.4 Advanced

The Advanced page allows you to enable/disable some advanced features of the DCM-604.

14


5.4.1 Options

The Options page allows you to enable/disable some advanced features supported by DCM-604.

Check the option you want to use and click Apply button to enable the function(s).



WAN Blocking: To prevent others on the WAN side from being able to ping your DCM-604. With WAN Blocking on, your DCM-604 will not respond to pings it receives, effectively “hiding” your gateway.

 IPSec Pass-through: To enable IPSec type packets to pass through between WAN and LAN.



PPTP Pass-through: To enable PPTP type packets to pass through between WAN and LAN.



Remote Config Management: To make the Web Management pages of your DCM-604 accessible from the WAN side. Page access is limited to only those who know the DCM-604 access password you set in the

Status--Security page.

When accessing the DCM-604 from a remote location, you must use

HTTP port 8080 and your IP address. This is the "WAN IP address" that appears at the Basic--Setup page. For example, if this IP address were

211.20.15.28, you would navigate to http:// 211.20.15.28:8080 to reach the DCM-604’s Web Management page from a remote location.



Multicast Enable: To enable multicast traffic to pass through between

WAN and LAN. You may need to enable this to see some types of broadcast streaming and content on the Internet, such as webcasting of a popular live event.

 UPnP Enable: UPnP (Universal Plug and Play) offers pervasive peer-topeer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP architecture leverages TCP/IP and the Web to enable seamless proximity networking in addition to control and data transfer among networked devices in the home, office, and everywhere in between.

15


The IP Filtering page enables you to enter the IP address ranges of PCs on your LAN that you don’t permit to have outbound access ability to the WAN.

These PCs can still communicate with each other on your LAN, but packets they originate to WAN addresses are blocked by the DCM-604.

To enable IP Filtering feature of DCM-604, check the Enable box and click

Apply button.

The Port Filtering page allows you to enter ranges of destination ports

(applications) that you don’t want your LAN PCs to send packets to. Any packets your LAN PCs send to these destination ports will be blocked. For example, you could block access to worldwide web browsing (HTTP port 80) but still allow email service (SMTP port 25 and POP3 port 110).

To enable port filtering, enter the Start port and End port for each range.

Then select its protocol form the drop-down list and check the Enable box, and click Apply button. To block only one port, set both Start and End ports the same.

16


5.4.4 Forwarding

For communications between LAN and WAN, the DCM-604 normally only allows you to originate an IP connection with a PC on the WAN; it will ignore attempts of the WAN PC to originate a connection onto your PC. This protects you from malicious attacks from outsiders. However, sometimes you may wish for anyone outside to be able to originate a connection to a particular PC on your LAN if the destination port (application) matches one you specify.

The Forwarding page allows you to specify up to 10 rules.

Using the Port Forwarding page, you can provide local services (web servers,

FTP servers, mail servers, etc) for people on the Internet or play Internet games. A table of commonly used port numbers is also provided.

The Port Triggers page allows you to configure dynamic triggers to specific devices on the LAN. This allows for special applications that require specific port numbers with bi-directional traffic to function properly. Applications such as video conferencing, voice, gaming, and some messaging program features may require these special settings.

17


Port Triggering is an elegant mechanism that does the forwarding for you, each time you play the game.

You can specify up to 10 port ranges on which to trigger.

The DMZ page allows you to configure a specific network device to be exposed or visible directly to the WAN (public Internet). Setting a host on your local network as demilitarized zone (DMZ) forwards any network traffic that is not redirected to another host via the port forwarding feature to the IP address of the host (PC). This designates one PC on your LAN that should be left accessible to all PCs from the WAN side for all ports. For example, if you locate a HTTP server on this machine, anyone will be able to access that

HTTP server by using your DCM-604’s IP address as the destination. This may be used when problem applications do not work with port triggers. The setting of “0” indicates NO DMZ PC.

18


5.5 Firewall

The DCM-604 provides built-in firewall functions, enabling you to protect the system against denial of service (DoS) attacks and other unwelcome or malicious accesses to your LAN.

This page allows certain Web-oriented cookies, java scripts, and pop-up windows to be blocked by the firewall. A list of "trusted computers" can also be defined that are not subject to any filters configured. Specific Firewall features can also be enabled. It is highly recommended that the Firewall is left enabled at all times for protection against Denial of Service attacks. Go to the Parental Control page to block internet access to specific sites.

The Local Log page allows you to configure the firewall event log reported via email alert, and these attack records are also visible in the table on the bottom of this page.

19


Specify the e-mail address and its SMTP of the administrator who needs to receive the notice of any attempted firewall violations. Type the addresses in standard Internet e-mail address format, for example, [email protected]. Then check the Enable box to enable the alert feature and click Apply button.

Click E-mail Log to immediately send the email log. Click Clear Log to clear the table of entries for a fresh start.

20


This page allows configuration of users. “White List Only” feature limits the user to visit only those sites specified in the Allowed Domain List in Parental

Control, Basic page of his/her content rule. Actually, this page helps you to identify whether or not the Websites are blocked to access.

5.6.2 Basic Setup

This page allows basic selections of rules which block certain Internet content and certain Web sites. When you change your Parental Control settings, you must click on the appropriate “Apply”, “Add” or “Remove” button for your new setting to take effect. If you refresh your browser’s display, you will see the currently active settings.

21


5.6.3 Time of Day Filter

This page allows configuration of time access policies to block all internet traffic to and from specific network devices based on time of day setting. And it helps to ensure that the target or connected computer cannot access the internet at all.

You can selecte Everyday or a day of the week by Enabling the check box and can change the Time to All Day or specific the start and end time by entering the time.

22


5.6.4 Local Log

This page displays Parental Control Local log reporting.

5.7 Wireless

5.7.1 Radio

1


5.7.3 Advanced

This page allows configuration of data rates and WiFi thresholds.

2


This page allows configuration of the Access Control to the AP as well as on the connected clients.

3


5.7.5 WMM

This page allows configuration of the Wi-Fi Multimedia QoS.

4


5.8 MTA

Section MTA has 5 sub-items, which indicate the status of MTA. These information can help you to understand the parameters of MTA operation.

5.8.1 Status

This page displays initialization status of the MTA.

5


To factory reset the DCM604, press and hold the reset button for at least 10sec

Reset Button

6

Dlink DCM-604 User`s manual

DCM-604

Cable Modem EMTA Gateway

User’s Manual

1. Introduction

2.2 Rear Panel and Hardware Connection

4. USB Driver Installation

Related manuals

D-Link

KA2CM604A1

CastleNet Technology

RK9-CBV3843Z4S

D-Link

DCM-604 Series

CastleNet Technology

RK9-CBV704W

CastleNet Technology

RK9-CBW560

SMC Networks

JI5-D3GN4

D-Link

DCM-200

Askey Computer Corp

H8NDWG855