Symbol PPT 2700 Pocket PC Quick Reference Guide

P
P
T
2
7
0
0
S
e
Pocket
PC
r
i
e
s
P P T
2 7 0 0
S e r i e s
 1999-2000 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve reliability,
function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Symbol products might
be used. An implied license only exists for equipment, circuits, and subsystems
contained in Symbol products.
Symbol is a registered trademark of Symbol Technologies, Inc. Other product names
mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Patents
This product is covered by one or more of the following U.S. and foreign Patents:
U.S. Patent No. 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750;
4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532;
4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183;
5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950;
5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088;
5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627;
5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498;
5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151;
5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139;
5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891;
5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441;
5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592;
5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531;
5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929;
5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043;
5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731;
5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812;
5,828,050; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989;
5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420;
5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,047,892;
6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,068,190; D305,885;
D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478;
D383,124; D391,250; D405,077; D406,581; D414,171; D414,172, D419,548;
D423,468; D424,035.
Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875;
1,955,269 (Japan).
European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/
03938; Italy 1,138,713.
rev. 06/00
Q u i c k
R e f e r e n c e
Introduction
Congratulations on your purchase of Symbol Technologies’ PPT
2700 Terminal! Its unique combination of features make this
product superior for use in a wide range of applications. These
features include:
•
•
•
•
•
•
Pocket size
Personal Information Management software
Microsoft® Windows® Pocket PC operating system
RF communication via Symbol’s Spectrum24 wireless
network or a wide area network (WAN) (CDPD and GSM)
Printing support
1 or 2-dimensional scanning capability.
About This Guide
This guide describes how to set up and use the terminal. The term
PPT 2700 refers to the batch 1D scanning terminal, the batch
PDF417 scanning terminal, and the Spectrum24 terminal. Specific
topics covered include:
• Parts of the PPT 2700 on page 2
• Installing Batteries on page 4
• Charging the Battery on page 5
• Starting the PPT 2700 on page 8
• Aligning the Screen on page 8
• Using the PPT 2700 on page 9
• Using the Stylus on page 10
• Today Screen on page 11
• Navigation Bar and Command Bar on page 12
• Input Methods on page 13
• Scanning with the PPT 2700 on page 15
• Resetting Your PPT 2700 Terminal on page 17
• Maintaining the PPT 2700 on page 19
• Troubleshooting on page 19.
The PPT 2700 Product Reference Guide (p/n 70-37806-xx),
available from your Reseller or from Symbol Technologies, details
the applications available for the PPT 2700.
1
P P T
2 7 0 0
S e r i e s
Parts of the PPT 2700
Front View
Scan LED
Scan Trigger
WAN Antenna
(PPT 2733/34 only)
APP5 Button
(Start Menu)
Scroll Button
Scroll Button
Action Button
Right Scan Trigger
LCD (Screen)
Power Button
Function Button
Application Buttons
1 through 4
Left View
Left Scan Trigger
2
Q u i c k
R e f e r e n c e
Parts of the PPT 2700 (continued)
Back View
Stylus
IR Port
Handstrap Connector
Stylus Silo
Microphone
Speaker
Battery Cover
Switch
Reset Button
Battery
Compartment
Lithium Ion
Battery
Battery
Door Latch
Battery
Door Latch
Battery
Door
Bottom View
Serial Port
Top View
(1D Scanning Terminal)
Top View
(2D Scanning Terminal)
Scan Window
3
P P T
2 7 0 0
S e r i e s
Installing Batteries
Before using your PPT 2700, install a lithium-ion battery:
1. Open the latches on the battery door and lift the battery door
away from the PPT 2700.
Latch
Latch
2. Insert the lithium-ion battery in the battery compartment with
the battery tether positioned properly (as shown below),
making sure the battery snaps into place.
Tether
3. Replace the battery cover, pressing down firmly while securing the latches.
4
Q u i c k
R e f e r e n c e
Charging the Battery
Before using your PPT 2700 for the first time, charge the lithiumion battery in the terminal for about 2 1/2 hours, using the CRD
2700 Cradle or the Synchronization Cable. Follow these same
procedures to recharge the battery.
Your terminal is equipped with a memory backup battery which
automatically charges from the fully-charged lithium-ion battery.
This backup battery retains data in memory when the terminal’s
battery is removed, and takes several hours to charge when you
first use your terminal.
Note:
If you remove your lithium-ion battery before the backup battery is fully charged, data may be lost. For this
reason, DO NOT remove the battery within the first ten
hours of use.
Charging the Battery Using the CRD 2700 Cradle
1. Plug the cradle into a wall outlet.
2. Insert the PPT 2700 terminal in the cradle.
Terminal Charge LED
5
P P T
2 7 0 0
S e r i e s
3. The Terminal Charge LED turns red (may take up to one
minute) to indicate charging, then green when the battery is
fully charged. The terminal’s battery is fully charged after
approximately 2 1/2 hours.
Charging a Spare Battery
To recharge a terminal’s spare battery, insert it in the spare battery
charging slot in the back of the cradle, oriented so the contacts are
facing down and toward the back of the cradle. Press the battery
down into the slot until firmly seated.
The Spare Battery Charge LED turns red to indicate charging,
then green when the battery is fully charged. The battery is fully
charged after approximately 2 1/2 hours. See the PPT 2700
Cradle Quick Reference Guide (p/n 70-37807-xx) for more
information.
Spare Battery
Charge LED
6
Q u i c k
R e f e r e n c e
Charging the Battery Using the Synchronization Cable
1. Insert the cable into the bottom of the terminal.
Synchronization Cable
2. Plug the power cable into a wall outlet and plug the other end
into the battery charging receptacle on the side of the Synchronization Cable.
Battery Charging
Receptacle
7
P P T
2 7 0 0
S e r i e s
Starting the PPT 2700
Press the red power button to start the terminal. If the terminal
does not power on, perform a hard reset. See Performing a Hard
Reset on page 18.
Power
Button
As the terminal initializes its unique Flash File system, the Symbol
splash screen displays for about a minute.
When the Welcome screen appears, tap anywhere on the screen
to continue to the Align screen. Note that these screens also
appear every time you perform a hard reset.
Aligning the Screen
To align your PPT 2700 so the cursor on the touch screen aligns
with the tip of your stylus:
1. If necessary, adjust the contrast on the PPT 2700 so the
screen is readable. See Controlling the Contrast/Backlight
on page 9.
2. Remove the stylus from its storage silo on the back of the
PPT 2700.
8
Q u i c k
R e f e r e n c e
3. Tap the center of each target that appears on the screen with
the tip of the stylus.
Tap the target firmly and accurately
at each location on the screen. The
target will continue to move until
the screen is aligned.
4. Follow the directions on the screen which explain how to use
the stylus and pop-up menus, and allow you to set your city
and time zone.
Using the PPT 2700
Using the Power Button
Press the power button on the lower left-hand side of the terminal
to turn the PPT 2700 on and off.
Controlling the Contrast/Backlight
The Function button, shown below, allows you to adjust the
contrast of the screen and control the backlight.
Function Button
Power Button
9
P P T
2 7 0 0
S e r i e s
To adjust the contrast:
1. Press and hold the Function button.
2. Press the “up” scroll button at the top of the terminal to darken the screen, or the “down” scroll button to lighten the
screen.
To turn the backlight on or off:
1. Press and hold the Function button.
2. Press any application button.
Using the Stylus
The stylus selects items and enters information. The stylus
functions as a mouse.
•
•
•
Tap: Touch the screen once with the stylus to open items and
select options.
Drag: Hold the stylus on the screen and drag across the
screen to select text and images. Drag in a list to select multiple items.
Tap-and-hold: Tap and hold the stylus on an item to see a
list of actions available for that item. On the pop-up menu
that appears, tap the action you want to perform.
10
Q u i c k
R e f e r e n c e
Today Screen
When you turn on your terminal for the first time each day (or after
4 hours of inactivity), the Today screen appears. You can also
display it by tapping
, then Today. On the Today screen, you
can see important information for the day.
11
P P T
2 7 0 0
S e r i e s
Navigation Bar and Command Bar
The navigation bar at the top of the screen displays the active
program and current time, and allows you to switch to programs
and close screens. The command bar at the bottom of the screen
contains menus and buttons to perform tasks in programs.
12
Q u i c k
R e f e r e n c e
Input Methods
Enter information in any program by typing with the soft keyboard
or writing using Character Recognizer.
The Character Recognizer input panel is divided into three writing
areas. Letters written in the left area (labeled ABC) create
uppercase letters and letters written in the middle area (labeled
abc) create lowercase letters. The right area (labeled 123) is for
writing numbers, symbols, special characters, and punctuation.
The following chart is a partial display of the characters you can
write while in lowercase mode (the dot on each character is the
starting point for writing). For more information on using Character
13
P P T
2 7 0 0
S e r i e s
Recognizer and for demos of all characters, tap on the Character
Recognizer input panel.
14
Q u i c k
R e f e r e n c e
Scanning with the PPT 2700
The PPT 2700 has an integrated scanner which collects data by
scanning bar codes. See the PPT 2700 Product Reference Guide
for information on configuring your terminal for scanning.
To scan bar codes with the PPT 2700:
1. Aim the scanner at the bar code.
2. Press either the right, left, or center scan trigger. Make sure
the red scan beam covers the entire bar code. The green
scan LED lights and a beep sounds to indicate a successful
decode.
Scanning PDF417 Bar Codes
The 2D scanning PPT 2700 terminal supports PDF417 bar code
scanning. The raster pattern has multiple scanning rows to
accommodate the PDF417 symbol’s multiple rows.
1. Point the scanner at the bar code and press the trigger.
2. Center the aiming pattern (a spot or slab raster, as programmed) on the bar code.
3. As the raster pattern spreads, keep the pattern horizontal to
the bar code. Be sure the pattern extends about 3/4” beyond
both sides of the bar code.
3/4”
3/4”
15
P P T
2 7 0 0
S e r i e s
4. The LED blinks red to indicate that the terminal is decoding.
5. The LED turns green and the terminal beeps when the bar
code is decoded. The bar code data displays on the screen.
“Tall” PDF Bar Codes
If the PDF417 symbol is too tall for the vertical scan pattern to
cover, move the terminal slowly up and down, keeping the beam
horizontal to the symbol’s rows, until the pattern scans the entire
symbol.
The scan beam does not have to be perfectly parallel with the top
and bottom of the symbol (up to a 4o tilt will work).
16
Q u i c k
R e f e r e n c e
Resetting Your PPT 2700 Terminal
If your PPT 2700 terminal stops responding to input, reset it.
Performing a Soft Reset
A soft reset restarts the terminal and saves all stored records and
entries.
Caution:
Files that remain open during a soft reset may not be
retained.
Caution:
DO NOT perform a soft reset if the terminal is suspended. Press the Power button to wake the terminal.
To perform a soft reset, hold down both the up and down scroll
buttons, then press the App 4 button.
Up & Down
Scroll Buttons
App 4 Button
17
P P T
2 7 0 0
S e r i e s
Performing a Hard Reset
A hard reset also restarts your PPT 2700 terminal, but erases all
stored records and entries. Therefore, never perform a hard reset
unless a soft reset does not solve your problem.
Note:
You can restore any data previously synchronized with
your computer during the next ActiveSync operation.
See the PPT 2700 Cradle Quick Reference Guide or
the PPT 2700 Product Reference Guide.
To perform a hard reset:
1. Remove the battery cover.
2. While holding down the Function button, use the stylus (or
similar object without a sharp tip) to gently press the reset
button.
Function
Button
Reset
Button
3. Replace the battery cover and press the Power button.
4. As the terminal initializes its unique Flash File system, the
Symbol splash screen displays for about a minute.
5. See Aligning the Screen on page 8 to perform an initial setup
of the terminal.
Note:
With a hard reset, Formats, Preferences, and other
settings are restored to their factory default settings.
18
Q u i c k
R e f e r e n c e
Maintaining the PPT 2700
For trouble-free service, observe the following tips when using
your PPT 2700:
•
•
•
•
•
•
Do not scratch the screen. Use the supplied stylus or plastictipped pens intended for use with a touch-sensitive screen.
Never use a pen or pencil or other sharp object on the
screen.
Although your PPT 2700 is water and dust resistant, do not
expose it to rain or moisture for an extended period of time.
Treat your PPT 2700 as you would a pocket calculator or other small electronic instrument.
The touch-sensitive screen of your PPT 2700 contains glass.
Do not drop your PPT 2700 or subject it to strong impact.
Protect your PPT 2700 from temperature extremes. Do not
leave it on the dashboard of a car on a hot day, and keep it
away from heat sources.
Do not store or use your PPT 2700 in any location that is extremely dusty, damp or wet.
If the surface of the PPT 2700 screen becomes soiled, clean
it with a soft cloth moistened with a diluted window-cleaning
solution.
Troubleshooting
•
•
•
Adjust the contrast control.
Make sure batteries are installed properly.
Replace the batteries. If your PPT 2700 terminal still does
not operate, try a soft reset, then a hard reset; see Resetting
Your PPT 2700 Terminal on page 17.
No sound:
•
Check the System Volume slider in the Sounds & Reminders properties dialog box (under Start/Settings) to make
19
P P T
2 7 0 0
S e r i e s
sure the volume is not turned down.
PPT 2700 terminal turns itself off:
•
Your PPT 2700 terminal turns off after a period of inactivity.
This period can be set from one to five minutes, in oneminute intervals. Check the Power dialog box (in the System tab under Start/Settings), and change the setting if you
need a longer delay before the automatic shutoff feature activates.
PPT 2700 terminal doesn’t recognize my handwriting:
•
For your PPT 2700 to recognize handwriting input with the
stylus, characters must be written a certain way. See the
PPT 2700 Product Reference Guide for information about
how to write character strokes.
• Make the character strokes in the lower character entry area
on the screen — not on the display part of the screen.
• Make sure you are writing lower-case letters in the left-hand
side, numbers in the right-hand side, and upper-case letters
in the center of the writing area.
Tapping the screen buttons or icons does not activate the
corresponding feature:
•
Align the screen. Choose Align Screen from the System tab
under Start/Settings, or hold down the Function button and
press the Action button.
A message appears stating that your PPT 2700 terminal
memory is full:
•
•
•
Delete unused memos and records. You can save these
records on your computer.
Adjust the memory allocation. Select Start, then Settings,
and select the System tab. Tap Memory and adjust the slider.
If you have installed additional applications on your PPT
20
Q u i c k
R e f e r e n c e
2700 terminal, remove them to recover memory. Select
Start, then Settings, and select the System tab. Tap Remove Programs, select the unused program and tap Remove.
Beamed data does not transmit:
•
•
Confirm that the PPT 2700 terminals are 5” apart, and there
is a clear path between the two devices.
Adjust the room lighting or move to a different location.
When receiving beamed data an out of memory message
appears:
•
Your PPT 2700 terminal requires at least twice the amount of
memory available as the data you are receiving. For example, if you are receiving a 30K application, you must have at
least 60K free.
Your PPT 2700 unit does not accept scan input:
•
Verify that the unit is loaded with a scanning application. See
your System Administrator.
• Be sure the symbol is not defaced.
• Be sure you are within proper scanning range.
• Be sure the terminal is programmed to accept the type of bar
code you are scanning.
• If you are expecting a beep on a good decode and don’t hear
one, check that the application is set to generate a beep on
good decode.
• If the scanner stops emitting a laser beam when you press
the trigger, check your battery level. When the battery is low,
the scanner shuts off before the terminal notifies you of the
low battery condition.
Note: If the scanner is still not reading symbols, contact your
distributor or Symbol Technologies.
21
P P T
2 7 0 0
S e r i e s
MICROSOFT WINDOWS FOR POCKET PC
DATA EXCHANGE COMPONENT: MICROSOFT ACTIVESYNC, VERSION 3.1
IMPORTANT-READ CAREFULLY: This End-User License Agreement (“EULA”) is a
legal agreement between you (either an individual or a single entity) and the
manufacturer (“Manufacturer”) of the special purpose computing device (“SYSTEM”)
with which you acquired the Microsoft software product(s) identified above
(“SOFTWARE”). The SOFTWARE includes computer software, the associated
media, any printed materials, and any “online” or electronic documentation. Any
software provided along with the SOFTWARE that is associated with a separate enduser license agreement is licensed to you under the terms of that license agreement.
By installing, copying, downloading, accessing, or otherwise using the SOFTWARE,
you agree to be bound by the terms of this EULA. If you do not agree to the terms of
this EULA, Manufacturer and Microsoft Licensing, Inc. (“MS”) are unwilling to license
the SOFTWARE to you. In such event, you may not use or copy the SOFTWARE, and
you should promptly contact Manufacturer for instructions on return of the unused
product(s) in accordance with Manufacturer's return policies.
The SOFTWARE is protected by copyright laws and international copyright treaties,
as well as other intellectual property laws and treaties. The SOFTWARE is licensed,
not sold.
1. GRANT OF LICENSE. SOFTWARE includes software already installed on the
SYSTEM (“SYSTEM Software”) and, if included in the SYSTEM package, software contained on the CD-ROM disc labeled “Desktop Software for Microsoft
Windows CE Microsoft ActiveSync 3.1” (“Desktop Software”). This EULA grants
you the following rights to the SOFTWARE:
• SYSTEM Software. You may use the SYSTEM Software as installed on the
SYSTEM.
• Desktop Software. If Desktop Software is included with your SYSTEM, you
may install and use the Data Exchange component identified above on one (1)
or more computers to exchange information with one (1) or more computing
devices that contain a compatible version of the Microsoft Windows CE operating system. For other software component(s) contained in the Desktop Software, you may install and use such components only in accordance with the
terms of the printed or online end-user license agreement(s) provided with such
component(s). In the absence of an end user license agreement for particular
component(s) of the Desktop Software, you may install and use only one (1)
copy of such component(s) on the SYSTEM or a single computer with which
you use the SYSTEM.
• Backup Copy. If Manufacturer has not included a backup copy of the SYSTEM
Software with the SYSTEM, you may make a single backup copy of the SYSTEM Software. You may use the backup copy solely for archival purposes.
• Microsoft Outlook 2000. The following terms apply to your use of Microsoft
Outlook 2000 (i) regardless of the information contained in the “Software Installation and Use” section of the online EULA you may install one (1) copy of
22
Q u i c k
R e f e r e n c e
Microsoft Outlook 2000 on one (1) computer to use, exchange data, share data,
access, and interact with the SYSTEM, and (ii) the EULA is between Manufacturer (as defined above) and the end user-not between the PC Manufacturer
and end user.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
• Speech/Handwriting Recognition. If the SOFTWARE includes speech and/or
handwriting recognition component(s), you should understand that speech and
handwriting recognition are inherently statistical processes; that recognition
errors are inherent in the processes; that it is your responsibility to provide for
handling such errors and to monitor the recognition processes and correct any
errors. Neither Manufacturer nor its suppliers shall be liable for any damages
arising out of errors in the speech and handwriting recognition processes.
• Limitations on Reverse Engineering, Decompilation, and Disassembly.
You may not reverse engineer, decompile, or disassemble the SOFTWARE,
except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.
• Single SYSTEM. The SYSTEM Software is licensed with the SYSTEM as a
single integrated product. The SYSTEM Software installed in read-only memory
(“ROM”) of the SYSTEM may only be used as part of the SYSTEM.
• Single EULA. The package for the SYSTEM may contain multiple versions of
this EULA, such as multiple translations and/or multiple media versions (e.g., in
the user documentation and in the software). Even if you receive multiple versions of the EULA, you are licensed to use only one (1) copy of the SYSTEM
Software.
• Rental. You may not rent or lease the SOFTWARE.
• Software Transfer. You may permanently transfer all of your rights under this
EULA only as part of a sale or transfer of the SYSTEM, provided you retain no
copies, you transfer all of the SOFTWARE (including all component parts, the
media and printed materials, any upgrades or backup copies, this EULA and, if
applicable, the Certificate(s) of Authenticity), and the recipient agrees to the
terms of this EULA. If the SOFTWARE is an upgrade, any transfer must include
all prior versions of the SOFTWARE.
• Termination. Without prejudice to any other rights, Manufacturer or MS may
terminate this EULA if you fail to comply with the terms and conditions of this
EULA. In such event, you must destroy all copies of the SOFTWARE and all of
its component parts.
3. UPGRADES AND RECOVERY MEDIA.
• SYSTEM Software. If the SYSTEM Software is provided by Manufacturer separate from the SYSTEM on media such as a ROM chip, CD-ROM disc(s) or via
Web download or other, means, and is labeled “For Upgrade Purposes Only” or
“For Recovery Purposes Only,” you may install one copy of such SYSTEM Soft-
23
P P T
2 7 0 0
S e r i e s
ware onto the SYSTEM as a replacement copy for the existing SYSTEM Software and use it in accordance with Section 1 of this EULA.
• Desktop Software. If any Desktop Software component(s) is provided by Manufacturer separate from the SYSTEM on CD-ROM disc(s) or via Web download
or other means, and labeled “For Upgrade Purposes Only” or “For Recovery
Purposes Only”, you may (i) install and use one copy of such component(s) on
the computer(s) you use to exchange data with the SYSTEM as a replacement
copy for the existing Desktop Software component(s).
4. COPYRIGHT. All title and intellectual property rights in and to the SOFTWARE (including, but not limited to, any images, photographs, animations, video, audio,
music, text, and “applets” incorporated into the SOFTWARE), the accompanying
printed materials, and any copies of the SOFTWARE, are owned by MS or its suppliers (including Microsoft Corporation). You may not copy the printed materials
accompanying the SOFTWARE. All title and intellectual property rights in and to
the content which may be accessed through use of the SOFTWARE is the property of the respective content owner and may be protected by applicable copyright
or other intellectual property laws and treaties. This EULA grants you no rights to
use such content. All rights not specifically granted under this EULA are reserved
by MS and its suppliers (including, Microsoft Corporation).
5. EXPORT RESTRICTIONS. You agree that you will not export or re-export the
SOFTWARE to any country, person, or entity subject to U.S. export restrictions.
You specifically agree not to export or re export the SOFTWARE: (i) to any country
to which the U.S. has embargoed or restricted the export of goods or services,
which as of May 1999 include, but are not necessarily limited to, Cuba, Iran, Iraq,
Libya, North Korea, Sudan, Syria, and the Federal Republic of Yugoslavia (including Serbia, but not Montenegro), or to any national of any such country, wherever
located, who intends to transmit or transport the products back to such country;
(ii) to any person or entity who you know or have reason to know will utilize the
SOFTWARE or portion thereof in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been
prohibited from participating in U.S. export transactions by any federal agency of
the U.S. government.
6. NOTE ON JAVA SUPPORT. The SOFTWARE may contain support for programs
written in Java. Java technology is not fault tolerant and is not designed, manufactured, or intended for use or resale as online control equipment in hazardous
environments requiring fail-safe performance, such as in the operation of nuclear
facilities, aircraft navigation or communication systems, air traffic control, direct
life support machines, or weapons systems, in which the failure of Java technology could lead directly to death, personal injury, or severe physical or environmental damage. Sun Microsystems, Inc. has contractually obligated Microsoft
Corporation to make this disclaimer.
7. PRODUCT SUPPORT. Product support for the SOFTWARE is not provided by
MS, its parent corporation, Microsoft Corporation, or their affiliates or subsidiaries.
For product support, please refer to Manufacturer's support number provided in
the documentation for the SYSTEM. Should you have any questions concerning
this EULA, or if you desire to contact Manufacturer for any other reason, please
24
Q u i c k
R e f e r e n c e
refer to the address provided in the documentation for the SYSTEM.
FOR THE LIMITED WARRANTIES AND SPECIAL PROVISIONS PERTAINING TO
YOUR PARTICULAR JURISDICTION, PLEASE REFERTO YOUR WARRANTY
BOOKLET INCLUDED WITH THIS PACKAGE OR PROVIDED WITH THE
SOFTWARE PRINTED MATERIALS.
Regulatory Information
Radio Frequency Interference Requirements
This device has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the Federal Communications Commissions Rules and
Regulation. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
However, there is no guarantee that interference will not occur in a particular
installation. If the equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC Part 15. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Radio Frequency Interference Requirements - Canada
This device complies with RSS 210 of Industry & Science Canada. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Industry Canada Standard ICES-003.
Cet appareil numérique de la classe B est conform à la norme NMB-003 d’Industrie
Canada.
25
P P T
2 7 0 0
S e r i e s
CE Marking and European Union Compliance
Products intended for sale within the European Union are marked with
the CE Mark which indicates compliance to applicable Directives and
European Normes (EN), as follows. Amendments to these Directives or
ENs are included:
Applicable Directives
• Electromagnetic Compatibility Directive 89/336/EEC
• Low Voltage Directive 73/23/EEC
Applicable Standards
• EN 55 022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information technology Equipment
• EN55024:1998: Information technology equipment- Immunity characteristicsLimits and methods of measurement.
• ETS 300-826:1997: Electromagnetic compatibility and radio spectrum matters
(ERM);Electromagnetic compatibility (EMC) standard for 2.4Ghz wideband
transmission systems and high performance radio local area network (Hiperlan)
equipment.
• IEC 1000-4-2:1995/EN 61000-4-2:1995;Electromagnetic Compatibility (EMC)
Part 4:Testing and Measurement techniques;Section 4.2:Electrostatic discharge
immunity test.
• IEC 1000-4-3:1995/EN61000-4-3:1997, Electromagnetic Compatibility (EMC);
Part 4 Testing and measurement techniques;Section 3.Radiated,radio frequency.electromagnetic field immunity test.
• IEC 1000-4-4:1995/EN61000-4-4:1995;Electromagnetic compatibility (EMC)
Part 4;Testing and Measurement techniques;Section 4:Testing electrical fast
transient,/Burst Immunity.
• IEC 1000-4-5:1995/EN61000-4-5;1995,Electromagnetic compatibility (EMC),
Part 4:Testing and Measurement techniques;Section 5:Surge Immunity
• IEC 1000-4-6:1996/EN61000-4-6:1996:Electromagnetic compatibility (EMC),
Part 4:Testing and Measurement techniques;Section 6: Immunity to conducted
disturbances, induced by radio frequency fields.
• IEC 1000-4-11:1994/EN61000-4-11:1994: Electromagnetic compatibility (EMC),
Part 4:Testing and Measurement techniques;Section 11:Voltage Dips, Short
Interruptions, and Voltage Variations.
• EN 60 950 + Amd 1 + Amd 2 - Safety of Information Technology Equipment
Including Electrical Business Equipment
• EN 60 825-1 (EN 60 825) - Safety of Devices Containing Lasers.
RF Devices
Symbol’s RF products are designed to be compliant with the rules and regulations in
the locations into which they are sold and will be labeled as required. The majority of
Symbol’s RF devices are type approved and do not require the user to obtain license
or authorization before using the equipment. Any changes or modifications to Symbol
26
Q u i c k
R e f e r e n c e
Technologies equipment not expressly approved by Symbol Technologies could void
the user’s authority to operate the equipment.
The Spectrum24 equipment is intended for use throughout the European Economic
Area, but it’s authorization for use in France is restricted as follows:
• PAN European Frequency Range: 2.400 - 2.4835 GHz, identified by -EU suffix
to the model number found on the product label.
• France - Restrict Frequency Range for use in France: 2.447 - 2.453 GHz, identified on PPT 2742 by the -FR suffix to the model number found on the product
label.
• Belgium - Operation in an out of doors environment in Belgium must be
restricted to 2460 - 2483.5 MHz band.
• Italy - Operation in Italy requires a user license.
WARNING: FCC RF EXPOSURE GUIDELINES
To satisfy FCC RF exposure compliance requirements for a
portable transmitting device, this device should be used in
hand-held, hand-operated configurations only. The device
and its antenna should generally maintain a separation distance of 20 cm or more from a person's body; except for the
hands and wrists because of higher exposure limit for extremities. This device is designed to be used in a person's
hands and its operating configurations, generally do not support normal transmissions while it is carried in pockets or holsters next to a person's body.
Caution:
RF Devices
Symbol's RF products are designed to be compliant with the
rules and regulations in the locations into which they are sold
and will be labeled as required. The majority of Symbol's RF
devices are type approved and do not require the user to obtain license or authorization before using the equipment. Any
changes or modifications to Symbol Technologies’ equipment not expressly approved by Symbol Technologies could
void the user's authority to operate the equipment.
27
P P T
2 7 0 0
S e r i e s
Laser Devices
Symbol products using lasers comply with US 21CFR1040.10, and IEC825-1:1993,
EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels
on the product.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those
specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
28
Q u i c k
R e f e r e n c e
In accordance with Clause 5, IEC 0825 and EN60825, the following information is
provided to the user:
ENGLISH
CLASS 1
CLASS 2
HEBREW
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
DANISH
KLASSE 1
KLASSE 2
KLASSE 1 LASERPRODUKT
LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
AL LASER DI CLASSE 2
DUTCH
KLASSE 1
KLASSE-1 LASERPRODUKT
KLASSE 2
LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
FINNISH
LUOKKA 1
LUOKKA 2
FRENCH
CLASSE 1
CLASSE 2
GERMAN
KLASSE 1
KLASSE 2
ITALIAN
CLASSE 1
CLASSE 2
PRODOTTO AL LASER DI CLASSE 1
LUCE LASER
NON FISSARE IL RAGGIOPRODOTTO
NORWEGIAN
KLASSE 1
LASERPRODUKT, KLASSE 1
KLASSE 2
LASERLYS IKKE STIRR INN I LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
PORTUGUESE
CLASSE 1
PRODUTO LASER DA CLASSE 1
LUOKKA 1 LASERTUOTE
LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
CLASSE 2
SPANISH
CLASE 1
CLASE 2
PRODUIT LASER DE CLASSE 1
LUMIERE LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
SWEDISH
KLASS 1
KLASS 2
LASERPRODUKT DER KLASSE 1
LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT DER KLASSE 2
29
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
PRODUCTO LASER DE LA CLASE 1
LUZ LASER
NO MIRE FIJAMENTE EL HAZ
PRODUCTO LASER DE LA CLASE 2
LASERPRODUKT KLASS 1
LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
P P T
2 7 0 0
S e r i e s
Battery Caution
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
30
Q u i c k
R e f e r e n c e
DECLARATION OF CONFORMITY
We,
Symbol Technologies, Inc.
of
One Symbol Plaza, Holtsville, NY 11742-1300, USA
declare under our sole responsibility that the product
Spectrum24, LA3021, Type II Radio Card
Spectrum24, LA302C, Type II Radio Card
Spectrum24, LA302T, Type II Radio Card
to which this declaration relates, is in conformity with the following standards and/or
other normative documents.
ETS 300 328 (November 1996)
ETS 300 826 (November 1997)
EN 60950: 1992 Incl Amdt 1-4, 11
We hereby declare that all essential radio test suites have been carried out and that the above
named products is in conformity to al the essential requirements of Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10(5) and detailed in Annex IV of
Directive 1999/5/EC has been followed with the involvement of the following Notified Body(ies):
BABT, Claremont House, 34 Molesey Road, Walton-on-Thames, KT12 4RQ
Identification mark:
0168
The equipment will also carry the
Class 2 equipment identifier
The technical documentation relevant to the above equipment can be made available for
inspection on application to:
Symbol Technologies EMEA, Symbol Place, Winnersh Triangle, Berkshire, RG 41 5TP, UK
Dornu Narnor
(name)
Director, Regulatory and Technical Sales
(title)
3, May 2000
(signature of authorised person)
(date)
31
P P T
2 7 0 0
S e r i e s
DECLARATION OF CONFORMITY
We,
Symbol Technologies, Inc.
of
One Symbol Plaza, Holtsville, NY 11742-1300, USA
declare under our sole responsibility that the product
Spectrum24HR, LA4111, Type II Radio Card
Spectrum24HR, LA411T, Type II Radio Card
to which this declaration relates, is in conformity with the following standards and/or
other normative documents.
ETS 300 328 (November 1996)
ETS 300 826 (November 1997)
EN 60950: 1992 Incl Amdt 1-4, 11
We hereby declare that all essential radio test suites have been carried out and that the above
named products is in conformity to al the essential requirements of Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10(5) and detailed in Annex IV of
Directive 1999/5/EC has been followed with the involvement of the following Notified Body(ies):
BABT, Claremont House, 34 Molesey Road, Walton-on-Thames, KT12 4RQ
Identification mark:
0168
The equipment will also carry the
Class 2 equipment identifier
The technical documentation relevant to the above equipment can be made available for
inspection on application to:
Symbol Technologies EMEA, Symbol Place, Winnersh Triangle, Berkshire, RG 41 5TP, UK
Dornu Narnor
(name)
Director, Regulatory and Technical Sales
(title)
3, May 2000
(signature of authorised person)
(date)
32
Q u i c k
R e f e r e n c e
Warranty
Symbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with
industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of
shipment, products will be free from defects in materials and workmanship.
This warranty is provided to the original owner only and is not transferable to any third party. It shall
not apply to any product (i) which has been repaired or altered unless done or approved by Symbol,
(ii) which has not been maintained in accordance with any operating or handling instructions
supplied by Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse,
abuse, power shortage, negligence or accident or (iv) which has been used other than in
accordance with the product operating and handling instructions. Preventive maintenance is the
responsibility of customer and is not covered under this warranty.
Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty.
Non-serialized items will carry a 30-day limited warranty.
Warranty Coverage and Procedure
During the warranty period, Symbol will repair or replace defective products returned to Symbol’s
manufacturing plant in the US. For warranty service in North America, call the Symbol Support
Center at 1-800-653-5350. International customers should contact the local Symbol office or
support center. If warranty service is required, Symbol will issue a Return Material Authorization
Number. Products must be shipped in the original or comparable packaging, shipping and
insurance charges prepaid. Symbol will ship the repaired or replacement product freight and
insurance prepaid in North America. Shipments from the US or other locations will be made F.O.B.
Symbol’s manufacturing plant.
Symbol will use new or refurbished parts at its discretion and will own all parts removed from
repaired products. Customer will pay for the replacement product in case it does not return the
replaced product to Symbol within 3 days of receipt of the replacement product. The process for
return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the
time of the exchange.
Customer accepts full responsibility for its software and data including the appropriate backup
thereof.
Repair or replacement of a product during warranty will not extend the original warranty term.
Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or
phone support, that can be implemented to meet customer’s special operational requirements and
are available at a substantial discount during warranty period.
General
Except for the warranties stated above, Symbol disclaims all warranties, express or implied, on
products furnished hereunder, including without limitation implied warranties of merchantability and
fitness for a particular purpose. The stated express warranties are in lieu of all obligations or
liabilities on part of Symbol for damages, including without limitation, special, indirect, or
consequential damages arising out of or in connection with the use or performance of the product.
Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way
exceed the purchase price of said product, except in instances of injury to persons or property.
Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential
damages, so the proceeding exclusion or limitation may not apply to you.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and
run your applications.
If you have a problem running your unit or using your equipment, contact your
facility’s Technical or Systems Support. If there is a problem with the equipment, they
will contact the Symbol Support Center:
United States
1-800-653-5350
Canada
905-629-7226
United Kingdom
0800 328 2424
Asia/Pacific
337-6588
Australia
1-800-672-906
Austria
1-505-5794
Denmark
7020-1718
Finland
9 5407 580
France
01-40-96-52-21
Germany
6074-49020
Italy
2-484441
Mexico
5-520-1835
Netherlands
315-271700
Norway
66810600
South Africa
11-4405668
Spain
9-1-320-39-09
Sweden
84452900
Latin America Sales Support
1-800-347-0178 Inside US
+1-561-483-1275 Outside US
Europe/Mid-East Distributor Operations
Contact local distributor or call
+44 208 945 7360
70-37805-02
Revision A — August 2000
Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300
">