Danuser Mini MAC Operator Manual

E STA B L I S H E D 1 9 1 0 • F U LTO N , M I SS O U R I
MINI MAC
Read this entire manual. This
safety alert symbol is used
throughout this manual to call your
attention to messages involving
your personal safety and the safety
of others. Failure to follow these
instructions can result in injury or
death.
1
1WARNING
Si no entiende ingles, se prefiere que
busque a alguien que interprete las
instrucciones para usted.
Owner:
Date Purchased:
Model #:
Manual #:
Serial #:
9MMINIMAC2461222
Operator’s Manual
Danuser Machine Company, LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected]
Website: www.danuser.com
Letter to Owner/Operator
Dear Owner/Operator,
Thank you for purchasing this Danuser Mini MAC. We appreciate your business.
With a 1/4 yard capacity, the Mini MAC is designed to mix, transport, and dispense concrete or
other materials where needed.
Your safety as an operator of our product is very important to us. Therefore, before you
assemble, install, operate, maintain, service, remove, or move your Danuser Mini MAC, read
and understand this manual thoroughly. If there is anything you do not understand, immediately
contact your dealer, or contact our factory direct.
Tel:
E-mail:
(573) 642-2246
[email protected]
Your satisfaction in the performance and longevity of our product is also very important to us and
can be prolonged by proper assembly, installation, operation, and maintenance as instructed in this
manual.
Thank you again for your business and for your trust in our product. Please feel free to contact us
at any time for further assistance.
Sincerely,
Danuser Machine Company, LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected] Website: www.danuser.com
Danuser provides this manual “as is” without warranty of any kind, either expressed or implied. Danuser assumes
no responsibility for errors or omissions. Danuser assumes no liability for damages resulting from the use of the
information contained herein. Danuser reserves the right to revise and improve its products as it sees fit. This manual
describes the state of this product at the time of its publication and may not reflect the product in the future.
Danuser is a registered trademark.
Foreword
Please read this manual thoroughly!
Before you assemble, install, operate, maintain, service, remove, or move your Danuser Mini
MAC, read this manual thoroughly. If there is anything you do not understand, immediately
contact your dealer, or call our factory direct at (573) 642-2246. Powered equipment can be
dangerous if not assembled, installed, operated, maintained, serviced, removed, or moved
properly.
Warranty Registration
To activate your warranty coverage and to provide you with efficient customer service, please
fill out your WARRANTY REGISTRATION FORM. This form is included in your unit’s
paperwork package. If you did not complete a WARRANTY REGISTRATION FORM or
did not receive one, please call Danuser. Or, register online at www.danuser.com. Your
satisfaction with our product and your safety as a user of our product are both very important
to us.
Symbols
This SAFETY ALERT symbol identifies important safety messages. Carefully read
each safety message that follows. Failure to understand and obey a safety message,
or recognize a safety hazard, could result in injury or death to you or others around you. The
operator is ultimately responsible for the safety of himself, as well as others, in the operating
area of the Mini MAC.
1
Symbol
Meaning
1 DANGER
Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
1 WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury,
including hazards that are exposed when guards are
removed.
1 CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
3
Table of
Contents
This is important information for proper use of
this equipment. Failure to comply may lead to
premature equipment failure.
Page
Letter to Owner/Operator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Decals & Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hydraulic Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assembly & Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Removal & Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance & Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Torque Values Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1234
PD 5146
3
Safety
1WARNING
Working with familiar equipment can lead to careless injuries. Read and understand this
manual and the manual for your vehicle before assembling, installing, operating, maintaining,
servicing, removing, or moving the Danuser Mini MAC. If there is anything in this manual
you do not understand, contact your dealer or Danuser. The safe use of this attachment is
strictly up to you, the operator. If this attachment is used, loaned, or rented by any other
person, it is the owner’s responsibility to make certain that the operator prior to operating:
•
•
4
Reads and understands the Operator’s Manual
Is instructed in safe and proper use
•
The Mini MAC is designed to be operated from the vehicle operator station. Keep
bystanders away from the work area. Do not operate with another person in contact with
any part of the Mini MAC.
•
All operators of this attachment must read and understand this entire manual, paying
particular attention to safety messages and operation instructions prior to assembling,
installing, operating, maintaining, servicing, removing, or moving the Mini MAC.
•
Please remember it is also important that you read, understand, and follow the safety
signs on the attachment. Clean or replace all safety signs if they cannot be clearly read
and understood. They are there for your safety as well as the safety of others. Danuser
will furnish new safety signs upon request at no charge.
•
All things with moving parts are potentially hazardous. There is no substitute for a
cautious, safe-minded operator who recognizes potential hazards and follows reasonable
safety practices.
•
Personal protection equipment including hard hat, safety glasses, safety shoes, gloves,
and hearing protection are recommended during assembly, installation, operation,
maintenance, service, removal, or movement of attachment.
•
Exposure to silica dust and other dust hazards can cause serious or fatal respiratory
disease. Use appropriate respiratory protection.
•
When the use of hand tools is required to perform any part of assembly, installation,
operation, maintenance, or service of the attachment, be sure the tools used are designed
and recommended by the tool manufacturer for that specific task.
•
Never check pressurized system for leaks with your bare hand. Wear proper hand and
eye protection and use wood or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate skin and create a serious
medical emergency. If any fluid is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
•
Always use two people to handle heavy, unwieldy components during assembly,
installation, maintenance, service, removal, or movement of the attachment.
•
Never place any part of your body where it would be in danger if movement should occur
during assembly, installation, operation, maintenance, service, removal, or movement of
the Mini MAC.
•
Only properly trained people should operate the equipment. Do not allow anyone
who has not read this entire manual and understood the safety rules, safety signs, and
operation instructions to use this attachment.
•
Never allow children to operate or be around the Mini MAC.
•
Do not use the Mini MAC as a work platform.
Safety
(continued)
•
Do not allow riders on the equipment at any time. There is no safe place for any riders.
•
Never use alcoholic beverages or drugs which can hinder alertness or coordination while
operating this equipment. Consult your doctor about operating the equipment while
taking prescription or over-the-counter medications.
•
Safe operation of equipment requires the operator’s full attention. Avoid distractions
such as a radio, headphones, cell phones, etc. while operating.
•
Stay away from power lines when transporting, raising, or operating the attachment.
Electrocution can occur without direct contact.
•
The Mini MAC must be securely latched to the vehicle. Ensure both locking handles are
in the locked position with pins fully seated. An improperly latched Mini MAC can fall
without warning.
•
Make sure safety grate is in place and secured before operating equipment.
•
Keep hands, feet, hair, jewelry, and clothing away from all moving and/or rotating parts.
•
Never place yourself between the vehicle and the attachment.
•
Never allow anyone under the attachment at any time.
•
Never reach into discharge end of auger.
•
Keep clear of auger while in operation. Never position the material by hand or with any
tool when the auger is rotating.
•
Do not exceed the vehicle’s rated operating load. Use sufficient counterweights. Move
the vehicle slowly when the attachment is raised.
•
Carry the load low. A heavy load can cause instability of the vehicle. Use extreme care
during travel. Slow down on turns and watch out for bumps. Use all safety devices as
recommended in the vehicle operator’s manual.
•
For operator safety, always keep the load in front of the vehicle. Load should never be
tilted toward or positioned over the operator.
•
Do not operate the Mini MAC on steep hillsides. When operating the Mini MAC
on uneven or hilly terrain, position the vehicle with the attachment uphill. With the
attachment downhill, the vehicle could tip when attempting to raise the Mini MAC.
Consult your vehicle operator’s manual for maximum incline allowable.
•
Always shut off the vehicle engine, remove the key, lower vehicle arms, and relieve all
hydraulic pressure before dismounting the vehicle. Never leave equipment unattended
with the vehicle running.
•
Never attempt adjustments, service, or repairs while the equipment is in operation.
•
Never work under equipment supported by hydraulics. Even with the vehicle shut off,
equipment can suddenly drop if controls are actuated or if hydraulic lines burst.
•
Before connecting or disconnecting hydraulic lines or fittings, be sure to relieve all
pressure by cycling all hydraulic controls after shutdown. Remember hydraulic systems
are under pressure whenever the engine is running and may hold pressure after shutdown.
•
Store the attachment on a flat, level surface where children do not play. Securely block
and support the attachment.
•
Do not modify the attachment. Modifications can weaken the integrity of the attachment
and may impair the safety, function, life, and performance of the Mini MAC.
5
Safety
•
When making repairs or servicing the Mini MAC, use only parts that meet the original
equipment manufacturer’s standards and requirements.
(continued)
•
Always use care when operating the Mini MAC. Most accidents occur because of
neglect or carelessness.
Safety is a primary concern in the design, manufacture, sale, and use of the Mini MAC.
Danuser confirms to you, our customer, our concern for safety.
1 DANGER
Improper operation of this Mini MAC can cause serious
personal injury or death. Operation of this attachment
should only be done by a competent adult acting in
compliance with the Operator’s Manual. Since Mini MAC
operations are beyond our control, we disclaim all liability
for any damages, injuries or death which may result.
2 CALIFORNIA WARNING
This product can expose you to chemicals including lead,
which are known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov.
6
Decals &
Safety Signs
The Mini MAC comes equipped with all safety signs in place. Their locations are shown in
this section. Read and follow their instructions and ensure their care:
•
•
•
Keep safety signs clean and legible at all times.
Replace safety signs that are missing, illegible, or damaged.
Ensure replacement parts installed during repair have safety signs attached.
To install new safety signs, follow these steps:
PART NO. DANUSER109
Locations: Hopper, both sides
1.
2.
3.
4.
Clean the area where the safety sign is to be placed.
Spray a little soapy water on the surface where the safety sign is to be placed.
Peel the backing from the safety sign, and apply it in the position shown.
Firmly press the safety sign, and squeeze out the air bubbles with a straight edge (e.g., a
credit card).
PART NO. DIG47
Locations: Hopper, both sides
PART NO. 256012
Locations: Hopper, both sides
PART NO. DIG30
Locations: Hopper, both sides
PART NO. DIG15
Locations: Hopper,
both sides
PART NO. DIG13
Locations: Hopper,
both sides
PART NO. DIG46
Locations: Hopper, both sides
PART NO. DIG52
Location: Hopper,
discharge end
1WARNING
Clean or replace all safety
signs if they cannot be
clearly read and understood.
7
Decals &
Safety Signs
(continued)
PART NO. DIG35
Locations: Hopper, motor end
PART NO. DIG5
Location: Hopper, motor end
Model No. & Serial No.
Location: Hopper, motor end
1WARNING
Clean or replace all safety
signs if they cannot be
clearly read and understood.
8
PART NO. CA65
Location: Hopper, motor end
Specifications
Mini Universal Mount
E
B
A
C
Mini MAC - Mini Universal Mount
Operator's Manual
Direction Terminology
Front
Left
Right
Rear
D
Height, Grate Lowered (A)
30”
Height, Grate Open (B)
48.5”
Overall Width (C)
24.5”
Overall Length (D)
54”
Overall Hopper Length (E)
38.7”
Weight
370 lb.
Auger Diameter
6.12”
Center Column Diameter
1.32” O.D.
.18” wall
Auger Length
27.5”
Flighting Spacing
4”
Capacity
1/4 yard (6.75 ft3)
80-lb. Bags Concrete Mix
Approx. 9 (1/4 yd)
Dispense Rate
14 seconds @ 24 GPM
Hydraulic Requirements
Up to 24 GPM
Up to 3,500 PSI
Mounting Options
Common Industry Interface (CII)
9
Specifications
Bob-Tach® Mount
E
B
A
C
Mini MAC - Bob-Tach® Mount
Operator's Manual
Direction Terminology
Front
Left
Right
Rear
10
D
Height, Grate Lowered (A)
30”
Height, Grate Open (B)
48.5”
Overall Width (C)
36.5”
Overall Length (D)
55”
Overall Hopper Length (E)
38.7”
Weight
435 lb.
Auger Diameter
6.12”
Center Column Diameter
1.32” O.D.
.18” wall
Auger Length
27.5”
Flighting Spacing
4”
Capacity
1/4 yard (6.75 ft3)
80-lb. Bags Concrete Mix
Approx. 9 (1/4 yd)
Dispense Rate
14 seconds @ 24 GPM
Hydraulic Requirements
Up to 24 GPM
Up to 3,500 PSI
Mounting Options
Bob-Tach® for Mini Track Loaders
Hydraulic
Requirements
Filtration Requirements:
•
A filter of, at least, 10 micron filtration is required.
3
The life of the hydraulic motor is almost entirely dependent upon cleanliness of the
oil. Instructions in your vehicle operator’s manual regarding filter and oil changes
should be carefully followed. Even small amounts of dirt in the hydraulic oil can
cause premature motor failure that is not covered by warranty.
Pressure and Flow Requirements:
•
The Mini MAC is designed to operate up to 24 GPM and up to 3,500 PSI.
Hydraulic Fluid Selection Requirements:
•
Premium grade petroleum-based fluids will provide the best performance.
•
Fluids that contain anti-wear agents, rust inhibitors, anti-foaming agents, and oxidation
inhibitors are recommended.
•
The viscosity of the fluid should never fall below 70 SUS (13 cST). The best viscosity
range for the Mini MAC is 100-200 SUS (20-43 cST).
11
Assembly &
Installation
Prepare the Vehicle
Read and understand the manual for your vehicle before assembling or installing the Mini
MAC. The vehicle must be equipped with auxiliary hydraulics and a mini-skid-steer quick
attach mount. The use of the Mini MAC may require the addition of counterweights to ensure
the combined weight of the attachment and load does not exceed the rated capacity of your
vehicle.
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1WARNING
Do not exceed the vehicle’s rated operating load. If
necessary, use sufficient counterweights.
Recommended Tools
•
•
9/16” wrench
3/4" wrench
•
•
3/4" socket and ratchet
Metal snips
STEP 1:  Using metal snips, remove banding that is securing Mini MAC and Bob-Tach®
mount (if equipped) to the pallet along with any other packaging materials.
STEP 2:  Using a 9/16” wrench, remove the bolts securing the Mini MAC to the pallet.
If the Mini MAC is not equipped with the Bob-Tach® mount, skip to Step 4.
STEP 3:  Locate the hardware bag. Using the provided bolts, washers, and nuts, install the
Bob-Tach® mount to the bucket as shown. Tighten the hardware using a 3/4"
wrench and a 3/4" socket and ratchet. Tighten the nut to the torque specified in the
Torque Values Chart.
STEP 4:  Park the vehicle on level ground, and install the Mini MAC by following your
vehicle operator’s manual for installing an attachment.
1WARNING
The Mini MAC must be securely latched to the vehicle.
Ensure both locking handles are in the locked position with
pins fully seated. An improperly latched Mini MAC can fall
without warning.
12
Assembly &
Installation
STEP 5:  Connect the hydraulic hoses to the vehicle’s auxiliary hydraulics. Test the vehicle
to make sure you have enough hose length to perform the full range of the loader
arms’ operating heights.
(continued)
1WARNING
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is running
and may hold pressure after shutdown.
3
3
Ensure quick couplers are clean prior to connection.
Hose routing is the responsibility of the operator. Pinched and/or stretched hoses
are not covered under the warranty.
1 WARNING
STEP 6:  Engage the vehicle’s auxiliary hydraulics to make sure the Mini MAC auger freely
rotates forward and reverse.
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
STEP 7:  Check the hydraulic system for leaks.
1WARNING
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
Operation
Dispense
1 DANGER
The Mini MAC is designed
to be operated from the
vehicle operator station.
Keep bystanders away
from the work area. Do
not operate with another
person in contact with the
Mini MAC.
1 DANGER
Stay away from power lines when transporting, raising, or
operating the attachment. Electrocution can occur without
direct contact.
1WARNING
Before you operate the attachment, check over pins and
connections to be sure all are securely in place. Make sure
the Mini MAC is securely latched to the vehicle. Make sure
the safety grate is properly installed.
STEP 1:  Ensure the Mini MAC is properly attached.
13
Operation
Dispense
(continued)
STEP 2:  Close the gate on the discharge end by lifting on the handle (A) and rotating it to
the left or right. Once closed, lower the handle and ensure it locks into one of the
slots in the latch plate (B).
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1 WARNING
Safe operation of
equipment requires the
operator’s full attention.
Avoid distractions such
as radio headphones,
cell phones, etc. while
operating.
1 WARNING
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
1 DANGER
Do not use the Mini MAC
as a work platform.
1 DANGER
Do not allow riders on the
equipment at any time.
There is no safe place for
any riders.
14
A
B
STEP 3:  Add material(s) to the hopper.
1WARNING
Do not exceed the vehicle’s rated operating load. If
necessary, use sufficient counterweights.
1 DANGER
Do not operate Mini MAC without safety grate in place and
closed.
STEP 4:  Position the vehicle and, if necessary, attach chute(s) to reach the desired
dispensing location.
1 DANGER
For operator safety, always keep the load in front of the
vehicle. Load should never be tilted toward or positioned
over the operator.
1WARNING
Carry the load low. A heavy load can cause instability of
the vehicle. Use extreme care during travel. Slow down on
turns and watch out for bumps. Use all safety devices as
recommended in the vehicle operator’s manual.
STEP 5:  Open the gate on the discharge end by lifting on the handle and rotating it towards
the center. Once open, lower the handle and ensure it locks into one of the center
slots in the latch plate.
Operation
STEP 6:  Run the auger in the forward direction to dispense material(s)
1 DANGER
Dispense
(continued)
Do not operate with another person in contact with the Mini
MAC.
1 WARNING
Never place yourself
between the vehicle and
the attachment.
Never reach into discharge end of auger.
3
If dispensing and the auger locks up, material may be lodged between the auger
and the side of the hopper. Run the auger in the opposite direction to attempt
to remove the bind. If this is unsuccessful, some material(s) may need to be
removed. Over a clear, designated area, lift the hopper and tilt it forward in
increments, testing the auger until the auger breaks free and begins moving
material again.
STEP 7:  Shut off the vehicle’s auxiliary hydraulics when dispensing is complete.
Operation
Concrete Mixing &
Dispensing
1 DANGER
Stay away from power lines when transporting, raising, or
operating the attachment. Electrocution can occur without
direct contact.
1 DANGER
1WARNING
The Mini MAC is designed
to be operated from the
vehicle operator station.
Keep bystanders away
from the work area. Do
not operate with another
person in contact with the
Mini MAC.
STEP 1:  Ensure the Mini MAC is properly attached.
1 WARNING
STEP 2:  Close the gate on the discharge end by lifting on the handle (A) and rotating it to
the left or right. Once closed, lower the handle and ensure it locks into one of the
slots in the latch plate (B).
Exposure to silica dust
and other dust hazards
can cause serious or fatal
respiratory disease. Use
appropriate respiratory
protection.
Before you operate the attachment, check over pins and
connections to be sure all are securely in place. Make sure
the Mini MAC is securely latched to the vehicle. Make sure
the safety grate is properly installed.
A
B
15
Operation
Concrete Mixing &
Dispensing
(continued)
STEP 3:  Add material(s) to the dispensing end of the hopper and liquid to the motor end.
3
1 DANGER
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
Do not operate the Mini MAC without safety grate in place
and closed.
STEP 4:  Run the auger in reverse to bring the dry material(s) to the liquid.
STEP 5:  Add more dry material(s) and liquid to get the volume and mixture required.
3
3
1 WARNING
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
1 DANGER
Do not use the Mini MAC
as a work platform.
1 DANGER
Do not allow riders on the
equipment at any time.
There is no safe place for
any riders.
If mixing and the auger locks up, material may be lodged between the auger and
the side of the hopper. Momentarily run the auger in the opposite direction to
attempt to remove the bind.
Motor stalling could occur if the mixture is too dry.
1WARNING
1 WARNING
Safe operation of
equipment requires the
operator’s full attention.
Avoid distractions such
as radio headphones,
cell phones, etc. while
operating.
Use the safety grate to break open bags by tossing a bag onto the bag breakers and
rocking the bag back and forth until it splits, dumping material(s) into the hopper.
Do not exceed the vehicle’s rated operating load. If
necessary, use sufficient counterweights.
3
If the mixture becomes too dry, it may be necessary to shovel material from the
sides and corners of the hopper. Follow these steps to shovel material(s):
1 DANGER
Do not operate with another person in contact with the Mini
MAC.
Never reach into discharge end of auger.
1 DANGER
Keep clear of auger while in operation. Never position the
material by hand or with any tool when the auger is rotating.
A:
If material begins to build up on the sides of the hopper, stop mixing.
B:
Rest the Mini MAC on a solid, level surface, and deactivate all hydraulics.
C:
Open the safety grate to gain access to the inside of the hopper.
1WARNING
Ensure safety grate is properly resting in the open position.
16
D:
Shovel the material away from the sides and toward the center of the hopper.
E:
Close the safety grate.
Operation
1 DANGER
Concrete Mixing &
Dispensing
(continued)
1 WARNING
Do not operate Mini MAC without the safety grate in place
and closed.
STEP 6:  When mixing is complete, position the vehicle and, if necessary, attach additional
chute(s) to reach the desired dispensing location.
1 DANGER
Never place yourself
between the vehicle and
the attachment.
For operator safety, always keep the load in front of the
vehicle. Load should never be tilted toward or positioned
over the operator.
1WARNING
Carry the load low. A heavy load can cause instability of
the vehicle. Use extreme care during travel. Slow down on
turns and watch out for bumps. Use all safety devices as
recommended in the vehicle operator’s manual.
STEP 7:  Open the gate on the discharge end by lifting on the handle and rotating it towards
the center. Once open, lower the handle and ensure it locks into one of the center
slots in the latch plate.
STEP 8:  Run the auger in the forward direction to dispense material(s).
1 DANGER
Do not operate with another person in contact with the Mini
MAC.
Never reach into discharge end of auger.
3
If dispensing and the auger locks up, material may be lodged between the auger
and the side of the hopper. Run the auger in the opposite direction to attempt
to remove the bind. If this is unsuccessful, some material(s) may need to be
removed. Over a clear, designated area, lift the hopper and tilt it forward in
increments, testing the auger until the auger breaks free and begins moving
material again.
STEP 9:  Shut off the vehicle’s auxiliary hydraulics when dispensing is complete.
17
Cleaning
1 DANGER
Never attempt
adjustments, service,
or repairs while the
equipment is in operation.
Depending upon the material dispensed, it may be necessary to add a cleaner or appropriate
releasing agent to aid in cleaning the Mini MAC.
STEP 1:  With the gate open, run the Mini MAC until all of the material is dispensed from
the bucket.
STEP 2:  A second person, standing a safe distance away from the Mini MAC, should add
water to the dispensing end of the hopper while the operator runs the auger in
reverse, agitating the water and cleaning the hopper.
1 DANGER
Do not operate with another person in contact with the Mini
MAC. Never reach into discharge end of auger.
1 DANGER
Never allow anyone under
the attachment at any
time.
1 WARNING
STEP 3:  Run the auger in the forward direction to dispense the watery mixture.
3
3
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1 WARNING
Safe operation of
equipment requires the
operator’s full attention.
Avoid distractions such
as radio headphones,
cell phones, etc. while
operating.
18
If necessary, raise the hopper and tilt it forward to rinse out any remaining material.
If necessary, to clean build-up in hard-to-reach areas, open the safety grate. Once
the build-up is removed, close safety grate.
1 DANGER
Do not operate the Mini MAC without safety grate in place
and closed.
STEP 4:  Level the Mini MAC, and lower it to the ground.
STEP 5:  Shut off the vehicle engine, relieve all hydraulic pressure, and remove the vehicle
key before leaving the vehicle operator station.
STEP 6:  Remove the one (1) klik pin and lift the discharge rubber flap at the discharge end
of the bucket. Clean it with water. Make sure there is not any material between
the auger and the discharge tube, or between the discharge tube and gate seal.
STEP 7:  Close the discharge rubber flap, and secure it with the one (1) klik pin.
STEP 8:  Depending upon the material dispensed, coat the hopper with a rust protectant or
concrete releasing agent.
3
Do not allow material(s) to dry or water to freeze in the hopper. This will cause
damage to the auger and the hopper.
STEP 9:  Leave the discharge gate in the open position to allow liquid(s) to escape during
storage.
Removal &
Storage
Before storage, the Mini MAC should be thoroughly cleaned (refer to Cleaning). Make sure
the hydraulic system is properly sealed against contaminants entering the unit. Always store
the Mini MAC in a dry, covered location.
STEP 1:  Lower the Mini MAC onto a flat, level surface in an area where children do not
play.
1 DANGER
STEP 2:  Disconnect the hydraulic hoses from the vehicle’s auxiliary hydraulics.
1WARNING
Never allow anyone under
the attachment at any
time.
Before connecting or disconnecting hydraulic lines or
fittings, be sure to relieve all pressure by cycling all
hydraulic controls after shutdown. Remember hydraulic
systems are under pressure whenever the engine is running
and may hold pressure after shutdown.
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1 CAUTION
3
Connect the quick couplers together to prevent contaminants from entering the
Mini MAC’s hydraulic system.
STEP 3:  Follow your vehicle operator’s manual for removing an attachment. Securely
block and support the Mini MAC.
STEP 4:  Tighten any loose nuts, bolts, and hydraulic components.
STEP 5:  Replace any damaged or missing safety signs.
STEP 6:  Lubricate the grease zerk.
Always use two people to
handle heavy, unwieldy
components during
assembly, installation,
maintenance, service,
removal, or movement of
the attachment.
19
Troubleshooting
Problem
Auger does not rotate
Possible Cause
Solution
Air in hydraulic system
Actuate hydraulics until auger has made one full rotation in
forward and in reverse.
Sheared key or roll pin
Remove auger and replace damaged component.
Hydraulic hose pinched or obstructed
Fix pinched hose or remove obstruction.
Leaking or failed hydraulic hose
Replace hydraulics hose.
Quick couplers not engaged
Check quick coupler connects to vehicle.
Vehicle auxiliary hydraulics not activated Activate auxiliary hydraulics.
Poor auger performance
Leaking hopper
Safety grate hard to open
Vehicle low on hydraulic oil
Add hydraulic oil to vehicle.
Motor damaged
Contact Danuser.
Auger locked up or compacted
Refer to Concrete Mixing & Dispensing.
Low flow
Check with flow meter. If low, investigate cause.
Hydraulic hose restrictions
Clear hydraulic hose.
Dirty oil or filter
Change oil and filter according to vehicle manufacturer’s
recommendation.
Low hydraulic system pressure (PSI)
Check with pressure gauge. If low, investigate cause.
Material build-up in discharge tube
With vehicle disconnected, lift discharge rubber flap to check
for build-up within tube. Clean out as necessary.
Material(s) too large
Reduce material size.
Material dispensing too thin
Run auger continuously in reverse, or thicken material.
Worn motor seal
Replace motor seal.
Damaged hopper
Contact Danuser.
Worn gate seal
Replace gate seal.
Safety grate obstructed
Ensure no material is jammed between safety grate and ears.
For additional assistance, please call your dealer or contact Danuser direct:
Tel: (573) 642-2246
E-mail: [email protected]
20
Maintenance &
Lubrication
Proper servicing and maintenance are key to the long life of any attachment. Careful
inspection and routine maintenance help avoid costly downtime and repair. Do not use the
Mini MAC with any damaged parts.
1WARNING
1 DANGER
Never attempt
adjustments, service,
or repairs while the
equipment is in operation.
Never check pressurized system for leaks with your bare
hand. Wear proper hand and eye protection and use wood
or cardboard when searching for suspected leaks. Oil
escaping from pinhole leaks under pressure can penetrate
skin and create a serious medical emergency. If any fluid
is injected into the skin, gangrene, blood poisoning, even
death may result. Obtain medical attention immediately.
1 DANGER
1WARNING
Never allow anyone under
the attachment at any
time.
1 DANGER
Never work under
equipment supported
by hydraulics. Even
with the vehicle shut off,
equipment can suddenly
drop if controls are
actuated or if hydraulic
lines burst.
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
Do not modify the attachment. Modifications may weaken
the integrity of the attachment and may impair the safety,
function, life, and performance of the Mini MAC.
1CAUTION
When making repairs or servicing the Mini MAC, use only
parts that meet the original equipment manufacturer’s
standards and requirements.
Maintenance
Inspect the attachment for any damage, worn parts, or
cracked welds. Repair or replace as necessary.
Check for damaged or missing safety signs. Replace as
necessary.
Check all fasteners. Ensure they are tight and secure.
(See Torque Values Chart.) Replace as necessary.
Check all hydraulic components for leaks or wear.
Repair or replace as necessary.
Interval
Before each use
Before each use
Daily
Daily
Lubrication Point
Motor Mounting Plate - 1 Zerk
Add multi-purpose grease until
grease emerges
Every
10
Hours
21
Service
Recommended Tools
Replacing Rubber Flight
•
•
•
1 DANGER
The Mini MAC is equipped with one (1) rubber flight at the discharge end of the auger. The
flight should only be replaced when performance has been reduced.
Never attempt
adjustments, service,
or repairs while the
equipment is in operation.
1 DANGER
Never allow anyone under
the attachment at any
time.
5/16” punch
Hammer
Chisel
3
•
•
7/16” wrench
Dead-blow hammer or mallet
Use genuine Danuser replacement parts only. Substitute parts may not meet
standards required for safe, dependable operation.
STEP 1:  Lower the Mini MAC onto a flat, level surface.
STEP 2:  Shut off the vehicle engine, relieve all hydraulic pressure, and remove the vehicle
key before leaving the vehicle operator station.
STEP 3:  Open the safety grate.
STEP 4:  Using a 5/16” punch and hammer, remove the roll pin in the auger collar.
1 DANGER
Never work under
equipment supported
by hydraulics. Even
with the vehicle shut off,
equipment can suddenly
drop if controls are
actuated or if hydraulic
lines burst.
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1 CAUTION
Always use two people to
handle heavy, unwieldy
components during
assembly, installation,
maintenance, service,
removal, or movement of
the attachment.
22
STEP 5:  Close the gate on the discharge end by lifting on the handle and rotating it to the
left or the right. Once closed, lower the handle and ensure it locks into one of the
slots in the latch plate.
STEP 6:  Slide the auger away from the motor until the collar clears the shaft.
STEP 7:  Pull up and slide the auger toward the motor end of the bucket until the auger is
free of the discharge tube.
Service
Replacing Rubber Flight
(continued)
STEP 8:  Place the auger on a secure work platform. Use a hammer and chisel to remove the
lock nuts from the flight.
STEP 9:  Using the supplied hardware and a 7/16” wrench, replace the worn rubber flight.
The wear face should be installed toward the discharge end of the bucket.
Wear Face
Belting
Service
Replacing Rubber
Gate Seal
1 DANGER
Never attempt
adjustments, service,
or repairs while the
equipment is in operation.
1 DANGER
Never allow anyone under
the attachment at any
time.
1 DANGER
Recommended Tools
•
•
Hammer
Chisel
•
•
7/16” wrench
3/4” wrench
The Mini MAC is equipped with one (1) rubber seal at the discharge end of the auger. The
disc should only be replaced when performance has been reduced.
3
Use genuine Danuser replacement parts only. Substitute parts may not meet
standards required for safe, dependable operation.
STEP 1:  Lower the Mini MAC onto a flat, level surface.
STEP 2:  Shut off the vehicle engine, relieve all hydraulic pressure, and remove the vehicle
key before leaving the vehicle operator station.
STEP 3:  Remove the one (1) klik pin and lift the discharge rubber flap at the discharge end
of the bucket.
STEP 4:  Open the gate on the discharge end by lifting on the handle and rotating it to the
left or the right. Rotate the gate until the heads of the two (2) 1/2” bolts can be
accessed.
Never work under
equipment supported
by hydraulics. Even
with the vehicle shut off,
equipment can suddenly
drop if controls are
actuated or if hydraulic
lines burst.
STEP 5:  Using a 3/4” wrench, remove the two (2) bolts holding the gate seal and plate to
the shaft.
STEP 6:  Remove the gate seal and plate assembly from the bucket.
STEP 7:  Using a 7/16” wrench or a hammer and a chisel, remove the 8 nuts and bolts
holding the gate seal to the plate.
23
Service
Replacing Rubber
Gate Seal
(continued)
STEP 8:  Using the supplied hardware and a 7/16” wrench, replace the worn rubber gate
seal. The wear face should be installed toward the plate.
Wear Face
Belting
1 WARNING
Personal protection
equipment including
hard hat, safety glasses,
safety shoes, gloves,
and hearing protection
are recommended during
assembly, installation,
operation, maintenance,
service, removal,
or movement of the
attachment.
1 CAUTION
Always use two people to
handle heavy, unwieldy
components during
assembly, installation,
maintenance, service,
removal, or movement of
the attachment.
24
STEP 9:  Reinstall the gate seal and plate assembly into the bucket using the supplied
hardware and a 3/4” wrench. The rubber seal should be closest to the shaft.
STEP 10:  Check the range of motion of the newly installed gate.
STEP 11:  Close the discharge rubber flap and secure it with one (1) klik pin.
Torque Values
Chart
Torque Values Chart
Bolt Head Identification
Bolt Size
(inches)
Grade 2
Grade 5
Bolt Head Identification
Grade 8
ASTM A574
5.8
8.8
Class 5.8
Nm
ft.-lb.
Nm
4
3
6
in tpi
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
mm x pitch
1/4” 20
7.4
5.6
11
8
16
12
19
14
M5 x 0.8
10.9
8.8
Bolt Size
(Metric)
Class 8.8
12.9
10.9
12.9
Class 10.9
Class 12.9
ft.-lb.
Nm
ft.-lb.
Nm
ft.-lb.
5
9
7
11
8
1/4” 28
8.5
6
13
10
18
14
22
16
M6 x 1
7
5
11
8
15
11
18
13
5/16” 18
15
11
24
17
33
25
39
29
M8 x 1.25
17
12
26
19
36
27
42
31
5/16” 24
17
13
26
19
37
27
43
32
M8 x 1
18
13
28
21
39
29
46
34
3/8” 16
27
20
42
31
59
44
69
51
M10 x 1.5
33
24
52
39
72
53
84
62
3/8” 24
31
22
47
35
67
49
79
58
M10 x 0.75
39
29
61
45
85
62
98
72
7/16” 14
43
32
67
49
95
70
110
81
M12 x 1.75
58
42
91
67
125
93
148
109
7/16” 20
49
36
75
55
105
78
123
91
M12 x 1.5
60
44
95
70
130
97
153
113
1/2” 13
66
49
105
76
145
105
168
124
M12 x 1
90
66
105
77
145
105
167
123
1/2” 20
75
55
115
85
165
120
190
140
M14 x 2
92
68
145
105
200
150
235
173
9/16” 12
95
70
150
110
210
155
235
173
M14 x 1.5
99
73
155
115
215
160
254
187
9/16” 18
105
79
165
120
235
170
262
193
M16 x 2
145
105
225
165
315
230
365
269
5/8” 11
130
97
205
150
285
210
323
238
M16 x 1.5
155
115
240
180
335
245
388
286
5/8” 18
150
110
230
170
325
240
366
270
M18 x 2.5
195
145
310
230
405
300
504
372
3/4” 10
235
170
360
265
510
375
574
423
M18 x 1.5
220
165
350
260
485
355
561
414
3/4” 16
260
190
405
295
570
420
640
472
M20 x 2.5
280
205
440
325
610
450
712
525
7/8” 9
225
165
585
430
820
605
925
682
M20 x 1.5
310
230
650
480
900
665
1052
776
7/8” 14
250
185
640
475
905
670
1020
752
M24 x 3
480
355
760
560
1050
780
1231
908
1” 8
340
250
875
645
1230
910
1386
1022
M24 x 2
525
390
830
610
1150
845
1337
986
1” 12
370
275
955
705
1350
995
1555
1147
M30 x 3.5
960
705
1510
1120
2100
1550
2447
1805
1-1/8” 7
480
355
1080
795
1750
1290
1971
1454
M30 x 2
1060
785
1680
1240
2320
1710
2706
1996
1-1/8” 12
540
395
1210
890
1960
1440
2202
1624
M36 x 3.5
1730
1270
2650
1950
3660
2700
4272
3151
M36 x 2
1880
1380
2960
2190
4100
3220
5095
3758
1-1/4” 7
680
500
1520
1120
2460
1820
2771
2044
1-1/4” 12
750
555
1680
1240
2730
2010
3068
2263
1-3/8” 6
890
655
1990
1470
3230
2380
3638
2683
1-3/8” 12
1010
745
2270
1670
3680
2710
4143
3056
1-1/2” 6
1180
870
2640
1950
4290
3160
4823
3557
1-1/2” 12
1330
980
2970
2190
4820
3560
5426
4002
KEY:
in tpi = nominal thread diameter in inches threads per inch
Nm = Newton-meter
ft.-lb. = foot pounds
mm x pitch = nominal thread diameter in millimeters by thread pitch
Torque tolerance +0%, -15% of torque values. Unless otherwise specified, use torque values listed above.
25
Parts
2 CALIFORNIA WARNING
This product can expose you to chemicals including lead, which are
known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
16
29
28
27
25 24
26
23
17
21
30
31
15
22
19
14 13 12 11
20
32
10
9
8
7
33
6
4
1
34
18
26
35
2
3
5
Parts
(continued)
REF. NO.
PART NO.
DESCRIPTION
QTY.
1
2
3
4
5
6
230470S
21156
933
7637
256026
176033
Universal Mini Hopper (Includes Decals & Safety Signs)
Flat Washer (1/2”)
Hex Cap Screw (1/2"–13 x 1.75", Gr. 5)
Klik Pin Assembly
Discharge Rubber Flap
Drive Rivet
1
8
4
1
1
4
7
8
230458
230446
Gate Seal Kit
Gate Seal Rod
1
1
9
10
11
12
13
230447
186060
230448S
1054
246135
Plate
Handle Grip
Handle (Includes REF. NO. 11)
Flat Washer (5/8”)
Shoulder Bolt (1/2"–13, Ø 5/8" x 1/2" L)
1
1
1
1
1
14
15
16
17
18
19
20
1533
11019
230490
230485
*230469
230493
10125
Klik Pin Assembly
Chute - 24”
Safety Grate
Auger Assembly
Mini Auger Rubber Replacement Kit
Tube
Toplock Nut (1/2”–13)
1
1
1
1
1
4
8
21
22
23
24
25
26
27
28
246004
246005
230441
230440
11038
230442
10040
206031
2
2
1
1
1
1
2
1
29
30
31
32
33
34
35
10048
10049
246008
246002
246029
21056
21258
Carriage Bolt (1/2”–13 x 4”, Gr. 5)
Carriage Bolt (1/2”–13 x 3.5”, Gr. 5)
Seal Retaining Plate
Seal
Roll Pin (3/8” x 2”)
Hub
Adapter, 45° (#10 JIC M to #10 ORB M)
1/2” Hose Assembly Kit (#10 JIC F to #10 ORB M)
(Includes two hoses)
Male Coupler (1/2” flush-face, ISO 16028)
Female Coupler (1/2” flush-face, ISO 16028)
Hydraulic Motor
Set Screw (5/16”–18 x 1/2”)
Grease Fitting, 45°
Flat Washer (1/4”)
Operator’s Manual Canister
1
1
1
1
1
2
1
* Not included with base model.
27
Parts
Bob-Tach® Mount Kit
2
2 CALIFORNIA WARNING
This product can expose you to chemicals including lead, which are
known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
3
4
1
28
REF. NO.
PART NO.
DESCRIPTION
QTY.
1
2
3
4
230435
12245
21156
10125
Bob-Tach® Quick Attach Plate
Hex Cap Screw (1/2”–13 x 1.5”, Gr. 5)
Flat Washer (1/2")
Toplock Nut (1/2"–13)
1
6
12
6
Accessories
2 CALIFORNIA WARNING
This product can expose you to chemicals including lead, which are
known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
Chute - 24”
PN 11019 - Chute can be linked
to extend length.
Bob-Tach® Mount Kit
PN 230434 - Allows Mini MAC to be
mounted to Bob-Tach® machines. Includes
quick attach plate and mounting hardware.
29
Warranty
DANUSER
LIMITED WARRANTY
Model #
Serial #
Danuser Machine Company, LLC (“Danuser”) warrants its products, under normal use and maintenance, to be free from defects in
material and workmanship for period(s) specified below from the purchase date from an authorized Danuser Dealer. Start of the
warranty period is determined by purchase date given on your returned WARRANTY REGISTRATION FORM. Proof of purchase
may be required. This Limited Warranty is extended only to the original purchaser of Danuser products.
Mini MAC - 1 Year
Wear Items Not Covered Under Warranty - Hydraulic Hoses, Seals, and Auger Flighting
1.
During the applicable warranty period, Danuser, at its option, will repair or replace any part determined by Danuser to be
defective. Such repair or replacement shall take place at Danuser’s factory or a location designated by Danuser. Under no
circumstances shall Danuser be obligated for the cost of any repair or replacement by anyone other than Danuser without its
express written consent.
2.
Parts may not be returned without written authorization from Danuser.
3.
Some purchased components, including but not limited to hydraulic components, are subject to the inspection and warranty of
the respective manufacturer. Thus, delays in a warranty determination can be expected while Danuser awaits their decision.
4.
This warranty is void if any attempt is made to make field repairs to hydraulic components. To qualify for warranty inspection,
the “failed” part(s) must be returned in its original “failed” condition.
5.
To make a claim under this warranty, you may either contact your authorized Danuser Dealer or initiate a claim directly with
Danuser. In either case, a Warranty Claim Form must be completed and written authorization from Danuser obtained prior
to returning parts. All warranty claims must include detailed information regarding make and model of vehicle on which the
Danuser product was mounted, hours of use, description of events that led up to the failure, and any other information helpful
in reviewing the warranty claim. All warranty returns must be prepaid. Shipments arriving at our factory on a freight collect
basis will be refused by our receiving department. The freight charge will be credited if the parts are determined by Danuser to
be defective, and the associated freight costs in returning those parts will be prepaid by Danuser. NOTE: Hydraulic components
must arrive with all ports sealed from dirt and moisture. If a hydraulic component arrives with open ports, the warranty is void
and no inspection will be made.
6.
Products or parts thereof, which, as determined by Danuser’s examination, show wear from normal use, have been improperly
operated, damaged by accident or negligence, field repaired, altered or modified are not considered defective in material and
workmanship and are not covered by this warranty. This warranty does not apply to parts subject to normal wear ("Wear
Items") or to damage caused by the failure to perform recommended maintenance or to replace worn parts. This warranty shall
not obligate Danuser to bear any cost of labor for field repair, replacement, testing, or adjustment nor for damage caused by
accident, abuse, misuse, or environmental elements.
7.
Any parts or labor required to repair or replace parts not covered under this warranty will be charged to the customer. Parts
repaired or replaced by Danuser are then covered by this warranty only for the remainder of the original warranty as if such
parts were original parts.
8.
Danuser reserves the right to change its specifications and designs at any time.
This warranty is exclusive and in lieu of all other express warranties, if any, including the implied warranties of merchantability and
fitness for a particular purpose. It shall not extend beyond the duration of the expressed warranty provided herein and the remedy
for violations of any implied warranty shall be limited to repair or replacement of the defective part pursuant to the terms contained
herein. No employee, dealer, salesman, or representative is authorized to change this warranty in any way or grant any other warranty.
Danuser shall not be liable for any consequential, incidental, or punitive damages, losses, or expenses, including those resulting from
or caused by any defects.
Danuser Machine Company, LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel:
(573) 642-2246
E-mail:
[email protected]
Website: www.danuser.com
PD 5146
">