Lowrance Eagle Eye 9 Operator Manual

EAGLE EYE™
Operator manual
ENGLISH
www.lowrance.com
Preface
Copyright
© 2026 Navico Group. All Rights Reserved. Navico Group is a division
of Brunswick Corporation.
Trademarks
®Reg. U.S. Pat. & Tm. Off, and ™ common law marks. Visit
www.navico.com/intellectual-property to review the global
trademark rights and accreditations for Navico Group and other
entities.
• Navico® is a trademark of Navico Group.
• Lowrance® is a trademark of Navico Group.
• AutoTrack™ is a trademark of Navico Group.
• DownScan Imaging™ is a trademark of Navico Group.
• DownScan Overlay® is a trademark of Navico Group.
• Easy Routing™ is a trademark of Navico Group.
• FishReveal™ is a trademark of Navico Group.
• Genesis® is a trademark of Navico Group.
• Navionics® is a trademark of Navionics S.r.l.
• NMEA® and NMEA 2000® are trademarks of the National Marine
Electronics Association.
• SD® and microSD® are trademarks of SD-3C, LLC.
Safety, disclaimer and compliance
This product's safety, disclaimer and compliance statements are
supplied as a separate document.
Warranty
This product’s warranty is supplied as a separate document.
About this manual
This manual is a reference guide for operating the Eagle Eye MFD.
This unit is only capable of the sonar views and frequencies
indicated in the specification included in the transducer’s
installation guide for the transducer provided with the unit.
• Eagle Eye MFD and Eagle Eye transducer are exclusively
compatible.
Preface | Eagle Eye Operator Manual
3
Manual version
This manual is written for the first version of software delivered with
Eagle Eye. The manual is continually updated to match new
software releases. The latest available manual version can be
downloaded from www.lowrance.com.
The software version
The software version currently on this unit can be found in the
About dialog in System Settings dialog.
For information on upgrading your software, refer to "Software updates"
on page 73.
Contact us
For product support and service information, visit
www.lowrance.com/contact-us.
4
Preface | Eagle Eye Operator Manual
Contents
9
Introduction
9
10
11
13
Front controls
The Home page
Application pages
Device registration
14 Basic operation
14
14
15
15
15
16
16
17
Turning the system on and off
System Controls dialog
Standby mode
Display illumination
Using menus and dialogs
Using the cursor on the panel
MOB waypoint
Screen capture
18 Customizing your system
18
18
19
21
Customizing the Home page wallpaper
Data overlay
Custom pages
Adjusting the split on multiple panel pages
22 Charts
22
22
23
23
23
23
23
23
24
24
25
27
28
32
The Chart panel
Chart data
Selecting chart type
Vessel symbol
Chart scale
Panning the chart
Waypoints, routes, and trails
Navigating
Displaying information about chart items
Find objects on chart panels
More options
C-MAP charts
Navionics® charts
Chart settings
Contents | Eagle Eye Operator Manual
5
34 Waypoints, routes, and trails
34
35
36
40
Dialogs
Waypoints
Routes
Trails
43 Navigating
43
43
43
44
44
44
About navigating
Menu options
Navigate to cursor position
Navigate to a waypoint
Navigate a route
Navigation settings
46 Sonar
46
46
47
47
47
48
49
49
51
53
The Sonar image
Zooming the image
Using the cursor on the image
Viewing history
Start recording sonar log data
Viewing the recorded sounder data
Customize the image settings
Custom and Ice Fishing mode options
More options
Sonar settings
55 Live Sonar
55
55
55
56
56
56
57
59
About Live Sonar
Live Sonar forward panel
Live Sonar down panel
Zooming the image
Using the cursor on the panel
Recording Live Sonar video
Modes and image settings
More Options
60 DownScan
60
6
About DownScan
Contents | Eagle Eye Operator Manual
60
60
60
61
61
61
The DownScan panel
Zooming the DownScan image
Using the cursor on the DownScan panel
Viewing DownScan history
Recording DownScan data
Customize the image settings
65 Alarms
65
65
65
65
66
Alarm system
Type of messages
Alarm messages
Acknowledging a message
Alarms dialog
67 Tools
67
70
70
70
Settings
Waypoints/routes/trails
Info
Storage
72 Maintenance
72
72
72
72
73
74
76
Preventive maintenance
Cleaning the display unit
Checking the connectors
Service assistant
Software updates
Backing up your system data
Importing backed up files
77 Simulator
77
77
78
Retail mode
Simulator source files
Advanced simulator settings
Contents | Eagle Eye Operator Manual
7
8
Contents | Eagle Eye Operator Manual
1
Introduction
Front controls
A
Pages
• Press to activate the home page.
B
Waypoint
• Press to open the new waypoint dialog.
• Press twice to save a waypoint.
• Press and hold to access the find dialog.
C
Arrows
• On any full screen page:
- Press to position the cursor.
- Press to pan the image in any direction.
• On multi-panel pages:
- Press to select a panel.
• In menus and dialogs:
- Press to navigate.
D
Exit
• On a maximized, multi-panel page:
- Press to return to the multi-panel page.
• In menus and dialogs:
- Press to return to previous menu level and to exit a
dialog.
Introduction | Eagle Eye Operator Manual
9
E
Enter
• On multi-panel pages:
- Press to maximize the selected panel.
• In menus and dialogs:
- Press to confirm a selection.
F
Zoom
• Press to zoom the image.
• Press both keys together to create a MOB (Crew
Overboard) waypoint at your position.
G
Menu
• Press to display the menu on full screen pages.
H
Power
• Press once to display the System Controls dialog.
• Press ad hold to power the unit ON/OFF.
• Repeat short presses to cycle the backlight brightness.
Micro SD card
The card reader is located on the right side of the unit.
The Home page
The Home page is accessed from any operation by a short press on
the Pages key.
Ú Note: Page icons on the Home page vary with model type.
10
Introduction | Eagle Eye Operator Manual
1
Tools panel - Select a button to access dialogs used for
carrying out a task, or for browsing stored information.
2
Application page icons - Select a button to display the
application page.
3
Customize - Activate customize mode to delete or modify
custom pages.
Application pages
1
2
3
4
5
1
Application panel
2
Menu - Panel specific menu.
3
System Controls dialog - Quick access to basic system
settings.
4
Dialog - Information input from the user.
Introduction | Eagle Eye Operator Manual
11
5
Alarm message - Displayed if dangerous situations or
system faults occur.
Each application connected to the system is presented on panels.
The application can be presented as a full page, or in combination
with other panels in a multiple panel page.
All application pages are accessed from the Home page.
Custom pages
The system is delivered with three preconfigured custom pages
including one for Down Live and one for Forward Live. These two
pages cannot switch between the down and forward modes, and
the menu option is not present.
You can create your own custom pages including live sonar pages
that can switch between Down Live and Forward Live. To add a
custom page, refer to "Adding new custom pages" on page 19.
To edit or delete a custom page, refer to "Edit or delete custom pages" on
page 20.
Multiple panel custom pages
You can have up to 4 panels on a custom page. Refer to "Adding new
custom pages" on page 19.
2 panels page
3 panels page
4 panels page
Panel sizes in a multiple panel page can be adjusted from the
System Controls dialog. Refer to "Adjusting the split on multiple panel pages"
on page 21.
• With the cursor not active on any panel, switch active panel by
using the Arrow keys. An active panel is indicated with an orange
border.
• Maximize the active panel by pressing the Enter key. Press the
Exit key to go back to the multiple panel page.
• To display the panel menu, it must first be maximized. Once
maximized, press the Enter key (again) to display the menu for
12
Introduction | Eagle Eye Operator Manual
the maximized pane. Press the Exit key to close the menu, press
the Exit key again to go back to the multiple panel page.
• Activate the cursor on the active or maximized panel by pressing
the Arrow keys, then use the Arrow keys to position the cursor.
Press the Exit key to remove the cursor.
Device registration
You are prompted to register your device during startup. You can
also register by selecting the register option in the System settings
dialog. Registration can be done:
• From a smart device with internet access
• By calling
Introduction | Eagle Eye Operator Manual
13
2
Basic operation
Turning the system on and off
The system is turned on by pressing the Power key.
Press and hold the Power key to turn the unit off.
If the key is released before the shut-down is completed, the power
off process is cancelled.
You can also turn the unit off from the System Controls dialog.
First time startup
When the unit is started for the first time, or after a reset, the unit
displays a series of dialogs. Respond to the dialog prompts to make
fundamental settings.
You can perform further setup and later change settings using the
system settings dialogs.
System Controls dialog
The System Controls dialog provides quick access to basic system
settings. You display the dialog by making a short press on the
Power key.
The icons displayed on the dialog can vary. For example, the adjust
splits option is only available if you are viewing a multiple panel
page when you open the System Controls dialog.
Activating functions
Select the icon of the function you want to set or toggle on or off.
For those functions that toggle on and off, an orange bar across the
top of the icon indicates the function is activated, as shown in the
Data overlay and Stop sonar icons above.
14
Basic operation | Eagle Eye Operator Manual
Standby mode
In Standby mode, the Sonar and the backlight for the screen are
turned off to save power. The system continues to run in the
background.
You select Standby mode from the System Controls dialog.
Switch from Standby mode to normal operation by a short press on
the Power key.
Display illumination
Brightness
You can cycle the preset backlight levels by short presses on the
Power key.
The display backlighting can also be adjusted from the System
Controls dialog.
Night mode
The night mode can be activated from the System Controls dialog.
The night mode option optimizes the color palette for low light
conditions.
Using menus and dialogs
Menus
The menu is used to operate the system and to adjust settings.
Press the Menu key to display the page menu. Press the Menu key
again to close the menu.
Use the Arrow keys to highlight a menu option, then press the Enter
key to confirm the selection.
Scroll bars - activate the scroll bar in the menu and use the Arrow
keys to adjust it. Press the Enter key to save your adjustment.
The status of the cursor (active vs. inactive) changes the menu
options.
Dialog boxes
Use the Arrow keys to highlight a dialog option, then press the
Enter key to confirm the selection.
Basic operation | Eagle Eye Operator Manual
15
Numeric and alphanumeric keyboards are automatically displayed
when required for entering user information in dialogs.
A dialog is closed by saving or cancelling the entry. A dialog can
also be closed by pressing the Exit key.
Using the cursor on the panel
The cursor can be used to measure a distance, to mark a position,
and to select items.
By default, the cursor is not shown on the panel.
When the cursor is active, the cursor position window is displayed.
MOB waypoint
If an emergency situation should occur, you can save a crew
overboard (MOB) waypoint at the vessel’s current position.
Create a MOB waypoint
To create a crew overboard (MOB) waypoint:
• Simultaneously press the Zoom In (+) and Zoom out (-) keys
When you activate the MOB function, the following actions are
automatically performed:
• A MOB waypoint is created at the vessel’s position
• The display switches to a zoomed chart panel, centered on the
vessel's position
• The system displays navigation information back to the MOB
waypoint
Multiple MOB waypoints can be created. The vessel continues to
show navigation information to the initial MOB waypoint.
Navigation to subsequent MOB waypoints needs to be done
manually.
Delete a MOB waypoint
A MOB waypoint can be deleted from the menu when the MOB is
activated.
16
Basic operation | Eagle Eye Operator Manual
Stop navigating to MOB waypoint
The system continues to display navigational information towards
the MOB waypoint until you cancel the navigation from the menu.
Screen capture
To take a screen capture:
• Simultaneously press the pages key and the power key
Basic operation | Eagle Eye Operator Manual
17
3
Customizing your system
Customizing the Home page wallpaper
The Home page's wallpaper can be customized. You can use your
own picture in .jpg or .png format.
The images can be available on any location that can be seen in the
files browser. When a picture is chosen as the wallpaper, it is
automatically copied to the Wallpaper folder.
Data overlay
You can have data information as overlay on a page.
Turning Data overlay on and off
You can turn overlay data on or off for any active page by selecting
the Data overlay icon on the System Controls dialog. When Data
overlay is on, an orange bar appears above the icon.
Edit overlay data
Use the Edit overlay option on the System Controls dialog to access
edit menu options to:
• Add a new data overlay to the active panel.
• Delete a selected data overlay.
• Change a selected data overlay to display different data.
18
Customizing your system | Eagle Eye Operator Manual
• Configure a selected data overlay appearance (digital or analog,
size, etc.).
• Re-locate an item by selecting and moving it.
Custom pages
Adding new custom pages
A maximum of 9 pages are allowed. You can have up to 4 panels on
a custom page.
1. Select the add page icon on the Home page to open the page
editor dialog.
2. Use the Arrow keys to highlight a panel, then press the Enter
key. The panel is added to the page.
3. (Optional) Repeat step 2 to add additional panels. A maximum
of 4 panels are allowed.
- To change the layout, use the Arrow keys to select the layout
option. Use this option to specify how you want the panels
displayed.
- To remove a panel, use the Arrow keys to select the pane on
the right side of the dialog and to highlight the delete (X) icon
in the top right corner of the panel. Press the Enter key. The
panel is removed from the pane on the right side of the
dialog.
- To move a panel, use the Arrow keys to select the pane on the
right side of the dialog and to highlight the arrows icon in the
top left corner of the panel you want to move. Press the Enter
key. A larger arrows icon is displayed. Use the Arrow keys to
Customizing your system | Eagle Eye Operator Manual
19
move the highlighted panel. Press the Enter key to save your
adjustment.
4. Save the page layout.
The system displays the new custom page, and an icon for the new
page is included on the Home page.
Edit or delete custom pages
1. On the Home page, use the Arrow keys to highlight the
customize option and press the Enter key to turn ON the
customize option.
2. Use the Arrow keys to:
- Select the X option on a custom page icon, and press the
Enter key to remove the page
- Select the tool option on a custom page icon, and press the
Enter key to display the page editor dialog
3. Change the layout, add, and remove panels using the custom
page editor dialog. Refer to Step 3 in "Adding new custom pages" on
page 19.
4. Save or discard your changes to leave edit mode.
20
Customizing your system | Eagle Eye Operator Manual
Adjusting the split on multiple panel pages
1. Open the multiple panel page.
2. Quick-press the Power key to open the System Controls dialog
3. Select the adjust splits option. The cursor arrows icon appears
on the multiple panel page.
4. Use the Arrow keys to move the split to the desired position.
5. Press the Enter key to save the split adjustment.
Customizing your system | Eagle Eye Operator Manual
21
4
Charts
The Chart panel
A
North indicator
B
Vessel
C
Chart range scale
D
Grid lines*
E
Range rings*
* Optional chart items. Optional chart items can be turned on/off
individually from the chart settings dialog.
Chart data
The system can be delivered with preloaded cartography.
For a full selection of supported charts, visit the product web site.
Ú Note: Chart menu options vary depending on the chart you are
using.
Ú Note: The system does not automatically switch to preloaded
cartography if the chart card is removed. A low-resolution chart
will be displayed until you re-insert the card or manually switch
back to the preloaded cartography.
22
Charts | Eagle Eye Operator Manual
Selecting chart type
You specify the chart type in the Chart panel by selecting one of the
available chart types in the chart source menu option.
Vessel symbol
When the system has a valid GPS position lock, the vessel symbol
indicates vessel position. If no GPS position is available, the vessel
symbol includes a question mark.
Chart scale
You zoom in and out on the chart by using the Zoom keys.
Chart range scale and range rings interval (when turned on) are
shown in the lower right corner of the chart panel.
Panning the chart
You can move the chart in any direction by using the Arrow keys to
move the cursor to the edge of the chart panel in the desired
direction.
To remove the cursor and cursor elements from the panel, press the
Cursor/Waypoint key. This also centers the chart to the vessel
position.
Waypoints, routes, and trails
You can position and manage waypoints, routes and trails on the
page. For more information, refer to "Waypoints, routes, and trails" on page
34.
Navigating
You can use the page for navigating to the cursor, to a waypoint, or
navigate a route. Refer to "Navigating" on page 43.
Charts | Eagle Eye Operator Manual
23
Displaying information about chart items
When you position the cursor over a chart item, waypoint, trail or a
route, basic information for the selected item is displayed as a popup.
Ú Note: Pop-up information has to be enabled in chart settings to
see basic item information.
Select the info option in the menu to display a list of items near the
cursor. Select an item in the list to display all available information
for that item.
Find objects on chart panels
Select the find menu option to search for chart items.
24
Charts | Eagle Eye Operator Manual
More options
Chart overlay
You can add overlays on the chart panel.
When an overlay is selected, the chart menu expands to include
basic menu options for the selected overlay.
Information about the overlay menu options are described in more
detail below or in their separate sections in this manual.
Genesis live overlay
Ú Note: Only available when viewing Lowrance or C-MAP chart
source.
Ú Note: A microSD® memory card with available space must be
inserted into the unit before data can be recorded.
Genesis live is a real-time feature where the unit creates an overlay
of depth contour mapping based on live sonar soundings. The
Genesis live sonar soundings are recorded onto and viewed from
the unit's memory card.
If at any time the memory card is removed or runs out of space, the
feature will turn itself off and the option is disabled in the menu.
• The more passes of an area included in the live sonar soundings
log, results in better Genesis live maps.
• Genesis live is accurate up to 20 knots.
• Genesis live can record from a networked transducer.
• The data logging and display is for the unit with the memory
card. Genesis live maps are not shared over the network.
Ú Note: Genesis Live data is not adjusted for tidal offset.
Genesis live menu options
Transparency
Adjusts the transparency of the overlay.
Contour interval
Defines the density of live depth contours shown.
Charts | Eagle Eye Operator Manual
25
Depth palette
Controls the color palette used to color the depth areas.
• Chart sync – syncs the Genesis live layer to the same palette as
the chart depth palette defined in the chart menu (under Chart
options, View, Depth palette). This option also allows custom
palettes to be defined in the chart menu and applied to the
Genesis layer.
• Navigation – uses the navigation palette.
• Depth shading – uses the depth shading palette.
• Paper chart – uses the paper chart palette.
• Safety shading – uses the safety depth setting to shade the color
lower than the set safety depth. Also enables the Safety depth
option on the Genesis live menu.
Safety depth
Sets the safety depth. Areas that are shallower than the safe
minimum depth are shaded. This option is only available if the
Safety shading palette is selected.
Chart orientation
You can specify how the chart is rotated in the panel. The chart
orientation symbol in the panel’s upper right corner indicates the
north direction.
North up
Course up
North up
Displays the chart with north upward.
Course up
The chart direction depends on if you are navigating:
• When navigating, the desired course line is oriented up.
26
Charts | Eagle Eye Operator Manual
• When not navigating, the direction the vessel is actually traveling
(COG) is oriented up.
Look ahead
Moves the vessel icon on the panel to maximize your view ahead of
the vessel.
C-MAP charts
All possible menu options for C-MAP charts are described below.
The features and menu options available can vary depending on the
charts you use. This section shows menus from a C-MAP chart.
Ú Note: A menu option is greyed out if the feature is not available
on the chart displayed.
C-MAP specific chart options
Chart detail
• Full - displays all available information for the chart in use.
• Medium - displays minimum information sufficient for
navigation.
• Low - displays basic level of information that cannot be removed,
and includes information that is required in all geographic areas.
It is not intended to be sufficient for safe navigation.
Genesis Layer
The Genesis Layer displays high-resolution contours contributed by
Genesis users that have passed a quality check.
This option toggles the Genesis layer on/off on the chart image.
Available only if the C-MAP chart contains Genesis Layer data.
Depth palette
Controls the Depth palette used on the map.
Depth filter
Filters out depth values shallower than the selected depth filter
limit.
Charts | Eagle Eye Operator Manual
27
Safety depth
Charts use different shades of colors to distinguish between shallow
and deep water. After enabling the safety shading depth palette,
specify the desired safety depth limit and the color/shading for
different depths.
Chart categories
Several categories and sub-categories are included. You can turn
on/off the categories individually depending on which information
you want to see.
Navionics® charts
Some Navionics® features require the most current data from
Navionics®. For those features, a message is displayed stating that
the feature is unavailable if you do not have the appropriate
Navionics® charts or chart card inserted. For more information on
what is required for these features, refer to www.navionics.com.
You can also get a message if you try to use a restricted feature
when the Navionics® chart card is not activated. To activate the card,
contact Navionics®.
28
Charts | Eagle Eye Operator Manual
Navionics specific chart options
Chart overlay, orientation, and look ahead options (previously
described in this section) are common to both C-MAP and
Navionics charts. The following describe Navionics specific chart
options.
Community edits
Toggles on the chart layer including Navionics® edits. These are user
information or edits uploaded to Navionics® Community by users,
and made available in Navionics® charts.
For more information, refer to Navionics® information included with
your chart, or to Navionics® website: www.navionics.com.
SonarChart
The system supports the Navionics® SonarChart feature.
SonarChart displays a bathymetry map showing high resolution
contour detail and standard navigational data. For more
information, refer to www.navionics.com.
SonarChart Live
SonarChart Live is a real-time feature where the device creates an
overlay of depth contours based on your own live sonar soundings.
When you select SonarChart Live overlay the menu expands to
display SonarChart Live options.
Transparency
The SonarChart Live overlay is drawn on top of other chart data. The
chart data is completely covered at minimum transparency. Adjust
the transparency to allow the chart details to be seen.
Minimum depth
Adjusts what SonarChart Live rendering treats as the safety depth.
This affects the coloring of the SonarChart Live area. As the vessel
approaches the safety depth, the SonarChart Live area will gradually
change from a simple grey/white to red.
SCL History
Select to display previously recorded data on the chart overlay.
Charts | Eagle Eye Operator Manual
29
Ú Note: SonarChart live does not record while SCL history files are
being viewed.
SC Density
Controls the density of the SonarChart and SonarChart Live
contours.
Navionics® Dynamic tides and current icons
Shows tides and currents with a gauge and an arrow instead of the
diamond icons used for static tides and current information.
The tide and current data available in Navionics® charts are related
to a specific date and time. The system animates the arrows and/or
gauges to show the tides and currents evolution over time.
Dynamic tide information
Dynamic current information
The following icons and symbology are used:
Current speed
The arrow length depends on the rate, and the symbol is rotated
according to flow direction. Flow rate is shown inside the arrow
symbol. The red symbol is used when current speed is increasing,
and the blue symbol is used when current speed is decreasing.
Tide height
The gauge has 8 labels and is set according to absolute max/min
value of the evaluated day. The red arrow is used when tide is rising,
and the blue arrow is used when tide is falling.
Ú Note: All numeric values are shown in the relevant system units
(unit of measurement) set by user.
Easy View
Magnifying feature that increases the size of chart items and text.
30
Charts | Eagle Eye Operator Manual
Ú Note: There is no indication on the chart showing that this
feature is active.
Fishing range
Select a range of depths between which Navionics® fills with a white
color.
This allows you to highlight a specific range of depths for fishing
purposes. The range is only as accurate as the underlying chart data,
meaning that if the chart only contains 5 meter intervals for contour
lines, the shading is rounded to the nearest available contour line.
No Depth highlight range
Depth highlight range: 6 m - 12 m
Shallow water highlight
This highlights areas of shallow water between 0 and the selected
depth (up to 10 meters/30 feet).
No shallow water highlighted
Shallow water highlight: 0 m - 3 m
Presentation type
Displays marine charting information such as symbols, colors of the
navigation chart and wording for either International or U.S.
presentation types.
Charts | Eagle Eye Operator Manual
31
Safety depth
The Navionics® charts use different shades of blue to distinguish
between shallow and deep water.
Safety depth, based on a selected limit, is drawn without blue
shading.
Ú Note: The built in Navionics® database features data down to 20
m, after which it is all white.
Chart details
Provides you with different levels of geographical layer information.
Chart settings
Select the settings option in the System Controls dialog to access
the chart settings dialog.
Chart source
Change chart source if a chart card is inserted.
Popup information
Determines whether basic information for panel items is displayed
when you select the item.
Range rings
The range rings can be used to present the distance from your
vessel to other panel objects.
32
Charts | Eagle Eye Operator Manual
The range scale is set automatically by the system to suit the panel
scale.
Grid lines
Turns on/off viewing of longitude and latitude grid lines on the
panel.
Waypoints, Routes, Trails
Turns on/off displaying these items on panels.
Course extension line
Turns on/off displaying the Course Over Ground (COG) extension
line on the panel. The COG is based on information from the GPS.
Extension line length
When the course extension option is turned on, specify the length
of the line to be displayed.
SonarChart Live tide correction
When selected, the tide correction feature uses information from
nearby tide stations (if available) to adjust the depth values used by
SonarChart Live as the sonar is recorded.
Charts | Eagle Eye Operator Manual
33
5
Waypoints, routes, and trails
Dialogs
The Waypoints, Routes, and Trails dialogs give access to advanced
edit functions and settings for these items.
The dialogs are accessed from the Tools panel on the Home page.
Press the menu key to access additional options.
Waypoint options
34
Routes options
Waypoints, routes, and trails | Eagle Eye Operator
Manual
Trails options
Waypoints
A waypoint is a user-generated mark positioned on the chart panel.
Each waypoint has an exact position with latitude and longitude
coordinates. A waypoint is used to mark a position you may later
want to return to. Two or more waypoints can also be combined to
create a route.
Saving waypoints
Press and hold the Waypoint key to save a new waypoint.
• With the cursor inactive, the waypoint is placed at the vessel's
position.
• With the cursor active, the waypoint is placed at the cursor
position.
Moving a waypoint
1. Activate the cursor and maneuver it with the Arrow keys so that
it is over the waypoint.
2. Activate the menu and select the waypoint in the menu. The
menu expands to include the move option.
3. Select the move option in the menu.
4. Use the Arrow keys to move the waypoint to the new position.
5. Press the Enter key.
The waypoint is saved at the new position.
Edit a waypoint
You can edit all information about a waypoint from the Edit
Waypoint dialog.
The dialog is activated by positioning the cursor over the waypoint,
selecting the waypoint in the menu, and then the Edit menu option.
The dialog can also be accessed by activating the Waypoints,
Routes, Trails dialog on the tools panel on the Home page. Select
the Waypoints tab and then the waypoint you want to edit.
Waypoints, routes, and trails | Eagle Eye Operator Manual
35
Delete a waypoint
You can delete a waypoint from the Edit Waypoint dialog or by
selecting the Delete menu option when the waypoint is activated.
The Edit Waypoint dialog is activated by positioning the cursor over
the waypoint, selecting the waypoint in the menu, and then the
delete menu option.
The Edit Waypoint dialog can also be accessed by activating the
Waypoints, Routes, Trails dialog on the tools panel on the Home
page. Select the Waypoints tab, the waypoint you want to delete
and then the delete option.
You can delete MOB waypoints the same way.
Waypoint alarm settings
You can set an alarm radius for each individual waypoint you create.
The alarm is set in the Edit Waypoint dialog.
Ú Note: The waypoint radius alarm must be toggled ON in the
alarm dialog to activate an alarm when your vessel comes
within the defined radius. For more information, refer to "Alarms
dialog" on page 66.
Routes
A route consists of a series of routepoints entered in the order that
you want to navigate them.
When you select a route on the panel it turns green, and the route
name is displayed.
36
Waypoints, routes, and trails | Eagle Eye Operator
Manual
Creating a new route on the page
1. Select the new route option from the menu.
2. Use the Arrow keys to position the cursor at the first routepoint
on the panel.
3. Press the Enter key to create the routepoint.
4. Repeat steps 3 and 4 to continue positioning new routepoints
on the panel until the route is completed.
5. Press the Exit key when completed and save the route.
Edit a route from the panel
You can edit a route by placing the cursor over the route and then
selecting the route in the menu. Select the edit option in the menu.
This opens the Edit route dialog.
The dialog can also be accessed by activating the Waypoints,
Routes, Trails dialog on the tools panel on the Home page. Select
the Route tab and then the route you want to edit.
To edit the route from the panel:
1. Maneuver the cursor over the route in the panel. The route popup is displayed.
2. Press the Enter key and use the Arrow keys to select the route in
the menu. The menu expands with additional options.
- The edit option allows you to move and remove routepoints
on the panel.
- The details option opens the edit route dialog where you can
set route options, rename and manage details.
Waypoints, routes, and trails | Eagle Eye Operator Manual
37
3. Use the Arrow keys to select the option you want to use and
press the Enter key.
4. Follow the prompts to make changes and save your changes.
Delete a route
You can delete a route by selecting the Delete menu option when
the route is activated.
You can also delete routes from the Routes dialog. Refer to "Dialogs"
on page 34.
Creating routes using existing waypoints
You can create a new route by combining existing waypoints from
the New Routes dialog.
The dialog is activated by selecting the route tab in the dialog
displayed when you select the Waypoint, Routes, and Trails tool on
the Home page. Next, select the New route option.
You can also insert existing waypoints in an existing route from the
Edit Routes dialog.
From the Edit Routes dialog, select the routepoint in the list where
you want to insert the waypoint and press the Menu/Enter key.
38
Waypoints, routes, and trails | Eagle Eye Operator
Manual
Converting trails to routes
You can convert a trail to a route from the Edit Trail dialog. The
dialog is activated by activating the trail, then selecting the trail's
pop-up, or the Trail menu option.
The Edit Trail dialog can also be accessed by selecting the
Waypoints tool on the Home page.
The Edit Route dialog
You can add and remove routepoints, and change route properties
using the Edit Route dialog.
This dialog is activated by placing the cursor over the route and
selecting the route in the menu.
The dialog can also be accessed by selecting the route tab in the
dialog displayed when you select the Waypoint, Routes, and Trails
tool on the Home page.
Waypoints, routes, and trails | Eagle Eye Operator Manual
39
Select the name field to change the name. Turn on Display to show
the route on the panel.
Trails
Trails are a graphical presentation of the historical path of the vessel,
allowing you to retrace where you have travelled.
Trails can be converted to routes from the Edit Trails dialog. Refer to
"Converting trails to routes" on page 39.
From the factory, the system is set to automatically track and draw
the vessel's movement on the panel. The system continues to
record the trail until the length reaches the maximum points, and
then automatically begins overwriting the oldest points.
40
Waypoints, routes, and trails | Eagle Eye Operator
Manual
The automatic tracking function (record) can be turned off from the
Edit Trails dialog.
Creating new Trails
You can start a new trail from the Trails dialog, activated by using
the Waypoints, Routes, Trails tool on the Home page and selecting
the Trails tab.
Trails settings
Trails are made up of a series of points connected by line segments
whose length depends on the frequency of the recording.
You can select to position trail points based on time settings,
distance, or by letting the system position a trail point automatically
when a course change is registered.
Ú Note: The Trails option must also be turned ON in the panel
settings dialog to be visible.
Waypoints, routes, and trails | Eagle Eye Operator Manual
41
Coloring trails
To color trails:
• Select the trail in the Trails dialog and set the color for the entire
trail in the Edit Trail dialog.
42
Waypoints, routes, and trails | Eagle Eye Operator
Manual
6
Navigating
About navigating
The navigation function included in the system allows you to
navigate to the cursor position, to a waypoint, or along a predefined
route.
For information about positioning waypoints and creating routes,
refer to "Waypoints, routes, and trails" on page 34.
Menu options
You can use menu options to:
• navigate to cursor
• navigate to a waypoint
• navigate a route
While navigating, the menu expands to provide options to:
• skip waypoints when navigating a route
• restart navigating to cursor, a waypoint or a route
• cancel navigating to cursor, a waypoint or a route
Navigate to cursor position
You can start navigating to a cursor position on any chart/GPS
plotter or sonar panel.
Position the cursor at the selected destination on the panel, and
then select the Goto Cursor option in the menu.
Ú Note: The Goto Cursor menu option is not available if you are
already navigating.
Navigating | Eagle Eye Operator Manual
43
Navigate to a waypoint
You can start navigating towards a waypoint on the panel. Position
the cursor over the waypoint, select the waypoint in the menu and
then the Goto waypoint option in the menu.
Navigate a route
You can navigate a route on the image by positioning the cursor
over the route, selecting the route in the menu and then the start
route option in the menu.
When route navigation is started, select the Navigation menu
option for canceling the navigation, skipping a waypoint, and
restarting the route from current vessel position.
Navigation settings
Arrival radius
Sets an invisible circle around the destination waypoint.
The vessel is considered to have arrived at the waypoint when it is
within this radius.
XTE limit
This setting defines how far the vessel can deviate from the selected
route. If the vessel goes beyond this limit, an alarm is activated.
44
Navigating | Eagle Eye Operator Manual
XTE alarm (Cross track error)
Turns on/off the XTE alarm.
Trails
Opens the Trails dialog where trails settings can be adjusted and
trails can be converted into routes for navigation. Refer to "Trails" on
page 40.
Logging type
You can select to record trail points based on time, distance, or by
letting the unit position a point automatically when a course
change is registered.
Specify one of the following logging types in the Navigating
Settings dialog:
• Auto - the unit positions a point automatically when a course
change is registered.
• Distance - select the Distance field and enter the distance you
want to record.
• Time - select the Time field and enter the time you want to
record.
Navigating | Eagle Eye Operator Manual
45
7
Sonar
The Sonar function provides a view of the water and bottom
beneath your vessel, allowing you to detect fish and examine the
structure of the bottom.
The Sonar image
1
2
3
4
5
1
Fish arches
2
Speed over ground*
3
Depth*
4
Water Temperature*
5
Bottom
6
Range scale
* Optional Sonar data overlay that you can modify. Refer to "Data
overlay" on page 18.
Zooming the image
You can zoom the image by using the Zoom keys.
The zoom level is shown on the bottom left side of the image.
46
Sonar | Eagle Eye Operator Manual
6
When zooming with no active cursor, the sea floor is kept near the
bottom of the screen. If the cursor is active, the unit zooms where
the cursor is pointed.
You can also zoom the image as a split screen and display zoom
bars. Refer to split screen "Zoom" on page 51.
Using the cursor on the image
When you position the cursor on the image the screen pauses, the
depth at the cursor position is shown, and the information window
and the history bar are activated.
Viewing history
You can view sonar history by panning the image. To pan the
image, position the cursor on the image. This stops automatic
scrolling.
• Use the left Arrow key to move the cursor to left edge of the
image. Continue pressing the left Arrow key so the image pans to
the left and the historical image is viewed.
• Use the right Arrow key in the same manner to pan the image
back to the right and display the most current image.
• To resume normal scrolling, press the Exit key to remove the
cursor from the image.
Start recording sonar log data
You can start recording sonar log data and save the file internally in
the unit, or save it onto a card inserted into the unit’s card reader.
The Log sonar dialog is activated from the System Controls, or from
the Sonar Settings dialog.
When the data is being recorded, there is a flashing red symbol in
the top left corner and a message appears periodically at the
bottom of the screen.
Sonar | Eagle Eye Operator Manual
47
Filename
Specify the name of the recording (log).
File format
Select a file format from the drop-down, slg (Sonar only), xtf
(Structure only*), or sl2 (Sonar and Structure).
Ú Note: XTF format is for use only with select 3rd party Sonar
viewing tools.
Save to
Select whether the recording is to be saved internally or to a storage
device connected to the unit.
Time remaining
Shows the remaining allocated space available for recordings.
Stop recording sonar log data
Select Stop logging in the System Controls dialog and then Stop in
the Logging Sonar dialog to stop the recording of all sonar log data.
Viewing the recorded sounder data
Both internally and externally stored sounder records may be
reviewed when the view sonar log option is selected in the Sonar
settings dialog. Refer to "Sonar settings" on page 53.
48
Sonar | Eagle Eye Operator Manual
Customize the image settings
By default the unit is set to Auto mode, and most settings are
automated. It is recommended that only experienced sonar users
use the customize settings to further customize the image.
Select Auto in the menu and change to Custom or Ice Fishing mode
to customize image settings.
Use More options in the menu, to set access additional options for
the image. Refer to "More options" on page 51.
Custom and Ice Fishing mode options
Custom and Ice fishing modes allow access to controls for manually
tuning the sonar.
Ú Note: The options below are only visible in Custom or Ice
Fishing modes.
The range
The range setting determines the water depth that is visible on the
screen.
Sensitivity
Increasing Sensitivity shows more detail on the screen. Decreasing
Sensitivity displays less. Too much detail clutters the screen.
Conversely, desired echoes may not be displayed if Sensitivity is set
too low.
Ú Note: Auto Sensitivity is the preferred mode for most
conditions.
Auto sensitivity
Auto sensitivity automatically adjusts the sonar return to the
optimal levels. Auto sensitivity can be adjusted (+/-) to your
preference while still maintaining the auto sensitivity functionality.
Adjusting Sensitivity
1. Select the Auto sensitivity menu option to turn off the auto
setting.
2. Use the Arrow keys to highlight the scroll bar menu option.
3. Press the Enter key to activate it.
Sonar | Eagle Eye Operator Manual
49
4. Use the Arrow keys to adjust it.
5. Press the Enter key to confirm the setting.
6. Press the Exit (X) key to leave the menu.
Advanced options
Ping speed
Ping speed controls the rate the transducer transmits the signal into
the water. By default, the ping speed is set to max. It may be
necessary to adjust the ping speed to limit interference.
Scroll speed
You can select the scrolling speed of the image on the screen. A
high scroll speed updates the image fast, while a low scroll speed
presents a longer history.
Ú Note: In certain conditions it may be necessary to adjust the
scroll speed to get a more useful image. Such as adjusting the
image to a faster speed when vertically fishing without moving.
Noise rejection
Signal interference from bilge pumps, engine vibration and air
bubbles can clutter the image.
The noise rejection option filters the signal interference and reduces
the on-screen clutter.
Surface clarity
Wave action, boat wakes, and temperature inversion can cause
onscreen clutter near the surface. The surface clarity option reduces
surface clutter by decreasing the sensitivity of the receiver near the
surface.
Colorline
Allows the user to adjust the colors of the display to help
differentiate softer targets from harder ones. Adjusting the Colorline
can help separate fish and important structures on or near the
bottom from the actual bottom.
Use the up and down Arrow keys to adjust the scroll bar.
50
Sonar | Eagle Eye Operator Manual
Restore mode default
This menu option is available if you customize one or more settings.
When selected all the customized settings are changed back to the
default settings.
More options
Split screen options
Split screen options are available on the split screen sub-menu.
Zoom
1
2
1
Zoom level
2
Zoom bars
The Zoom mode presents a magnified view of the sounder image
on the left side of the panel. By default, the zoom level is set to 2x.
You can zoom up to 8x, using the Zoom keys. The range zoom bars
on the right side of the display shows the range that is magnified. If
you increase the zooming factor the range is reduced. You see this
as reduced distance between the zoom bars.
Sonar | Eagle Eye Operator Manual
51
Bottom lock
The bottom lock mode is useful when you want to view targets
close to the bottom. In this mode, the left side of the panel shows
an image where the bottom is flattened. The range scale is changed
to measure from the seabed (0) and upwards. The bottom and the
zero line are always shown on the left image, independent of the
range scale. The scaling factor for the image on the left side of the
panel is adjusted as described for the Zoom option.
Flasher
The Flasher mode shows a flasher-style sonar view in the left panel
and a normal sonar view in the right panel.
Amplitude scope
The amplitude scope is a display of an echo sounding on the panel.
The strength of the actual echoes are indicated by both width and
color intensity.
Palettes
You can select between several display palettes.
Fish ID
You can select how you want the fish targets to appear on the
screen. You can also select if you want to be notified by a beep
when a fish ID appears on the panel.
Traditional fish arches
Fish symbols
Fish symbols and depth
indication
Ú Note: Not all fish symbols are actual fish.
Fish ID beeps
When selected the system beeps when a fish is identified.
52
Sonar | Eagle Eye Operator Manual
Overlay DownScan
When a DownScan capable transducer is connected to your system,
you can overlay DownScan images on the regular Sonar image.
When overlay DownScan is activated, the Sonar panel menu
expands to include basic DownScan options.
Sonar settings
Log sonar
Select to start and stop recording of Sonar data. For more
information, refer to "Start recording sonar log data" on page 47.
View Sonar log
Used to view sonar recordings.
The log file is displayed as a paused image. You control the scrolling
and display from the Control menu option. You can use the cursor
on the replay image, and pan the image as on a normal sonar
image.
You exit the view function by pressing the Exit key.
Depth offset
All transducers measure water depth from the transducer to the
bottom. As a result, water depth readings do not account for the
distance from the transducer to the lowest point of the boat (for
example; bottom of the keel, rudder, or skeg) in the water or from
the transducer to the water surface.
Sonar | Eagle Eye Operator Manual
53
Before setting the offset, measure the distance from the transducer
to the lowest point of the boat in the water or from the transducer
to the water surface.
B
A
A
Lowest point of vessel offset: Set the distance from the
transducer to the lowest point of the boat in the water - this
should be set as a negative value. For example, - 0.3 m (-1 ft).
B
Depth below surface (waterline) offset: Set the distance from
the transducer to the surface - this should be set as a
positive value. For example, +0.5 m (+1.77 ft).
For depth below transducer, set the offset to 0.
Water temperature calibration
Temperature calibration is used to adjust the water temperature
value from the sonar transducer to match the data from another
temperature sensor. It may be required to correct for localized
influences to the measured temperature.
Calibration range: -9.9° - +9.9°. Default is 0°.
Ú Note: Water temperature calibration only appears if the
transducer is temperature capable. Check transducer type
selection if this option should be available.
54
Sonar | Eagle Eye Operator Manual
8
Live Sonar
About Live Sonar
Live Sonar is a real-time view beneath your vessel. You can examine
structures, detect fish, and watch fish react to your bait.
Live Sonar forward panel
A
B
D
C
A
Distance range scale (distance away from the transducer)
B
Underwater tree with fish swimming around it
C
Fish
D
Down range scale (distance below the transducer)
Live Sonar down panel
Live Sonar | Eagle Eye Operator Manual
55
A
E
D
C
B
A
Distance range scale (distance away from the transducer)
B
Underwater structure with schooling fish in and around it
C
School of fish
D
Single larger fish
E
Down range scale (distance below the transducer)
Zooming the image
You can zoom the image by using the display specific zoom
options.
If the cursor is active, the system zooms in where the cursor is
positioned.
Using the cursor on the panel
By default, the cursor is not shown on the image.
When you position the cursor on the panel, the image pauses and
the cursor information window is activated. The depth and range of
the cursor is shown at the cursor position.
Recording Live Sonar video
You can record Live Sonar video to a memory card.
56
Live Sonar | Eagle Eye Operator Manual
All Live Sonar recordings are done in a standard .mp4 format,
making them ideal for playback on a computer or sharing over the
internet.
Ú Note: This option is only available when a memory card is
inserted.
Stop recording video
When recording a video, the menu changes to show the stop
record option.
Modes and image settings
The unit comes with different predefined customization modes,
used to control the image settings.
Changing modes
Select the mode button and then the mode you want to use.
When the Down mode or Forward mode is selected the menu
expands with options for that mode. Both modes have More
options which provides additional image settings.
Live Sonar | Eagle Eye Operator Manual
57
Down mode menu
Forward mode menu
Auto mode
By default the unit is set to Auto mode. In this mode most settings
are automated.
Forward range
The forward range settings determine the distance that is visible on
the image.
Ú Note: This option is only available when in Forward mode.
Down range
The down range setting determines the water depth that is visible
on the image.
Noise rejection
Filters out signal interference and reduces on-screen clutter.
58
Live Sonar | Eagle Eye Operator Manual
More Options
Palettes
Use for selecting the image's color palette.
Range grid lines
The range grid can be added to the image. The grid lines are useful
for determining the distance to targets. When you select the menu
option you can choose no grid, straight line grid or arc line grid.
StableView
When selected, the transducer will offset the motion of the boat
and transducer to help provide a more stable image on the panel.
Live Sonar | Eagle Eye Operator Manual
59
9
DownScan
About DownScan
DownScan provides detailed images of structure and fish directly
below your boat. The DownScan panel is available when a
DownScan capable transducer is connected to the system.
The DownScan panel
1
2
3
4
1
Speed over ground
2
Depth
3
Temperature
4
Range scale
Zooming the DownScan image
You can zoom a DownScan image by using the Zoom keys.
Using the cursor on the DownScan panel
By default, the cursor is not shown on the DownScan image. Use
the Arrow keys to position the cursor. When you position the cursor
on a DownScan image, the screen pauses, and the cursor
information window is activated. The distance from the vessel to the
cursor is shown in the bottom row of the cursor information
window.
60
DownScan | Eagle Eye Operator Manual
The cursor depth is shown to the left of the cursor position.
To remove the cursor and the cursor elements from the panel, press
the Exit key.
GoTo cursor
You can navigate to a selected position on the image by positioning
the cursor on the panel, then using the Goto Cursor option in the
menu.
Viewing DownScan history
You can view DownScan history by panning the image. To pan the
image, press the Arrow keys to position the cursor on the image.
This stops automatic scrolling.
• Use the left Arrow key to move the cursor to left edge of the
image. Continue pressing the left Arrow key so the image pans to
the left and the historical image is viewed.
• Use the right Arrow key in the same manner to pan the image
back to the right and display the most current image.
• To resume normal scrolling, press the Exit key to remove the
cursor from the image.
Recording DownScan data
DownScan data can be recorded by selecting the correct file format
in the record dialog. Refer to "Start recording sonar data" on page 47.
Customize the image settings
By default the unit is set to Auto mode, and most settings are
automated. It is recommended that only experienced sonar users
use the customize settings to further customize the sonar image.
Select Auto in the menu and change to custom mode to customize
image settings.
Additional options are available for the Auto and Custom modes.
Refer to "More options" on page 64.
When the cursor is active, some options in the menu are replaced
with cursor mode features. Press the Eagle key to remove the cursor
from the image and cursor menu options.
DownScan | Eagle Eye Operator Manual
61
Custom mode options
When the custom mode is selected the menu expands with more
options. Use these menu options to customize the image.
Range
The range setting determines the water depth that is visible on the
image.
Auto range
By default, the range is set to Auto. With Auto, the system
automatically displays the whole range from the water surface to
the bottom.
Preset range levels
Allows for the selection of a specific depth range that is not tied to
the depth of the water.
Restore mode default
This menu option is available if you customize one or more settings.
When selected all the customized settings are changed back to the
default settings.
Contrast
Determines the brightness ratio between light and dark areas of the
screen.
Ú Note: We recommend you use Auto contrast.
To adjust the contrast setting:
1. Select the contrast option in the menu.
2. Select Auto contrast and press the Enter key to turn off autocontrast.
3. Use the Arrow keys to highlight the adjustment bar and press
the Enter key to activate it.
4. Use the Arrow keys to adjust the setting.
5. Press the Enter key to save your settings.
FishReveal
Select FishReveal to display fish arches in the image.
62
DownScan | Eagle Eye Operator Manual
When FishReveal is enabled, the menu expands to include
FishReveal options.
Sensitivity
Controls the sensitivity of the FishReveal data. Increasing sensitivity
shows more detail on the screen. Decreasing sensitivity displays less.
Too much detail clutters the screen. If the sensitivity is set too low,
weak fish arch data might not be displayed.
Colorline
Adjusts the colors of the fish arch data to help differentiate them
from other targets. Adjusting the colorline can help separate fish
and important structures on or near the bottom from the actual
bottom.
Surface clarity
Wave action, boat wakes and temperature inversions can cause
onscreen clutter near the surface. This option reduces surface clutter
of FishReveal data by decreasing the sensitivity of the receiver near
the surface.
Palette
Select between several display palettes optimized for a variety of
fishing conditions.
Ú Note: Palette choice is often a user preference, and may vary
depending on the fishing conditions. It is best to select a
palette that provides good contrast between the image details
and FishReveal arches.
DownScan | Eagle Eye Operator Manual
63
Advanced options
Surface clarity
Wave action, boat wakes and temperature inversions can cause onscreen clutter near the surface.
The surface clarity option reduces surface clutter by decreasing the
sensitivity of the receiver near the surface.
Ú Note: By default, surface clarity is set to Low, for optimal image
return and clarity.
More options
Range Lines
Range lines can be added to the image to make it easier to estimate
depth.
Palettes
You can select between several display palettes.
64
DownScan | Eagle Eye Operator Manual
10
Alarms
Alarm system
The system continuously checks for dangerous situations and
system faults while the system is running. When an alarm situation
occurs, an alarm message pops up on the screen.
If you have enabled the siren, the alarm message is followed by an
audible alarm.
The alarm is recorded in the alarm listing so that you can see the
details and take the appropriate corrective action.
Type of messages
The messages are classified according to how the reported situation
affects your vessel. The following color codes are used:
Color
Importance
Red
Critical alarm
Orange
Important alarm
Yellow
Standard alarm
Blue
Warning
Green
Lite warning
Alarm messages
An alarm message is displayed with the name of the alarm as the
title, and with details for the alarm.
Acknowledging a message
The alarm dialog options for acknowledging a message vary
depending on the alarm:
• Close. Sets the alarm state to acknowledged. The siren/buzzer
stops and the alarm dialog is removed. However, the alarm
remains active in the alarm listing until the reason for the alarm
has been removed.
Alarms | Eagle Eye Operator Manual
65
• Disable. Disables the current alarm setting. The alarm does not
show again unless you turn it back on in the alarm settings
dialog.
There is no time-out on a message or the siren. They remain active
until they are acknowledged or until the reason for the message is
rectified.
Alarms dialog
Enable the alarm siren from the Alarms dialog.
Select the settings option to open the Alarms Settings dialog. All
alarms are setup in the Alarms Settings dialog.
66
Alarms | Eagle Eye Operator Manual
11
Tools
The Tools panel includes icons used for accessing options and tools
that are not specific to any panel.
The Tools panel is located on the Home page.
Settings
Provides access to application and system settings.
System settings
The system settings provides access to the following options.
Language
Controls the language used on this unit for panels, menus, and
dialogs. Changing the language causes the unit to restart.
Boat settings
Used to specify the physical attributes of the boat.
Text size
Used for setting the text size in menus and dialogs.
Tools | Eagle Eye Operator Manual
67
Key beeps
Controls the loudness of the beep sound when a key is pressed.
Time
Controls the local time zone offset, and the format of the time and
date.
Datum
Most paper charts are made in the WGS84 format, which also is
used by the Eagle Eye.
If your paper charts are in a different format, you can change the
datum settings accordingly to match your paper charts.
Coordinate system
Several coordinate systems can be used to control the format for
latitude and longitude coordinates displayed on the panel.
Magnetic variation
Magnetic variation is the difference between true bearings and
magnetic bearings, caused by different locations of the Geographic
and the Magnetic north poles. Any local anomalies such as iron
deposits might also affect the magnetic bearings.
When set to Auto, the system automatically converts magnetic
north to true north. Select manual mode if you need to enter your
own local magnetic variation.
Satellites
Status page for active satellites.
Restore defaults
Allows you to select which settings are to be restored to their
original factory settings.
Warning: If waypoints, routes, and trails are selected,
they are permanently deleted.
68
Tools | Eagle Eye Operator Manual
Advanced
Shows a panel with more advanced settings. Used for setting how
your system displays various user interface information. In addition,
controls which features are shown in the interface.
Registration
Prompts you to register your device. Registration can be done:
• From a smart device with internet access
• By calling
About
Displays copyright information, software version, and technical
information for this unit.
The Support option accesses the service assistant, refer to "Service
assistant" on page 72.
Navigation
Provides options and dialogs where you specify settings for your
navigation, such as arrival radius, XTE limit, XTE Alarm, Trails, and
Logging Type. Refer to "Navigation settings" on page 44.
Chart
Provides options and dialogs where you specify settings for your
charts. Settings and display options made in the Chart settings page
are common for all chart panels. Refer to "Chart settings" on page 32.
Sonar
Provides options and dialogs where you specify settings for your
sonar. Refer to "Sonar settings" on page 53.
Alarms
Provides the option to enable the siren. It also provides a dialog
where you specify turning on alarms for items, and includes active
alarm information and alarm history. Refer to "Alarms dialog" on page
66.
Units
Allows you to set up the units of measure for various data types.
Tools | Eagle Eye Operator Manual
69
Network
Provides information and options about the network data between
your display and your transducer.
Simulator
Provides for manually controlling the simulator. For more
information, refer to "Simulator" on page 77.
Waypoints/routes/trails
List of waypoints, routes, and trails with details. For more
information, refer to "Waypoints, routes, and trails" on page 34.
Info
Access to Sun/moon, Tides and Trip information.
Sun, Moon
Displays sunrise, sunset, moonrise and moonset for a position based
on entered date and the position’s latitude/longitude.
Tides
Displays tide information for the tide station nearest to your vessel.
Available tide stations can be selected from the Tide station field.
To change the date, use the Arrow keys to access the date field and
press the Menu/Enter key to access the calendar function.
Trip
Provides trip information. Use to reset trip information.
Storage
Access to the file management system. Use to browse and manage
the contents of the unit's internal memory and storage devices
connected to the unit.
Copying files to a storage device
You can copy user data such as screen captures, logs, etc. to a
storage device connected to the unit. You can also export user data
such as System Settings, Waypoints, Routes, and Trails to the storage
70
Tools | Eagle Eye Operator Manual
device. Exporting files is covered in the section "Maintenance" on page
72.
Tools | Eagle Eye Operator Manual
71
12
Maintenance
Preventive maintenance
The unit does not contain any field serviceable components.
Therefore, the operator is required to perform only a very limited
amount of preventative maintenance.
It is recommended that you always fit the protective sun cover
when the unit is not in use.
Cleaning the display unit
To clean the screen:
• A micro-fiber or a soft cotton cloth should be used to clean the
screen. Use plenty of water to dissolve and take away salt
remains. Crystallized salt, sand, dirt, etc. can scratch the protective
coating if using a damp cloth. Use a light fresh water spray then
wipe the unit dry with a micro-fiber or a soft cotton cloth. Do not
apply pressure with the cloth.
To clean the housing:
• Use warm water with a dash of liquid dish soap or detergent.
Avoid using abrasive cleaning products or products containing
solvents (acetone, mineral turpentine, etc.), acid, ammonia, or
alcohol as they can damage the display and plastic housing.
Do not:
• use a jet or high pressure wash
Checking the connectors
Push the connector plugs into the connector. If the connector plugs
are equipped with a lock or a position key, ensure that it is in the
correct position.
Service assistant
The system has a built-in service assistant that creates a report of
the unit which includes the software version, serial number, and
information from the settings file to assist in technical support
enquiries.
1. Insert an empty memory card in the unit.
72
Maintenance | Eagle Eye Operator Manual
2. Open the About page of the System settings dialog.
3. Select Support and then Create report.
4. Follow the instructions.
5. Save the report to the memory card.
You can add screenshots and log files that will be attached to the
report. There is a 20MB limit for the report attachments. If you call
technical support first, you can enter an incident number to assist
with tracking.
Email the report from the memory card to support using a smart
device or PC connected to the internet.
Software updates
Before initiating an update to the unit, be sure to back up any
potentially valuable user data.
Update software
Ú Note: Do not download software updates to mapping cards.
Use a non-mapping memory card with sufficient storage for
software updates, or saving reports or files to it.
Ú Note: Do not turn off the unit until the update is completed.
1. Download the software update from www.lowrance.com to a
memory card inserted in a smart device or PC connected to the
internet.
2. Power off your unit and then insert the card containing the
software updates in your unit.
3. Power on your unit. A progress bar appears showing the
software is being updated. Let the update complete, do not
power off the unit. Do not remove the card until after the unit
has restarted.
Maintenance | Eagle Eye Operator Manual
73
Backing up your system data
It is recommended to regularly copy user data and your system
settings database as part of your back-up routine.
Export all Waypoints, Routes and Trails
Use the export option if you want to backup all Waypoints, Routes,
and Trails on your system.
Export region
The export region option allows you to select the area from where
you want to export data.
1. Select export region.
2. Place the cursor over one of the boundary box corners and
press the Menu/Entry key to select it.
3. Use the Arrow keys to move the selected boundary box corner
to expand the box.
4. Press the Menu/Entry key to place the corner.
5. If needed, repeat steps 2-4 to the other boundary box corner.
6. Press the Exit (X) key to indicate that the box covers the region
you want to export. The Export Region dialog opens.
7. Select the export option.
8. Select the appropriate file format.
9. Select Export and follow the prompts for specifying the
destination folder and a file name.
74
Maintenance | Eagle Eye Operator Manual
Export format
The following formats are available for export:
• User Data File version 6
Used to export waypoints, routes and colored tracks/trails.
• User Data File version 5
Used to export waypoints and routes with a standardized
universally unique identifier (UUID), which is very reliable and
easy to use. The data includes such information as the time and
date when a route was created.
• User Data File version 4
Best used when transferring data from one system to another,
since it contains all the extra bits of information these systems
store about items.
• User Data file version 3 (with depth)
Should be used when transferring user data from one system to a
legacy product.
• User Data file version 2 (no depth)
Can be used when transferring user data from one system to a
legacy product.
• GPX (GPS Exchange, no depth)
This is the format most used on the web that shares among most
GPS systems. Use this format if you are taking data to a
competitor's unit.
Purging user data
Deleted user data are stored in the unit's memory until the data is
purged. If you have numerous deleted, unpurged user data, purging
may improve the performance of your system.
Ú Note: When user data is deleted and/or purged from the
memory, it cannot be recovered.
Maintenance | Eagle Eye Operator Manual
75
Exporting the settings database
Use the settings database option in the storage dialog to export
your user settings.
Importing backed up files
1. Insert the memory card containing the backed up files in the
unit's card reader.
2. Open the Storage dialog from the tool panel and select the
memory card.
3. Browse to the file you want to import and select it. This opens
the details dialog.
4. Select the import option and follow the prompts.
A message advises when the import is completed.
76
Maintenance | Eagle Eye Operator Manual
13
Simulator
The simulation feature lets you see how the unit works in a
stationary position and without being connected to other devices.
You access the simulator from Settings tool.
Retail mode
In this mode, a retail demonstration for the selected region is
shown.
If you operate the unit when retail mode is running, the
demonstration pauses.
After a time-out period, retail mode resumes.
Ú Note: Retail mode is designed for retail/showroom
demonstrations.
Simulator source files
You can select which sonar data files are used by the simulator. A
set of source files is included in your system, and you can import
files by using a card inserted into the card reader. You can also use
your own recorded sonar log data files in the simulator.
Simulator | Eagle Eye Operator Manual
77
Advanced simulator settings
The Advanced simulator settings allows for manually controlling the
simulator.
GPS source
Selects the file for the simulated GPS data.
Speed and Course
Used for manually entering values when GPS source is set to
Simulated course. Otherwise, GPS data including speed and course
come from the selected source file.
Set start position
Sets your simulated vessel position to the current cursor position.
Ú Note: This option is only available when the GPS source is set to
simulated course.
78
Simulator | Eagle Eye Operator Manual
Document version: 002
© 2026 Navico Group. All Rights Reserved.
Navico Group is a division of Brunswick Corporation.
Reg. U.S. Pat. & Tm. Off, and ™ common law marks.
Visit www.navico.com/intellectual-property to review
the global trademark rights and accreditations for
Navico Group and other entities.
®
www.lowrance.com
">