WARNING - EXPLOSION HAZARD -
SUBSTITUTION OF COMPONENTS
MAY IMPAIR SUITABILITY FOR
CLASS | DIVISION 2
WARNING - EXPLOSION HAZARD -
DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED
OFF OR THE AREA 18 KNOWN TO BE
pa pu ©
B
3
|
Ё
OR MODEM
\М I
1/0 EXPANSION
C267, C277, C287
MCCA72 PART # 50-05-0782
MILLENNIUM HEAD MODEL NUMBERS
REF. DWG 50-00-0385
THIS EQUIPMENT IS SUITABLE FOR USE IN CLI, DIV2 GRPS. C,D
(T3) HAZARDOUS LOCATIONS.
SEE NOTE®
TS
SENSOR INPUT CONFIGURED FOR
SENSOR WITH SINGLE WIRE TO
GROUND. nos DL
SENSOR INPUT CONFIGURED FOR
SENSOR WITH SINGLE WIRE TO
POWER SUPPLY POSITIVE. db TS
ss —o fo ———-
=O
SENSOR INPUT CONFIGURED FOR
TWO WIRE INPUT.
dL TS
ss —o fo ———-
SENSOR INPUT CONFIGURED FOR
TWO WIRE INPUT.
JSI
5 5 +\6
SHUNT INSTALLED IN JSI
ONLY
+
se 1
JSI
o +VS SHUNT INSTALLED IN
JS2 ONLY
, FR
Js2 |
JSI
o +Vs
SHUNT NOT REQUIRED
3
us? L
JSI
o— +Vs
SHUNT NOT REQUIRED
us
ye L
1/P
МР
RS&85 SERIAL 1/0
COMA
I0A, 125VAC, SA,
30VDC TYPICAL FOR
ALL FOUR
MAXIMUM
LOAD 3A
RELAY
OUTPUTS MD
POWER INPUT |
LOAD
MAXIMUM INES
LOAD 3A pos 000
MAXIMUM — — — — —
LOAD 3A - — — —
— NEG _ _— — — —
“400
_
MAXIMUM POS
LOAD 3A
HH
MILLENNIUM POWER SUPPLY MODEL NUMBERS
MCPS-NA PART # 50-70-0508
MCPS-Al PART 4 50-70-0306
MCPS-A2 PART # 50-70-0307
REF. DWG 50-00-0357
ICDB CONNECTOR
7
JR-I
— rh CHGND
—
+
<Q
©
TSS
J!
||
b
+
sel O | n-2omA ®
420 (O | CURRENT SOURCE H
SHG 3 L-20MA + MAGNETIC PICKUP
+20 (©) | CURRENT SOURCE wh
1 20 (©) +
0
oN
SHG 3 ®
=
alo ;
5 :
©
=
TS3
OOOOOOOO OOOOOOO0O
|0000000000000000|0000000000000000| up
NON-INCENDIVE FIELD
WIRING CONNECTIONS TO
NOTES:
(D) FIELD WIRING CONNECTIONS TO BE
INSTALLED IN ACCORDANCE WITH THE
NEC FOR CLASS |, DIV 2, GRPS C AND D
HAZARDOUS LOCATIONS.
(2) INSTALL SEPARATE CONDUCTORS FOR
SSR AND CONTROLLER POWER INPUT.
ALLOW FOR CONDUCTOR VOLTAGE DROP
WHEN DETERMINING CONDUCTOR SIZE.
ALL POWER SUPPLIES MUST HAVE
COMMON GROUND.
(3) FOR AN INDUCTIVE LOAD, INSTALL A
DIODE IN PARALLEL WITH THE LOAD.
USE A FAST RECOVERY 3A, S0PIV
DIODE. MOUNT DIODE AS CLOSE AS
POSSIBLE TO THE LOAD DEVICE.
MAXIMUM LOAD INDUCTANCE: IH @
0.25A, SMH @ SA.
(4) RL = (Ves - 3.15)/0.20
RL = LOOP RESISTANCE
VPS = POWER SUPPLY VOLTS
(5) SENSOR SWITCH INPUT CURRENT:
2.5MA MAX @ IOVDC, 9.2MA @ 52VDC
© MINIMUM CHARGE/DISCHARGE CYCLE
TIME 9 MIN.
b
+
0
я * | PASSIVE SWITCHES FOR
E 4 || USE IN CLI, DIV2, GRPS C TYPICAL NORMALLY
| $ AND D HAZARDOUS CLOSED SENSOR FOR
A * | LOCATIONS. ROUTE USE IN CLI, DIVZ,
К 4 || SWITCH LEADS SEPERATE GRPS, C AND D
| ı | FROM ALL OTHER WIRING. HAZARDOUS
E 2 LOCATIONS.
0
O 2 s+ 020 10 Ne +) _
| SG Lt | A TYPICAL NORMALLY |
00 2 FT) __NO ST com OPEN SENSOR FOR |
e о Л USE IN CLI, DIV2, |
$ | GRPS, C AND D
38390 © E HAZARDOUS |
ER _ | SSR POWER SUPPLY — LOCATIONS. |
oO = Flea] LEADS | —_— |
ME © Е L Г 0
15 ELE A ami. | A
— © в ия E | EN EE O aa NEG
23 AL e JA Es" o
— + O NM В O POSmm mmm Do =
15 О Eo] E O Nec == = | | POWER SUPPLY | |
Hee O pose — =) == == —= = || 10-32VDC |
——— O сы : С) |МЕСищнни | | |
49 BO} ea gy бе
8 O a - O = пн — пин = O 68 1 — Bp ros | |
og gol | 50 || ql |_ 7 |
| VE © =~ | | \ -— 7 | |
| o 4-0
WARNING - EXPLOSION HAZARD - DO NOT | L mes) NEG
DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN | USER SUPPLIED |
SWITCHED OFF OR THE AREA IS KNOWN TO BE
NON HAZARDOUS | ©| © — POWERSUPPLY |
== mm) POS
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT
DE DECONNECTER
MCCP PART # 50-70-0326
L' EQUIPEMENT, COUPER LE COURANT OU
S'ASSURER QUE L'EMPLACEMENT EST DESIGNE REF DWG 50-00-0395
NON DANGEREUX.
С
REMOVED MILLENNIUM HEAD MODEL NUMBERS:
50700302, 50700303, 50700304 8 50700305 02-26-02 02-0155 | DPMc | DMc
UNLESS NOTED OTHERWISE
NTS
x) murph
WRB RH ®
INSTALLATION DIAGRAM
MILLENNIUM CONTROLLER
90-08-0040 | C
">
