Craftsman 486.24218 Owner`s manual
Add to my manuals
12 Pages
Craftsman 486.24218 Dethatcher is here to restore your lawn to its natural beauty by removing thatch buildup from your grass. This dethatcher features a 20-inch working width, allowing you to cover a lot of ground quickly. The depth of the tines can be adjusted to suit your needs, and the dethatcher is easy to maneuver, thanks to its lightweight design and large wheels. It also has multiple transport hook positions and can be connected to sweepers with single and double hitch tubes.
advertisement
Owner's Manual
®
STOP
DETHATCHER FOR SWEEPERS
Model No. 486.24218
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
CAUTION:
Before using this product, read this manual and follow all Safety
Rules and
Operating Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
PRINTED IN U.S.A.
• Safety
• Assembly
• Operation
• Maintenance
• Parts
FORM NO. 41268 (7-21-09)
TABLE OF CONTENTS
SAFETY RULES ..........................................................2
FULL SIZE HARDWARE CHART ................................3
CARTON CONTENTS .................................................4
ASSEMBLY ..................................................................4
OPERATION ................................................................7
MAINTENANCE/STORAGE ........................................7
REPAIR PARTS .........................................................9
PARTS ORDERING/SERVICE .....................Back Page
WARRANTY
CRAFTSMAN FULL WARRANTY
When operated and maintained according to all supplied instructions, if this Craftsman product fails due to a defect in material or workmanship within one year from the date or purchase, return it to any Sears store or other Craftsman outlet in the United States for free replacement.
This warranty applies for only 90 days from the date of purchase if this product is ever used for commercial or rental purposes.
This warranty does not include items considered to expendable parts that can wear out from normal use within the warranty period.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179
DO NOT RETURN TO STORE for Missing Parts or Assembly Questions
Call 1-866-576-8388 Attachment Hotline
The model number and serial numbers will be found on a decal attached to the dethacther.
You should record both the serial number and the date of purchase and keep in a safe place for future reference.
MODEL NUMBER: 486.24218
SERIAL NUMBER: __________________
DATE OF PURCHASE:__________________
SAFETY
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.
Exercise caution at all times, when using power equipment.
• Read this owners manual carefully for operating and service instructions before attempting to assemble or operate the dethatcher. Be thoroughly familiar with the proper use of the dethatcher.
• Read the vehicle owners manual and vehicle safety rules, and know how to operate the vehicle before using the dethatcher.
• Read the lawnsweeper owners manual and safety rules, and know how to operate the lawnsweeper before using the dethatcher.
• Never allow children to operate the tractor or dethatcher attachment, and do not allow adults to operate without proper instructions.
• This dethatcher attachment has sharp tine points.
Always handle with care and wear substantial foot wear when operating this dethatcher.
• Do not allow anyone to ride or sit on the dethatcher, lawnsweeper or towing vehicle.
• Keep the area of operation clear of all persons, particularly small children, and also pets.
2
• Always begin with the transmission in first (low) gear and engine at low speed, and gradually increase speed as conditions permit.
• Vehicle braking and stability may be affected with the attachment of this equipment. Be aware of changing conditions on slopes. Refer to safety rules in the vehicle owner's manual concerning safe operation on slopes. STAY OFF OF STEEP SLOPES.
• Always operate up and down a slope, never across the face of a slope
• This equipment should be operated at reduced speed on rough terrain, along creeks and ditches and on hillsides, to prevent tipping and loss of control.
Do not drive too close to a creek or a ditch.
• Follow the maintenance instructions as outlined in this owners manual.
Look for this symbol to point out important safety precautions. It means — Attention!!
Become alert!! Your safety is involved.
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
5
HARDWARE PACKAGE CONTENTS
6 7
8
9
19
10
11
12
13
18
14
15
16
17
20
NOT SHOWN FULL SIZE
22
21 23
24
REF.
pART No. qTY.
5
6
7
8
9
46526
44292
43085
48813
48811
3
2
7
2
1
DESCRIpTIoN
Hex Bolt, 1/2-13 x 3-1/2"
Hex Bolt, 5/16-18 x 2-1/2"
Hex Bolt, 5/16-18 x 1-1/2"
U-Bolt, 1/4-20
Transport Hook
10 43081 2 Washer, 5/16"
11 R19171616 2 Washer, 1/2"
12 43070 14 Washer, 3/8"
13
14
43055
47189
2 Hair Cotter Pin, 3/32"
4 Nylock Nut, 1/4-20
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
REF.
pART No. qTY.
15 47810 9
DESCRIpTIoN
Nylock Nut, 5/16-18
16 43019 1 Jam Nut, Plain 1/2-13
17
18
19
20
21
48115
48812
44481
48917
25054
3
2
2
2
2
Jam Nut, Nylock 1/2-13
Clevis Pin, 5/16" x 1-3/8"
Vinyl Cap
Clamp
Bracket, U-Bolt Clamp
22 46499
23 741-0248
24 42212
2 Spacer
4 Flange Bearing
1 Double Transport Hook
3
CARTON CONTENTS
1. Spring Tines (7)
2. Frame Assembly
3. Gauge Wheel
4. Mount Brackets (2)
1
ASSEMBLY
NOTE: On sweepers smaller than 42", use only five spring tines.
• Assemble a vinyl cap onto each end of the frame tube.
See figure 1.
5/16" x 1-1/2"
HEX BOLT
VINYL CAP
3/8" WASHER
3
2
4
TOOLS REQUIRED FOR ASSEMBLY
(1) 7/16" Wrench
(2) 1/2" Wrenches
(2) 3/4" or Adjustable Wrenches
(1) Knife
REMOVAL OF PARTS FROM CARTON
• Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 3 and 4.
• Turn the frame assembly as shown in figure 1.
• Assemble seven spring tines to the top of the frame tube. Use a 5/16" x 1-1/2" hex bolt, two 3/8" flat washers and a 5/16" nylock nut for each spring tine.
Place one 3/8" flat washer on top of the frame tube and the second 3/8" flat washer on top of the spring tine. See figure 1.
4
FIGURE 1
5/16" NYLOCK NUT
VINYL CAP
• Assemble a 1/2" washer, the wheel, another 1/2" washer and the 1/2" plain jam nut onto the
1/2" x 3-1/2" hex bolt. See figure 2.
• Insert the bolt through the welded bracket and assemble the 1/2" nylock jam nut onto the bolt. Adjust the nuts so that there is no end play in the wheel and then tighten the nuts securely against the welded bracket. Make sure the wheel still turns freely. See figure 2.
Use this hole for
42" & 46" sweepers
Use this hole for smaller sweepers
1/2" NYLOCK
JAM NUT
1/2" JAM NUT
1/2" WASHER
1/2" WASHER
1/2" x 3-1/2"
HEX BOLT
FIGURE 2
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
SWEEpERS WITH TWo HITCH TUBES
Skip to page 6 for sweepers with single hitch tubes.
• Assemble a conduit clamp onto each end of the sweeper height adjustment tube so that the straight part of the clamp is on top of the tube.
• Remove the hitch brackets from the sweeper's hitch tubes. Slide the transport hook onto the L.H. hitch tube as shown in figure 3.
• Reassemble the hitch brackets and bolts to the hitch tubes. Refer to your sweeper owner's manual.
If you have a 30" sweeper, skip to figure 6.
• Make sure the sweeper height adjustment handle is still set to about the middle of it's adjustment range.
• Center the dethatcher with the sweeper.
• Assemble the keeper brackets (bend to the inside) to the sweeper's hitch tube, outside of the conduit clamps. Use a u-bolt and two 1/4" nylock nuts per bracket. Position the keeper brackets against the sides of the conduit clamps, approximately perpendicular to the ground. Tighten the nuts without bending the keeper brackets. See figure 5.
KEEPER BRACKET
U-BOLT
HEIGHT ADJ.
TUBE
FIGURE 3
CONDUIT
CLAMP
TRANSPORT
HOOK
• Connect the sweeper to the tractor. Set the sweeper height adjustment handle to about the middle of it's adjustment range.
• Place the dethatcher in front of the sweeper housing, underneath the hitch tubes.
• Connect the dethatcher to the conduit clamps using two 5/16" x 1-3/8" clevis pins, 5/16" washers and
3/32" hair cotter pins. See figure 4.
HEIGHT ADJUSTMENT
MIDDLE SETTING
5/16" x 1-3/8"
CLEVIS PIN
5/16" WASHER
1/4" NYLOCK NUT
FIGURE 5
• Lift the front of the dethatcher and secure it in transport position using the transport hook. See figure 6.
• To keep the transport hook from sliding back along the hitch tube, you can fasten the supplied nylon tie around the hitch tube behind the transport hook. See figure 6.
NYLON TIE
TRANSPORT HOOK
3/32" HAIR
COTTER PIN
FIGURE 4
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
FIGURE 6
5
SWEEpERS WITH A SINGLE HITCH TUBE
NoTE: The dethatcher attaches to the sweeper's offset tube. This prevents you from offsetting the sweeper.
• Assemble the four bearings to the two spacers and then slide each through a clamp.
CLAMP
BEARING BEARING
FIGURE 7
SPACER
• Fasten each clamp to the spring mount frame assembly using one 5/16 x 1-3/8" clevis pin, 5/16" washer, and 3/32" hair cotter pin.
5/16 x 1-3/8"
CLEVIS PIN
5/16" WASHER
3/32" HAIR
COTTER PIN
FIGURE 9
• Secure the two mount brackets to the inner holes of the drawbar offset tube of the sweeper using two 5/16 x
2-1/2" hex bolts and 5/16" nylock nuts.
5/16" x 2-1/2"
HEX BOLT
• Attach each of the bearing, spacer, and clamp assemblies to a mount bracket using a 1/2 x 3-1/2" hex bolt and 1/2" nylock jam nut.
1/2 x 3-1/2" HEX BOLT
1/2" NYLOCK
JAM NUT
5/16" NYLOCK NUT
FIGURE 10
• Place the double transport hook onto the sweeper hitch tube. Lift up the front of the dethatcher and slide it into the double hooks to secure it in the transport position.
DOUBLE TRANSPORT HOOK
FIGURE 8
6
FIGURE 11
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
OPERATION
HOW TO USE YOUR DETHATCHER
RAISING/LOWERING THE DETHATCHER
• To raise the dethatcher for transport, lift up on the front of the dethatcher and secure it with the transport hook. Lower the dethatcher by releasing the transport hook.
SETTING THE OPERATING POSITION
• The operating height of the dethatcher is controlled by the gauge wheel at the front of the dethatcher and is not adjustable. The correct wheel position was determined in figure 2 when you assembled the wheel.
• Set the sweeper to the desired operating height. (The best height is usually with the brushes set about 1/2" down into the grass.) Refer to your sweeper owner's manual.
USING THE DETHATCHER
Regular removal of thatch is critical to the maintenance of a healthy lawn. Thatch is layer of stems, clippings, runners, roots and leaves that have not decayed.
Excessive thatch prevents air, water and fertilizer from reaching the roots. The dethatcher will effectively dislodge excessive thatch from your lawn.
• Start with the tractor in low gear. Vary the forward speed to determine the best speed for maximum dethatcher performance.
• Use a crisscross pattern to achieve the most even removal of thatch.
• On slopes, always operate in an up and down direction only.
• Avoid extremely sharp turns.
• Avoid towing the dethatcher across sudden steep dips in the ground while dethatching. Loss of ground contact with the gauge wheel could cause the dethatcher to be pulled back underneath the sweeper.
MAINTENANCE / STORAGE
CUSTOMER RESPONSIBILITIES
• Read and follow the maintenance schedule and the maintenance procedures listed in this section.
MAINTENANCE SCHEDULE
Fill in dates as you
complete regular service.
Bef ore each use
After
each
Ev
use ery
season
Bef ore stor age
Check for loose fasteners X
Check for worn or damaged parts X X
Cleaning X X
Service Dates
• Before each use, check all nuts and bolts for tightness.
• Clean after each use to help prevent rust.
• If rust appears on the spring tines, sand lightly and coat with enamel paint.
• Always store in a dry area, and coat exposed metal with light oil when not in use.
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
7
NOTES
8 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
PARTS
REPAIR PARTS FOR MODEL 486.24218 DETHATCHER
4
6
5
17
15
12
7
18
10
23 20
22
23
2
13
12
24
19
18
10
20
1
15
8
17
21
14
11
16
13
19
5
REF.
pART No. qTY.
1 64650 1
DESCRIpTIoN
Spring Mount Frame Assem.
2 46761 7 Spring Tine
3
4
5
6
7
48098
26624
46526
44292
43085
1
2
3
2
7
Gauge Wheel
Mount Bracket
Hex Bolt, 1/2-13 x 3-1/2"
Hex Bolt, 5/16-18 x 2-1/2"
Hex Bolt, 5/16-18 x 1-1/2"
8
9
10
48813
48811
43081
2 U-Bolt, 1/4-20
1 Hook, Transport
2 Washer, 5/16"
11 R19171616 2 Washer, 1/2"
12 43070 14 Washer, 3/8"
13 43055 2 Hair Cotter Pin, 3/32"
11 3
9
REF.
pART No. qTY.
14 47189 4
DESCRIpTIoN
Nylock Nut, 1/4-20
15 47810 9 Nylock Nut, 5/16-18
16
17
18
19
20
43019
48115
48812
44481
48917
1
3
2
2
2
Jam Nut, Plain 1/2-13
Jam Nut, Nylock 1/2-13
Clevis Pin, 5/16" x 1-3/8"
Vinyl Cap
Clamp
21
22
23
24
25054
46499
741-0248
42212
41268
2
2
4
1
1
Bracket, U-Bolt Clamp
Spacer
Flange Bearing
Hook (Double Transport)
Owner's Manual
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
9
10 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
11
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances and items like garage door openers and water heaters.
1-800-4-MY-HOME ®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada) www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222
(U.S.A.)
1-800-469-4663
(Canada) www.sears.com www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
1-800-361-6665
(Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
®
(1-888-784-6427)
Au Canada pour service en français:
1-800-LE-FOYER
(1-800-533-6937) www.sears.ca
MC
® Registered Trademark /
® Marca Registrada / TM
TM Trademark / SM
Marca de Fábrica /
Service Mark of Sears Brands, LLC
SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement