- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Uninterruptible power supplies (UPSs)
- Voltronic Power
- Nano 400
- Quick guide
Voltronic Power Nano 400 Quick Manual
Add to My manuals2 Pages
Voltronic Power Nano 400 is a small and compact UPS that offers comprehensive power protection for home or small office applications. With its 400 VA / 240 W capacity, it can provide stable power to connected equipment during power failures, allowing you to safely shut down your PC and other devices. The Nano 400 features a simulated sine wave output and provides full protection against overcharge, discharge, short circuit, and thermal issues. Its embedded microprocessor controller ensures high reliability, and its compact size makes it easy to place anywhere in your workspace.
advertisement
Nano UPS Quick Guide
V.1.0
1
Package Contents
You should have received the following items inside of package:
UPS Unit
Quick Guide
-Power cable (only for the IEC-type model)
Product Introduction
2
The Nano UPS provides comprehensive protection in a small and economic package.
The UPS is more compact and offers greater comprehensive power protection against surges and spikes. This UPS will continue providing stable power to connected equipment and enable to shutdown PC safely during power failure. Its embedded microprocessor controller guarantees high reliability and it’s perfect for any home or small office application.
Product Overview
3
Front View:
1
2
3
1
2
3
Power switch
UPS status indicator
Fault/Battery status indicator
(Check the Indicator & Alarm Table for the details)
Installation & Initial Startup
4
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.
Placement & Storage Conditions
Install the UPS in a protected area that is free of excessive dust and has adequate air flow. Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT operate the UPS where the temperature and humidity is outside the specific limits. (Please check the specs for the limitations.)
20cm 20cm
Connect to Utility and Charging
Before initial use, please p lug in the AC input cord to the wall outlet and turn on the UPS for charging. For the best results, suggest to charge the battery at least 8 hours before initial use. The UPS charges its battery while connecting to the utility with power on.
8 hours
Connect the Loads
Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS unit, then devices connected to the UPS will be protected by UPS unit.
CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may cause the damage of the unit.
Back View:
1
2
3
1
2
IEC Type NEMA Type Universal Type Schuko Type
3
1 AC input
2
3
Output receptacles
Circuit breaker
Turn On/Off the Unit
Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again the power switch.
Indicators & Alarm Table for Operation
Conditions Visual Indications Alarm
AC mode
Battery mode
Low battery at battery mode
Green LED lighting
Green LED flashing every 10 seconds
Green LED flashing every second & Red LED lighting
Off
Sounding every 10 seconds
Sounding every second
Fault Red LED lighting Continuously sounding
Alarm for overtemperature protection
Red LED flashing every 0.5
seconds
Off
5
Important Safety Warning
(
SAVE THESE INSTRUCTIONS)
CAUTION!
To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the specifications for the acceptable temperature and humidity range.)
CAUTION!
To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.
CAUTION!
Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.
CAUTION!
In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.
CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during UPS installation in order to reduce leakage current below 3.5mA.
Attention hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary.
CAUTION!
Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries.
CAUTION! When replacing the batteries, use the same number and type of batteries.
CAUTION!
Internal battery voltage is 12Vdc. Sealed, lead-acid, 6-cell battery.
CAUTION!
Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION!
A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed before replacing batteries:
1) Remove watches, rings, or other metal objects.
2) Use tools with insulated handles.
3) Wear rubber gloves and boots.
4) Do not lay tools or metal parts on top of batteries.
5) Disconnect charging source prior to connecting or disconnecting batteries terminal.
6
Trouble Shooting
Use the table below to solve minor problems. panel.
Problem Probable Cause Solution
No LED display on the front
Alarm continuously sounds when the mains is normal.
Alarm sounds every
2 seconds when the mains is normal.
When power fails, backup time is shorten.
The mains is normal but green LED is flashing.
Low battery.
Battery fault.
The UPS is not turned on.
The UPS is overload.
UPS fault
Battery defect
Charging circuit is damaged.
The UPS is overload.
Battery voltage is too low.
Battery defect.
Power cord is loose.
Charge the UPS at least 8 hours.
Replace the battery with the same type of battery.
Press the power switch again to turn on the UPS.
Remove some loads first.
Before reconnecting equipment, please verify that the load matches the UPS capability specified in the specs.
Return the unit to service center.
Replace the battery with the same type of battery.
Return the unit to service center.
Remove some critical load.
Charge the UPS at least 8 hours.
Replace the battery with the same type of battery.
Reconnect the power cord properly.
7
Specifications
Model Nano 400 Nano 600 Nano 800
INPUT
Voltage
Voltage Range
Frequency
OUTPUT
Output Voltage (AC mode)
Output Voltage (Bat. mode)
Transfer Time
Waveform
BATTERY
Type & Num ber
Charging Time
PROTECTION
Full Protection
PHYSICAL
Dimension (DxWxH mm )
Net Weight (kgs)
ENVIRONMENT
Humidity
Temperature
110/120 VAC or 220/230/240 VAC
90~145 VAC or 180~270 VAC
50 Hz or 60 Hz sam e as input
120 VAC ± 10% / 230 VAC ± 10%
2-6 ms (Typical)
Simulated Sine Wave
12 V/4.5 AH x 1 12 V/ 7 AH x 1 12 V/9 AH x 1
8 hours recover to 90% capacity
Overcharge, discharge, short circuit, and thermal protection
228 x 82.5 x 207
2.2 2.7 3.1
0-90 %
0-40 C (non-condensing)
advertisement
Related manuals
advertisement