Revised

05/04/2006

Getting Started

Index

Choose point to measure “From”

3

4

Choose point to measure “To” 5,6

Selecting points under hood 6

Measuring 7

Calibrate Tram

Follow LCD Screen/Tram Operation

Establish Datum Plane

Measuring To Hole/Bolt 11

Difference Specification/Actual Measurements and Tram Bar 14

8

8,9

10

Setup Tram for Under Hood Measuring

Job/Customer Info

Parts On/Parts Off

Body Openings

Tram Setup

15

16

17

18

19,20,21,22,23

Preferences 23,24,25

Parts and Accessories 26

E-Access Data Synchronization/Help 27

Update/License Update

Frequently Asked Questions

28

29

Getting Started

1

Click the Start New

Measurement Button

5

2

Select Year

Select Body Style

3

Select Make

4

Select Model

6

If correct vehicle is selected, click next.

7

From the Menu, select “Display” click “Tram Measurements”.

8

Note:

Determine the type of damage. This example is a front collision.

Starting point (body zero) will be at the cowl area.

First establish a Datum Plane

Then measure forward from body zero line.

Then the under hood area will be measured

3

Choose reference points to measure “From”

1

Position cursor on reference point to measure From and click.

NOTE: You can select points two different ways

1

2 st nd

Click on point.

Select from drop down box.

NOTE:

Click to remove check for comparison measuring.

Used when specifications do not exist or individual points without specifications.

See Page 23 for Tram setup.

This enters letter designation of reference point measurement From.

Also Height and Width of reference point.

2

Position cursor on reference point to measure To and Click

4

This enters letter designation of reference point measurement

To

Height, Length and Diagonal measurements are automatically added.

3

Click on the Add button to start entering next points to be measured

This starts a new Tab.

4

Position Cursor on reference point to measure From and click.

5

Then click on the reference point to measure To.

5

This enters the specifications for the next Tab, continue steps 2, 3 and 4 until all needed points are selected.

Under Hood Measuring

5

Select the From and To points under hood the same way as under body points.

Note:

You are allowed a total of Ten Tabs.

6

6

Select points to measure by clicking on Tab

Prepare & Calibrate Tram (For Details See Page 8)

7

After calibrating the Tram click on the Tram button to send measurements to Tram.

7

Calibrating the Tram

To Calibrate Tram

:

1. Collapse Tram completely (telescoping section)

2. Slide LCD display box all the way to telescoping end of tram.

3. Install Height Rod and lower to plastic cone.

4. Turn on Tram (this calibrates the Tram)

5.

Press the Scroll Button (Length and Height) will appear in LCD screen

Height Rod Plastic Cone

Send Button

Scroll Button

On/Off Button

Follow LCD Screen information by using the Scroll button.

(RS = Right Side) PS = Passenger Side

(LS = Left Side) DS = Drivers Side

W = Width

L = Length

H = Height

D = Diagonal

S = Strut

MANF = Specifications

MEAS = Actual measurements

DIFF = Difference between specifications and measurements

8

Tram Operation

(measuring)

Select 1 st

Tab

1. Calibrate Tram (see page 10)

2. Install adapters at starting points (Body Zero)

3. Follow steps 1-7 to prepare for measuring.

4. Establishing datum plane (see page 12)

5. Click “Tram” button to send specifications to Tram.

6. With equal length pointers, measure width at adapters (send to computer)

7. Measure the center section height (ds/ps) (send to computer)

8. Measure the center section length (ds/ps) (send to computer)

9. Measure center section diagonal (ds/ps) (send to computer)

10. Click “Tram” button to stop communication with Tram.

Select 2 nd

Tab

1. Click “Tram” button to send specifications to Tram.

2. With equal length pointers, measure width at adapters (send to computer)

3. Measure from adapter to damaged area (sending each to the computer)

• Measure the damaged area height (ds/ps) (send to computer)

• Measure the damaged area length (ds/ps) (send to computer)

• Measure damaged area diagonal (ds/ps) (send to computer)

• Click “Tram” button to stop communication with Tram.

Select 3rd Tab

1. Click “Tram” button to send specifications to Tram.

2. With equal length pointers, measure width at adapters (send to computer)

3. Measure from adapter to damaged area (sending each to the computer)

• Measure the damaged area height (ds/ps) (send to computer)

• Measure the damaged area length (ds/ps) (send to computer)

• Measure damaged area diagonal (ds/ps) (send to computer)

• Click “Tram” button to stop communication with Tram.

9

Establishing Datum Plane

Datum Line- an imaginary straight line below the vehicle from which all height dimensions are referenced. The Rocker panel of a vehicle is parallel to the datum line. Most major pulling and measuring equipment mount the vehicle on to the lower sill flanges and measure up from the platform.

Level

Mount Level on the Tram Bar shoulder screw located on the top of the display box.

Send the data that has been entered in

(Page 4,Steps 1 & 2 )

to the display box by clicking on the “Tram” button.

Adjust the height rod until the Difference column on the display box reads zero. Lock this height by tightening the height set screw. Extend the tram to the point. Touch the tip of the height rod to the surface beside the hole when measuring to a hole. Touch the tip of the height rod to the tip of the bolt head when measuring to a bolt. When tram is positioned, adjust the Level until it becomes level.

This establishes the Datum Plane.

IMPORTANT NOTE:

Remember which direction (Front to Rear) the thumbscrew on the

Vial\Level is facing when creating a datum line. Always keep this direction when measuring.

Following Example is a front-end collision.

Example for establishing a Datum Plane

Direction of level for setting Datum

Example for measuring damaged section.

Direction of level for measuring

10

Measurements “To”

All Height measurements to holes are the surface next to the hole.

When measuring to bolts measure to the center of the bolt head.

Reference “M” to “Q” used to set Datum

Reference Point “M” is

Body Zero line or starting point for measuring.

(From)

11

“To” “From”

Tram Diagonal Measurement

Tram Width Measurement

Tram Length/Datum Measurement

Example “M” to “I”

Example “M” to “H”

12

After measuring first Tab click on the save button.

Continue selecting Tabs and measuring until all the measurements are recorded for Initial.

After repairing the Vehicle and recording the final measurements

13

Clicking the “Diff Button” displays the difference between

Specifications and Actual measurements.

42” Tram bar and control box

Two 30” extension bars

OR

42” Tram bar and control box

One 30” extension bars

14

Two 15” extension bars

Tram setup for under hood measuring

To keep LCD screen right side up rotate pointer.

Replace all metal end with plastic end.

(less magnetic force)

“To B”

Add magnetic pointer to end of height rod.

Adjust Height Rod to

137mm and lock.

Under Hood View

“From E”

Strut Width Measurement

14

Tram Diagonal Measurement

Tram Length/Datum Measurement

Tram Width Measurement

15

When you click “YES” this New

Order Box Information box will appear

Anytime you EXIT the program or Click Save this warning box will appear asking if you want to save

Inter Order & Customer information then select OK.

If Information fields are already filled just select OK

16

Parts ON/Off

Parts On Tab are all removable cross-members etc, (bolt on parts) still on spec sheet

Note: All bolt on parts are Green

Parts Off Tab all bolt on parts removed from spec sheet

17

Body Openings

18

Measuring From Hole To Hole

Magnetized Pointer

Height Rod Cone

Height Rod

Blue Extension

Level

Tram LCD Display Box

Tram Display Box Lock

Red Extension used if added clearance is needed between

Tram and repair equipment.

Add Short Blue Extension

For Measuring From a Bolt

Attachments used From Bolts. See Page 22

19

Setup for measuring From hole To horizontal bolt.

Use when Measuring to a Horizontal Bolt

Important:

Adding Extensions to Tram requires the use of the Adapter Button.

Default setting is Short

Click Adapters Button

Select Long

Add Green Extension to lower tram for measuring around objects

20

Add this Short Extension for

Measuring From a Side Hole

Add this Long Extension for

Measuring From a Side Hole

21

Setup for Measuring

Under Hood

Adjust Height Rod

To 137mm

Reverse Pointer

Add Pointer

For Under Hood

Measuring Attach

Magnetic Adapter to

Bolt.

For Smaller Bolt Insert Spacer

Plastic Spacer for

Under Hood Bolt size

Measuring From Bolts Under Body

Vertex Bolt Attaching Rings

Remove Screws Install Ring to fit bolt

22

Use when to establish datum

Install Magnet Adapter

Setup for using as a tram with equal length pointers.

Setup For Comparison Measuring

Set Height Rod

To 152mm

Install Black Pointer

23

}

When checked information will be printed on report

Enter Shop

Information

Select Com-port Setting

24

CD-Rom Drive

Letter

Location and size of

Electronic File.

Select Language for

Printing Report

Check Information to be printed on report

Browse for

Company Logo

Check Information to show on printed report

25

Check when using VIN

Decoder

1

2

3

Parts and Accessories

4

5 7

6

8 9

2

5

6

7

9

10

11

13

16

17

18

19

21

23

10

13

12

14

17

18

20

19

21

23

24 25 26 27 28 29

22

15

16

11

33

788731 Magnetic Plastic Base

788734 Side Mount Rod (Long)

788735 Side Mount Rod (Short)

788736 Cone Rod (34mm Blue)

788738 Bolt Adapter (2ea)

788739 Cone Rod (152mm Green)

788740 Cone Rod (78mm Blue)

788742 Plastic Spacer (2ea)

788745 Tram Rod (74mm Black)

788746 Height Rod (250mm)

788747 Height Rod (125mm)

788748 Height Rod (62.5mm)

Height Cone

788750 Height Rod (215mm)

788480 Vertex Bolt Attachment Ring Kit

26

30

32

34

31

Ref.

Part No. Description

24 788481 Vertex Bolt Att.Ring,10mm

25 788482 Vertex Bolt Att.Ring,12mm

26 788483 Vertex Bolt Att.Ring,15mm

27 788484 Vertex Bolt Att.Ring,16mm

28 788485 Vertex Bolt Att.Ring,17mm

29 788486 Vertex Bolt Att.Ring,18mm

30 788487 Vertex Bolt Att.Ring,19mm

31 788488 Vertex Bolt Att.Ring,21mm

Extension

Chief E-Access

Requires High-Speed

Internet connection.

Procedures for Chief E-Access:

Note: Requires High-Speed Internet access and valid (site key).

1. To manually update, access File from Main Window.

2. Click Update.

3. Click Chief E-Access Data Synchronization.

4. Follow instructions on screen.

(Requires High-Speed Internet connection)

When a problem stops the repair process and help is needed.

1. From the menu click Help

2. Click on Chief E-Access Help

This allows linking to Tech Support through the internet.

Follow on screen instructions

27

Update:

When new data is available for Computerized Measuring program, it is provided in either 3.5 inch floppy diskette, CD's or Chief E-Access (Internet). Procedures for installing each type follow:

Procedures for Diskette Update:

1. Access Computerized Measuring Main Menu Window.

2. Insert update Diskette into Drive 'A' and select Update from list of items below File heading.

3. Select {bmc CANCELA.BMP} when Computerized Measuring CD Update Dialog Box appears.

4. Select {bmc OK1.BMP} when Computerized Measuring Update Dialog Box appears.

5. Follow instructions on screen.

Procedures for CD Update:

1. Access Computerized Measuring Main Menu Window.

2. Insert CD into CD-Rom Drive and select Update from list of items below File heading.

3. Select {bmc OK1.BMP} when Computerized Measuring CD Update Dialog Box appears.

4. Select Yes when Computerized Measuring Startup Notice Dialog Box appears.

5. When Computerized Measuring Setup/Update Program Dialog Box appears select {bmc

OK1.BMP} to update.

Procedures for Chief E-Access:

Note: Requires High Speed Internet access and valid contract (Site Key).

Updates automatically at pre-set time and date.

1. To manually update access File from Main Menu Window.

2. Click Update.

3. Click Chief E-Access Data Synchronization.

4. Follow instructions on screen.

License Update:

Used to add special features after contacting customer service.

Follow on screen instructions.

28

FCC ID

QTY

JMAMARKOO2

This Device Complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions.

1.) This Device may not cause harmful interference.

2.) This Device must accept any interference received

including interference that may cause undesired operation

Frequently Asked Questions

1. Should the datum plane be established every time a vehicle is measured?

Keep in mind the main purpose of the datum plane is for sheet metal alignment. (door to fender gap or quarter to door line)

Datum is established in the center section, and is a height measurement in the end sections for sheet metal alignment.

Many times a vehicle is involved in a light to medium collision or hit on one side or the other and many times the sheet metal on the undamaged side is aligned correctly. This means that datum is not necessary in this case. Simply adjust the tram level on the good side. And then make the damaged side the same height.

2. Is the calibration of the tram important:

When comparing the length, width and height to specifications it is important that the tram be calibrated.

3. How many points should be measured?

This will depend on the severity of the collision, however keep in mind a damaged vehicle must first be divided into three sections.

And the datum is established in the center section.

The end sections must be divided into two sections, from the center to the suspension and from the suspension to the end of the structure.

4. Should the vehicle be level for measuring?

Remember that a level is used to set the tram to a level (datum) position, so in theory if the vehicle is perfectly level to the world there would be no need to keep the level in the same direction as when the datum was established. However because the vehicle is not perfectly level always keep the thumbscrew on the level pointing the same way when measuring datum.

5. What is the purpose of the two styles of screw on pointers (all metal-silver) (plastic-black).

The all metal one is used under the vehicle for holding the end of the tram in place, the plastic one is used when measuring under hood, less magnetic holding power. (either can be used under hood, however; the metal (silver) pointer used under body).

6. Why are there two extensions for measuring from side hole?

This depends on how far up on the side rail the reference hole is located. The tram must be at a reasonable height for measuring.

7. When in preference section (Quick Entry Setup) what does it mean when “VIN Reader” box is checked?

When clicking on “Start New Measurement”, customer information dialog box will appear first.

When not checked, clicking on “Start New Measurement” accesses Vehicle selection dialog boxes.

8. What numbers should appear in LCD display after calibrating tram?

Length = 0126mm

Height = 0059mm

9. Why is level position important when measuring for the datum plane.

If the vehicle is anchored perfectly level to the world and the pulling equipment is also level, the position of the level is not important, however; perfect level will almost never happen. Observing the position of the level adjusting screw when setting datum, and keeping the level adjusting screw in the same direction (relative to the vehicle) when measuring the damaged section will create a correct datum plane.

29