- Computers & electronics
- Cameras & camcorders
- Film cameras
- Kodak
- C310 - EASYSHARE Digital Camera
- User's Guide
advertisement
Kodak EasyShare C310/CD40 digital camera
FPO
User’s guide
www.kodak.com
For interactive tutorials, www.kodak.com/go/howto
For help with your camera, www.kodak.com/go/c310support or www.kodak.com/go/cd40support
Eastman Kodak Company
Rochester, New York 14650
© Eastman Kodak Company, 2005
All screen images are simulated.
Kodak, EasyShare, and Retinar are trademarks of Eastman Kodak Company.
P/N 4J4295_en
Front view
4
5 6
7
3
2
1
1 Grip
2 Strap post
3 Self Timer/Video light
4 Shutter button
5 Mode dial/Power
6 Flash unit
7 Viewfinder lens
8 Lens
8
Product features www.kodak.com/go/support
i
ii
Product features
Back view
6
3
4
5
7
8
9
2
1
10
11
15
12
13
14
16
1 Tripod socket
2 Dock connector
3 Share button
4 Controller buttons (4)
5 OK button
6 Delete button
7 Viewfinder
8 Ready light
9 Camera screen
(LCD: liquid crystal display)
10 Flash/Status button
11 Grip
12 Slot for optional SD/MMC card
13 Menu button
14 Review button
15 USB (Universal Serial Bus) port
16 Battery compartment
www.kodak.com/go/support
Table of contents
1
1 Setting up your camera .........................................................................1
Setting the language and date/time, other times............................................ 3
Storing pictures on an SD or MMC card ......................................................... 3
2 Taking pictures and videos ....................................................................4
Protecting pictures and videos from deletion................................................ 10
3 Transferring and printing pictures .......................................................12
Transferring pictures with the USB cable...................................................... 13
Dock compatibility for your camera.............................................................. 17
4 Doing more with your camera .............................................................18
Putting yourself in the picture or video......................................................... 18
Viewing picture/video information ............................................................... 28
www.kodak.com/go/support
iii
Table of contents
Camera/computer communications.............................................................. 40
Upgrading your software and firmware........................................................ 56
Additional care and maintenance ................................................................ 56
iv
www.kodak.com/go/support
1
Setting up your camera
Attaching the wrist strap
Loading the batteries
CRV3 lithium
(non-rechargeable)
Ni-MH KAA2HR
(rechargeable)
2-AA lithium, Ni-MH, or oxy-alkaline AA
For information on replacing batteries and extending battery life, see
www.kodak.com/go/support
1
Setting up your camera
Turning on the camera
2
Setting the date/time, first time
At the prompt, press OK.
to change.
for previous/next field.
OK t o accept.
www.kodak.com/go/support
Setting up your camera
Setting the language and date/time, other times
1
2
3
Press Menu.
to highlight Setup Menu then press OK.
to highlight Language or Date/Time
, then press OK.
If setting the date/time: to change.
OK for previous/next field.
to accept.
Storing pictures on an SD or MMC card
Your camera has 16 MB of internal memory. You can purchase an SD or MMC card to conveniently store more pictures and videos.
NOTE: We recommend Kodak SD and MMC cards. When using the card for the first time, format it in this camera before taking pictures (see
SD or MMC card (optional)
Notched corner
CAUTION:
A card can only be inserted one way; forcing it may cause damage. Inserting or removing a card when the Ready light is blinking may damage pictures, card, or camera.
See page 52 for storage capacities. Purchase SD or MMC cards at a dealer of Kodak
products or www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories
www.kodak.com/go/support
3
4
2
Taking pictures and videos
Taking a picture
1
Turn on camera.
2
Frame your subject in the viewfinder or LCD screen.
3
Press the Shutter button to take the picture.
Ready light
4
When the Ready light blinks green, the picture is being saved; you can still take pictures.
Taking a video
1
Turn on camera.
2
Frame your subject in the viewfinder or LCD screen.
3
Press the Shutter button down and release, or press and hold for more than 2 seconds.
The camera does not record audio.
To stop recording, press the
Shutter button again.
www.kodak.com/go/support
Taking pictures and videos
Reviewing the picture or video just taken
After you take a picture or video, the camera LCD screen displays a Quickview for approximately 5 seconds.
While the picture or video and are displayed:
Delete
If you take no action, the picture/video is saved.
OK to play/pause a video
Tag a picture/video for email or as a favorite, or tag a picture for print.
To view pictures and videos anytime, see
.
Using the camera LCD screen as a viewfinder
IMPORTANT: The Liveview feature significantly depletes battery power; use it sparingly.
1 Turn the Mode dial to any Still mode.
2 Press the OK button to turn on the camera screen.
3 Frame your subject in the camera screen.
4 Press the Shutter button to take the picture.
5 To turn off the LCD screen, press the OK button.
OK button
To make the LCD screen turn on whenever the camera is on, see Liveview, page 25
www.kodak.com/go/support
5
Taking pictures and videos
Picture/video capture screens
Self-timer
Date stamp
Flash
Picture quality
Pictures/video time remaining
Image storage location
Album name
Mode description
Zoom:
Telephoto
Wide
Low battery
Capture mode
Exposure compensation
6
Using digital zoom
Use digital zoom in any Still mode to get up to 5X closer to your subject.
IMPORTANT: You may notice a decrease in printed image quality when using digital
zoom. The blue slider on the zoom indicator pauses and turns red when the picture quality reaches the limit for an acceptable 4 x 6 in. (10 x 15 cm) print.
1 Press the OK button to turn on the LCD screen, then press to zoom in.
The LCD screen displays the zoomed image and the zoom indicator.
2 Press to zoom in and out.
3 Press the Shutter button to take the picture.
Zoom indicator
To turn off digital zoom, from the lowest setting, press .
NOTE: You cannot use digital zoom for video recording.
Digital zoom is available only when Liveview is turned on. (See
.)
www.kodak.com/go/support
Taking pictures and videos
Using the flash
Use the flash when you take pictures at night, indoors, or outdoors in heavy shadows.
Flash is effective between 2.6 - 7.9 ft (0.8 - 2.4 m). You can only change the flash setting in Still modes.
Press the button repeatedly to scroll through flash options (see Flash modes table on
The active flash icon is displayed in the
LCD screen status area (see page 6
).
To change the flash settings, see
.
Reviewing pictures and videos
Press the Review button to view and work with your pictures and videos.
Videos:
OK to play/pause
Rewind to beginning (during playback)
Next picture/video (during playback)
1
Review
(
Press again to exit
)
2
(previous/next)
To save battery power, use the optional Kodak EasyShare camera or printer dock.
(See www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories .)
NOTE: Pictures taken at 3.5 MP (3:2) quality setting are displayed at a 3:2 aspect ratio with a black bar at the top of the screen.
www.kodak.com/go/support
7
Taking pictures and videos
What the review icons mean
Print tag/number of prints
Favorite tag
Email tag
Protect
Picture/video number
Image storage location
Scroll arrows
Review mode
Video number
Image storage location
Press OK to
Play or Pause
Review mode
Scroll arrows
8
www.kodak.com/go/support
Taking pictures and videos
Magnifying a picture during review
OK
OK magnify at 2X. Press again for 4X.
view other parts of the picture.
return to 1X
.
Viewing multi-up (thumbnails) during review
view multi-up thumbnails.
view previous/next row of thumbnails.
view previous/next thumbnail.
OK view single picture.
www.kodak.com/go/support
9
Taking pictures and videos
Protecting pictures and videos from deletion
1 Press Review.
2 for previous/next.
3
Press Menu.
4
Press highlight Protect then press OK.
to
,
Note: To cancel Protect, press OK again.
The picture or video is protected and cannot be deleted. The Protect icon appears with the protected picture or video.
Press the Menu button to exit.
CAUTION:
Formatting internal memory or an SD or MMC card deletes all
(including protected) pictures, videos. (Formatting internal memory also deletes email addresses, album names, and favorites. To restore them, see EasyShare software Help.)
10
www.kodak.com/go/support
Taking pictures and videos
Deleting pictures and videos
1
Press Review. (To exit, press
Review again.)
2 for previous/next.
3
Press Delete.
4
Follow the screen prompts.
PICTURE or VIDEO—deletes the displayed picture or video.
EXIT—exits the Delete screen.
ALL—deletes all pictures and videos from your current storage location.
NOTE: To delete protected pictures and videos, remove protection before deleting.
www.kodak.com/go/support
11
3
Transferring and printing pictures
Installing the software
CAUTION:
Install Kodak EasyShare software before connecting the camera or
optional dock to the computer. Failure to do so may cause the software to load incorrectly.
1 Close all software applications that are open on your computer (including anti-virus software).
2 Place the Kodak EasyShare software CD into the CD-ROM drive.
3 Load the software:
Windows OS—if the install window does not appear, choose Run from the Start menu and type d:\setup.exe where d is the drive letter that contains the CD.
Mac OS X—double-click the CD icon on the desktop, then click the Install icon.
4 Follow the on-screen instructions to install the software.
Windows OS—select Complete to automatically install the most commonly used applications. Select Custom to choose the applications you wish to install.
Mac OS X—follow the on-screen instructions.
NOTE: When prompted, register your camera and software. Registering lets you sign up for information that keeps your system up-to-date. To register later, visit www.kodak.com/go/register.
5 If prompted, restart the computer. If you turned off anti-virus software, turn it back on. See the anti-virus software manual for details.
For information on the software applications included on the Kodak EasyShare software CD, click the Help button in the Kodak EasyShare software.
12
www.kodak.com/go/support
Transferring and printing pictures
Transferring pictures with the USB cable
1 Turn off the camera.
2 Plug the labeled end of the USB cable
(model U-8) into the labeled USB port on your computer. See your computer user’s guide for details.
3 Plug the other end of the USB cable into the labeled
USB port on the camera.
4 Turn on the camera.
Kodak EasyShare software opens on your computer.
The software prompts you through the transfer process.
NOTE: Visit www.kodak.com/go/howto for an online tutorial on connecting.
Also available for transferring
â–
â–
You can also use these Kodak products to transfer your pictures and videos.
Kodak EasyShare camera dock, Kodak EasyShare printer dock (see
Kodak multi-card reader, Kodak SD multimedia card reader-writer
Purchase these and other accessories at a dealer of Kodak products or www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories
www.kodak.com/go/support
13
Transferring and printing pictures
Printing pictures
Printing with a Kodak EasyShare printer dock
Dock your camera to the Kodak EasyShare printer dock and print directly—with or without a computer. Purchase this and other accessories at a dealer of Kodak products or www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories
Direct printing with a PictBridge enabled printer
Your camera is compatible with PictBridge technology, so you can print directly to
PictBridge enabled printers. You need:
â–
Camera with fully charged batteries, or with optional Kodak 3-volt AC adapter
â–
â–
PictBridge enabled printer
USB cable (may be sold separately)
Connecting the camera to a PictBridge enabled printer
1 Turn off the camera and printer.
2 Optional: If you have a Kodak 3-volt AC adapter (optional accessory), plug it into the camera and into an electrical outlet.
IMPORTANT: Do not use the AC adapter included with the EasyShare camera dock or
printer dock to power your camera.
3 Connect the appropriate USB cable from the camera to the printer. (See your printer user guide or www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories for details.)
14
www.kodak.com/go/support
Transferring and printing pictures
Printing from a PictBridge enabled printer
1 Turn on the printer. Turn on the camera.
The PictBridge logo is displayed, followed by the current picture and menu. (If no pictures are found, a message is displayed.) If the menu interface turns off, press any button to redisplay it.
2 Press to choose a printing option, then press the OK button.
Current Picture Press
Index Print
to choose a picture. Choose the number of copies.
Tagged Pictures If your printer is capable, print pictures that you tagged for printing and choose a print size.
Print thumbnails of all pictures. This option requires one or more sheets of paper. If the printer is capable, choose a print size.
All Pictures
Print all pictures in internal memory, on a card, or in Favorites.
Choose the number of copies.
Image Storage
Access internal memory, a card, or Favorites.
NOTE: During direct printing, pictures are not permanently transferred or saved to the computer or printer.
To transfer pictures to your computer, see
. In Favorites mode, the current favorite picture is displayed.
www.kodak.com/go/support
15
Transferring and printing pictures
Disconnecting the camera from a PictBridge enabled printer
1 Turn off the camera and printer.
2 Disconnect the USB cable from the camera and the printer.
Using a printer that is not PictBridge enabled
For details on printing pictures from your computer, click the Help button in the Kodak
EasyShare software.
Ordering prints online
â–
â–
â–
â–
Kodak EasyShare Gallery ( www.kodakgallery.com
) is one of the many online print services offered in the Kodak EasyShare software. You can easily:
Upload your pictures.
Edit, enhance, and add borders to your pictures.
Store pictures, and share them with family and friends.
Order high-quality prints, photo greeting cards, frames, and albums—and have them delivered to your door.
Printing from an optional SD or MMC card
â– Automatically print tagged pictures when you insert your card into a printer with an SD/MMC card slot. See your printer user’s guide for details.
â– Make prints at an SD/MMC card-capable Kodak picture maker. (Contact a location prior to visiting. See www.kodak.com/go/picturemaker .)
â– Take the card to your local photo retailer for professional printing.
16
www.kodak.com/go/support
Transferring and printing pictures
Dock compatibility for your camera
Docking configuration Kodak EasyShare dock
â–
â–
â–
â– printer dock printer dock plus printer dock 6000 camera dock 6000
Custom dock insert
Kodak dock adapter kit D-22
Dock
â– others, including series 3 printer docks and camera docks
Custom dock insert
Dock
â–
â–
â– printer dock 4000 camera dock II
LS420, LS443 camera dock
Not compatible
Purchase camera docks, printer docks, and other accessories at a dealer of Kodak products or www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories
www.kodak.com/go/support
17
18
4
Doing more with your camera
Putting yourself in the picture or video
The Self Timer creates a 10- or 2-second delay between the time you press the Shutter button and the time the picture or video is taken.
1 Turn the Mode dial to any Still mode for pictures, or to for videos, then press the Menu button.
2 Press to highlight Self Timer , then press the OK button.
3 Highlight 10 or 2 seconds, then press the OK button.
4 Press the Menu button to turn off the menu screen.
The Self Timer icon and delay time appear in the status area.
5 Place the camera on a flat surface or use a tripod.
6 Compose the scene.
Press the Shutter button, then move so that you are in the scene.
If the Self Timer is set at 10 seconds, the Self Timer light blinks slowly for 8 seconds
(then quickly for 2 seconds) before the picture or video is taken.
If the Self Timer is set at 2 seconds, the light blinks for 2 seconds before the picture or video is taken.
The Self Timer cancels after you take the picture, record the video, or turn off the camera.
NOTE: The video stops when you press the Shutter button or when no storage space remains.
www.kodak.com/go/support
Doing more with your camera
Running a slide show
Use the Slide Show to display your pictures and videos on the LCD screen.
To run a slide show on a television or on any external device, see
Starting the slide show
1 Press the Review button, then press the Menu button.
2 Press to highlight Slide Show , then press the OK button.
3 Press to highlight Begin Show, then press the OK button.
Each picture and video is displayed once, in the order in which you took them.
4 To cancel the Slide Show, press the OK button.
Changing the slide show display interval
The default interval setting displays each picture for 5 seconds. You can set the display interval from 3 to 60 seconds.
1 On the Slide Show menu, press
OK button.
to highlight Interval, then press the
2 Select a display interval.
To scroll through the seconds quickly, press and hold
3 Press the OK button.
The interval setting remains until you change it.
.
www.kodak.com/go/support
19
Doing more with your camera
Running a continuous slide show loop
When you turn on Loop, the slide show is continuously repeated.
1 On the Slide Show menu, press to highlight Loop, then press the OK button.
2 Press to highlight On, then press the OK button.
The slide show repeats until you press the OK button or until battery power is exhausted. This setting remains until you change it.
Displaying pictures and videos on a television
You can display pictures and videos on a television, computer monitor, or any device equipped with a video input using a compatible Kodak EasyShare printer dock and an optional audio/video cable (see the printer dock user’s guide).
Purchase these and other accessories at a dealer of Kodak products or at www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories
Copying pictures and videos
You can copy pictures and videos from a card to internal memory or from internal memory to a card.
Before you copy, make sure that:
â– A card is inserted in the camera.
â– The camera’s picture storage location is set to the location from which you are copying. See
.
20
www.kodak.com/go/support
Doing more with your camera
Copy pictures or videos:
1 Press the Review button, then press the Menu button.
2 Press to highlight Copy , then press the OK button.
3 Press to highlight an option.
4 Press the OK button.
NOTE: Pictures and videos are copied, not moved. To remove pictures and videos from the original location
after copying, delete them (see page 10 ).
Tags that you applied for print, email, and favorites are not copied. Protection settings are not
copied. To apply protection to a picture or video, see page 10
.
www.kodak.com/go/support
21
Doing more with your camera
Choosing a flash setting
Flash button
Press the button repeatedly to scroll through flash options
(see Flash modes table).
The current flash mode is shown in the
LCD status area.
â–
â–
NOTE:
Off and Fill flash options revert to Auto when the camera is turned off.
When the picture is taken with Auto or Fill flash selected, the camera flashes twice: once to set the exposure and once to take the picture.
Flash modes
Auto
Flash
Fill
Flash fires
When the lighting conditions require it.
Every time you take a picture, regardless of the lighting conditions. Use when the subject is in shadow or is “backlit” (when the sun is behind the subject).
Red-eye Three times: once to set the exposure, once to reduce red-eye, and once to take the picture.
Off
Flash never fires.
22
www.kodak.com/go/support
Doing more with your camera
Changing picture-taking settings
You can change settings to get the best results from your camera:
1 In any mode, press the Menu button.
2 Press to highlight the setting you wish to change, then press the OK button.
3 Choose an option, then press the OK button.
4 Press the Menu button to exit.
Setting
Self Timer
Put yourself in the picture or video.
Icon Options
10, 2 seconds, Off.
Exposure Compensation
(Still modes)
Choose how much light enters the camera.
This setting remains until you turn the Mode dial.
-2.0 to +2.0.
If pictures are too dark, increase the value.
If pictures are too light, decrease the value.
www.kodak.com/go/support
23
Doing more with your camera
Setting
Picture Size
(Still modes)
Set picture resolution.
This setting remains until you change it.
Icon
Color Mode
(Still modes)
Choose color tones.
This setting remains until you turn the Mode dial.
Image Storage
Choose an image storage location.
This setting remains until you change it.
Options
4.0 MP (default)—for printing up to
20 x 30 in. (51 x 76 cm); pictures are highest resolution and largest file size.
3.5 MP (3:2 Best)—ideal for printing
4 x 6 in. (10 x 15 cm) prints without cropping. Also for printing up to
20 x 30 in. (51 x 76 cm); some cropping may result due to the 3:2 aspect ratio.
3.1 MP (Better)—for printing up to
11 x 14 in. (28 x 36 cm); pictures are medium resolution with smaller file size.
2.1 MP—for printing up to 8 x 10 in.
(20 x 25 cm); pictures are medium resolution with smaller file size.
1.1 MP—for printing up to 5 x 7 in.
(13 x 18 cm); for emailing, Internet, or screen display; pictures are lowest resolution and smallest file size.
Color (default)—for color pictures.
Black & White—for black-and-white pictures.
Sepia—for pictures with a reddish-brown, antique look.
Auto (default)—the camera uses the card if one is in the camera. If not, the camera uses internal memory.
Internal Memory—the camera always uses internal memory, even if a card is installed.
24
www.kodak.com/go/support
Setting
Set Album
Choose Album names.
Doing more with your camera
Icon Options
On or Off.
Pre-select album names before you take pictures or videos. Then, all the pictures or videos you take are tagged with those
Video Length
(Video mode)
Choose the amount of recording time for videos.
This setting remains until you change it.
Continuous (default)— as long as there is room on the card or internal memory, or until the Shutter button is pressed.
5, 15, or 30—seconds
NOTE: If the current image storage location does not have adequate space, some video length options are not displayed.
See
page 52 for storage capacities.
See Customizing your camera, page 25 .
Setup Menu
Choose additional settings.
Customizing your camera
Use Setup to customize your camera settings.
1 In any mode, press the Menu button.
2 Press to highlight Setup , then press the OK button.
3 Press to highlight the setting you wish to change, then press the OK button.
4 Choose an option, then press the OK button.
www.kodak.com/go/support
25
Doing more with your camera
5 Press the Menu button to exit.
Setting
Return
Return to previous menu.
Liveview
Change the LCD screen setting so that it is always on or always
This setting remains until you change it.
Auto Power Off
Select when you would like the camera to turn off.
Date & Time
Set the date and time.
This setting remains until you change it.
Video Out
Choose the regional setting that lets you connect the camera to a television or other external
This setting remains until you change it.
Date Stamp
(Still modes)
Imprint the date on pictures.
This setting remains until you change it.
Icon
On or Off.
Options
3 minutes (default)
1, 3, 5, or 10 minutes
See
.
NTSC (default)—used in most countries except those in Europe and China. North
America and Japan use NTSC.
PAL—used in Europe and China.
Turn the Date Stamp on or off, or change the date stamp format.
26
www.kodak.com/go/support
www.kodak.com/go/support
Doing more with your camera
Setting
Video Date Display
(Video mode)
Display capture date and time before the video starts.
This setting remains until you change it.
Language
Display the camera screen text in different languages.
This setting remains until you change it.
Format
Format camera memory.
Icon Options
Choose None, or choose a date and time format.
See
.
Memory Card—deletes everything on the card; formats the card.
Cancel—exits without making a change.
Internal Memory—deletes everything in internal memory including email addresses, album names, and Favorites: formats the internal memory.
CAUTION:
Formatting deletes all pictures and videos, including those that are protected.
Removing a card during formatting may damage the card.
About
View camera and firmware information.
27
Doing more with your camera
Viewing picture/video information
1 Press the Review button, then press the Menu button.
2 Press to highlight Picture or Video Info, then press the OK button.
3 To view information on the next or previous picture or video, press .
4 Press the Menu button to exit.
Changing optional review settings
In Review mode, press the Menu button to access optional review settings.
Magnify (pictures) ( page 10 ) Protect ( page 11 )
Album (
Multi-up ( page 10 )
Copy (
)
Image Storage (
Picture/Video Information ( page 28 )
Pre-tagging for album names
Use the Set Album (Still or Video) feature to pre-select album names before you take pictures or videos. Then, all the pictures or videos you take are tagged with those album names.
First—on your computer
Use Kodak EasyShare software to create album names on your computer. Then copy up to 32 album names to the album name list on your camera the next time you connect the camera to the computer. See Kodak EasyShare software Help for details.
28
www.kodak.com/go/support
Doing more with your camera
Second—on your camera
1 In any mode, press the Menu button.
2 Press to highlight Set Album , then press the OK button.
3 Press to highlight an album name, then press the OK button. Repeat to mark pictures or videos for albums.
Selected albums are noted with a check mark.
4 To remove a selection, highlight an album name and press the OK button. To remove all album selections, select Clear All.
5 Highlight Exit, then press the OK button.
Your selections are saved. If you turn on the LCD screen, your album selection is displayed on the screen. A plus (+) after the album name means more than one album is selected.
6 Press the Menu button to exit.
This setting remains until you change it.
Third—transfer to your computer
When you transfer the tagged pictures and videos to your computer, Kodak EasyShare software opens and categorizes your pictures and videos in the appropriate album.
See the Kodak EasyShare software Help for details.
Tagging pictures/videos for albums
Use the Album feature in Review mode to tag the pictures and videos in your camera with album names.
First—on your computer
Use Kodak EasyShare software to create album names on your computer, then copy up to 32 album names to the camera’s internal memory. See Kodak EasyShare software Help for details.
Second—on your camera
www.kodak.com/go/support
29
Doing more with your camera
1 Press the Review button.
2 Press to locate a picture, then press the Menu button.
3 Press to highlight Album , then press the OK button.
4 Highlight an album, then press the OK button.
The album name appears with the picture. A plus (+) after the album name means the picture was added to more than one album.
To add other pictures to the same album, press to scroll through the pictures.
When the picture you want is displayed, press the OK button.
To add the pictures to more than one album, repeat step 4 for each album.
5 To remove a selection, highlight an album name, then press the OK button. To remove all album selections, select Clear All.
6 Highlight Exit, then press the OK button.
Your selections are saved.
1 Press the Menu button to return to Review mode.
Third—transfer to your computer
When you transfer the tagged pictures and videos to your computer, Kodak EasyShare software opens and categorizes your pictures and videos in the appropriate album.
See Kodak EasyShare software Help for details.
30
www.kodak.com/go/support
Doing more with your camera
Sharing your pictures
Press the Share button to tag your pictures and videos.
When they are transferred to your computer, you can share using:
Print (
)
Pictures Videos
✔
✔ ✔
Favorites (
for easy organization on your computer and for sharing on your camera
✔
NOTE: Tags remain until removed. If a tagged picture or video is copied, the tag is not copied.
✔
Tagging pictures for printing
1 Press the Share button.
2 Press
3 Press
to locate a picture.
to highlight Print , then press the OK button.*
4 Press to select the number of copies (0 - 99). The default is one. Zero removes the tag for that picture.**
The Print icon appears in the status area.
5 Press the OK button.
www.kodak.com/go/support
31
Doing more with your camera
6 Press the Share button to exit.
* To tag all pictures in the image storage location, highlight Print All , press the OK button, then select the number of copies as described above. Print All is not available in Quickview.
**To remove the print tagging for all pictures in the image storage location, highlight
Cancel Prts , then press the OK button. You cannot cancel prints in Quickview.
Printing tagged pictures
When you transfer the tagged pictures to your computer, the Kodak EasyShare software print screen opens. For details, click the Help button in the Kodak EasyShare software.
For more information on printing from your computer or card, see
NOTE: For the best 4 x 6 in. (10 x 15 cm) prints, set the camera to 3.5MP (3:2) print quality setting.
Tagging pictures and videos for emailing
First—on your computer
Use Kodak EasyShare software to create an email address book on your computer.
Then, copy up to 32 email addresses to the camera’s internal memory.
Second—tag pictures/videos on your camera
1 Press the Share button. Press to locate a picture/video.
2 Highlight Email , then press the OK button.
3 Highlight an email address, then press the OK button.
To tag other pictures/videos with the same address, press to scroll through the pictures. When the picture or video you want is displayed, press the OK button.
To send the pictures/videos to more than one address, repeat step 2 for each address.
Selected addresses are checked.
32
www.kodak.com/go/support
Doing more with your camera
4 To remove a selection, highlight a checked address and press the OK button. To remove all email selections, highlight Clear All.
5 Highlight Exit, then press the OK button.
Your selections are saved. The Email icon appears in the status area.
6 Press the Share button to exit.
Third—transfer and email
When you transfer the tagged pictures/videos to your computer, the Email screen opens and lets you send them to the addresses you specified. For details, click the
Help button in the Kodak EasyShare software.
Tagging pictures as favorites
You can preserve your favorite pictures in the Favorites section of your camera’s internal memory, then share them with friends and family.
NOTE: When you transfer pictures from your camera to your computer, all pictures (including favorites) are stored on your computer at full size. Favorite pictures—smaller copies of your originals—are loaded back to your camera, so you can share and enjoy more.
Share your favorite pictures in 4 easy steps:
1. Take pictures
2. Tag pictures as favorites
1
Press the Share button. Press to locate a picture.
2
Press to highlight Favorite , then press the OK button.
The Favorite icon appears in the status area. To remove the tag, press the OK button again.
Press the Share button to exit the menu.
www.kodak.com/go/support
33
Doing more with your camera
3. Transfer pictures to your computer
1
To enjoy full functionality, install and use the EasyShare software
that was packaged with this camera. (See page 12 .)
2
Connect the camera to the computer using the USB cable (see
) or an EasyShare dock.
The first time you transfer pictures, the software helps you make choices about your favorite pictures. Then, your pictures are transferred to the computer. Favorite pictures (smaller versions of the originals) are loaded to the Favorites section of your camera’s internal memory.
4. View favorites on your camera
1
Turn the Mode dial to Favorites .
2
Press to scroll through favorites.
To exit Favorites mode, turn the Mode dial to any other position.
NOTE: The camera holds a limited number of favorites. Use Camera Favorites in the EasyShare software to customize the size of your camera Favorites section. Videos tagged as favorites remain in the
Favorites folder in the EasyShare software. For more details, click the Help button in the Kodak
EasyShare software.
Optional settings
In Favorites mode, press the Menu button to access optional settings.
Slide Show (
) Picture Information (
)
Multi-up (
Remove all favorites (
)
Setup Menu (
NOTE: Pictures taken at the 3.5 MP (3:2) quality setting are displayed at a 3:2 aspect ratio with a black bar at the top of the screen. (See
Picture Size (Still modes), page 24 .)
34
www.kodak.com/go/support
Doing more with your camera
Removing all favorites from your camera
1 Turn the Mode dial to Favorites .
2 Press the Menu button.
3 Highlight , then press the OK button.
All pictures stored in the Favorites section of internal memory are removed. Favorites are restored the next time you transfer pictures to the computer.
4 Press the Menu button to exit the menu.
Preventing favorites from transferring to the camera
1 Open the Kodak EasyShare software. Click the My Collection tab.
2 Go to the Albums view.
3 Click the Camera Favorites Album for your camera.
4 Click Remove Album.
The next time you transfer pictures from your camera to the computer, use the Camera
Favorites Wizard/Assistant in the Kodak EasyShare software to either recreate your
Camera Favorites Album or to turn off the Camera Favorites feature.
Printing and emailing favorites
1 Turn the Mode dial to Favorites . Press to locate a picture.
2 Press the Share button.
3 Highlight Print or Email , then press the OK button.
NOTE: Favorites that were taken on this camera (not imported from another source) are good for prints up to 4 x 6 in. (10 x 15 cm).
www.kodak.com/go/support
35
36
5
Troubleshooting
For step-by-step product support, visit www.kodak.com/go/c310support or www.kodak.com/go/cd40support and select Interactive Troubleshooting & Repairs.
Camera problems
Problem
Camera does not turn on.
Camera does not turn off.
Pictures remaining number does not decrease after taking a picture.
Cause
Batteries are not installed correctly.
Solution
Install new batteries (
charge rechargeable batteries.
Camera has locked up.
Remove the battery, then reinsert or replace it. If the camera still does not function, contact Customer Support
Picture does not take up enough space to decrease the number.
The camera is operating normally.
Continue taking pictures.
Short battery life with Kodak Ni-MH rechargeable digital camera batteries.
Dirt or oxidation on the battery contacts.
Stored pictures are corrupted.
Card was removed or the batteries expired while the ready light was blinking.
Wipe the contacts with a clean, dry cloth (
) before loading batteries in the camera.
Retake picture. Do not remove card while the ready light is blinking. Keep rechargeable batteries charged.
www.kodak.com/go/support
Troubleshooting
Problem Cause
In Review mode, you do not see a picture (or the expected picture) on the LCD screen.
Camera may not be accessing the correct image storage location.
Solution
Check the image storage location setting (
In Review mode, a blue or black screen is displayed instead of a picture.
File format is unrecognized.
Transfer the picture to the computer
Shutter button does not work.
Camera is not turned on. Turn on the camera (
Camera is processing a picture; the ready light
(near the viewfinder) is blinking red.
Wait until the ready light stops blinking red before attempting to take another picture.
Card or internal memory is full.
Transfer pictures to the computer
( page 13 ), delete pictures from the
camera (
), switch image storage locations (
a card with available memory
.
Shutter button was not pressed.
Slide show does not run on external video device.
Video Out setting is incorrect.
External device is set incorrectly.
Adjust the camera Video Out setting
(NTSC or PAL,
).
See the external device’s user’s guide.
www.kodak.com/go/support
37
Troubleshooting
Problem Cause
Picture is too light.
Subject was too close for flash.
Move so there is at least 2.6 ft (0.8 m) between camera and subject.
Too much light.
Solution
Decrease Exposure Compensation
Clean the lens (
).
Picture is not clear. Lens is dirty.
Subject too close when taking picture.
Move so there is at least 2.6 ft (0.8 m) between the camera and the subject.
Subject or the camera moved while the picture was taken.
Place the camera on a flat, steady surface or use a tripod.
Picture is too dark.
Flash is not on.
Turn on the flash (
).
Subject is too far away for the flash to be effective.
Subject is in front of a bright light (backlit).
Move so there is no more than 7.9 ft
(2.4 m) between the camera and the subject.
Use Fill flash ( page 22 ) or change your
position so light is not behind the subject.
Not enough light.
Increase Exposure Compensation
Purchase a certified SD/MMC card.
Camera does not recognize SD/MMC card.
Card may not be
SD/MMC certified.
Card may be corrupt.
Card is not properly inserted in camera.
Reformat the card ( page 27 ).
Caution: Formatting a card deletes all pictures and videos, including protected files.
Insert a card into the slot, then push to seat (
).
38
www.kodak.com/go/support
Troubleshooting
Problem
Camera freezes up when a card is inserted or removed.
Cause
Camera detected an error when the card was inserted or removed.
Memory card full.
Storage is full.
Solution
Turn the camera off, then back on.
Make sure the camera is turned off before inserting or removing a card.
Insert a new card ( page 3 ), transfer
pictures to the computer ( page 13 ), or
delete pictures (
Maximum number of files or folders is reached (or other directory concern).
Transfer pictures to the computer
( page 13 ), then format the card or
internal memory (
).
Caution: Formatting a card deletes all pictures and videos, including protected files.
www.kodak.com/go/support
39
Troubleshooting
Camera/computer communications
Problem Cause Solution
The computer does not communicate with the camera.
There is a problem with the configuration of the
USB port on the computer.
See this file on the EasyShare software
CD: USB.html Or, visit www.kodak.com/go/ camerasupport
Camera power is off.
Turn on the camera (
Batteries are exhausted or are not charged.
Install new batteries (
charge rechargeable batteries.
Some Advanced Power
Management utilities on laptops turn off ports to save battery life.
See the Power Management section of the laptop user’s guide to disable this feature.
USB cable is not securely connected.
Connect cable to camera and computer port (
).
Software is not installed.
Install the software (
).
Software is installed incorrectly.
The Battery Monitor or similar software runs constantly.
Disconnect the USB cable. Close all open applications. Re-install the software (
Too many applications are running on the computer.
Disconnect camera from the computer.
Close all software applications, reconnect camera.
Close that software before starting the
Kodak software.
40
www.kodak.com/go/support
Troubleshooting
Problem Cause Solution
Cannot transfer pictures.
Software is not installed.
Disconnect USB cable. (If using camera dock or printer dock, disconnect cable
(The Add New
Hardware Wizard cannot locate drivers.)
Software is installed incorrectly.
and remove camera from dock). Close all open applications. Re-install the software (
Disconnect the USB cable. Close all open applications. Re-install the software (
LCD screen messages
Message Cause
Memory card requires formatting
Memory card cannot be read (Please format memory card or insert another card)
Card is corrupted or formatted for another digital camera.
Solution
No images to display There are no pictures in the current image storage location.
Change image storage location setting (
Caution: Formatting a card deletes all pictures and videos, including protected files.
Only one USB connection allowed.
Disconnect cable or rem. (remove) camera from dock.
USB cable is connected to camera while docked.
Unplug the USB cable from the camera.
www.kodak.com/go/support
41
Troubleshooting
Message
Internal memory requires formatting
Internal memory cannot be read (Please format internal memory)
Cause
Camera internal memory is corrupted.
Solution
Format the internal memory
Caution: Formatting deletes all pictures and videos, including protected files.
(Formatting internal memory also deletes email addresses, album names, and Favorites.
To restore them, see the
Kodak EasyShare software
Help.)
No memory card (Files not copied)
There is no card in the camera. Pictures were not copied.
Insert a card (
Not enough space to copy files (Files not copied)
There is not enough space in the image storage location you are copying to (internal memory or the card).
Delete pictures from the image storage location you are copying to
( page 11 ), or insert a new card
).
Memory card is locked
(Insert new memory card)
Read-only memory card.
Card is write-protected.
Insert a new card ( page 3 ), move
the switch on the card to unlock the card, or change the image storage location to internal
Remove write protection to capture or write to card.
42
www.kodak.com/go/support
Troubleshooting
Message
Memory card is unusable (Insert new memory card)
Cause Solution
Card is slow, corrupted, or unreadable.
Insert a new card ( page 3 ) or
Caution: Formatting a card deletes all pictures and videos, including protected
files.
Date and time have been reset
This is the first time you turned on the camera; or the batteries have been removed for an extended period of time; or the batteries are exhausted.
Reset the clock (
No address book on camera (Connect with computer to import address book)
No Email addresses appear because there is no address book.
Create and copy address book from computer. See the Kodak
EasyShare software Help.
No album names on camera (Connect with computer to import album names)
Album names have not been copied to the camera from the computer.
Create and copy album names from computer. See the Kodak
EasyShare software Help.
Can only mark image with 32 album names.
Only the first 32 album names will be saved
The maximum number of album names (32) have been associated with an image.
NOTE: Albums previously associated with an image persist even though they may not be contained in current album file on camera.
Delete one or more album names associated with the image
www.kodak.com/go/support
43
Troubleshooting
Message Cause Solution
High camera temperature. (Camera will be turned off.)
Internal temperature of the camera is too high for the camera to operate.
The viewfinder light glows red and the camera turns off.
Leave the camera off until it’s cool to the touch, then turn it back on.
If the message reappears, contact
Customer Support (
).
Unrecognized file format
Camera cannot read the picture format.
Camera error #XXXX.
See user’s guide.
An error is detected.
Transfer the picture to the
computer ( page 13 ), or delete it
Turn the Mode dial off, then back on. If the message reappears, contact Customer Support
Camera ready light status
Status
Ready light does not turn on and the camera does not work.
Cause Solution
Camera is not turned on. Turn on the camera (
Batteries are exhausted or are not charged.
Install new batteries (
charge rechargeable batteries.
Mode dial was on when batteries were reloaded.
Turn Mode dial off, then back on.
Ready light blinks green.
Ready light blinks amber.
Picture is being processed and saved to the camera.
Camera is operating normally.
Flash is not charged.
Camera is initializing.
Wait. Resume picture taking when the light stops blinking and turns green.
44
www.kodak.com/go/support
Troubleshooting
Status Cause
Ready light blinks red and camera turns off.
Batteries are low or exhausted.
Solution
Install new batteries (
charge rechargeable batteries.
Ready light glows steady red.
Ready light glows steady green.
Camera’s internal memory or card is full.
Camera processing memory is full.
Card is read-only.
Camera is on; ready to take a picture or video.
Transfer pictures to the computer
), delete pictures from the camera (
storage locations (
), or insert a card with available memory
Wait. Resume picture taking when the light turns green.
Change the image storage location
to internal memory ( page 24 ), or use
a different card.
Camera is operating normally.
www.kodak.com/go/support
45
46
6
Getting help
Helpful Web links
Help with your camera
Get support for cameras, software, accessories, more
Purchase camera accessories www.kodak.com/go/c310support www.kodak.com/go/cd40support www.kodak.com/go/pcbasics Help with Windows operating system and working with digital pictures
Download the latest camera software and firmware www.kodak.com/go/c310downloads www.kodak.com/go/cd40downloads
Optimize your printer for truer, more vibrant colors www.kodak.com/go/onetouch www.kodak.com/go/support www.kodak.com/go/c310accessories www.kodak.com/go/cd40accessories
Register your camera
View online tutorials www.kodak.com/go/register www.kodak.com/go/howto
Software help
Click the Help button in the Kodak EasyShare software. Also, see the tutorial on the
CD for help with connecting your camera to a computer.
Telephone customer support
If you have questions concerning the operation of the software or camera, you may speak with a customer support representative.
www.kodak.com/go/support
Getting help
Before you call
Have the camera, camera dock, or printer dock connected to your computer. Be at your computer, and have the following information available:
â–
â–
â–
â–
Operating system
Processor speed (MHz)
Computer model
Amount of memory (MB)
â–
â–
â–
Exact error message you received
Version of Kodak EasyShare software CD
Camera serial number
NOTE: See next page for customer support numbers.
www.kodak.com/go/support
47
Getting help
Australia
Austria
Belgium
Brazil
Canada
China
Denmark
Ireland
Finland
France
Germany
Greece
Hong Kong
India
Italy
1800 147 701
0179 567 357
02 713 14 45
0800 150000
1 800 465 6325
800 820 6027
3 848 71 30
01 407 3054
0800 1 17056
01 55 1740 77
069 5007 0035
00800 44140775
800 901 514
91 22 617 5823
02 696 33452
Netherlands
New Zealand
Norway
Philippines
Poland
Portugal
Singapore
Spain
Sweden
Switzerland
Taiwan
020 346 9372
0800 440 786
23 16 21 33
1 800 1 888 9600
00800 4411625
021 415 4125
800 6363 036
91 749 76 53
08 587 704 21
01 838 53 51
0800 096 868
Thailand
Turkey
001 800 631 0017
00800 448827073
United Kingdom 0870 243 0270
United States 1 800 235 6325
585 781 6231 (toll)
International Toll Line +44 131 458 6714 Japan 03 5540 9002
Korea 00798 631 0024 International Toll Fax +44 131 458 6962
For the most up-to-date listings, visit: http://www.kodak.com/go/dfiswwcontacts
48
www.kodak.com/go/support
7
Appendix
Camera specifications
For more specifications, visit www.kodak.com/go/c310support or www.kodak.com/go/cd40support .
Kodak EasyShare C310/CD40 digital camera
CCD (charge-coupled device)
CCD
Output image size
1/2.5 in. CCD, 4:3 aspect ratio
2304 x 1728 (4.0 M) pixels
2304 x 1536 (3.5 M) pixels
2048 x 1536 (3.1 M) pixels
1664 x 1248 (2.1 M) pixels
1216 x 912 (1.1 M) pixels
Displays
Color display
Preview
Lens
1.6 in. (4 cm) color hybrid LCD, 220 x 279 (61K) pixels
Frame rate: 20 fps; Field-of-view: 99%.
Taking lens
Focus system
Digital zoom
Aspheric all-glass Kodak Retinar lens, f/4.5
35 mm (35 mm equivalent)
Fixed focus. Working range: 0.85 m to infinity
1.0X–5X with 0.2X step
Not supported for movie capture
Integrated in lens barrel Lens barrier
Exposure
Exposure metering TTL-AE, Center-weighted
www.kodak.com/go/support
49
Appendix
Kodak EasyShare C310/CD40 digital camera
Exposure compensation +/-2.0 EV with 0.5 EV step
Shutter speed Mechanical with CCD electrical
Auto: 1/2 - 1/2000 sec.
Auto: 100 to 400 ISO speed
Flash
Electronic flash
Flash modes
Capture
Guide no. 9 (@ ISO 100)
Auto flash by pre-flash
Working range @ ISO 140: 0.8 - 2.4 m
Auto, Fill, Red-eye, Off
Capture modes
Video capture
Image file format
Image storage
Auto, Video
QVGA (320 x 240) @ 20 fps
Still: EXIF 2.2 (JPEG compression)
Optional MMC or SD Card
SD Card Association.)
. (The SD logo is a trademark of the
16 MB internal memory/13 MB available for image storage
(1 MB equals one million bytes)
Internal storage capacity
Review
Quickview
Video output
Yes
NTSC or PAL, selectable via dock connector
50
www.kodak.com/go/support
Appendix
Kodak EasyShare C310/CD40 digital camera
Power
2 Kodak oxy-alkaline digital camera batteries AA ZR6 (non-rechargeable); 2-AA lithium digital camera batteries; 2 Kodak Ni-MH rechargeable digital camera batteries AA; 1 Kodak lithium digital camera battery CRV3 (non-rechargeable); 1 Kodak Ni-MH rechargeable digital camera battery KAA2HR
Communication with computer
USB 2.0 (PIMA 15740 protocol), via USB cable Model U-8, EasyShare camera dock or printer dock
Other features
PictBridge support
Self-timer
Auto power off
Color modes
Date stamp
Yes
10 seconds, 2 seconds selectable
Selectable 1, 3, 5, 10 minutes
Color, Black & White, Sepia
None, YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY
Tripod mount 1/4 inch
Operating temperature 32-104
°
F (0-40
°
C)
Size 4.1 in. (103.5 mm) x 2.6 in. (65 mm) x 1.4 in. (35 mm) @ power off
Weight 4.7 oz (134 g) without battery or card
www.kodak.com/go/support
51
Appendix
Storage capacities
Actual storage capacity varies depending on subject composition, card brand, and other factors. You may be able to store more or fewer pictures and videos. Favorites take up additional space in internal memory.
Picture storage capacity
16 MB internal memory
16 MB SD or MMC
32 MB SD or MMC
64 MB SD or MMC
128 MB SD or MMC
256 MB SD or MMC
Video storage capacity
Number of pictures
4.0 MP 3.5 MP
(3:2)
3.1 MP 2.1 MP 1.1 MP
16
19
38
77
18
21
43
85
20
24
47
95
29
34
68
136
48
56
112
223
153
307
171
341
190
379
272 447
543 893
16 MB internal memory
16 MB SD or MMC
32 MB SD or MMC
64 MB SD or MMC
128 MB SD or MMC
256 MB SD or MMC
Minutes/seconds of video
QVGA (320 x 240)
35 sec.
40 sec.
1 min. 21 sec.
2 min. 42 sec.
5 min. 25 sec.
10 min. 50 sec.
52
www.kodak.com/go/support
Appendix
Power-saving features
If no action for The camera
1 minute Screen turns off.
3 minutes or select
1, 5, or 10 minutes
Enters auto power off.
To turn it back on
Press any button.
Turn the Mode dial off and on again.
Important safety instructions
Using this product
â– Read and follow these instructions before using Kodak products. Always follow basic safety procedures.
â– Use only a USB 2.0 certified computer equipped with a current-limiting motherboard. Contact your computer manufacturer if you have questions.
â– The use of an accessory attachment that is not recommended by Kodak, such as an
AC adapter, may cause fire, electric shock, or injury.
â– If using this product in an airplane, observe all instructions of the airline.
CAUTION:
Do not disassemble this product; there are no user-serviceable parts inside. Refer servicing to qualified service personnel. Do not expose this product to liquid, moisture, or extreme temperatures.
Kodak AC adapters and battery chargers are intended for indoor use only. The use of controls, adjustments, or procedures other than those specified herein may result in exposure to shock and/or electrical or mechanical hazards. If the LCD breaks, do not touch the glass or liquid. Contact Kodak Support.
www.kodak.com/go/support
53
Appendix
Battery safety and handling
â–
CAUTION:
When removing batteries, allow them to cool first; batteries may be hot.
Read and follow all warnings and instructions supplied by the battery manufacturer.
â–
â–
â–
Use only batteries that are approved for this product.
Keep batteries out of the reach of children.
â–
Do not allow batteries to touch metal objects, including coins. Otherwise, a battery may short circuit, discharge energy, become hot, or leak.
Do not disassemble, install backward, or expose batteries to liquid, moisture, fire, or extreme temperature.
â– Replace all batteries of a set at the same time. Do not mix new batteries with used ones. Do not mix rechargeable and non-rechargeable batteries. Do not mix lithium,
Ni-MH, and Ni-Cd batteries together. Do not mix batteries of different chemistry types, grades, or brands. Failure to observe this precaution may cause leakage.
â– Remove batteries when the product is stored for an extended period of time. In the unlikely event that battery fluid leaks inside the product, contact your local Kodak
Customer Service representative.
â– In the unlikely event that battery fluid leaks onto your skin, wash immediately with water and contact your local health provider. For additional health-related information, contact your local Kodak Customer Service representative.
Dispose of batteries according to local and national regulations.
â–
â– Do not charge non-rechargeable batteries.
For more information on batteries, see www.kodak.com/global/en/service/batteries/batteryUsage.jhtml
54
www.kodak.com/go/support
Battery information
Battery life for Kodak C-series digital cameras
Use the following batteries. Actual battery life may vary based on usage.
CRV3 lithium battery 550
–
700
AA (2) lithium batteries
KAA2HR Ni-MH rechargeable battery (per charge)
Ni-MH AA (2) rechargeable batteries (per charge) oxy-alkaline AA (2) non-rechargeable batteries
125
200
–
225
300
–
300
–
400
500
–
600
0
Battery Life (Approx. number of pictures in Auto mode)
700
Battery life test method: CIPA
Memory card used in test: Kodak SD 128 MB memory card
Appendix
We do not recommend or support alkaline batteries. For acceptable battery life, and to make sure your camera operates dependably, use the replacement batteries listed above.
Extending battery life
â– Limit the following activities that quickly deplete battery power:
â–
– Reviewing your pictures on the camera screen (see page 7 )
– Using the camera LCD screen as a viewfinder (see
– Excessive use of the flash (see page 22 )
Dirt on the battery contacts can affect battery life. Wipe the contacts with a clean,
www.kodak.com/go/support
55
Appendix
â– dry cloth before loading batteries in the camera.
Battery performance is reduced at temperatures below 41
°
F (5
°
C). When using your camera in cold weather, carry spare batteries and keep them warm. Do not discard cold batteries that do not work; when they return to room temperature, they may be usable.
Visit www.kodak.com/go/c310accessories or www.kodak.com/go/cd40accessories for:
Kodak EasyShare camera dock—powers your camera, transfers pictures to your computer, and charges the available Kodak Ni-MH rechargeable digital camera battery KAA2HR.
Kodak EasyShare printer dock—powers your camera, makes
4 x 6 in. (10 x 15 cm) prints with or without a computer, transfers pictures, and charges the available Kodak Ni-MH rechargeable digital camera battery KAA2HR.
Upgrading your software and firmware
Download the latest versions of the software included on the Kodak EasyShare software CD and the camera firmware (the software that runs on the camera). Visit www.kodak.com/go/c310downloads or www.kodak.com/go/cd40downloads.
Additional care and maintenance
â–
â–
â–
If the camera has been subjected to inclement weather or you suspect water has gotten inside the camera, turn off the camera and remove the batteries and card.
Allow all components to air-dry for at least 24 hours before using the camera again.
Blow gently on the lens or camera screen to remove dust and dirt. Wipe gently with a soft, lint-free cloth or an untreated lens-cleaning tissue. Do not use cleaning solutions unless designed specifically for camera lenses. Do not allow chemicals, such as suntan lotion, to contact painted surfaces.
Service agreements are available in some countries. Contact a dealer of Kodak products for more information.
56
www.kodak.com/go/support
Appendix
â– For digital camera disposal or recycling information, contact your local authorities.
In the US, visit the Electronics Industry Alliance Web site at www.eiae.org
or the
Kodak Web site at www.kodak.com/go/c310support or www.kodak.com/go/cd40support
Warranty
Limited warranty
Kodak warrants Kodak EasyShare digital cameras and accessories (excluding batteries) to be free from malfunctions and defects in both materials and workmanship for one year from the date of purchase.
Retain the original dated sales receipt. Proof of the date of purchase will be required with any request for warranty repair.
Limited warranty coverage
This limited warranty will be honored only in the geographical location
that Kodak digital cameras and accessories were purchased.
Kodak will REPAIR or REPLACE Kodak EasyShare digital cameras and accessories if they fail to function properly during the warranty period, subject to any conditions and/or limitations stated herein. Such repair service will include all labor as well as any necessary adjustments and/or replacement parts. Such repair or replacement is the sole remedy under this warranty.
If replacement parts are used in making repairs, these parts may be remanufactured, or may contain remanufactured materials. If it is necessary to replace the entire product, it may be replaced with a remanufactured product.
Limitations
Request for Warranty service will not be accepted without proof of date of purchase, such as a copy of the original dated Kodak EasyShare digital camera or accessory sales receipt. (Always keep the original for your records.)
This warranty does not apply to the battery(s) used in digital cameras or accessories.
www.kodak.com/go/support
57
Appendix
This warranty does not cover circumstances beyond Kodak’s control, nor problems caused by failure to follow the operating instructions in the Kodak EasyShare digital cameras and accessories User’s Guides.
This warranty does not apply when failure is due to shipping damage, accident, alteration, modification, unauthorized service, misuse, abuse, use with incompatible accessories or attachments, failure to follow Kodak’s operation, maintenance or repacking instructions, failure to use items supplied by Kodak (such as adapters and cables), or claims made after the duration of this warranty.
Kodak makes no other express or implied warranty for this product. In the event that the exclusion of any implied warranty is ineffective under the law, the duration of the implied warranty will be one year from the purchase date.
The option of replacement is Kodak’s only obligation. Kodak will not be responsible for any special, consequential or incidental damages resulting from the sale, purchase, or use of this product, regardless of the cause. Liability for any special, consequential or incidental damages (including but not limited to loss of revenue or profit, downtime costs, loss of the use of the equipment, cost of substitute equipment, facilities or services, or claims of your customers for such damages resulting from the purchase, use or failure of the product), regardless of cause or for breach of any written or implied warranty is expressly disclaimed and excluded here from.
Your rights
Some states or jurisdictions do not allow exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Some states or jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific rights, and you may have other rights which vary from state to state or by jurisdiction.
Outside the United States and Canada
In countries other than the United States and Canada, the terms and conditions of this warranty may be different. Unless specific Kodak warranty is communicated to the
58
www.kodak.com/go/support
Appendix
purchaser in writing by a Kodak company, no warranty or liability exists beyond any minimum requirements imposed by law, even though defect, damage, or loss may be by negligence or other act.
Regulatory compliance
FCC compliance and advisory
Kodak EasyShare C310/CD40 digital camera
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for additional suggestions.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulation.
www.kodak.com/go/support
59
Appendix
Canadian DOC statement
DOC Class B Compliance—This Class B digital apparatus complies with Canadian
ICES-003.
Observation des normes-Class B—Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Waste Electrical and Electronic Equipment labeling
In the European Union, do not discard this product as unsorted municipal waste.
Contact your local authorities or go to www.kodak.com/go/recycle for recycling program information.
Korean Class B ITE
VCCI Class B ITE
English translation:
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Install and use the equipment according to the instruction manual.
Australian C-Tick
N137
60
www.kodak.com/go/support
Index
A
camera dock, 56 printer dock, 14, 56
albums, tagging pictures for, 28, 29
alkaline batteries, warning, 1
Australian C-Tick regulatory information, 60
auto
B
batteries
expected life, 55 extending life, 55
battery
button
www.kodak.com/go/support
1
C
cable
reviewing pictures, 7 reviewing videos, 7
turning Liveview default on/off, 26
computer
copy pictures
card to memory, 20 memory to card, 20
CRV3 battery
61
Index
customizing camera settings, 25
D
date
imprinting on pictures, 26 setting, 26
deleting
from internal memory, 11 from SD/MMC card, 11
protecting pictures, videos, 10
dock
E
external video device
62
F
favorites
firmware
Format, 27 formatting internal memory/card, 27
G
H
help
EasyShare software, 46 support, 46 web links, 46
I
Image Storage, 24 setting storage location, 24
information
installing
www.kodak.com/go/support
internal memory
setting image storage location, 24
K
Kodak digital camera batteries, 1
Kodak EasyShare software
L
LCD (liquid crystal display), ii
light
Liveview, 26 turning default on/off, 26
loading
M
Macintosh OS, installing software on, 12
www.kodak.com/go/support
Index
memory
internal, 24 removable card, 24 setting image storage location, 24
Menu
MMC card
setting image storage location, 24
videos
N
O
P
PictBridge enabled printer, 14
pictures
63
Index
power
printing
from a card, 16 from computer, 16
with EasyShare printer dock, 14
protecting pictures, videos, 10
Q
quickview
R
regulatory information, 59, 60
reviewing pictures
64
reviewing videos
slide show, 19 running slide show, 19
S
safety
SD/MMC card
setting image storage location, 24
self timer
service and support, telephone numbers, 46
setting
www.kodak.com/go/support
shutter
Slide Show
slide show
software
status
T
tagging
www.kodak.com/go/support
tagging pictures
tips
troubleshooting
camera/computer communications, 40
U
upgrading software, firmware, 56
USB (universal serial bus)
USB cable
V
Index
65
Index
videos
viewing
viewing picture
W
WEEE
Waste Electrical and Electronic
Windows OS-based computers
66
www.kodak.com/go/support
advertisement
Related manuals
advertisement
Table of contents
- 1 Title page
- 3 Product features
- 5 Table of contents
- 7 Setting up your camera
- 7 Attaching the wrist strap
- 7 Loading the batteries
- 8 Turning on the camera
- 8 Setting the date/time, first time
- 9 Setting the language and date/time, other times
- 9 Storing pictures on an SD or MMC card
- 10 Taking pictures and videos
- 10 Taking a picture
- 10 Taking a video
- 11 Reviewing the picture or video just taken
- 11 Using the camera LCD screen as a viewfinder
- 12 Picture/video capture screens
- 12 Using digital zoom
- 13 Using the flash
- 13 Reviewing pictures and videos
- 14 What the review icons mean
- 15 Magnifying a picture during review
- 15 Viewing multi-up (thumbnails) during review
- 16 Protecting pictures and videos from deletion
- 17 Deleting pictures and videos
- 18 Transferring and printing pictures
- 18 Installing the software
- 19 Transferring pictures with the USB cable
- 19 Also available for transferring
- 20 Printing pictures
- 20 Printing with a Kodak EasyShare printer dock
- 20 Direct printing with a PictBridge enabled printer
- 20 Connecting the camera to a PictBridge enabled printer
- 21 Printing from a PictBridge enabled printer
- 22 Disconnecting the camera from a PictBridge enabled printer
- 22 Using a printer that is not PictBridge enabled
- 22 Ordering prints online
- 22 Printing from an optional SD or MMC card
- 23 Dock compatibility for your camera
- 24 Doing more with your camera
- 24 Putting yourself in the picture or video
- 25 Running a slide show
- 25 Starting the slide show
- 25 Changing the slide show display interval
- 26 Running a continuous slide show loop
- 26 Displaying pictures and videos on a television
- 26 Copying pictures and videos
- 28 Choosing a flash setting
- 29 Changing picture-taking settings
- 31 Customizing your camera
- 34 Viewing picture/video information
- 34 Changing optional review settings
- 34 Pre-tagging for album names
- 34 First-on your computer
- 35 Second-on your camera
- 35 Third-transfer to your computer
- 35 Tagging pictures/videos for albums
- 35 First-on your computer
- 35 Second-on your camera
- 36 Third-transfer to your computer
- 37 Sharing your pictures
- 37 Tagging pictures for printing
- 38 Printing tagged pictures
- 38 Tagging pictures and videos for emailing
- 38 First-on your computer
- 38 Second-tag pictures/videos on your camera
- 39 Third-transfer and email
- 39 Tagging pictures as favorites
- 40 Optional settings
- 41 Removing all favorites from your camera
- 41 Preventing favorites from transferring to the camera
- 41 Printing and emailing favorites
- 42 Troubleshooting
- 42 Camera problems
- 46 Camera/computer communications
- 47 LCD screen messages
- 50 Camera ready light status
- 52 Getting help
- 52 Helpful Web links
- 52 Software help
- 52 Telephone customer support
- 53 Before you call
- 55 Appendix
- 55 Camera specifications
- 58 Storage capacities
- 58 Picture storage capacity
- 58 Video storage capacity
- 59 Power-saving features
- 59 Important safety instructions
- 59 Using this product
- 60 Battery safety and handling
- 61 Battery information
- 61 Battery life for Kodak C-series digital cameras
- 61 Extending battery life
- 62 Upgrading your software and firmware
- 62 Additional care and maintenance
- 63 Warranty
- 63 Limited warranty
- 63 Limited warranty coverage
- 63 Limitations
- 64 Your rights
- 64 Outside the United States and Canada
- 65 Regulatory compliance
- 65 FCC compliance and advisory
- 66 Canadian DOC statement
- 66 Waste Electrical and Electronic Equipment labeling
- 66 Korean Class B ITE
- 66 VCCI Class B ITE
- 66 Australian C-Tick
- 67 Index