InFocus IN102 DLP User Guide

InFocus IN102 DLP User Guide

100

Reference Guide

Regulatory models T102, T104

Table of contents

2

Introduction.................. 3

Projector features........................... 3

Shipping contents .......................... 4

Projector exterior view ................... 5

Controls and functions ................... 6

Positioning your projector ....................... 9

Choosing a location ....................... 9

Obtaining a preferred projected image size.................................... 10

Connection................. 13

Connecting a computer or monitor ......................................... 14

Connecting video source devices......................................... 16

Operation.................... 20

Starting up the projector............... 20

Using the menus .......................... 21

Utilizing the password function .... 22

Switching input signal .................. 24

Adjusting the projected image...... 25

Magnifying and searching for details........................................... 27

Selecting the aspect ratio............. 27

Optimizing the image ................... 29

Setting the presentation timer ...... 33

Hiding the image .......................... 34

Locking control keys .................... 34

Freezing the image ...................... 35

Operating in a high altitude environment ................................. 35

Adjusting the sound ..................... 35

Personalizing the projector menu display.......................................... 36

Shutting down the projector ......... 36

Menu operation............................ 37

Maintenance ...............44

Care of the projector .................... 44

Lamp information ......................... 45

Troubleshooting ........51

Specifications ............52

Projector specifications................ 52

Dimensions .................................. 53

Timing chart ................................. 53

Copyright information .................55

Introduction

Projector features

The projector integrates high-performance optical engine projection and a userfriendly design to deliver high reliability and ease of use.

The projector offers the following features.

Wall color correction allowing projection on surfaces of several predefined colors

Quick auto search speeding up the signal detecting process

Selectable password protected function

Up to 11 sets of picture modes providing multiple choices for different projection purposes

3D color management allowing color adjustments to your liking

Selectable quick cooling function makes the projector cool in a shorter time

Presentation timer for better control of time during presentations

One-key auto-adjustment to display the best picture quality

Digital keystone correction to correct distorted images

Adjustable color balance control for data/video display

High brightness projection lamp

Ability to display 16.7 million colors

Multi-language On-Screen Display (OSD) menus

Switchable normal and economic modes to reduce the power consumption

Component HDTV compatibility (YP b

P r

)

High quality manual zoom lens

The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturer's specifications. This is normal and expected behavior.

Downloaded from ProjectorsManual.com Manuals

Introduction 3

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

4

Projector Power Cord VGA Cable

Reference

Guide CD

Registration

Card

Quick Start Guide

Warranty

Booklet

Safety

Booklet

Pull the tab before using the remote control.

Remote Control & Battery Carry case

Optional accessories

1.

2.

3.

4.

5.

6.

7.

Ceiling mount, wall mount

LiteShow II wireless presentation adaptor

Pull down and pull up 4:3 screens

Cables and adaptors

Replacement lamp

Optional remote

Projector lock system

Projector exterior view

Front/upper side

1

1.

2.

3.

4.

5.

6.

7.

External control panel

(See

"Projector and remote control" on page 6

for details.)

Vent (heated air exhaust)

Quick-release button

Lens cover

Focus ring and Zoom ring

Front IR remote sensor

Projection lens

2

3

5

6

7

4

Rear/lower side

8 9

10 11 12 13 14 15

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

AC power cord inlet

RS-232 control port

RGB signal output socket

RGB (PC)/Component video

(YPbPr/YCbCr) signal input socket

Video input socket

S-Video input socket

Audio signal input socket

Audio signal output socket

Kensington anti-theft lock slot

Quick-release foot

Lamp cover

Rear adjuster foot

16 17 18

Warning

THIS APPARATUS MUST BE GROUNDED.

When installing the unit, make certain that the associated wall switch or AC power outlet is easily accessible, so that the unit can be quickly disconnected if needed.

Downloaded from ProjectorsManual.com Manuals

Introduction 5

6

6

7

8

1

2

3

4

5

Controls and functions

Projector and remote control

9

10

11

12

13

11

5

14

15

16

17

1.

2.

3.

4.

Focus ring

Adjusts the focus of the projected image. See

"Fine-tuning the image size and clarity" on page 26 for details.

Zoom ring

5.

Adjusts the size of the image. See

"Fine-tuning the image size and clarity" on page 26 for details.

TEMPerature indicator light

6.

Lights up red if the projector's temperature becomes too high. See

"Indicators" on page 50 for details.

POWER indicator light

7.

Lights up or flashes when the projector

is under operation. See "Indicators" on page 50

for details.

POWER

Toggles the projector between standby mode and on. See

"Starting up the projector" on page 20

and

"Shutting down the projector" on page

36 for details.

Left/BLANK

Used to hide the screen picture. See

"Hiding the image" on page 34 for

details.

MODE/ENTER

Selects an available picture setup

mode. See "Selecting a picture mode" on page 29 for details.

Enacts the selected On-Screen

Display (OSD) menu item.

12

13

7

11

8

11

10

8.

9.

10.

11.

12.

MENU/EXIT

Turns on the On-Screen Display

(OSD) menu. Goes back to previous

OSD menu, exits and saves menu

settings. See "Using the menus" on page 21

for details.

LAMP indicator light

13.

14.

Indicates the status of the lamp. Lights up or flashes when the lamp has

developed a problem. See "Indicators"

15.

on page 50

for details.

AUTO

Automatically determines the best picture timings for the displayed

image. See "Auto-adjusting the image" on page 25

for details.

Keystone/Arrow keys (

/ Down)

/ Up,

Manually corrects distorted images resulting from an angled projection.

See "Correcting keystone" on page 26

for details.

16.

17.

Right

/

Activates panel key lock. See "Locking control keys" on page 34

for details.

When the On-Screen Display (OSD)

menu is activated, the #6, #11, and

#12 keys are used as directional

arrows to select the desired menu items and to make adjustments. See

"Using the menus" on page 21

for details.

SOURCE

Displays the source selection bar.

See

"Switching input signal" on page

24 for details.

Freeze

Freezes the projected image. See

"Freezing the image" on page 35

for details.

Left

Selects the desired menu items and makes adjustments. See

"Using the menus" on page 21 for details.

BLANK

Used to hide the screen picture. See

"Hiding the image" on page 34 for

details.

Digital Zoom keys (+, -)

Magnifies or reduces the projected

picture size. See "Magnifying and searching for details" on page 27 for

details.

Downloaded from ProjectorsManual.com Manuals

Introduction 7

8

Remote control effective range

Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam.

Approx

. 15°

Replacing the remote control battery

1.

Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2.

3.

Insert the new battery (Type: CR-2025) in the holder. Note the positive polarity should face outward.

Push the holder into the remote control.

CAUTION

• Avoid excessive heat and humidity.

There may be battery damage if the battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the battery manufacturer.

Dispose of the used battery according to the battery manufacturer’s instructions.

Never throw a battery into a fire. There may be danger of an explosion.

If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Your projector is designed to be installed in one of four possible installation locations:

1.

Front Table

Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

2.

Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Purchase the InFocus ceiling mount, SP-CEIL-

UNIV, from your dealer to mount your projector on the ceiling.

Set

Front Ceiling

in the

SYSTEM SETUP: Basic

>

Projector Position

menu after you turn the projector on.

3.

Rear Table

Select this location with the projector placed near the floor behind the screen.

Note that a special rear projection screen is required.

Set

Rear Table

in the

SYSTEM SETUP: Basic

>

Projector Position

menu after you turn the projector on.

4.

Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the

InFocus ceiling mount, SP-CEIL-UNIV, are required for this installation location.

Set

Rear Ceiling

in the

SYSTEM SETUP: Basic

>

Projector Position

menu after you turn the projector on.

Downloaded from ProjectorsManual.com Manuals

Positioning your projector 9

10

Obtaining a preferred projected image size

The distance from the projector lens to the screen, the zoom setting, and the video format all factor into the resulting projected image size.

4:3 is the native aspect ratio of this projector. To be able to project a complete 16:9

(widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the projector's native aspect width. This will result in a proportionally smaller height equivalent to 75% of the projector's native aspect height.

4:3 aspect image in a 4:3 aspect display area

16:9 aspect image scaled to a 4:3 aspect display area

Thus, a 16:9 aspect image will not utilize 25% of the height of a 4:3 aspect image displayed by this projector. This will be seen as darkened (unlit) bars along the top and bottom (vertical 12.5% height respectively) of the 4:3 projection display area whenever displaying a scaled 16:9 aspect image in the vertical center of the 4:3 projection display area.

The projector should always be placed horizontally level (like flat on a table), and positioned directly perpendicular (90° right-angle square) to the horizontal center of the screen. This prevents image distortion caused by angled projections (or projecting onto angled surfaces).

The modern digital projector does not project directly forward (like older style reelto-reel film projectors did). Instead, digital projectors are designed to project at a slightly upward angle above the horizontal plane of the projector. This is so that they can be readily placed on a table and will project forward and upwards onto a screen positioned so that the bottom edge of the screen is above the level of the table (and everyone in the room can see the screen).

If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects at a slightly downward angle.

You can see from the diagram on page

12 , that this type of projection causes the

bottom edge of the projected image to be vertically offset from the horizontal plane of the projector. When ceiling mounted, this refers to the top edge of the projected image.

If the projector is positioned further away from the screen, the projected image size increases, and the vertical offset also increases proportionately.

When determining the position of the screen and projector, you will need to account for both the projected image size and the vertical offset dimension, which are directly proportional to the projection distance.

InFocus has provided a table of 4:3-aspect-ratio screen sizes to assist you in determining the ideal location for your projector. There are two dimensions to consider, the perpendicular horizontal distance from the center of the screen

(projection distance), and the vertical offset height of the projector from the horizontal edge of the screen (offset).

How to determine the position of the projector for a given screen size

1.

2.

3.

Select your screen size.

Refer to the table and find the closest match to your screen size in the left columns labelled

"4:3 screen diagonal"

. Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labelled

"Average" . This is the projection distance.

On that same row, look across to the right column and make note of the

"Vertical offset" value. This will determine the final vertical offset placement of

the projector in relation to the edge of the screen.

4.

The recommended position for the projector is aligned perpendicular to the horizontal center of the screen, at the distance from the screen determined in

step 2 above, and offset by the value determined in step 3 above.

For example, if you are using a 108-inch screen, the average projection distance is

4320 mm (170”) and with a vertical offset of 82 mm (3.2”).

If you place the projector in a different position (to that recommended), you will have to tilt it down or up to center the image on the screen. In these situations, some image distortion will occur. Use the Keystone function to correct the distortion. See

"Correcting keystone" on page 26 for details.

How to determine the recommended screen size for a given distance

This method can be used for situations where you have purchased this projector and would like to know what screen size will fit in your room.

The maximum screen size is limited by the physical space available in your room.

1.

2.

Measure the distance between the projector and where you want to position the screen. This is the projection distance.

Refer to the table and find the closest match to your measurement in the

average distance from screen column labelled "Average" . If the min and max

values are available on the table, check that your measured distance is between the min and max distances listed on either side of the average distance value.

3.

4.

Using this value, look across that row to the left to find the corresponding screen diagonal listed in that row. That is the projected image size of the projector at that projection distance.

On that same row, look across to the right column and make note of the

"Vertical offset" value. This will determine the final placement of the screen in

relation to the horizontal plane of the projector.

For example, if your measured projection distance was 4.5 m (177”), the closest match in the

"Average"

column is 4320 mm (170”). Looking across this row shows that a 108-inch screen is required.

Downloaded from ProjectorsManual.com Manuals

Positioning your projector 11

12

Projection dimensions

Refer to

"Dimensions" on page 53 for the center of lens dimensions of this projector

before calculating the appropriate position.

Maximum zoom

Minimum zoom

Screen

Center of lens

Vertical offset

Projection distance

4:3 screen diagonal

Feet

4

5

6

7

8

9

10

12

15

18

25

Inches

48

59

60

72 mm

1219

1500

1524

1829

79 2000

84

96

108

120

144

2134

2438

98 2500

2743

118 3000

3048

138 3500

3658

157 4000

180 4572

197 5000

216 5486

2250

2286

2743

3000

3200

3657

3750

4114

Recommended projection distance from screen

Min length

(with max.

Average Max length

(with min.

mm

zoom)

Inches

1829 72 mm

1920

Inches

76 mm

2011

zoom)

Inches

79

4499

4571

5249

5486

5999

6857

7499

8229

236 6000

300

8999

7620 11429

89

90

108

118

126

144

148

162

177

180

207

216

236

270

295

324

354

450

2362

2400

2880

3150

3360

3840

3937

4320

4724

4800

5512

5760

6299

7200

7874

8640

9449

12000

93

94

113

124

132

151

155

170

186

189

217

227

248

283

310

340

372

472

2475

2514

3017

3300

3520

4023

4124

4526

4949

5029

5774

6034

6599

7543

8249

9051

9899

12571

97

99

119

130

139

158

162

178

195

198

227

238

260

297

325

356

390

495

Vertical offset

There is 3% tolerance among these numbers due to optical component variations. InFocus recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

64

73

75

82

90

91

105

110 mm

37

45

46

55

60

120

137

150

165

180

229

4.7

5.4

5.9

6.5

7.1

9.0

2.5

2.9

3.0

3.2

3.5

3.6

4.1

4.3

Inches

1.4

1.8

1.8

2.2

2.4

Connection

When connecting a signal source to the projector, be sure to:

1.

2.

3.

Turn all equipment off before making any connections.

Use the correct signal cables for each source.

Ensure the cables are firmly inserted.

In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 4

). Additional cables can be purchased from InFocus.com in select areas, your dealer and/or from a commercial electronics store.

Downloaded from ProjectorsManual.com Manuals

Connection 13

Connecting a computer or monitor

Connecting a computer

The projector provides a VGA input socket that allows you to connect it to both

IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.

To connect the projector to a notebook or desktop computer:

1.

2.

3.

4.

Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

Connect the other end of the VGA cable to the

COMPUTER IN1

/

COMPUTER

IN2

signal input socket on the projector.

If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the

AUDIO IN

socket of the projector.

If you wish, you can use another suitable audio cable and connect one end of the cable to the

AUDIO OUT

jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen

Display (OSD) menus. See "Adjusting the sound" on page 35 for details.

The built-in speaker will be muted when the

AUDIO OUT

jack is connected.

The final connection path should be like that shown in the following diagram:

Notebook or desktop computer

Speakers

14

VGA cable

Audio cable

Audio cable

Many notebooks do not turn on their external video ports when connected to a projector.

Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press

FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the

MONITOR OUT

signal output socket on the projector to an external monitor with a VGA cable following the instructions below:

To connect the projector to a monitor:

1.

2.

3.

Connect the projector to a computer as described in

"Connecting a computer" on page 14

.

Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.

Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.

Connect the other end of the cable to the

MONITOR OUT

socket on the projector.

The final connection path should be like that shown in the following diagram:

Monitor

(VGA) or (DVI-A)

(VGA)

• The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER IN1 jack.

• If you wish to use this connection method when the projector is in standby mode, make sure the VGA Out function is turned on in the SYSTEM SETUP: Advanced menu. See

"VGA

Out" on page 43

for details.

Downloaded from ProjectorsManual.com Manuals

Connection 15

16

Connecting video source devices

You can connect your projector to various video source devices that provide any one of the following output sockets:

• Component video

S-Video

• Video (composite)

You only need to connect the projector to a single video source device; however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Best video quality

The best available video connection method is Component video (not to be confused with composite video). Digital TV tuner and DVD players output

Component video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video.

See "Connecting a Component video source device" on page 17

for how to connect the projector to a component video device.

Better video quality

The S-Video method provides a better quality analog video than standard composite video. If you have both composite video and S-Video output terminals on your video source device, you should elect to use the S-Video option.

See "Connecting an S-Video source device" on page 18 for how to connect the

projector to an S-Video device.

Good video quality

Composite video is analog video and will result in a perfectly acceptable, but less than optimal result from your projector. The other methods described above provide better video quality.

See

"Connecting a composite video source device" on page 19

for how to connect the projector to a composite video device.

Connecting audio

The projector has one built-in mono speaker which is designed to provide basic audio functionality accompanying data presentations for business purposes only. It is not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker.

If you have a separate sound system, you will most likely want to connect the audio output of your video source device to that sound system, instead of to the mono audio projector. The audio connections are provided for informational purposes only. You need not connect audio to the projector if there is an alternate sound system available, or if audio is not required.

Connecting a Component video source device

Examine your video source device to determine if it has a set of unused

Component video output sockets available:

• If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component video source device:

1.

2.

3.

4.

Take a Component video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component video output sockets of the video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

Connect the other end of the Component video to VGA (D-Sub) adaptor cable

(with a D-Sub type connector) to the

COMPUTER IN1

/

COMPUTER IN2

socket on the projector.

If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the

AUDIO IN

socket of the projector.

If you wish, you can use another suitable audio cable and connect one end of the cable to the

AUDIO OUT

jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen

Display (OSD) menus. See "Adjusting the sound" on page 35 for details.

The built-in speaker will be muted when the

AUDIO OUT

jack is connected.

The final connection path should be like that shown in the following diagram:

AV device

Speakers

RS-232

MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN AUDIO OUT

Component video to VGA (D-Sub) adaptor cable

Audio cable Audio cable

The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 16 for details.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Downloaded from ProjectorsManual.com Manuals

Connection 17

Connecting an S-Video source device

Examine your video source device to determine if it has an unused S-Video output socket available:

• If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.

2.

3.

4.

Take an S-Video cable and connect one end to the S-Video output socket of the video source device.

Connect the other end of the S-Video cable to the

S-VIDEO

socket on the projector.

If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the

AUDIO IN

socket of the projector.

If you wish, you can use another suitable audio cable and connect one end of the cable to the

AUDIO OUT

jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen

Display (OSD) menus. See "Adjusting the sound" on page 35 for details.

The built-in speaker will be muted when the

AUDIO OUT

jack is connected.

The final connection path should be like that shown in the following diagram:

AV device

18

RS-232 MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN AUDIO OUT

S-Video cable

Audio cable

Audio cable

The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 16 for details.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

If you have already made a Component video connection between the projector and this S-

Video source device using Component video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See

"Connecting video source devices" on page 16

for details.

Connecting a composite video source device

Examine your video source device to determine if it has a set of unused composite video output sockets available:

• If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a composite video source device:

1.

2.

3.

4.

Take a video cable and connect one end to the composite video output socket of the video source device.

Connect the other end of the video cable to the

VIDEO

socket on the projector.

If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the

AUDIO IN

socket of the projector.

If you wish, you can use another suitable audio cable and connect one end of the cable to the

AUDIO OUT

jack of the projector, and the other end to your external speakers (not supplied).

Once connected, the audio can be controlled by the projector On-Screen

Display (OSD) menus. See "Adjusting the sound" on page 35 for details.

The built-in speaker will be muted when the

AUDIO OUT

jack is connected.

The final connection path should be like that shown in the following diagram:

AV device

RS-232 MONITOR OUT COMPUTER IN1 COMPUTER IN2 VIDEO S -VIDEO AUDIO IN AUDIO OUT

Video cable

Audio cable

Audio cable

The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 16 for details.

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

You need only connect to this device using a composite video connection if Component video and S-Video inputs are unavailable for use. See

"Connecting video source devices" on page 16

for details.

Downloaded from ProjectorsManual.com Manuals

Connection 19

Operation

Starting up the projector

1.

Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch, if applicable. Check that the

POWER indicator light

on the projector lights orange after power has been applied.

2.

Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp.

20

3.

4.

5.

6.

Press

POWER

on the projector or remote control to start the projector. The

POWER indicator light

flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

If you are prompted for a password, press the arrow keys to enter a six-digit

password. See "Utilizing the password function" on page 22

for details.

Switch all of the connected equipment on.

The projector will start to search for input signals. The current input signal being scanned displays in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message '

No Signal

' will continue displaying until an input signal is found.

You can also press

SOURCE

on the projector or remote control to select your desired input signal. See

"Switching input signal" on page 24 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting.

See "Timing chart" on page 53

for details.

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Highlight

Sub-menu

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

16

0

Off

Auto

ENTER

Status

Current input signal

Analog RGB

On

Disable

MENU Exit

Press

MENU/

EXIT

to the previous page or to exit.

To use the OSD menus, please set them to your preferred language first.

1.

Press

MENU/EXIT

on the projector or remote control to turn the OSD menu on.

3.

Press highlight

Language

and press to select a preferred language

.

/

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

DISPLAY

16

0

Off

Auto

On

Disable

SYSTEM SETUP: Basic

Presentation Timer

Language

Projector Position

Auto Power Off

Blank Timer

Panel Key Lock

Timer Controller

Splash Screen

English

Front Table

Disable

Disable

Off

Disable

InFocus

Analog RGB MENU Exit

Analog RGB

MENU Exit

2.

Use / to highlight the

SYSTEM

SETUP: Basic

menu.

SYSTEM SETUP: Basic

Presentation Timer

Language

Projector Position

Auto Power Off

Blank Timer

Panel Key Lock

Timer Controller

Splash Screen

English

Front Table

Disable

Disable

Off

Disable

InFocus

4.

Press

MENU/EXIT

twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB MENU Exit

Operation 21

Downloaded from ProjectorsManual.com Manuals

22

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the

On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to

"Using the menus" on page 21 .

You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print this reference guide (if necessary) and write the password you used in this guide, and keep it in a safe place for later use.

Setting a password

Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started.

1.

2.

3.

4.

Open the OSD menu and go to the

SYSTEM SETUP: Advanced

>

Security

Settings

menu. Press

MODE/ENTER

. The

Security Settings

page displays.

(

Highlight

Power on lock

and select

On

by pressing

As pictured to the right, the four arrow keys

/ .

INPUT NEW PASSWORD

, , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the

Security Settings

page.

MENU Back

The digits being input will display as asterisks onscreen. Write your selected password down here in this reference guide in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this reference guide in a safe place.

5.

To leave the OSD menu, press

MENU/EXIT.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for three seconds, and the message

'INPUT PASSWORD'

follows. You can retry by entering another six-digit

Password Error

Please try again.

password, or if you did not record the password in this reference guide, and you absolutely do not remember it, you can use the password recall procedure. See

"Entering the password recall procedure" on page 23 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1.

2.

3.

Press and hold

AUTO

on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

Write down the number and turn off your projector.

Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact InFocus

Customer Center.

Recall code:

0 2 1 2

MENU Exit

Changing the password

1.

2.

3.

Open the OSD menu and go to the

SYSTEM SETUP: Advanced

>

Security

Settings

>

Change password

menu.

Press

MODE/ENTER

. The message

'INPUT CURRENT PASSWORD'

displays.

Enter the old password.

4.

If the password is correct, another message

'INPUT NEW PASSWORD'

displays.

If the password is incorrect, the password error message displays lasting for three seconds, and the message

'INPUT CURRENT PASSWORD'

displays for your retry. You can press

MENU/EXIT

to cancel the change or try another password.

Enter a new password.

The digits being input will display as asterisks on-screen. Write your selected password down here in this reference guide in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this reference guide in a safe place.

5.

6.

7.

Confirm the new password by re-entering the new password.

You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

To leave the OSD menu, press

MENU/EXIT.

Disabling the password function

To disable password protection, go back to the

SYSTEM SETUP: Advanced

>

Security Settings > Power on lock

menu after opening the OSD menu system.

Select

Off

by pressing the current password.

/

.

The message

'INPUT PASSWORD'

displays. Enter

If the password is correct, the OSD menu returns to the

Security

Settings

page with

'Off'

shown in the row of

Power on lock

. You will not have to enter the password next time you turn on the projector.

If the password is incorrect, the password error message displays lasting for three seconds, and the message

'INPUT PASSWORD'

displays for

Operation 23

Downloaded from ProjectorsManual.com Manuals

24

your retry. You can press

MENU/EXIT

to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password on hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.

Be sure the

Quick Auto Search

function in the

SOURCE

menu is

On

(which is the default of this projector) if you want the projector to automatically search for the signals.

You can also manually cycle through the available input signals.

1.

2.

Press

SOURCE

on the projector or remote control. A source selection bar displays.

Press / until your desired signal is selected and press

MODE/ENTER

.

Once detected, the selected source information will display on the screen for seconds. If there is multiple equipment

connected to the projector, repeat steps 1-

2 to search for another signal.

e m a N l e a d

G o e r A

M

O

0 . 5 4

The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "video" using mostly moving images (movies).

The input signal type affects the options available for the Preset Mode. See

"Selecting a picture mode" on page 29

for details.

The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution.

Any other resolutions will be scaled by the projector depending upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture clarity. See

"Selecting the aspect ratio" on page 27 for details.

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.

Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in

2.

position.

Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

2

1

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see

"Correcting keystone" on page 26 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press

AUTO

on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

The screen will be blank while AUTO is functioning.

This function is only available when PC signal (analog RGB) is selected.

Downloaded from ProjectorsManual.com Manuals

Operation 25

26

Fine-tuning the image size and clarity

1.

Adjust the projected image to the size that you need using the zoom ring.

2.

Then sharpen the image by rotating the focus ring.

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

Besides adjusting the height of the projector, you may need to follow one of these steps:

• Using the remote control

Press / on the projector control panel or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

1.

2.

3.

Using the OSD menu

Press

MENU/EXIT

and then press / until the

DISPLAY

menu is highlighted.

highlight and press

MODE/ENTER

. The

Keystone

correction page displays.

Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image.

Press

/ .

Press

/ .

Magnifying and searching for details

If you need to look at specific details on the projected picture, magnify the picture.

Use the direction arrow keys for navigating the picture.

1.

2.

3.

4.

Using the remote control

Press

Digital Zoom +/-

to display the

Zoom bar.

Press

Digital Zoom +

to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

Use the directional arrows ( , , on the projector or remote control to navigate the picture.

, )

To restore the picture to its original size, press

AUTO

. You can also press

Digital Zoom -

. When the key is pressed again, the picture is further reduced until it is restored to the original size.

1.

2.

3.

4.

5.

6.

7.

Using the OSD menu

Press

MENU/EXIT

and then press highlighted.

/ until the DISPLAY menu is

Press to highlight

Digital Zoom

and press

MODE/ENTER

. The Zoom bar displays.

Repeat steps 2-4 in the section of "Using the remote control"

above. Or if you are using the projector control panel, continue to the following steps.

Press on the projector repeatedly to magnify the picture to a desired size.

To navigate the picture, press

MODE/ENTER

to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture.

Use the directional arrows ( to navigate the picture.

, , , ) on the projector or remote control

To reduce size of the picture, press

MODE/ENTER

to switch back to the zoom in/out functionality, and press

AUTO

to restore the picture to its original size.

You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog

TV and computers are in 4:3 ratio, which is the default for this projector, and digital

TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected image ratio (no matter what aspect the source is):

1.

2.

Press

MENU/EXIT

and then press highlighted.

Press to highlight

Aspect Ratio

.

/ until the

DISPLAY

menu is

Operation 27

Downloaded from ProjectorsManual.com Manuals

28

3.

About the aspect ratio

In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas.

1.

Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

Auto

: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio.

16:10 picture

2.

3.

4.

15:9 picture

Real

:

The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.

4:3

: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio.

This is most suitable for 4:3 images like computer monitors, standard definition TV and

4:3 aspect DVD movies, as it displays them without aspect alteration.

16:9

: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition

TV, as it displays them without aspect alteration.

4:3 picture

16:9 picture

4:3 picture

16:9 picture

Optimizing the image

Selecting a picture mode

The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.

To select an operation mode that suits your need, you can follow one of the following steps.

m e a N l e a d

G e r A o

O

M m m 0 . 5 4

Press

MODE/ENTER

on the remote control or projector repeatedly until your desired mode is selected.

Go to the mode.

PICTURE > Preset Mode

menu and press / to select a desired

1.

2.

3.

4.

Setting the User mode

There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the

User

) as a starting point and customize the settings.

5.

6.

Press

MENU/EXIT

to open the On-Screen Display (OSD) menu.

Go to the

PICTURE

>

Preset Mode

menu.

Press /

Press

User

.

to select a sub-menu item to be changed and adjust the value with

/

. See "Fine-tuning the image quality in user modes"

below for details.

When all settings have been done, highlight

Save Settings

and press

MODE/

ENTER

to store the settings.

The confirmation message '

Setting Saved

' displays.

Downloaded from ProjectorsManual.com Manuals

Operation 29

30

Using Wall Color

In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the

Wall Color

feature can help correct the projected picture’s color to prevent possible color difference between the source and projected pictures.

To use this function, go to the

DISPLAY

>

Wall Color

menu and press / to select a color which is the closest to the color of the projection surface. There are several precalibrated colors to choose from:

Light Yellow

,

Pink

,

Light Green

,

Blue

, and

Blackboard

.

Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available when

User

mode is selected. You can make adjustments to these functions based on your needs.

Adjusting Brightness

Highlight

Brightness

in the

PICTURE

menu and adjust the values by pressing on the projector or remote control.

The higher the value, the brighter the image.

Likewise, the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.

+30

+50

Adjusting Contrast

Highlight

Contrast

in the

PICTURE

menu and adjust the values by pressing on the projector or remote control.

/

+70

/

The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the

Brightness

setting to suit your selected input and viewing environment.

+30

0 -30

Adjusting Color

Highlight

Color

in the

PICTURE

menu and adjust the values by pressing the projector or remote control.

/

Adjusting Sharpness

Highlight

Sharpness

in the

PICTURE

menu and adjust the values by pressing

on the projector or remote control.

on

Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic.

Adjusting Tint

Highlight

Tint

in the

PICTURE

menu and adjust the values by pressing the projector or remote control.

/ on

The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes.

/

The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes.

Adjusting Brilliant Color

Highlight

Brilliant Color

in the

PICTURE

menu and select by pressing the projector or remote control.

/ on

This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select

On

. If you don’t need it, select

Off

.

On

is the default and recommended selection for this projector. When

Off

is selected, the

Color Temperature

function is not available.

Selecting a Color Temperature

Highlight

Color Temperature

in the

PICTURE

menu and adjust the values by pressing / on the projector or remote control.

The options available for color temperature* settings vary according to the signal type selected.

1.

2.

3.

4.

T1:

With the highest color temperature, T1 makes the image appear the most bluish white than other settings.

T2:

Makes images appear bluish white.

T3:

T4:

Maintains normal colorings for white.

Makes images appear reddish white.

*About color temperatures:

There are many different shades that are considered to be "white" for various purposes. One of the common methods of representing white color is known as the

“color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it.

Downloaded from ProjectorsManual.com Manuals

Operation 31

32

3D Color Management

In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room.

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered.

3D

Color Management

provides fine color control adjustment to allow for more accurate color reproduction, should you require it.

Proper color management can only be achieved under controlled and reproducible viewing conditions. You will need to use a colorimeter (color light meter), and provide a set of suitable source images to measure color reproduction. These tools are not provided with the projector, however, your projector supplier should be able to provide you with suitable guidance, or even an experienced professional installer.

1.

2.

3.

3D Color Management

provides six sets (RGBCMY) of colors to be adjusted.

When you select each color, you can independently adjust its range and saturation according to your preference.

If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc. You can project any image from the disc on the screen and enter the

3D Color

Management

menu to make adjustments.

To adjust the settings:

4.

5.

6.

7.

8.

Go to the

PICTURE

menu and highlight

3D Color Management

.

Press

MODE/ENTER

and the

3D Color Management

page displays.

Highlight

Primary Color

and press /

Yellow, Green, Cyan, Blue, or Magenta.

to select a color from among Red,

Press

Hue

and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

Press

Saturation

and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately.

RED

Magenta

Yellow

BLUE

Cyan

GREEN

For example, if you select Red and set its value at 0, only the saturation of pure red will be affected.

Press

Gain

and adjust its values to your preference by pressing / . The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

Repeat steps 3 to 6 for other color adjustments.

Make sure you have made all of the desired adjustments.

9.

Press

MENU/EXIT

to exit and save the settings.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

Setting the presentation timer

The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.

2.

Go to the

SYSTEM SETUP: Basic >

Presentation Timer

menu and press

MODE/ENTER

to display the

Presentation

Timer

page.

Highlight

Timer Period

and decide the time

Presentation Timer

Timer Period

Timer Display

Timer Position

Timer Counting Direction

Sound Reminder

15

Always

Top-Left

Count Down

Off

On Off

period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

MENU Back

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.

Press to highlight

Timer Display

and choose if you want the timer to show up on the screen by press ing

/

.

Selection Description

Always Displays the timer on screen throughout the presentation time.

1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).

Never Hides the timer throughout the presentation time.

4.

5.

6.

7.

8.

highlight and set the timer position by pressing

/

.

Top-Left

Press

Bottom-Left Top-Right Bottom-Right

to highlight

Timer Counting Direction

and select your desired counting direction by pressing / .

Selection

Count Up

Count Down

Description

Increases from 0 to the preset time.

Decreases from the preset time to 0.

highlight and decide if you want to activate sound reminder by pressing / . If you select

On

, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

To activate the presentation timer, press and press

MODE/ENTER

.

and press / to highlight

On

A confirmation message displays. Highlight

Yes

and press

MODE/ENTER

to confirm. You will see the message “

Timer is On

” displaying on the screen.

The timer starts counting at the time the timer is on.

Operation 33

Downloaded from ProjectorsManual.com Manuals

34

To cancel the timer, perform the following steps.

1.

2.

Enter the

SYSTEM SETUP: Basic > Presentation Timer

menu and highlight

Off

. Press

MODE/ENTER

. A confirmation message displays.

Highlight

Yes

and press

MODE/ENTER

to confirm. You will see the message

Timer is Off

” displaying on the screen.

Hiding the image

In order to draw the audience's full attention to the presenter, you can use

BLANK

on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image.

The word '

BLANK

' appears at the lower right corner of the screen while the image is hidden.

You can set the blank time in the

SYSTEM

SETUP: Basic > Blank Timer

menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen.

Once BLANK is pressed, the projector enters Economic mode automatically.

CAUTION

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the

Panel Key Lock

is on, no control keys on the projector will operate except

POWER

.

1.

2.

Press

/

on the projector or remote control or go to the

SYSTEM SETUP:

Basic > Panel Key Lock

menu

, and select

On

by pressing / projector or remote control.

on the

A confirmation message displays. Select

Yes

to confirm.

To release panel key lock, press and hold

/ for 3 seconds on the projector or remote control.

e m a N l e a d

G o e r A

O

M

0 . 5 4

You can also use the remote control to enter the

SYSTEM SETUP: Basic

>

Panel

Key Lock

and press / to select

Off

.

Keys on the remote control are still in use when panel key lock is enabled.

If you press POWER to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on.

Freezing the image

Press on the remote control to freeze the image. The word '

FREEZE

' will display in the upper left corner of the screen.

To release the function, press any key on the projector or remote control.

Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen on screen.

Operating in a high altitude environment

We recommend you use the

High Altitude Mode

when your environment is between 1500 m–3000 m (4921'– 9843') above sea level, and temperature is between 0°C–35°C (32°F–95°F).

CAUTION

Do not use the High Altitude Mode if your altitude is between 0 m (0') and 1500 m (4921') and temperature is between 0°C (32°F) and 35°C (95°F). The projector will be over cooled, if you turn the mode on under a such condition.

To activate the

High Altitude Mode

:

1.

Press

MENU/EXIT

and then press

2.

/ until the

SYSTEM SETUP: Advanced

menu is highlighted.

Press

High Altitude Mode

WARNING

We recommend you use the High

Altitude Mode by selecting it whenever your environment is higher than 1500 m.

Do you want to turn the High Altitude

Mode on?

and press / to select

On

. A confirmation message displays.

Yes No

3.

Highlight

Yes

and press

MODE/ENTER

.

Operation under "

High Altitude Mode

" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to

High Altitude Mode

to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker.

Be sure you have made a correct connection to the projector audio input. See

"Connection" on page 13 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.

2.

Press

MENU/EXIT

and then press

Advanced

menu is highlighted.

/ until the

SYSTEM SETUP:

highlight and press

MODE/ENTER

. The

Audio

Settings

page displays.

Operation 35

Downloaded from ProjectorsManual.com Manuals

36

3.

Highlight

Mute

and press / to select

On

.

Adjusting the sound level

To adjust the sound level:

1.

2.

Repeat steps 1-2 above.

highlight and press / to select a desired sound level.

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences.

The following settings do not affect the projection settings, operation, or performance.

Menu display time

in the

SYSTEM SETUP: Advanced

>

Menu Settings

menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments.

Use / to select a suitable time frame.

Menu position

in the

SYSTEM SETUP: Advanced

>

Menu Settings

menu sets the OSD position in five locations. Use / to select a preferred position.

Language

in the

SYSTEM SETUP: Basic

menu sets your familiar language for the OSD menus. Use / to select your language.

Splash Screen

in the

SYSTEM SETUP: Basic

menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen.

Shutting down the projector

1.

Press

POWER

and a confirmation message displays prompting you.

If you don't respond in a few seconds, the message will disappear.

2.

3.

4.

Press

POWER

a second time. The

POWER indicator light

flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately

90 seconds to cool down the projector.

The

POWER indicator light

is a steady orange and fans stop.

Disconnect the power cord from the wall socket if the projector will not be used for an extended period of time.

CAUTION

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick Cooling function. See "Quick

Cooling" on page 42

for details.

Do not unplug the power cord before the projector shutdown sequence is complete or during the 90-second cooling down process.

If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Main menu

4.

SYSTEM

SETUP:

Basic

Sub-menu

Presentation

Timer

Options

1.

DISPLAY

2.

PICTURE

Wall Color

Off

/

Light Yellow

/

Pink

/

Light

Green

/

Blue

/

Blackboard

Auto

/

Real

/

4:3

/

16:9 Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

Preset Mode

Brightness

Contrast

Color

Tint

Sharpness

Brilliant Color

Color Temperature

Primary Color

3D Color

Management

On/Off

Disable

/

Invert

Presentation

/

Video

/

Bright

/

Whiteboard

/

Blackboard/Beige Wall/User

Hue

Saturation

Gain

On

/

Off

T1/T2/T3/T4

R/G/B/Y/C/M

Save Settings

3. SOURCE

Quick Auto Search On

/

Off

Timer Period

Timer Display

Timer Position

1~240 minutes

Always/1 min/2 min/3 min/Never

Bottom-right/Top-right/Bottomleft/Top-left

Timer Counting

Direction

Count Down

Sound Reminder On

/

Off

On

/

Off

/

Count Up

Operation 37

Downloaded from ProjectorsManual.com Manuals

38

Language

4.

SYSTEM

SETUP:

Basic

5.

SYSTEM

SETUP:

Advanced

6.

INFORMATION

Projector Position

Auto Power Off

Blank Timer

Panel Key Lock

Front Table

/

Rear Table

/

Rear

Ceiling

/

Front Ceiling

Disable

/5 min/10 min/15 min/20 min/25 min/30 min

Disable

/5 min/10 min/15 min/20 min/25 min/30 min

On

/

Off

Timer Controller

Splash Screen

Quick Cooling

High Altitude Mode

Mute

Audio Settings

Volume

Menu display time

Menu Settings

Menu position

Disable

/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr

Black/Blue/InFocus

On

On

On

/

/

/

Off

Off

Off

5 sec/10 sec/15 sec/20 sec/25 sec/30 sec

Center/Top-left/Top-right/Bottomright/Bottom-left

Closed Caption

Closed Caption

Enable

Caption Version

On

/

Off

VGA Out

CC1/CC2/CC3/CC4

On

/

Off

Normal

/

Economic

Lamp Settings

Lamp mode

Reset lamp timer

Security

Settings

Equivalent lamp hour

Change password

Power on lock

Reset All Settings

On

/

Off

Current System Status

Source

Preset Mode

Resolution

Color System

Equivalent Lamp Hour

Description of each menu

FUNCTION

Wall Color

Aspect Ratio

Keystone

Position

DESCRIPTION

Corrects the projected picture’s color when the projection

surface is not white. See "Using Wall Color" on page 30 for

details.

There are four options to set the image's aspect ratio depending on your input signal source. See

"Selecting the aspect ratio" on page 27 for details.

Corrects any keystoning of the image. See

"Correcting keystone" on page 26 for details.

Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum.

Adjusts the clock phase to reduce image distortion.

Phase

H. Size

Digital Zoom

3D Sync

The function is only available when a PC signal (analog RGB) is selected.

Adjusts the horizontal width of the image.

The function is only available when a PC signal (analog RGB) is selected.

Magnifies or reduces the projected image. See "Magnifying and searching for details" on page 27 for details.

This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view the 3D images.

• For a PC type signal:

When the vertical frequency is 120Hz, and the content being projected is made with 3D technology, selecting

On

will present the 3D images.

• For a video type signal:

When the content being projected is made with 3D technology, selecting

On

will present the 3D images.

When the 3D Sync function is on:

•The brightness level of the projected image will decrease.

•The Preset Mode cannot be adjusted.

•The Keystone can only be adjusted within limited degrees.

•The Digital Zoom can only magnify the pictures to limited sizes.

3D Sync

Invert

When you discover the inversion of the image depth, enable this function to correct the problem.

Operation 39

Downloaded from ProjectorsManual.com Manuals

40

FUNCTION

Preset Mode

Brightness

Contrast

Color

Tint

Sharpness

Brilliant

Color

Color

Temperature

DESCRIPTION

Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See

"Selecting a picture mode" on page 29 for details.

Adjusts the brightness of the image. See

"Adjusting Brightness" on page 30 for details.

Adjusts the degree of difference between dark and light in the

image. See "Adjusting Contrast" on page 30 for details.

Adjusts the color saturation level -- the amount of each color in a video image. See

"Adjusting Color" on page 31 for details.

Adjusts the red and green color tones of the image. See

"Adjusting Tint" on page 31 for details.

The function is only available when Video or S-Video with NTSC system is selected.

Adjusts the image to make it look sharper or softer. See

"Adjusting Sharpness" on page 31

for details.

Adjusts white peaking while maintaining correct color

presentation. See "Adjusting Brilliant Color" on page 31 for

details.

See "Selecting a Color Temperature" on page 31

for details.

3D Color

Management

See "3D Color Management" on page 32 for details.

Save

Settings

Saves the settings made for

User

mode.

Quick Auto

Search

See "Switching input signal" on page 24

for details.

FUNCTION

Presentation

Timer

Language

Projector

Position

DESCRIPTION

Reminds the presenter to finish the presentation within a

certain time frame. See "Setting the presentation timer" on page 33

for details.

Sets the language for the On-Screen Display (OSD) menus.

See "Using the menus" on page 21

for details.

The projector can be installed on a ceiling or behind a screen.

See "Choosing a location" on page 9

for details.

Auto Power

Off

Blank Timer

Allows the projector to turn off automatically if no input signal is

detected after a set period of time. See "Setting Auto Power

Off" on page 45 for details.

Sets the image blank time when the Blank feature is activated,

once elapsed the image will return to the screen. See "Hiding the image" on page 34 for details.

Panel Key

Lock

Timer

Controller

Splash

Screen

Disables or enables all panel key functions except

POWER

on the projector and keys on the remote control. See "Locking control keys" on page 34 for details.

Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours.

Allows you to select which logo screen will display during projector start-up. Three options are available: InFocus logo,

Black screen, or Blue screen.

Downloaded from ProjectorsManual.com Manuals

Operation 41

42

FUNCTION DESCRIPTION

Selecting

On

enables the function and the projector cooling time will be shortened to a few seconds.

Quick

Cooling

If you attempt to restart the projector right after the quick cooling process, it may not be turned on successfully and will rerun its cooling fans.

High Altitude

Mode

A mode for operation in high altitude areas. See

"Operating in a high altitude environment" on page 35

for details.

Audio

Settings

Menu

Settings

Closed

Caption

Mute

Volume

See "Adjusting the sound" on page 35 for details.

Menu display time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu position

Sets the On-Screen Display (OSD) menu position.

Closed Caption Enable

Activates the function by selecting

On

when the selected input signal carries closed captions.

• Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings).

Caption Version

Selects a preferred closed captioning mode. To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).

FUNCTION

VGA Out

Lamp

Settings

Security

Settings

Reset All

Settings

Current

System

Status

DESCRIPTION

Selecting

On

enables the function. The projector can output a

VGA signal when it is in standby mode and the

D-SUB IN

and

D-SUB OUT

sockets are correctly connected to devices. See

"Connecting a monitor" on page 15

for how to make the connection.

Enabling this function slightly increases the standby power consumption.

Lamp mode

See "Setting Lamp mode as Economic" on page 45 for details.

Reset lamp timer

See "Resetting the lamp timer" on page 49 for details.

Equivalent lamp hour

S

ee "Getting to know the lamp hour" on page 45 for details

on how the total lamp hour is calculated.

Change password

You will be asked to enter the current password before changing to a new one.

Power on lock

See "Utilizing the password function" on page 22 for details.

Returns all settings to the factory preset values.

The following settings will still remain: Position, Phase, H. Size,

User, Language, Projector Position, High Altitude Mode,

Security Settings.

Source

Shows the current signal source.

Preset Mode

Shows the selected mode in the

PICTURE

menu.

Resolution

Shows the native resolution of the input signal.

Color System

Shows input system format, NTSC, PAL, SECAM, or RGB.

Equivalent Lamp Hour

Displays the number of hours the lamp has been used.

Downloaded from ProjectorsManual.com Manuals

Operation 43

Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean.

Never remove any parts of the projector except the lamp. If your projector needs service, contact InFocus Corporation (www.infocus.com/support) or your dealer for assistance.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

• Use a canister of compressed air to remove dust.

If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

CAUTION

Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown

procedure as described in "Shutting down the projector" on page 36

and unplug the power cord.

• To remove dirt or dust, wipe the case with a soft, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

CAUTION

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

• Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to

"Specifications" on page

52

or consult your dealer about the range.

Retract the adjuster feet.

Remove the battery from the remote control.

Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

44

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The timer displays lamp hours used in

Normal

mode, plus equivalent

Economic

mode hours. Equivalent

Economic

mode hours are calculated as follows:

1 lamp hour (in

Normal

mode) = 1.33 lamp hours (in

Economic

mode)

See "Setting Lamp mode as Economic"

below for more information on Economic mode.

To obtain the lamp hour information:

1.

Press

MENU/EXIT

and then press /

Advanced

menu is highlighted.

until the

SYSTEM SETUP:

2.

highlight and press

MODE/ENTER

. The

Lamp

3.

4.

Settings

page displays.

You will see the

Equivalent lamp hour

To leave the menu, press

MENU/EXIT

.

information displaying on the menu.

You can also get the lamp hour information on the

INFORMATION

menu.

Extending lamp life

The projection lamp is a consumable item. To keep the lamp life as long as possible, you can do the following settings via the OSD menu.

Setting Lamp mode as Economic

Using

Economic

mode reduces system noise and power consumption by 20%. If the

Economic

mode is selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in

Economic

mode also extends the lamp operation life. To set

Economic

mode, go into the

SYSTEM SETUP: Advanced

>

Lamp Settings

>

Lamp mode

menu and press / .

Setting Auto Power Off

This function allows the projector to turn off automatically if no input source is detected after a set period of time to prevent unnecessary waste of lamp life.

To set

Auto Power Off

, go into the

SYSTEM SETUP: Basic

>

Auto Power Off

menu and press / . The time period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your presentation, select

Disable

. The projector will not automatically shut down in a certain time period.

Downloaded from ProjectorsManual.com Manuals

Maintenance 45

46

Timing of replacing the lamp

When the

Lamp indicator

lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

CAUTION

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator

still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 50 for details.

The following lamp warning displays will remind you to change the lamp.

Status

The lamp has been in operation for 3500 hours. Install a new lamp for optimal performance. If the projector is normally run with

Economic

selected (See

"Setting Lamp mode as Economic" on page 45 ), you may

continue to operate the projector until the

3950 hour lamp warning appears.

Message

Notice

Order Replacement Lamp

Lamp > 3500 Hours

OK

The lamp has been in operation for 3950 hours. A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time.

Notice

Replace Lamp Soon

Lamp > 3950 Hours

OK

The lamp has been in operation for 4000 hours.

It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. If the lamp is not replaced beforehand, it must be replaced after 4000 hours usage.

The lamp MUST be replaced before the projector will operate normally.

Notice

Replace Lamp Now

Lamp > 4000 Hours

Lamp usage time exceeded

OK

Notice

Lamp-usage time exceeded

Replace lamp (refer to Reference Guide)

Then reset lamp timer

OK

Replacing the lamp

WARNING

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org

To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

1.

2.

To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp edges in the lamp compartment. Wash hands after lamp replacement.

Only InFocus certified lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.

Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

Turn the projector over. Then loosen the screws on the lamp cover.

3.

Remove the lamp cover from the projector.

WARNING

Do not turn the power on with the lamp cover removed.

4.

Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

Loosen the screw that secures the lamp.

Downloaded from ProjectorsManual.com Manuals

Maintenance 47

48

5.

Pull out the lamp connector from a slot in the lamp compartment.

Disconnect it from the projector as illustrated.

6.

Lift the handle so that it stands up.

Use the handle to slowly pull the lamp out of the projector.

CAUTION

Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

7.

8.

Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

Insert the new lamp into the lamp compartment and make sure it fits in the projector.

Reconnect the lamp connector and place it back into its slot to be flush with the projector.

2 1

2

9.

Tighten the screw that secures the lamp.

CAUTION

Loose screw may cause a bad connection, which could result in malfunction.

10.

11.

Do not over tighten the screw.

Ensure the handle is fully laid flat and locked in place.

Replace the lamp cover on the projector.

12.

Tighten the screws that secure the lamp cover.

CAUTION

Loose screw may cause a bad connection, which could result in malfunction.

Do not over tighten the screws.

13.

Restart the projector.

CAUTION

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

14.

After the startup logo, open the On-

Screen Display (OSD) menu. Go to the

SYSTEM SETUP: Advanced

>

Lamp

Settings

menu. Press

MODE/ENTER

.

The

Lamp Settings

page displays.

Notice

Reset Lamp Timer?

Reset Cancel

highlight and press

MODE/ENTER

. A warning message displays asking if you want to reset the lamp timer. Highlight

Reset

and press

MODE/ENTER

. The lamp time will be reset to '0'.

CAUTION

Do not reset if the lamp is not new or replaced as this could cause damage.

Downloaded from ProjectorsManual.com Manuals

Maintenance 49

50

Indicators

Light

Power Temp

Status & Description

Lamp

Power events

Orange Orange

Off

Orange

Off

The projector has just been connected to a power outlet.

Stand-by mode

Orange

Green

Flashing

Green

Off

Off

Off

Off

Powering up

Orange

Flashing

Orange

Flashing

Off

Off

Off

Off

Normal operation

1.

2.

The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process.

Or

The projector needs to cool for 90 seconds after the power is turned off.

The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.

Lamp events

Orange

Flashing

Off

Off

Off

Red

Red

The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.

1.

2.

The projector needs 90 seconds to cool down.

Please contact your dealer for assistance.

Or

Thermal events

Off

Off

Off

Off

Red

Red

Red

Green

Green

Green

Orange

Orange

Orange

Off

Off

Red

Red

Red

Red

Red

Green

Green

Red

Red

Red

Red

Red

Red

Red

Red

Off

Red

Green

Orange

Red

Green

Orange

Red

Green

Orange

Red

Green

Orange

Red

Green

The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.

Troubleshooting

The projector does not turn on.

Cause

There is no power from the power cable.

Attempting to turn the projector on again during the cooling process.

Remedy

Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on.

Wait until the cooling down process has completed.

No picture

Cause

The video source is not turned on or connected correctly.

The projector is not correctly connected to the input signal device.

Remedy

Turn the video source on and check that the signal cable is connected correctly.

Check the connection.

The input signal has not been correctly selected.

The lens cover is still closed.

Select the correct input signal with the

SOURCE

key on the projector or remote control.

Open the lens cover.

Blurred image

Cause

The projection lens is not correctly focused.

The projector and the screen are not aligned properly.

The lens cover is still closed.

Remedy

Adjust the focus of the lens using the focus ring.

Adjust the projection angle and direction as well as the height of the unit if necessary.

Open the lens cover.

Remote control does not work

Cause

The battery is out of power.

There is an obstacle between the remote control and the projector.

You are too far away from the projector.

Remedy

Replace the battery with new one.

Remove the obstacle.

Stand within 8 meters (26 feet) of the projector.

The password is incorrect

Cause

You do not remember the password.

Remedy

Please see

"Entering the password recall procedure" on page 23 for details.

Troubleshooting 51

Downloaded from ProjectorsManual.com Manuals

Specifications

Projector specifications

All specifications are subject to change without notice.

General

Product name

Model name

Optical

Resolution

Display system

Lens F/Number

Lamp

Electrical

Power supply

Power consumption

Mechanical

Weight

Input terminal

Computer input

RGB input

Video signal input

S-VIDEO

VIDEO

SD/HDTV signal input

Digital Projector

IN102

800

x

600 SVGA

1-CHIP DMD

1024

x

768 XGA

F = 2.56 to 2.8, f = 21 to 23 mm (0.83

to 0.91”)

SHP 220 W lamp UHP 210 W

AC100–240V, 2.9 A, 50/60 Hz (Automatic)

315 W (Max)

2.4 Kg (5.29 lbs)

D-Sub 15-pin (female)

x

2

IN104

Mini DIN 4-pin port

x

1

RCA jack

x

1

Analog – D-Sub <–> Component RCA jack

x

3

(through RGB input)

PC audio jack x 1 Audio signal input

Output terminal

RGB output

Speaker

Audio signal output

Control terminal

D-Sub 15-pin (female)

x

1

2 watt

x

1 (Amp 1 W)

PC audio jack x 1

RS-232 serial control 8 pin

x

1 (male)

Environmental Requirements

Operating temperature

Operating relative humidity

Operating altitude

0°C–40°C at sea level

10%–90% (without condensation)

0–1499 m at 0°C–35°C

1500–3000 m at 0°C–30°C (with

High Altitude

Mode

on)

52

Dimensions

264 mm

x

96.1 mm

x

225 mm (10.4”

x

3.8”

x

8.9”) (W

x

H

x

D)

264 mm (10.4”)

225 mm

(8.9”)

96.1 mm

(3.8”)

60 mm (2.4”) 66 mm (2.6”)

Timing chart

Supported timing for PC input

Resolution

640 x 350

640 x 400

640 x 480

720 x 400

720 x 480

Horizontal Frequency

(kHz)

37.861

37.861

Vertical Frequency

(Hz)

85.08

85.08

Pixel Frequency

(MHz)

640

640 x x

350_85

400_85

31.469 60.000

VGA_60

37.861 72.809 VGA_72

37.500 75.000 VGA_75

43.269 85.008 VGA_85

31.469

37.927

59.940

85.039

720

720 x x

400_60

400_85

31.469

35.156

59.940

56.25

720 x 480_60

SVGA_56

800 x 600

1024 x 768

1152 x 864

1280 x 768

1280 x 800

1280 x 1024

48.363 60.004 XGA_60

56.476 70.069 XGA_70

60.023 75.029 XGA_75

68.667 84.997 XGA_85

63.815

67.5

70.012

75

1152

1152 x x

864_70

864_75

77.094

47.776

60.289

68.633

49.702

84.999

59.87

74.893

84.837

59.81

1152 x 864_85

1280 x 768_60

1280 x 768_75

1280 x 768_85

WXGA_60

79.976

91.146

75.025

85.024

SXGA_75

SXGA_85

Specifications 53

Downloaded from ProjectorsManual.com Manuals

54

1280 x 960

1360 x 768

1440 x 900

1400 x 1050

1600 x 1200

1680 x 1050

1920 x 1200

640 x [email protected]

832 x [email protected]

1024 x [email protected]

1152 x [email protected]

1152 x [email protected]

1152 x [email protected]

1024 x [email protected]

1024 x [email protected]

60.000

75.000

85.938

47.712

55.935

65.317

75.000

65.290

74.038

35.000

49.722

60.241

68.68

61.796

71.713

35.820

37.500

60.000

75.000

85.002

60.015

59.887

59.978

60.000

59.954

59.95

66.667

74.546

75.020

75.06

65.95

76.047

60.000

60.000

Supported timing for Component-YP b

P r input

1280 x 960_60

1280 x 960_75

1280 x 960_85

1360 x 768_60

WXGA+_60

SXGA+_60

UXGA_60

1680 x 1050_60

1920 x 1200_60

MAC13

MAC16

MAC19

MAC21

SUN1166X

SUN1176X

D1057660

DMT10600

Signal Format

480i(525i)@60Hz

480p(525p)@60Hz

576i(625i)@50Hz

576p(625p)@50Hz

720p(750p)@60Hz

720p(750p)@50Hz

1080i(1125i)@60Hz

1080i(1125i)@50Hz

[email protected]

[email protected]

Horizontal Frequency (kHz)

15.73

31.47

15.63

31.25

45.00

37.50

33.75

28.13

67.5

56.26

Vertical Frequency (Hz)

59.94

59.94

50.00

50.00

60.00

50.00

60.00

50.00

60.00

50.00

Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.

Supported timing for video and S-Video inputs

Video mode

NTSC-M

PAL

SECAM

PAL-M

PAL-N

PAL-60

NTSC4.43

Horizontal

Frequency (kHz)

15.73

15.63

15.63

15.73

15.63

15.73

15.73

Vertical Frequency

(Hz)

60

50

50

60

50

60

60

Color sub-carrier

Frequency (MHz)

3.58

4.43

4.25 or 4.41

3.58

4.43

4.43

4.43

Copyright information

Copyright

Copyright 2010 by InFocus Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of InFocus Corporation.

Disclaimer

InFocus Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, InFocus

Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments.

Others are copyrights of their respective companies or organizations.

Downloaded from ProjectorsManual.com Manuals

Copyright information 55

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents