Boxlight CD-600m Projector User Guide

Copyright © 2001 by BOXLIGHT
Poulsbo, Washington. All rights reserved.
Downloaded from ProjectorsManual.com Manuals
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TÜV, NOM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Downloaded from ProjectorsManual.com Manuals
Declaration of Conformity
Manufacturer: BOXLIGHT
19332 Powder Hill Place, Poulsbo, Washington, USA
We declare under our sole responsibility that the CD-600m and CD-750m projectors conform to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 1992 + A1 + A2 + A3 + A4: 1997
July, 2001
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows are
trademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or registered trademark of Texas Instruments.
Downloaded from ProjectorsManual.com Manuals
Downloaded from ProjectorsManual.com Manuals
TABLE OF CONTENTS
Safety Instructions
iii
Introduction
Image Resolution
Compatibility
Unpacking the Projector
Usage Guidelines
If You Need Assistance
Warranty
1
1
2
2
5
5
5
Setting up the Projector
Connecting a Computer
Connecting a Video Device
Using the optional enhanced connectivity module
Powering up the Projector
Turning Off the Projector
7
9
10
12
14
17
Using the Projector
Basic Image Adjustment
Adjusting the Projector
Using the Remote Control
Using the Keypad and Remote Buttons
Using the On-Screen Menus
Display Menu
Audio Menu
Image Menu
Color Management Menu
Control Menu
Advanced Menu
Language Menu
Status Menu
19
19
19
21
22
25
26
28
29
32
33
34
35
36
i
Downloaded from ProjectorsManual.com Manuals
T a
b
l
e
o
f
C
o
n
t
e
n
t
s
Maintenance & Troubleshooting
Cleaning the Lens
Replacing the Projection Lamp
Replacing the Batteries in the Remote Control
Using the Security Lock
Troubleshooting
37
37
37
40
40
41
Appendix
Specifications
Accessories
Portable and Laptop Activation Chart
Using Video Mirroring with a PowerBook Computer
Projected Image Size
45
45
46
48
53
54
Index
55
ii
Downloaded from ProjectorsManual.com Manuals
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
• Warning: Statements identify conditions or practices that
could result in personal injury.
• Caution: Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention: For information about usage of a feature, please
refer to the User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
Safety Terms:
• Warning: Don’t look directly into the lens when the lamp is
turned on.
•Warning: To replace the lamp, turn off the projector
and unplug the power cord. To avoid burns, wait 30 minutes before opening the lamp door. Follow all instructions provided in this User’s Guide.
•Warning: Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
• Warning: Refer all service to qualified service personnel. Ser-
vicing your own projector will void the warranty. See the following page for the customer service contact information.
• Caution: Don’t block ventilation openings.
iii
Downloaded from ProjectorsManual.com Manuals
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
• Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
• Caution: Don’t place the projector on a hot surface or in direct
sunlight.
• Caution: Do not drop the projector. Transport the projector in a
BOXLIGHT-approved case; see page 46 for a list of cases.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb rupturing, thoroughly clean the area in front of the projector and discard any edible items placed in that area.
)
6m
t (.
2f
Do not place objects in
this area in front of the projector
Customer Service
If you need assistance, call BOXLIGHT at 1-800-762-5757 or
360-779-7901.
iv
Downloaded from ProjectorsManual.com Manuals
INTRODUCTION
The BOXLIGHT® CD-600m™ and CD-750m™ multimedia projectors are specifically designed for multipurpose use. They generate crisp, clear images using Digital Light Processing™ (DLP)
technology. They are easy to connect, easy to use, easy to transport, and easy to maintain. The CD-600m has native SVGA
800x600 resolution, the CD-750m has XGA 1024x768 resolution.
The user interfaces of the two products are identical except where
noted; information in this user’s guide applies to both products.
Image Resolution
CD-600m
The SVGA resolution of the CD-600m’s projected image is
800x600. The projector is compatible with screen resolutions up to
1280x1024. If your computer’s screen resolution is higher than
1280x1024, reset it to a lower resolution before you connect the
projector.
NOTE: The CD-600m automatically expands 640x480 images to
800x600. You can display these
images at their native resolutions
by turning off the Auto Resize feature. See “Resize” on page 29 for
CD-750m
The XGA resolution of the CD-750m’s projected image is
1024x768. The projector is compatible with screen resolutions up
to 1280x1024. If your computer’s screen resolution is higher than
1280x1024, reset it to a lower resolution before you connect the
projector.
more information.
NOTE: The CD-750m automatically expands 640x480 and
800x600 images to 1024x768.
You can display these images at
their native resolutions by turning
off the Auto Resize feature. See
“Resize” on page 29 for more
information.
1
Downloaded from ProjectorsManual.com Manuals
I
n
t
r
o
d
u
c
t
i
o
n
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including laptops, up to 1280x1024
resolution.
• Apple® Macintosh® and PowerBook® computers up to
1280x1024 resolution.
• Most standard VCRs, DVD players, HDTV sources, camcordNOTE: The projector is
compatible with 1080i and 720P
HDTV formats.
ers and laser disc players.
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included. Contact Boxlight immediately if
anything is missing.
If you are experienced in setting up presentation systems, use the
Quick Start card that was included in the shipping box. For complete details on connecting and operating the projector, refer to
this User’s Guide.
2
Downloaded from ProjectorsManual.com Manuals
2
1
me
nu
/se
lec
t
3
key
sto
ne
ba
ck
vid
eo
da
ta
for
wa
rd
4
5
9
6
7
8
FIGURE 1
Shipping box contents
1.
Projector + lens cap
6.
Computer cable
2.
Soft carry case
7.
Audio cable adapter
3.
User’s Guide and quick start
card
8.
Audio cable
4.
Power cord
9.
Composite video cable
5.
Remote control
3
Downloaded from ProjectorsManual.com Manuals
I
n
t
r
o
d
u
c
t
i
o
n
zoom ring
focus ring
FIGURE 2
Front view of projector
keypad
connector panel
FIGURE 3
Back view of projector
4
Downloaded from ProjectorsManual.com Manuals
power
cord
connector
height adjustment
button
Usage Guidelines
• Do not look directly into the projection lens when the lamp is
turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
• Transport the projector in a vendor-approved hard or soft case.
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 41.
If this manual doesn’t answer your question, call BOXLIGHT at
1-800-762-5757 or 360-779-7901.
Warranty
This product is backed by a limited two-year warranty. The
details of the warranty are printed at the back of this manual.
5
Downloaded from ProjectorsManual.com Manuals
I
n
t
r
o
d
u
c
t
i
o
n
6
Downloaded from ProjectorsManual.com Manuals
SETTING UP THE PROJECTOR
1 Place the projector on a flat surface.
• The projector must be within 10 feet (3 m) of your power
source and within 6 feet (1.8 m) of your computer.
• If you want to project from behind a translucent screen, set
up the projector behind your screen. See “Rear Project” on
page 34 to reverse the image.
• If you are installing the projector on the ceiling, refer to the
installation guide that comes with the Ceiling Mount Kit for
more information. To turn the image upside down, see
“Ceiling Project” on page 34. The Ceiling Mount Kit is sold
separately, see “Optional Accessories” on page 46.
2 Position the projector the desired distance from the screen.
• The distance from the lens of the projector to the screen and
the zoom setting determine the size of the projected image.
Figure 4 shows three projected image sizes. For more information about image size, see “Projected Image Size” on
page 54.
NOTE: The projector must be at
least 5 feet (1.5 m) from the projection screen.
11
.8
f t/
3.6
.
m
7.1
.9m
2m
/
ft.
.
/2
f t.
3.0
20 ft./6.1m
12 ft./3.7m
5 ft./1.5m
FIGURE 4
Projected image size at minimum zoom
3 Make sure the projector is unplugged and your computer is
turned off.
7
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
NOTE: Before you continue,
o
r
Audio in
make sure the projector is
S-video
computer
unplugged and your equipment is
composite
video
turned off. If you’re connecting a
computer, make sure the distance
between it and the projector is 6
feet or less.
FIGURE 5
Connector panel
NOTE: The enhanced connectivity
computer 1-M1
audio in
module is an optional accessory
component
video
wired remote
RS-232
that provides RS-232, component
video, VESA computer, M1
computer, and monitor loop
through capabilities. See “Optional
Accessories” on page 46 for
ordering information.
computer 2-VESA
audio in
composite
S-video
audio in video
(for all video sources)
monitor
FIGURE 6
Connector panel on optional enhanced connectivity module
to USB mouse
to computer
FIGURE 7
Computer cable
8
Downloaded from ProjectorsManual.com Manuals
to computer video
to projector
Connecting a Computer
The projector ships with an analog computer cable. If your computer has a digital output, you can order the optional digital computer cable. Using a digital source generates the highest quality
and brightest image possible. See “Optional Accessories” on
page 46.
1 Plug the end of the computer cable with one cable into the
PC 1 connector on the projector.
2 Plug the blue end of the computer cable into the video connector on your computer.
NOTE: Many laptop computers
do not automatically turn on their
external video port when a secondary display device such as a
projector is connected. Refer to
your computer manual for the
computer cable
command that activates the exter-
USB mouse
nal video port. Activation commands for some laptop computers
FIGURE 8
Connecting the projector to a computer
are listed in the Appendix of this
manual on page 48.
Do you want to control the computer’s mouse from the projector’s
remote?
1 Plug the USB cable into the USB mouse connector on your
computer. To use the remote to control your computer’s
mouse, you must install the USB drivers. See page 14 for
details.
NOTE: The USB mouse is supported for use with
Windows 98, Windows ME,
Do you want to play your computer’s audio on the projector?
1 Plug either end of the audio cable into the audio connector on
your computer.
2 Plug the other end of the audio cable into the Audio In connector on the projector.
Now you’re ready to power up the projector and your laptop.
Skip to “Powering up the Projector” on page 14.
Windows 2000, and Apple OS 8.5
and higher only.
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it (it is hot-pluggable).
9
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Connecting a Video Device
1 If your video player uses a round, one-prong composite video
connector, you’ll need only the audio cable, audio adapter,
and composite video cable that shipped with the projector.
• If your video player uses a round, four-prong S-video conNOTE: HDTV sources are
connected to the projector using
nector, you’ll need an S-video cable in addition to the audio
cable and audio adapter. The S-video cable is sold separately. (See “Optional Accessories” on page 46.)
the computer cable. See the
previous pages for details.
2 Plug the composite video cable’s yellow connector into the
“video-out” connector on your video player (Figure 9). This
connector may be labeled “To Monitor.”
• If you’re using an S-video cable, connect it to the “S-video
out” connector on the video player (Figure 10).
3 Plug the other yellow connector into the composite video conon the projector.
nector
• If you’re using S-video, plug the other end of the cable into
the “S-video” connector
on the projector (Figure 10).
audio
adapter
composite video
cable
audio cable
FIGURE 9
Connecting the projector to a video player using the standard video cable (with composite video connector) and the audio cable and adapter
10
Downloaded from ProjectorsManual.com Manuals
audio
adapter
S-video
cable
audio cable
FIGURE 10
Connecting the projector to a video player using an S-video cable and the audio cable
and adapter
4 Plug the audio adapter’s white connector into the left “audio
out” connector on your video player. Plug the adapter’s red
connector into the right “audio out” connector on the video
player (Figure 9 and Figure 10).
NOTE: The audio adapter is provided so that the same audio cable
used to connect a computer can
5 Plug the audio adapter’s other end into the audio cable.
6 Plug the audio cable into the “audio in” connector on the projector.
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, and
SECAM. It automatically adjusts to optimize its performance for
the incoming video.
be used with the adapter to connect a video device.
CAUTION: Your video player
may also have a “Video Out” connector for a coaxial cable connection. DO NOT use this to connect
to the projector.
11
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Using the optional enhanced connectivity module
NOTE: If you have turned Auto
Source off (page 33), you may
need to press the source button on
the keypad more than once to
This module connects to the projector via the projector’s computer connector. Slide the tabs in the module into the grooves on
the back of the projector, then press the computer connector into
the projector. To remove the module, press down on the bumpy
lever on the top left of the module to release the latch, then slide
the module off.
display an active source. The
sources switch in this order:
PC 1-Analog, PC 1-Digital,
PC 2-VESA, Video 3-Component,
Video 1 S-Video, and Video 2Composite.
FIGURE 11
Connecting the optional connectivity module to the projector
computer 1-M1
computer 2-VESA
audio in
audio in
component
video
wired remote
composite
S-video
audio in video
(for all video sources)
FIGURE 12
Connector panel on optional enhanced connectivity module
12
Downloaded from ProjectorsManual.com Manuals
RS-232
monitor
The module provides the following audio/video inputs:
Source
Video
Audio
Computer
2 VESA
VESA Single-ended analog RGB (HD-15)
mini jack
Computer
1 M1-DA
M1-DA Single-ended
analog or digital
mini jack
Component Video
Base-band component
video (RCA)
Left and right line-level
(2 RCAs)
Composite
Video
Base-band composite
video (RCA)
Left and right line-level
(2 RCAs)
S-Video
S-video Y/C (4-pin circular)
Left and right line-level
(2 RCAs)
The module also provides wired remote input (used with an
optional remote), monitor out (used to display images on your
desktop computer’s monitor as well as on the projection screen),
and RS-232 input (to control the projector from an LCD control
panel).
13
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Powering up the Projector
1 Remove the lens cap.
NOTE: Always use the power cord
that shipped with the projector.
2 Plug the power cord into the side of the projector, then plug it
into your electrical outlet. A surge-protected power strip is
recommended.
• The LED on the top of the projector (Figure 17 on page 22)
lights green.
3 Turn on the lamp by pressing the green power button on the
keypad or remote.
• A tone sounds when you press the button, and the LED
blinks green while the software initializes. When initialization is complete, the LED lights solid green and the startup
screen appears.
4 If you connected a video player, turn it on.
• The video image should display on the projection screen. If
it doesn’t, press the source button on the keypad or the
video button on the remote to display your video image.
You can select a default source to determine which source
the projector examines first during power-up for active
video; see “Default Source” on page 33.
• Use the volume buttons to adjust the volume.
5 Turn on your computer.
For Windows 98:
a The first time you connect a particular computer to the projector, the computer recognizes the projector as “new hardware” and the Add New Hardware Wizard appears. Follow
these instructions to use the Wizard to load the correct
driver (which was installed with your Windows operating
system).
14
Downloaded from ProjectorsManual.com Manuals
Click Next. Make sure “Search for the best driver” is selected,
then click Next.
Uncheck any checked boxes, then click Next. Windows automatically locates the driver. If this driver has been removed, reload
the driver using your Windows operating system CD.
15
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
When Windows finds the driver, you are ready to install it. Click
Next.
Click Finish when installation is complete.
NOTE: The USB mouse is
supported for use with Windows
98, Windows ME, Windows 2000,
and Apple OS 8.5 and higher only.
Windows NT is not supported.
b If you connected the USB cable (page 9), the Add New
Hardware Wizard appears again. Drivers must be installed
to use the remote to control your computer’s mouse.
The Wizard is launched three times. The first time it detects
a USB Composite Device, the second time a USB Human
Interface Device (for the keyboard), and the third time a
USB Human Interface Device (for the mouse). The required
drivers are located on your Windows operating system and
on the Window operating system CD.
For Windows 2000 and Windows ME:
a The USB drivers for mouse control are automatically
installed.
For a Macintosh computer running Mac OS X:
a The USB drivers for mouse control are automatically
installed.
16
Downloaded from ProjectorsManual.com Manuals
6 The computer image should display on the projection screen.
If it doesn’t, press the source button on the keypad or the data
button on the remote to display your computer’s image. Make
sure your laptop’s external video port is activated; see “Portable and Laptop Activation Chart” on page 48 for details.
• If necessary, make adjustments to the image using the pro-
jector’s on-screen menus. To open the menus, press the
menu/select button on the keypad or remote, then select the
Display or Image sub-menu. For more information about
the menus, see page 25.
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
Turning Off the Projector
If you want to turn off the projector for a short period of time,
press the standby button on the keypad or remote. This blanks the
screen for fifteen minutes, but keeps the projector running. (You
can change the amount of time the projector stays in standby
mode; see page 33 for details.) After 15 minutes, the lamp goes
out. To exit standby mode, press the standby button again. (It may
take several seconds for the projection lamp to reach full power
and project the image again.) See page 24 for details on standby
mode.
To turn off the projector, press the power button. The lamp turns
off and the LED blinks orange for a minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights green and the fans stop. Unplug the power cord to completely power off the projector.
NOTE: Lamp life will be extended
if you turn the power off, then wait
1 minute while the lamp cools
before unplugging the projector.
The Lamp LED will light green
when the lamp has cooled.
17
Downloaded from ProjectorsManual.com Manuals
S
e
t
t
i
n
g
u
p
t
h
e
18
Downloaded from ProjectorsManual.com Manuals
P
r
o
j
e
c
t
o
r
USING THE PROJECTOR
This section describes how to use and make adjustments to the
projector. It also provides a reference to the keypad and remote
buttons and the options available from the on-screen menus.
Basic Image Adjustment
1 Make sure you have powered up your equipment in the right
order (page 14).
2 If the image doesn’t display completely, zoom the image
(page 19), adjust the height of the projector (page 20) or center
the image by adjusting its horizontal or vertical position
(page 31). Be sure the projector is at a 90 degree angle to the
screen.
3 If the image is out of focus, rotate the focus lens (page 19).
4 If the colors don’t look right, adjust the brightness, contrast,
tint, or color (page 26).
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 13) until the
image is clear. To zoom the image, rotate the zoom ring. This
adjusts the image size. You can also zoom in on part of the image,
see page 24.
zoom ring
NOTE: To obtain the best overall
focus quality, open the menu and
focus on the text. This will ensure
that the best overall image quality
is achieved.
focus ring
FIGURE 13
Focus ring and zoom ring
19
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
The projector is equipped with a self-locking, quick-release elevator foot and button.
To raise the projector:
1 Press and hold the elevator button (Figure 14).
2 Raise the projector to the height you want, then release the
button to lock the elevator foot into position.
elevator button
(under finger)
elevator foot
FIGURE 14
Adjusting the height of the projector
3 If necessary, turn the leveling knob to adjust the angle of the
projected image.
FIGURE 15
Turning the leveling knob
20
Downloaded from ProjectorsManual.com Manuals
Using the Remote Control
To control the computer’s mouse from the projector’s remote,
you must connect the USB connector on the computer cable to the
computer. See page 9 for details.
Point the remote control at the projection screen or at the front or
back of the projector (not at the computer). The range for optimum operation is about 25 feet. If you point the remote at the
projection screen, the distance to the screen and back to the projector must be less than or equal to 25 feet. For best results, point
the remote directly at the projector.
menu/
select
power
zoom +
zoom -
forward
backward
keystone
zoom mode
data
standby
video
FIGURE 16
Remote control
21
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the Keypad and Remote Buttons
While the menus are displayed, the volume, source, and standby
buttons on the keypad act as menu navigation buttons. See
“Using the On-Screen Menus” on page 25 for details.
power
LED
menu/
select
power
menu
zoom +
zoom -
source
forward
backward
volume -
volume +
keystone
zoom mode
data
standby
video
standby
FIGURE 17
Keypad and remote buttons
NOTE: If you have turned Auto
Source off (page 33), you may
need to press the source button
more than once to display an
active source. The sources switch
in this order: PC 1-Analog,
PC 1-Digital, Video 1 S-Video, and
Menu/select
Press the menu/select button to open the on-screen menus. Press
menu/select again (while Exit is highlighted) to close the menus.
(The menus automatically close after 30 seconds if no buttons are
pressed.) When you close the menus, the projector saves any
changes you made. For more information about the on-screen
menus, see page 25.
Mouse buttons (keypad only)
Use the mouse buttons to zoom in and out on the image. See
“Zoom mode” on page 24 for details.
Video 2-Composite.
Source (keypad only)
or Data and Video (remote only)
When you have more than one source (computer and video) connected to the projector, select between them by pressing the
source button on the keypad or the data or video button on the
remote.
22
Downloaded from ProjectorsManual.com Manuals
Keystone + - (remote only) or Right mouse button (keypad only)
Use this feature to adjust the image vertically and make a squarer
image.
1 Press the keystone + button to reduce the upper part of the
image, and press the keystone - button to reduce the lower
part. You can also adjust keystone from the Display menu (see
page 26 for details on the menu).
increasing keystone
decreasing keystone
FIGURE 18
Adjusting the keystone
Forward/back buttons (remote only)
These buttons act like the page up and page down buttons on
your computer’s keyboard. You can use them to advance through
a slide show in PowerPoint™ presentations. To use this feature,
you must connect the USB mouse connector on the computer
cable to your computer. See page 9 for details.
Up/down/left/right arrow buttons (remote only)
Use these buttons to navigate through and make adjustments to
the on-screen menus. See “Using the On-Screen Menus” on
page 25 for details.
Power button
This turns the lamp on and off. See page 14 for startup and shutdown details.
23
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Zoom mode
This activates the zoom feature. When you press this button, the
zoom icon appears in the lower right corner of the screen. Press
the zoom + button to zoom in on part of the image, press the
zoom - button to zoom out. When the image is zoomed, you can
use the up/down/left/right arrow buttons to display a different
part of the zoomed image (pan the image). Press zoom mode
again to exit the mode and return the image to normal size.
You can also turn Zoom mode on using the Image menu and
zoom and pan the image using the mouse buttons and arrows on
the keypad. See page 30 for details.
Zoom +/-
This allows you to zoom in and out on a part of the image.
Standby
When you press standby, the display and audio turn off and a
blank screen is displayed for 15 minutes. You can change the
amount of time the projector stays in standby mode; see page 33
for details. The LED lights orange while the projector is in
standby.
• If you press standby again within 15 minutes, the projector
returns to normal operations immediately. The LED changes
from orange to green.
• If you don’t press standby again, the lamp turns off after 15
minutes. The LED blinks orange and the fans run while the
projector cools down, then the projector shuts off and the LED
lights solid green.
Volume (keypad only)
To increase the volume, press volume +
ume, press volume -
24
Downloaded from ProjectorsManual.com Manuals
.
. To decrease the vol-
Using the On-Screen Menus
The projector has menus that allow you to make image adjustments and change a variety of settings. These adjustments aren’t
available directly from the keypad.
To open the on-screen menus, press the menu/select button on the
keypad or remote. (The menus automatically close after 60
seconds if no buttons are pressed.) This displays the Main menu
and changes the volume, source, and standby buttons on the
keypad to menu navigation and adjustment buttons (the arrow
LEDs around the buttons light green to indicate the change).
Press the corresponding buttons to move the cursor up and
down, or use the arrow buttons on the remote. The selected menu
is highlighted.
NOTE: Some menu items may be
grayed out (dimmed) at certain
times. This indicates the item is
not applicable to your setup or the
item is not enabled until another
selection is made.
FIGURE 19
Main menu
To change a menu setting, use the up and down arrow buttons to
move the cursor up and down to the item you want to change
(the selected item is highlighted), then press menu/select. When
an item is selected, its button appears depressed to provide a
visual indication of selection. Use the left and right arrows to
adjust the setting or turn it on and off. Press menu/select when
you are done. Press the up and down arrows to move to another
setting. When you have completed your adjustments, navigate to
Exit, then press menu/select. You are returned to the top of the
Main menu. Press menu/select again to exit the Main menu, or
navigate to another submenu.
25
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Display Menu
To access the Display menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight Display, then press menu/select again to access the Display menu.
FIGURE 20
Display menu
Keystone
This option helps to keep the image square as the angle of projection is changed. Use this feature to adjust the image vertically
and make a squarer image. See page 23 for details on keystone
adjustments.
1 Press the down button to highlight Keystone, then press
menu/select. Use the left and right arrows to adjust the keystone setting. Press menu/select to accept your changes.
Brightness
Adjusting the brightness changes the intensity of the image.
1 Use the up and down arrows to highlight Brightness, press
menu/select, use the arrows to adjust the brightness, then
press menu/select to accept your changes.
26
Downloaded from ProjectorsManual.com Manuals
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
1 Use the up and down arrows to highlight Contrast, press
menu/select, use the arrows to adjust the contrast, then press
menu/select to accept your changes.
Tint
The tint adjusts the red-green color balance in the projected
image.
1 Use the up and down arrows to highlight Tint, press
menu/select, use the arrows to adjust the tint, then press
menu/select to accept your changes.
NOTE: The color setting applies
to video sources only. The tint setting applies to NTSC video sources
only.
Color
The color setting adjusts a video image from black and white to
fully saturated color.
1 Use the up and down arrows to highlight Color, press
menu/select, use the arrows to adjust the color, then press
menu/select to accept your changes.
Sharpness
This setting adjusts sharpness of a video image.
1 Use the up and down arrows to highlight Sharpness, press
menu/select, use the arrows to cycle through the options soft,
med-soft, medium, med-hard, and hard, then press menu/
select to accept your selection.
Blank screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby.
1 Use the up and down arrows to highlight Blank screen, press
menu/select, use the arrows to cycle through the options blue,
black, and white, then press menu/select to accept your selection.
27
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Audio Menu
FIGURE 21
Display menu
Volume
You can also adjust the volume directly from the projector’s keypad.
1 Use the up and down arrows to highlight Volume, press
menu/select, use the arrows to adjust the volume, then press
menu/select to accept your changes.
Mute
This mutes the sound.
1 Use the up and down arrows to highlight Mute, press
menu/select, use the left or right arrow to turn mute on and off
(a green dot indicates a feature is on), then press menu/select
to accept your changes.
28
Downloaded from ProjectorsManual.com Manuals
Image Menu
To access the Image menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight
Image, then press menu/select again to access the Image menu.
FIGURE 22
Image menu for computer sources
Resize
Resize allows you to select from among four different re-sizing
options. The default is Standard, which resizes the image from its
original version to fit a standard 4x3 aspect ratio screen. Widescreen Letterbox preserves the 16x9 aspect ratio of the original
theater version, but the image is placed in a 4x3 space, so black
bars appear at the top and bottom of the image. Enhanced Widescreen also preserves the aspect ratio of the original theater version and is designed to be used with content that is Enhanced for
Widescreen TVs. This option yields more detail than Widescreen
Letterbox. Native displays the image with no resizing.
Highlight Resize, press menu/select, use the left or right arrow
buttons to cycle through the options, then press menu/select to
select.
29
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Zoom
This allows you to enter zoom mode without using the remote.
Highlight Zoom, press menu/select, use the left or right arrow
buttons to turn zoom mode on, then press menu/select. Exit the
menus to use the zoom feature. The zoom icon appears in the
lower right corner. Use the right mouse button to zoom in and
use the left mouse button to zoom out. Use the keypad navigation buttons on the keypad to pan the zoomed image. To exit
zoom mode, either turn the feature off in the Image menu or
press the zoom mode button on the remote.
Auto Image
The projector automatically adjusts tracking, signal synchronization and vertical and horizontal position for most computers. If
you want to adjust these features manually, you must turn off
Auto image first.
Highlight Auto image, press menu/select, then press the left or
right arrow buttons to turn this feature off and on.
Manual Sync
NOTE: The Manual Sync,
Manual Tracking, Horizontal
Position and Vertical Position
options are available only for
The projector adjusts signal synchronization automatically for
most computers. But if the projected computer image looks fuzzy
or streaked, try turning Auto image off then back on again. If the
image still looks bad, try adjusting the signal synchronization
manually:
1 Turn Auto Image off.
analog computer sources. The
projector sets these options
automatically for digital computer
2 Highlight Manual sync, press menu/select, use the arrow buttons to adjust Manual sync until the image is sharp and free of
streaks, then press menu/select.
and video sources, with no manual
override.
Manual Tracking
The projector adjusts tracking automatically to match the video
signal from your computer. However, if the display shows evenly
spaced, fuzzy, vertical lines or if the projected image is too wide
or too narrow for the screen, try turning Auto Image off then back
on again. If the image is still bad, try adjusting the tracking manually:
1 Turn Auto image off.
2 Highlight Manual tracking, press menu/select, use the arrow
buttons to adjust Manual tracking until the fuzzy vertical bars
are gone, then press menu/select.
30
Downloaded from ProjectorsManual.com Manuals
Horizontal Position
Follow these steps to manually adjust the horizontal position:
1 Turn Auto image off.
2 Highlight Horizontal position, press menu/select, use the
arrow buttons to adjust the Horizontal position, then press
menu/select.
Positioning adjustments are saved when you turn off the projector.
Vertical Position
Follow these steps to manually adjust the vertical position.
1 Turn Auto image off.
2 Highlight Vertical position, press menu/select, use the arrow
buttons to adjust the Vertical position, then press menu/select.
Positioning adjustments are saved when you turn off the projector.
Overscan (video sources only)
This option crops all the edges of the image to remove noise generated on the edges by your source. This option is available for
video sources only.
Video Standard (video sources only)
When Video is set to Auto, the projector attempts to pick the
video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL 60
or SECAM) automatically based on the input signal it receives.
(The video standard options may vary depending on your region
of the world.) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear
“torn.” If this happens, manually select a video standard.
Highlight Video standard, press menu/select, use the left or right
arrows to cycle through the options, then press menu/select to
select.
31
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Color Management Menu
FIGURE 23
Color Management menu
Degamma
This allows you to select a gamma table that has been specifically
tuned for either computer, video, or film input.
Highlight Degamma, press menu/select, use the left or right
arrows to cycle through the options, then press menu/select to
select.
Auto Color Gain
When this feature is On, the projector automatically sets the red,
green, and blue color gains for each source. When it is off, you
can manually adjust the color gains.
Red, Green, Blue
To manually adjust the color gains:
1 Turn Auto Color Gain off.
2 Highlight Red, Green, or Blue, press menu/select, use the
arrow buttons to adjust the gain, then press menu/select.
The settings are saved for each source.
32
Downloaded from ProjectorsManual.com Manuals
Control Menu
To access the Control menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight
Control, then press menu/select again to access the Control menu.
FIGURE 24
Control menu
Auto Source
When this feature is On, the projector automatically finds the
active source, checking the default source first. When this feature
is Off, the projector defaults to the source selected in Default
Source. To display another source, you must manually select one
by pressing the source button on the keypad or the data or video
button on the remote.
Highlight Auto source, press menu/select, then press the left or
right arrow buttons to turn this feature off and on.
Default Source
This determines which source the projector checks first for active
video during power-up. Select among PC 1-Analog, PC 1-Digital,
Video1 S-Video, and Video 2-Composite (also PC 2-VESA and
Video 3-Component when using the optional connectivity module).
Highlight Default source, press menu/select, use the left or right
arrows to cycle through the options, then press menu/select to
select.
Standby Time
This option lets you select how long the lamp stays on and the
blank screen is displayed when the projector enters standby
mode before the projector turns off. Select among 1, 5, 10, 15 and
30 minutes and 1 and 2 hours by clicking the left or right arrow
buttons and cycling through the options.
33
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Advanced Menu
FIGURE 25
Advanced menu
Rear Project
When you turn Rear Project on, the projector reverses the image
so you can project from behind a translucent screen.
Highlight Rear Project, press menu/select, then press the left or
right arrow buttons to turn this feature off and on.
Ceiling Project
When you turn Ceiling Project on, the projector turns the image
upside down for ceiling-mounted projection. Highlight Ceiling
Project, press menu/select, then press the left or right arrow buttons to turn this feature off and on.
Low Power
This setting toggles between on and off. Turn it on to lower the
light output of the lamp, thus extending its life. This also lowers
the fan speed, making the projector quieter.
Display Messages
This setting toggles between On and Off. When this feature is On,
status messages such as “No signal detected” or “Standby
Active” appear in the lower-right corner of the screen.
34
Downloaded from ProjectorsManual.com Manuals
Display Startup Screen
This setting toggles between On and Off. When this feature is On,
the startup screen appears when the projector starts up and
remains until an active source is detected. The startup screen contains contact information. When it is off, a plain black or blue
screen is displayed instead of the startup screen.
Reset
Highlight Reset then press menu/select to reset the options in the
menus (except Language, Video Standard, Ceiling and Rear
Project, and Standby Time) to their original settings.
Language Menu
FIGURE 26
Language menu
You can display the on-screen menus in English, French, German,
Spanish, Portuguese, Chinese, Japanese, or Korean.
1 Press the menu/select button to display the Main menu, press
the arrow buttons to highlight Language, then press
menu/select again to access the Language menu.
2 Press the arrow buttons to highlight the desired language,
then press menu/select. Press menu/select to exit this menu and
return to the Main menu.
35
Downloaded from ProjectorsManual.com Manuals
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Status Menu
This is a read-only menu for informational purposes. To display
the Status menu, highlight Status from the Main menu, then press
menu/select.
FIGURE 27
Status menu
Lamp Hours Used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in
use. Replace the bulb when the brightness is no longer acceptable. See “Replacing the Projection Lamp” on page 37 for details.
Computer Resolution (computer sources only)
Shows your computer’s resolution setting. To change this, go to
your computer’s Control Panel and adjust the resolution in the
Display tab. See your computer’s user’s guide for details.
Video Format (video sources only)
Shows the video format being displayed.
Source
Indicates the active source, PC 1-Analog, PC 1-Digital, Video1 SVideo, and Video 2-Composite (also PC 2-VESA and Video 3Component when using the optional connectivity module).
Software Version
Indicates the projector’s software version. This information is
useful when contacting Technical Support.
36
Downloaded from ProjectorsManual.com Manuals
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•clean the lens
•replace the projection lamp
•replace the batteries in the remote
•use the security lock feature
•troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t
apply the cleaner directly to the lens.
• Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular
motion.
3 If you don’t intend to use the projector immediately, replace
the lens cap.
Replacing the Projection Lamp
The lamp hour counter in the Status menu counts the number of
hours the lamp has been in use. Change the lamp when the
brightness is no longer acceptable. You can order new lamp modules from Boxlight. See “Accessories” on page 46 for information.
WARNING: To avoid burns,
allow the projector to cool for at
least 30 minutes before you open
Follow these steps to replace the projection lamp:
the lamp module door. Never
1 Turn off the projector and unplug the power cord.
extract the lamp module while the
2 Wait 30 minutes to allow the projector to cool thoroughly.
projector is operating.
37
Downloaded from ProjectorsManual.com Manuals
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
3 Invert the projector on a soft flat surface, then push the ridge
on the lamp door toward the back (Figure 28). The arrow on
the lamp door should point to the unlock icon on the bottom
of the projector. Lift the door up.
WARNING: Be extremely careful
when removing the lamp module.
In the unlikely event that the bulb
ruptures, small glass fragments
may be generated. The lamp
module is designed to contain
these fragments, but use caution
when removing the lamp module.
FIGURE 28
Removing the lamp door
CAUTION: Never operate the
4 Loosen the two non-removable screws on the outside of the
module (Figure 29).
projector with the lamp door open
or removed. This disrupts the air
flow and causes the projector to
overheat.
FIGURE 29
Loosening the screws on the lamp module
38
Downloaded from ProjectorsManual.com Manuals
5 Lift and grasp the metal bail wire and lift the module out (Figure 30). Dispose of the lamp module in an environmentally
proper manner.
FIGURE 30
Removing the lamp module
6 Install the new lamp module, being sure to align the connectors properly.
WARNING: Do not drop the
7 Push the module in until it is flush with the bottom case of the
projector.
lamp module or touch the glass
8 Tighten the screws on the outside of the module.
cause injury.
bulb! The glass may shatter and
9 Replace the lamp door by inserting the hooks on the lamp
door into the slots on the projector and pressing the lamp door
into place. The arrow on the lamp door should point to the
lock icon on the bottom of the projector. If the lamp door does
not fit properly or bulges out, remove the door and re-seat the
lamp module.
10 Plug in the power cord and press the green power button to
turn the projector back on.
11 To reset the lamp hour counter in the Status window, press
and hold the volume - button, then press the source button
(while still holding down the volume - button) for 5 seconds.
Verify that the counter was reset by viewing the counter in the
Status window.
Downloaded from ProjectorsManual.com Manuals
39
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of operation.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Push the tab on the battery door toward the top of the remote
and lift the door off.
3 Remove the old batteries and dispose of them in an environmentally proper manner.
4 Install two new AAA alkaline batteries. Make sure you install
each in the correct direction.
5 Insert the hooks on the battery door into the remote and press
the tab to re-install the door.
Using the Security Lock
The projector has a security connector for use with a PC Guardian
Cable Lock System (Figure 31). See “Optional Accessories” on
page 46 for ordering information. Refer to the information that
came with the lock for instructions on how to use it to secure the
projector.
FIGURE 31
Installing the security lock
40
Downloaded from ProjectorsManual.com Manuals
Troubleshooting
Problem: The projector is not running
•Make sure that the power cord is properly connected to a fully
functional AC electrical outlet. Make sure that the power cord
is also properly connected to the projector.
•If the projector is plugged into a power strip, make sure the
power strip is turned on.
•Make sure the projector is turned on.
Problem: Projector is running, but nothing appears on projection screen
•Make sure you have removed the lens cap on the projection
lens at the front of the projector.
•Check the projector’s lamp to ensure that it is securely con-
nected in the lamp module. Make sure the lamp door is
installed. See “Replacing the Projection Lamp” on page 37.
Problem: Only the start-up screen displays
•Verify that the cables are connected correctly. See page 9
through page 10 for connection procedures.
•Make sure that the cables do not have any bent pins.
•Verify that the proper input source is connected. See “Source
(keypad only) or Data and Video (remote only)” on page 22.
•You might need to turn everything off and power up the
equipment again in the proper order. Refer to your computer’s documentation to determine the correct order.
•Make sure your laptop’s external video port is turned on. See
the “Portable and Laptop Activation Chart” on page 48 or
your computer’s manual for details.
•Make sure your computer’s video board is installed and con-
figured correctly.
•Make sure your computer has a compatible video board. The
projector isn’t CGA or EGA compatible.
41
Downloaded from ProjectorsManual.com Manuals
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
If you’re using Windows 98:
1 Open “My Computer” icon, the Control Panel folder and
then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1280x1024 or less.
Problem: Color or text not being projected
•You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 26 for more information.
Problem: The screen resolution is not right
•Make sure the computer’s video card is set for a resolution of
no greater than 1280x1024.
Problem: Image isn’t centered on the screen
•Move the projector to reposition the image.
•Reposition the image using the menu. Refer to “Horizontal
Position” on page 31 and “Vertical Position” on page 31.
•Be sure the projector is at a 90 degree angle to the screen.
Problem: Image is too wide or narrow for screen
•Adjust the zoom or projector placement.
•Adjust the resolution of your video card if it’s greater than
1280x1024.
Problem: Image is out of focus
•Turn the projection lens to focus the image.
•Make sure the projection screen is at least 5 feet (1.5 m) from
the projector.
•Check the projection lens to see if it needs cleaning.
Problem: Image and menus are reversed left to right
•Rear projection mode is probably turned on. Turn Rear Projection off in the Controls menu. The image should immediately
return to forward projection. See “Rear Project” on page 34.
42
Downloaded from ProjectorsManual.com Manuals
Problem: the projector displays vertical lines, “bleeding” or
spots
•Adjust the brightness. See “Brightness” on page 26.
•Check the projection lens to see if it needs cleaning.
Problem: no sound
•Adjust volume.
•Verify audio/input connections.
•Adjust audio source.
Problem: Image is “noisy” or streaked
Try these steps in this order.
1 Deactivate the screen saver on your computer.
2 Turn Auto Image off and then back on again. See “Auto
Image” on page 30.
3 Turn Auto Image off and adjust the synchronization and tracking manually to find an optimal setting. See “Manual Sync”
on page 30 and “Manual Tracking” on page 30.
•The problem could be with your computer’s video card. If
possible, connect a different computer.
Problem: Projected colors don’t match the computer or video
player’s colors
•Just as there are differences in the displays of different monitors, there are often differences between the computer image
and the projected image. Adjust the brightness, tint and/or
contrast from the Display menu. See “Brightness” on page 26,
“Tint” on page 27 and “Contrast” on page 27.
Problem: Lamp seems to be getting dimmer
•The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 37.
Problem: Lamp shuts off
•A minor power surge may cause the lamp to shut off. Unplug
the projector, wait at least a minute, then plug it back in.
•Make sure the vents are not blocked.
43
Downloaded from ProjectorsManual.com Manuals
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Before calling BOXLIGHT for assistance, please have the following
information available:
•the projector’s serial number (located on the bottom label)
•the resolution of your computer.
Call Boxlight at 1-800-762-5757 or 360-779-7901.
44
Downloaded from ProjectorsManual.com Manuals
APPENDIX
Specifications
The projector must be operated and stored within the temperature and humidity ranges specified.
Temperature
Operating
50 to 104° F (10 to 40° C) at sea level
50 to 95° F (10 to 35° C) at 10,000 feet
Non-operating
-4 to 158° F (-20 to 70° C)
Altitude
Operating
Non-operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)
Humidity
Operating and non-oper.
10% to 95% relative humidity, non-condensing
Dimensions
10.25 x 3.34 x 11 inches (26 x 8.5 x 28 cm)
with module 10.25 x 3.34 x 12 inches (26 x 8.5 x 30.5 cm)
Weight
5.7 lbs. (2.6 kg) unpacked
with module 6.5 lbs. (2.9 kg)
Optics
Focus Range
5 - 16 feet (1.5-5 m)
Lamp
Type
270-watt SHP lamp
Input Power Requirements
100-120VAC 5A;50/60Hz
200-240VAC 3A; 50Hz
45
Downloaded from ProjectorsManual.com Manuals
A
p
p
e
n
d
i
x
Accessories
Standard Accessories
(ship with the projector)
Quick Start card
User’s Guide
Soft Case
Shipping Box
Analog Computer Cable 6 ft (1.8 m)
Composite Video Cable 6 ft (1.8 m)
Computer Audio Cable 6 ft (1.8 m)
Audio Adapter (RCA to 3.5mm)
Remote
Projection Lamp Module (included in projector)
Lens Cap
NOTE: Use only BOXLIGHTapproved accessories. Other
products have not been tested with
the projector.
Power Cords (one ships with projector, type depends on country)
North American Power Cord
Australian Power Cord
UK Power Cord
European Power Cord
Danish Power Cord
Swiss Power Cord
Optional Accessories
Enhanced Connectivity Module
ATA Case
Deluxe Carry Case
Deluxe Travel Case
Audio/Video Cable (30’;9m)
Digital Computer Cable with USB
46
Downloaded from ProjectorsManual.com Manuals
50’ Mac Cable-Domestic
50’ Mac Cable-International
15’ VGA Extension Cable
50’ VGA Cable-Domestic
50’ VGA Cable-International
USB Ranger 400 System
Ceiling Mount
Black LiteMount Pipe Tubing Extension
LiteMount False Ceiling Plate
Appian Traveler (Digital/Analog CardBus PC Card
PC Guardian Projector Cable Lock
Executive Plus Remote
Executive Remote IR Receiver
Full-Feature LaserPro Remote Control
Remote Point RF Remote with Laser Pointer (US,
Mexico, Canada, UK only)
GyroMouse Presenter RF Remote Control (US,
Mexico, Canada, UK only)
GyroMouse Pro RF Remote (US, Mexico, Canada,
UK only)
Remote Point RF Remote with LaserPointer (US
and Canada only)
1-in-2-out VGA Distribution Amplifier
Deluxe Wheeled Projector and Computer Cart
Macintosh Adaptor
40” Portable Projection Screen
50” Portable Projection Screen
60” Deluxe Insta-Theatre Screen
Portable Projector Stand
eBeam (Web Enabled Electronic Meeting
Assistant)
Projection Lamp Module
47
Downloaded from ProjectorsManual.com Manuals
A
p
p
e
n
d
i
x
Portable and Laptop Activation Chart
Many laptop computers do not automatically turn on their external video port when a projector is connected. Activation commands for some laptop computers are listed in the following
table. (If your computer is not listed or the given command does
not work, refer to the computer’s documentation for the appropriate command.) On many laptops, the activation function key
is labeled with an icon, for example
NOTE: Usually, pressing the key
or the text CRT/LCD.
commands once activates the
Computer
Key command to
activate port
Key command to
de-activate port
external video port, pressing it
Acer
Ctrl-Alt-Esc (for setup)
Ctrl-Alt-Esc (for setup)
AST* **
FN-D or Ctrl-D
FN-D or Ctrl-D
and internal ports, and pressing it
Ctrl-FN-D
Ctrl-FN-D
a third time activates the internal
FN-F5
FN-F5
type from A:/IVGA/CRT
type from A:/IVGA/CRT
FN-F12
FN-F12
AMS
FN-F2
FN-F2
AMT
setup screen
setup screen
AT&T
FN-F3
FN-F6
FN-F3
FN-F6
Advanced Logic
Research
Ctrl-Alt-V
Ctrl-Alt-V
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
Conf.Simulscan
setup VGA/
Conf.Simulscan
FN-F12
FN-F12
FN-F5
FN-F5
F2/Choose Option/F5
F2/Choose Option/F5
again activates both the external
port. Refer to your computer’s
documentation for details on your
specific model.
Ambra**
Amrel* **
setup menu
setup menu
Shift-Ctrl-D
Shift-Ctrl-D
Apple
see Mac Portable and Mac PowerBook
Aspen
automatic
automatic
Award
FN-F6
FN-F6
BCC*
automatic
reboot computer
48
Downloaded from ProjectorsManual.com Manuals
Key command to
activate port
Key command to
de-activate port
Bondwell
LCD or CRT options after
bootup
reboot for LCD or CRT
options to appear
Chaplet**
setup screen
setup screen
FN-F6
FN-F6
FN-F4
FN-F4
Computer
Chembook
FN-F6
FN-F6
Commax
Ctrl-Alt-#6
Ctrl-Alt-#5
Compaq* **
Ctrl-Alt-<
Ctrl-Alt->
FN-F4
FN-F4
Compuadd* **
automatic
automatic
mode/? (for setup option)
mode/? (for setup option)
automatic
automatic
Alt-F for screen setup
option
Alt-F for screen setup
option
Data General
Ctrl-Alt-Command
Ctrl-Alt-Command
Data General
Walkabout
2 CRT/X at DOS prompt
reboot
Datavue
Ctrl-Shift-M
Ctrl-Shift-M
DEC**
Dell**
Digital*
FN-F5
FN-F5
FN-F4
FN-F4
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-F8
FN-D
FN-D
FN-F12
FN-F12
automatic
reboot
FN-F2
FN-F2
Dolch
dip switch to CRT
dip switch to LCD
Epson
dip switch to CRT
dip switch to LCD
Everex*
setup screen option
setup screen option
For-A
Ctrl-Alt-Shift-C
Ctrl-Shift-Alt-L
Fujitsu
FN-F10
49
Downloaded from ProjectorsManual.com Manuals
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Gateway
FN-F3
FN-F1/FN-F1 again simultaneous
FN-F3
FN-F1
Grid* **
FN-F2, choose auto or
simultaneous
FN-F2
Ctrl-Alt-Tab
Ctrl-Alt-Tab
Hitachi
FN-F7
FN-F7
Honeywell
FN-F10
FN-F10
Hyundai
setup screen option
setup screen option
IBM 970*
automatic
warm reboot
IBM ThinkPad**
reboot, enter setup menu
FN-F2
Computer
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor plugged
in
unplug monitor
Kris Tech
FN-F8
FN-F8
Leading Edge
FN-T
FN-T
Mac Portable
100
no video port: not compatible
Mac PowerBook
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165, 180,
520, 540, 5300
Control Panel folder, PowerBook Display folder;
Activate Video Mirroring
210, 230, 250,
270, 280, 2300
requires Apple Docking Station or Mini Dock
Magitronic
FN-F4
FN-F4
Mastersport
FN-F2
FN-F1
50
Downloaded from ProjectorsManual.com Manuals
warm reboot
Computer
Key command to
activate port
Key command to
de-activate port
Micro Express*
automatic
warm reboot
Micron
FN-F2
FN-F2
Microslate*
automatic
warm reboot
Mitsubishi
SW2 On-Off-Off-Off
SW2 Off-On-On-On
NCR
setup screen option
setup screen option
NEC* **
setup screen option
setup screen option
CRT at the DOS prompt
LCD at the DOS prompt
FN-F3
FN-F3
automatic
automatic
FN-O/*
FN-O/*
FN-F0
FN-F0
Ctrl-Alt-<
Ctrl-Alt->
Panasonic
FN-F2
FN-F2
Prostar
Ctrl-Alt-S at bootup
Ctrl-Alt-S at bootup
Olivetti*
Packard Bell* **
Samsung*
setup screen option
setup screen option
Sanyo
setup screen option
setup screen option
Sharp
dip switch to CRT
dip switch to LCD
Sun SPARCDataview
Ctrl-Shift-M
Ctrl-Shift-M
Tandy**
Ctrl-Alt-Insert
Ctrl-Alt-Insert
setup screen option
setup screen option
Tangent
FN-F5
FN-F5
Texas Instruments*
setup screen option
setup screen option
Top-Link* **
setup screen option
setup screen option
FN-F6
FN-F6
Toshiba* **
Twinhead*
WinBook
Ctrl-Alt-End
Ctrl-Alt-Home
FN-End
FN-Home
FN-F5
FN-F5
setup screen option
setup screen option
FN-F7
FN-F7
FN-F5
FN-F5
Automatic
Automatic
Ctrl-Alt-F10
Ctrl-Alt-F10
51
Downloaded from ProjectorsManual.com Manuals
A
p
p
e
n
d
i
x
Computer
Key command to
activate port
Key command to
de-activate port
Wyse
software driven
software driven
Zenith**
FN-F10
FN-F10
FN-F2
FN-F2
FN-F1
FN-F1
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
Zeos**
* These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depending on the computer model.
52
Downloaded from ProjectorsManual.com Manuals
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer PowerBooks—see below) on, the projector displays the same information that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip, then click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as
the primary monitor.
4 Restart the PowerBook.
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and
Sound.
2 In the Resolution list, choose the SimulScan mode, then click
OK.
3 If this changes your display settings, a dialog box appears.
Click OK to confirm the change.
53
Downloaded from ProjectorsManual.com Manuals
A
p
p
e
n
d
i
x
Diagonal Image Size (inches)
Projected Image Size
NOTE: Use the graph and table
to help you determine projected
image sizes.
250
maximum image size
200
150
minimum image size
100
50
0
5
15
10
20
25
30
Distance to Screen (feet)
FIGURE 32
Projected image size
Table 1:
Range of distance to the screen for a given screen size
Distance to screen
Diagonal
Screen Size
(inches/m)
60/1.5
72/1.8
84/2.1
90/2.3
100/2.5
120/3.1
150/3.8
54
Downloaded from ProjectorsManual.com Manuals
Image Width
(inches/m)
48/1.2
58/1.5
67/1.7
72/1.8
80/2.0
96/2.4
120/3.1
Maximum
distance
(ft/m)
8.5/2.6
10.2/3.1
11.9/3.6
12.7/3.9
14.1/4.3
17.0/5.2
21.2/6.5
Minimum
Distance
(ft/m)
6.9/2.1
8.3/2.5
9.7/3.0
10.4/3.2
11.6/3.5
13.9/4.2
17.4/5.3
C
INDEX
cables
audio 9
A
composite video 10
accessories, ordering 46
computer cable 3, 8, 9
activation commands for laptop com-
ordering 46
puters 48
Add New Hardware Wizard 14
adjusting
power 46
S-video 10
cases, ordering 46
brightness 26
ceiling projection 34
color 27
centering the image 20, 31
color gain 32
cleaning the projection lens 37
contrast 27
Color Management menu options
height of the projector 20
keystone 26
Auto color gain 32
Degamma 32
tint 27
color, adjusting 27
volume 24
colors
Advanced menu options
Ceiling Project 34
Display Messages 34
Display Startup Screen 35
Low Power 34
don’t match monitor colors 43
not displayed 42
compatibility
IBM-compatible 2
Macintosh 2
Rear projection 34
component video 12
Reset 35
composite video 10
altitude limits 45
assistance. See Technical Support
audio cable, connecting 9
Audio menu options
computers
compatible 2
connecting 9
connecting
Mute 28
audio cable 9
Volume 28
computers 9
Auto color gain 32
power cord 14
auto image 30
remote 9
auto source 33
USB mouse 9
video device 10
B
connectivity, enhanced 12
brightness, adjusting 26
contrast, adjusting 27
buttons on keypad
Control menu options
Menu/select 22
Auto source 33
Power 23
Default Source 33
Source 22
Standby Time 33
Standby 24
Volume 24
55
Downloaded from ProjectorsManual.com Manuals
I
n
d
e
x
D
I
Default Source 33
IBM-compatible computers 2
Degamma 32
image
Display menu options
adjusting 14, 19
Blank screen 27
centering 31
Brightness 26
colors don’t match computer’s 43
Color 27
focusing 19
Contrast 27
fuzzy lines 30
Keystone 26
has lines or spots 43
Sharpness 27
not centered 42
Tint 27
not displayed 41
Display Messages 34
out of focus 42
Display Startup Screen 35
quality 42–43
displaying on-screen menus 22
resolution 1
drivers, installing 14
reversed 34, 42
size 7, 54
E
streaked 43
elevator button/foot 20
too wide or too narrow 42
enhanced connectivity module 12
zooming 19
Image menu options
F
Auto Image 30
focusing the image 19
Horiz. Position 31
forward/back buttons 23
Manual Sync 30
fuzzy lines 30
Manual Tracking 30
Overscan 31
H
Resize 29
HDTV 2, 10, 27
Vert. Position 31
height adjustment 20
Video Standard 31
Zoom 30
installing drivers 14
K
keypad 22
keystone adjustment 23
56
Downloaded from ProjectorsManual.com Manuals
L
P
lamp
PAL video 31
ordering 46, 47
Power button 14, 23
replacing 37
power cord
turns off unexpectedly 43
connecting 14
lamp hour counter 36, 37, 39
ordering 46
Language menu 35
power up sequence 17, 41
language, selecting for menus 35
PowerPoint slides, advancing with the
laptop computers
activation sequence to allow
secondary display 48
remote 9, 23
project from behind the screen 34
project from the ceiling 34
compatibility 9
connecting 9
R
LED 22, 24
rear projection 34
lens
remote control
advancing PowerPoint slides
cap 46
with 9, 23
cleaning 37
connecting 9
low power mode 34
controlling the computer with 9
replacing the batteries 40
M
M1-DA analog computer cable 3, 8
Macintosh computers
compatibility 2
using 21, 22
replacing projection lamp module 37
re-positioning the image on the screen
installing drivers 16
31
menus. See on-screen menus
resetting adjustments 35
monitor loop-through 12
resetting the lamp hour counter 39
monitor, projected colors don’t match
resizing the image 29
43
mouse buttons 22
resolution 1
RS-232 control 13
mouse, connecting 9
mute 28
S
safety guidelines iii
N
security lock 40, 47
NTSC video 31
sharpness 27
SimulScan, using with PowerBooks 53
O
Source button 22
on-screen menus
specifications 45
changing language of 35
standby 17, 24
displaying 25
standby time 33
overscan 31
Status menu 36
S-video, connecting 10
57
Downloaded from ProjectorsManual.com Manuals
I
n
d
e
x
T
Technical Support
information to have on hand
before you call 44
temperature limits 45
test pattern 41
text not visible 42
tint, adjusting 27
troubleshooting 41
turning off the projector 17
turning on the projector 14
U
USB mouse
connecting 9
installing drivers 14
V
vertical lines displayed 30, 43
VESA connector 12
video mirroring on a PowerBook 53
video resize 31
video standards 31
Volume buttons 24
volume, adjusting 24
W
widescreen video 29
Z
Zoom mode 24
zooming the image 19, 24, 30
58
Downloaded from ProjectorsManual.com Manuals
LIMITED WARRANTY
BOXLIGHT Corporation (“BOXLIGHT”) warrants that each CD-600m and CD-750m (“the Product”) sold hereunder will conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to
the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or
resale. Said warranty shall continue for a period of two (2) years from the date of such purchase. The standard limited warranty excludes the lamps in projectors after 120 days and the accessories after one year. BOXLIGHT does not warrant that the
Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business
use. BOXLIGHT’s liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replacement Product may be re-furbished in
“like-new” condition, at BOXLIGHT’s sole discretion. To exercise the Purchaser’s rights under the foregoing warranty, the
Product must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any authorized BOXLIGHT service center provided, and the Product must be accompanied by a written letter explaining the problem and which includes (i) proof
of date of purchase; (ii) the dealer ’s name; and (iii) the model and serial number of the Product. When sending your unit in
for repair, please ship your unit in its original packing material or a B OXLIGHT approved ATA Shipping Case, or have a professional packaging company pack the unit. Please insure your shipment for its full value. A return authorization number,
issued by the BOXLIGHT customer service department, must also be clearly displayed on the outside of the shipping carton
containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations,
or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or failure to properly use
the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO
YOU.
Downloaded from ProjectorsManual.com Manuals
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER
ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF
THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR
LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT’S LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT
MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
Part Number 010-0291-00
Downloaded from ProjectorsManual.com Manuals