PLANET POE-173 User's manual
Add to My manuals2 Pages
Planet POE-173 is a Single-Port 10/100/1000Mbps Ultra Power over Ethernet (PoE) Injector capable of delivering up to 60 watts of power over Ethernet cables. It supports IEEE 802.3at/af PoE standard and is backward compatible with IEEE 802.3af PoE devices. The POE-173 can be used to power various PoE-enabled devices such as IP phones, network cameras, and wireless access points. It features auto-detection of PoE IEEE 802.3at/af equipment and devices, remote power feeding up to 100 meters, and LED indicators for Power and PoE port status.
advertisement
1. Package Contents
Thank you for purchasing PLANET Single-Port
10/100/1000Mbps Ultra PoE Injector, POE-173.
Model LAN Port Speed PoE Standard
PoE
Budget
POE-173 10/100/1000Mbps
Ultra PoE, backward compatible with
IEEE 802.3at/af standard
60 watts
The term “Ultra PoE Injector” in the following section of this User’s Manual means the POE-173.
The box of the Single-Port 10/100/1000Mbps Ultra
PoE Injector should contain the following items:
The Single-Port 10/100/1000Mbps Ultra PoE
Injector x 1
User’s Manual x 1
AC Power Cord x 1
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
- 1 -
Note
PD (Powered Device) such as IP phones, network cameras or wireless access points is a PoE-enabled terminal by PSE and thus it consumes energy.
3. Product Specifications
Product
Hardware Specifications
LAN
Interface
PoE
POE-173
1 x RJ45 STP, “Data” Input Port
1 x RJ45 STP, “Data + Power”
Output Port
AC
Connector
Ultra PoE
(60W)
1 x AC input power socket,
IEC-320 C6
4-pair UTP Cat. 5, 5e, 6 up to
100m (328ft)
Network
Cable
802.3af / at
PoE (15W /
30W)
2-pair UTP Cat. 3, 4, 5, up to
100m (328ft)
LED Indicator
System: Power x 1 (Green)
PoE Port: Active, PoE ready /
In Use x 1 (Green)
10/100/1000Mbps Data Rate
Dimensions
(W x D x H)
Weight
Unit Output Voltage
115 x 62.5 x 31 mm
177g
DC 50V, 1.2A
- 3 -
4. Product Outlook
Figure 1: An overview of Ultra PoE Injector.
Figure 1: POE-173 Outlook
LED Indicators
LED Color
POWER Green
ACTIVE Green
Function
It indicates that the Ultra PoE Injector has power.
It indicates the port is providing 50V DC in-line power.
- 5 -
2. Product Features
Interface
1-Port Data input
1 x AC 100-240V input power socket
Power over Ethernet
Ultra Power over Ethernet PSE
Up to 60 watts of power on 4-pair UTP cable
Backward compatible with IEEE 802.3at/af PD device
Auto-detection of PoE IEEE 802.3at/af equipment and devices to check whether there’s any damage done via incorrect installation
Remote power feeding up to 100m
Hardware
All-in-one compact size design
Internal power supply
LED indicators for Power LED and Active LED
(PoE ready / In-use)
Note
PSE (Power Sourcing Equipment) is a device (switch, or hub for instance) that will provide power in a PoE setup.
The maximum allowed continuous output power per such device in IEEE 802.3af is
15.4 watts, in IEEE 802.3at is 30 watts and Ultra PoE is 60 watts.
- 2 -
Power Requirements
100-240V AC @50/60Hz,
1.5A max.
Power Consumption 60 watts max.
Operating Temperature 0 ~ 50 degrees C
Storage Temperature -10 ~ 70 degrees C
Operating Humidity
5 ~ 95%, Relative Humidity, non-condensing
Storage Humidity
5 ~ 95%, Relative Humidity, non-condensing
Power over Ethernet
PoE Standard
Ultra PoE over 4-pairs UTP cable,
IEEE 802.3at High Power over
Ethernet End-Span / Mid-Span
PSE
PoE Power Supply Type End-Span + Mid-Span
PoE Power Output
DC 50V / 60-watt PoE via 4-pairs
DC 50V / 30-watt PoE via 2-pairs
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T
Gigabit Ethernet
IEEE 802.3at Power over
Ethernet Plus
IEEE 802.3af Power over Ethernet
Regulation Compliance FCC Part 15 Class B, CE
- 4 -
Note
Note
The Ultra PoE Injector and POE-171S can be installed in pair. However, the use of the third-party device is allowed if the device complies with
IEEE 802.3at Power over Ethernet Plus and a maximum of 30 watts of output capability.
Since the ultra PoE injector PoE port supports 50V DC PoE power output, please check and assure the Powered
Device’s (PD) acceptable DC power range is 50V DC; otherwise, it will damage the Powered Device (PD).
Ultra PoE Injector Installation
Due to the backward capability of IEEE 802.3at/ af PoE standard, the Ultra PoE Injector can directly connect with any IEEE 802.3at/af end-nodes such as PTZ (Pan, Tilt & Zoom) speed dome network cameras, color touch-screen voice over IP (VoIP) telephones, and multi-channel wireless LAN access points. The screen in Figure 2 is shown below.
- 7 -
5. Hardware Installation
The following section describes the hardware features of Ultra PoE Injector. Before connecting any network device to the Ultra PoE Injector, read this chapter carefully.
5-1. Before Installation
The POE-173 is backward compatible with IEEE
802.3af PoE and IEEE 802.3at high power PoE standard. It is equipped with an AC power cord with
100-240V AC input and injects DC 50V power into the pin of the twisted pair cable (pair 1/2 [+], 3/6
[-] and pair 4/5[+], 7/8[-]) for 60-watt Ultra PoE injection.
Before connecting the POE-173 to your powered device (PD), please check to ensure that your powered device (PD) can accept 60-watt PoE power through pin 1/2 (+) & 3/6 (-) and pin 4/5 (+) & 7/8
(-). Otherwise, it will damage your powered device
(PD).
Please also note: DO NOT connect POE-173 POE port to your non-POE network equipment Ethernet interface. Otherwise, it will damage your network equipment.
If there is difficulty in finding a power socket for
AC-DC Adapter of your non-PoE network device, the
Ultra PoE Injector and POE-171S (Ultra PoE Splitter) can provide you with DC power for this Ethernet device conveniently and easily.
- 6 -
100 meters
Switch
Data
AC
Power
POE-173
Ultra PoE Injector
Data
PoE
Power
PoE PTZ
IP Camera
AC
PoE
1000BASE-T UTP
1000BASE-T UTP with PoE
Power Line (AC)
Figure 2: Connection to IEEE 802.3at / 802.3af Powered
Devices
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on steadily.
2. Connect a standard network cable from Switch / workstation to “LAN” port of Ultra PoE Injector.
3. Connect the long cable to the port (PoE) of the remote PoE PD device.
4. Connect with IEEE 802.3at/af devices.
Once Ultra PoE Injector detects the existence of an IEEE 802.3at / 802.3af device, the ACTIVE LED indicator will be on steadily to show it is providing power.
- 8 -
Note
If the connected device is not fully complying with IEEE 802.3at / 802.3af
Power over Ethernet or in-line power device, the LED indicator of Ultra PoE
Injector will not be on steadily.
The Ultra PoE Injector and Splitter Installation
Below are steps showing how to install the PLANET
Ultra PoE Injector (POE-173) and Ultra PoE Splitter
(POE-171S) in pair.
100 meters
Switch
Data Data
AC
Power
POE-173
Ultra PoE Injector
PoE
Power Data
POE-171S
Ultra PoE
Splitter
DC
Power
Power 12V/19V/24V
Laptop
PoE
1000BASE-T UTP
1000BASE-T UTP with PoE
AC
DC
Power Line (AC)
Power Line (DC)
Figure 3: Topology of the Connection of POE-173 and
POE-171S
- 9 -
The Ultra PoE Injector and PoE Extender
Installation
Below are steps showing how to install the PLANET
Ultra PoE Injector (POE-173) and 802.3at PoE+
Extender (POE-E201) to extend the distance of networking.
Data
Power
POE-173
Data + Power
PoE
100 meters
802.3at
PoE Extender
200 meters
Data + Power
PoE
100 meters
PoE IP Camera
PoE
1000BASE-T UTP
1000BASE-T UTP with PoE
AC
Power Line (AC)
Figure 4: Topology of the Connection of POE-173 and
POE-E201
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on steadily.
2. Connect a standard network cable from “POE” port of Ultra PoE Injector to the “IN” port of
POE-E201.
3. The Ultra PoE Injector delivers both Ethernet Data and PoE power over UTP cable to the POE-E201 and the “ACTIVE” LED of Ultra PoE Injector and
“PoE IN” LED of POE-E201 will light up continuously.
- 11 -
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on steadily.
2. Connect a standard network cable from “POE” port of Ultra PoE Injector to “PoE In” port of
POE-171S. The “ACTIVE” LED of Ultra PoE
Injector and POE In-use LED of POE-171S will light up continuously.
3. Connect a standard network cable from Switch / workstation to “LAN” port of Ultra PoE Injector.
“Ethernet” port of POE-171S to the RJ45 port of remote device.
5. Adjust proper DC power output and connect DC plug from “DC OUT” of POE-171S to remote device.
6. Power on the remote device and its power LED indicator will remain on.
Note
Please make sure the POE-171S output voltage is correct before applying power to remote device. The POE-171S provides DC12V/19V/24V power output.
4. Connect the additional standard network cable to the remote Powered Device (PD) via the
“OUT” port of POE-E201.
5. The “OUT” port is also the power injectors which transmits DC voltage to the standard network cable and transfer data and power simultaneously between the Ultra PoE Injector and PD.
6. Once POE-E201 detects the existence of an IEEE
802.3at / 802.3af device, the “PoE OUT” LED indicator will be on steadily to show it is providing power.
Note
1. If the connected device is not fully complying with IEEE 802.3at /
802.3af standard or in-line power device, the PoE OUT LED indicator of
POE-E201 will not be on steadily.
2. According to IEEE 802.3at / 802.3af standard, the POE-E201 will not inject power to the cable if not connected to a standard IEEE 802.3at / 802.3af device.
- 10 - 12 -
Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET
Web site first to check if it could solve your issue. If you need more support information, please contact
PLANET switch support team.
PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address : [email protected]
Copyright © PLANET Technology Corp. 2015
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 13 -
EC Declaration of Conformity
For the following equipment:
*Type of Product : Single-Port 10/100/1000Mbps Ultra PoE Injector (60 Watts)
*Model Number : POE-173
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.). is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022
EN 61000-3-2
EN 61000-3-3
EN55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(2006 + A1:2007 + A2:2010)
(2006 + A1:2009 + A2:2009)
(2008)
(2010)
(2008)
(2006+A1: 2007 + A2:2010)
(2004 + A1:2010)
(2005)
(2008)
(2009)
(2004)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan
Place
24 th May, 2013
Date Legal Signature
PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
advertisement