Daniel Ultrasonic Flow Meter - 3410/3810 Series Local Display Field Install Kit
Add to my manuals
18 Pages
advertisement
Quick Install Guide
3-9000-780 Rev A
September 2014
3410/3810 Series Local Display Field Install Kit
Local Display Field Install Kit
September 2014
Daniel customer service
Quick Install Guide
3-9000-780 Rev A
Location
North America/Latin America
Daniel Customer Service
USA (toll free)
Asia Pacific (Republic of Singapore)
Europe (Sterling Scotland, UK)
Middle East Africa (Dubai, UAE)
•
Customer Service:
• Customer Support:
• Asia-Pacific:
• Europe:
Telephone number
+1.713.467.6000
+1.713.827.6413
+1.888.356.9001
+65.6777.8211
+44 (0)1786.433400
+971 4 8118100
Fax number
+1.713.827.4805
+1.713.827.6312
+1.713.827.3380
+65.6777.0947.0743
+44 (0)1786.433401
+971 4 8865465
[email protected] [email protected] [email protected]
Return Material Authorization (RMA)
A Return Material Authorization (RMA) number must be obtained prior to returning any equipment for any reason.
Download the RMA form from the Support Services web page by selecting the link below. www2.emersonprocess.com/EN-US/BRANDS/DANIEL/SUPPORT-SERVICES/Pages/Support-Services.aspx?
3
Local Display Install Kit
Local Display Field Install Kit
September 2014
Signal words and symbols
Pay special attention to the following signal words, safety alert symbols and statements:
Quick Install Guide
3-9000-780 Rev A
This is a safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Danger indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Warning indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Caution indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Notice is used to address safety messages or practices not related to personal injury.
Important
Important is a statement the user needs to know and consider.
Tip
Tip provides information or suggestions for improved efficiency or best results.
Note
Note is a “general by-the-way” content not essential to the main flow of information.
4
Local Display Install Kit
Local Display Field Install Kit
September 2014
Component disassembly
Quick Install Guide
3-9000-780 Rev A
1. Local Display Field Install Kit Includes.
5 4
8
2 1
3
• Preassembled assemblies and parts:
-
LCD Display Board, Shroud, LCD Module
-
Cover – Housing (glass end cap) with O-Ring
-
Backplane board
-
Pan HD Screws #6-32 X .88
2. Local Display Field Install Kit Parts List.
ITEM * QTY DESCRIPTION
5
6
7
1
2
3
4
1
1
1
1
1
2
1
Preassembled:
LCD Display Field Install Kit
•
LCD Display Board
•
LCD Display Shroud
•
Pan HD Screw PH SEMS #6-32 X .38 M/S W/410 EXT 18-8 SST
•
LCD Module
Preassembled:
Cover – HSG LCD Type FB100
•
O-Ring #2-245
Backplane Board 3410/3810
8 4 Pan HD Screw PH SEMS #6-32 X .88
*
Note:
Item numbers correlate with DMC-009079 - 3410/3810 Series LCD Module
Local Display Install Kit
5
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
3. Check firmware version before powering off the meter.
Application options:
•
Daniel MeterLink™
•
AMS® Device Manager
•
Field Communicator
•
Requirements: Firmware Version 1.06 and Uboot Version January 31, 2013 or later.
•
If necessary to upgrade firmware,
-
Open Daniel MeterLink and connect to the meter.
-
Open an Internet browser.
-
Navigate to the Daniel website:
www.Daniel.com
.
-
Use Quick Links and click MeterLink Registration and Download to access the latest firmware.
Local Display Install Kit
-
Go to Daniel MeterLink and use the Tools|Program Download menu to download a file to the meter. Click Open to display an Open Download File dialog. Select the desired file and click Open. Daniel MeterLink™ only downloads components that are different than what is currently installed in the meter.
6
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
CPU
TB-2
4. Remove power to the equipment and remove transmitter electronics enclosure endcaps.
•
Remove endcap security seals, if installed, and security latches.
•
Remove power from equipment before removing endcaps if possible and/or ensure explosive atmosphere is not present before opening the transmitter electronics enclosure.
•
Unplug CPU Module terminal board connectors (TB-1 and TB-2).
•
Unplug I/O Module, and Power Supply terminal board connectors.
•
Pull the CPU and I/O Modules from the enclosure.
24V Loop
Power
10.4VDC - 36VDC
Power
CPU
TB-1
I/O Module
Connectors
Local Display Install Kit
7
Local Display Field Install Kit
September 2014
5. Remove the Backplane board.
Backplane
Board
•
Remove four screws with lock washers.
•
Pull Backplane from housing.
•
Remove Power Supply and I.S. Barrier boards from Backplane.
6. Disconnect the Acquisition cable.
Acquisition
Cable
Quick Install Guide
3-9000-780 Rev A
I.S. Barrier
Board
Power Supply
Board
7. Components disassembly complete.
Local Display Install Kit
8
Local Display Field Install Kit
September 2014
Component assembly
Quick Install Guide
3-9000-780 Rev A
1. Backplane Board with 14 pin connector.
14 Pin
Connector
Backplane
Board
Note:
Check existing 3410/3810 Series Backplane board (P/N 1-360-03-007) Rev D minimum for 14 pin connector (J8).
If equipped, use this board. If not, use board included with the Local Display Field
Install Kit.
Acquisition
Cable
•
Attach Acquisition cable to Backplane.
•
Tighten connector screws.
Local Display Install Kit
9
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
2. Plug Power Supply Board and I.S. Barrier Module onto Backplane
Board with 14 pin connector.
I.S. Barrier Board
Backplane Board
Power Supply Board
3. Plug Local Display Board into the Backplane 14 Pin connector.
14 Pin Connector
Local Display Board
•
Make sure LCD Board is fully seated to Backplane 14 pin connector.
Local Display Install Kit
10
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
4. Slide Backplane, Power Supply, I.S. Barrier Module and Local
Display Module assembly into transmitter enclosure and fasten with 4 Pan Head screws.
•
Make sure boards are aligned in the enclosure and I.S. Barrier Board is inside the guide plate key retainer.
•
Use the long Pan HD Screws #6-32 X .88 provided with the kit.
5. Install endcap with sight glass.
•
Make sure endcap O-ring is installed.
Local Display Install Kit
11
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
6. Reinstall CPU Module and I/O Module in the enclosure.
7. Install CPU Module TB-1 and TB-2 and I/O Module terminal connectors.
CPU
TB-2
CPU
TB-1
I/O Module
Connectors
Local Display Install Kit
12
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
8. If explosive atmosphere is not present, connect the Power
Supply terminal connectors and apply power to the unit.
24V Loop
Power
10.4VDC - 36VDC
Power
•
Ensure all CPU LEDs are green.
CPU LEDs
•
Observe Local Display startup sequence (see
Local Display Install Kit
13
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
9. If explosive atmosphere is present, install endcaps and apply site power to equipment.
Endcap security latch
•
Reinstall endcap security latches.
•
Apply site power.
Note:
If explosive atmosphere is present and site power initializes the unit, a Service technician should observe the Local Display startup sequence (see
10. Observe Local Display startup sequence.
Local Display
Startup sequence –
All segments displayed
•
2 seconds after power up, the “DANIEL” logo appears at the bottom of the LCD screen.
•
The Checksum displays.
•
Make sure all segments are displayed (all the segments will come on and stay on for about 4 seconds). Pay careful attention and make sure that all segments are functioning and no segments are missing.
•
The Wait command displays, and then the four default Display Items scroll on the display.
Local Display Install Kit
14
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
11. Configure display items, measurement units and scroll delay.
Configuration applications options:
•
Daniel MeterLink™ - Field Setup Wizard (see image above)
•
•
AMS® Device Manager
•
Reference manuals:
(
AMS Suite: Intelligent Device Manager
Field Communicator
(
Field Communicator
)
)
-
3-9000-761 Rev 4 HART® Field Device Specification 3410 Series Gas Ultrasonic Meters
-
3-9000-762 Rev 4 HART® Field Device Specification 3810 Series Liquid Ultrasonic Meters
-
3-9000-759 Rev D 3410 Series Gas Ultrasonic Meters Installation Manual
-
3-9000-760 Rev C 3810 Series Liquid Ultrasonic Meters Installation Manual
-
3-9000-765 Rev C 3812 Liquid Ultrasonic Meters Installation Manual
12. Reinstall wire security seals on the endcaps, if necessary.
13. Installation complete.
3410/3810 Series
Transmitter with Local
Display
Local Display Install Kit
15
Local Display Field Install Kit
September 2014
Quick Install Guide
3-9000-780 Rev A
Local Display Install Kit
16
P/N 3-9000-780
Rev A
2014
Daniel Measurement and Control, Inc.
11100 Brittmoore Park Drive
Houston, TX 77041 USA
T+1 713-467-6000
F+1 713-827-4805
USA Toll Free 1 888-356-9001
Daniel Measurement Services, Inc.
T +1 713-827-6413
www.Daniel.com
Europe: Sterling, Scotland, UK
T + 44-1786-433400
Middle East: Africa: Dubai, UAE
T +971-4-811-8100
Asia Pacific: Singapore
T +65-677-8211
This product is a core component of the PlantWeb® digital plant architecture.
© 2014 Daniel Measurement and Control, Inc., All rights reserved
The Emerson logo is a trademark and service mark of Emerson Electric Co. Daniel
Measurement and Control, Inc. (Daniel) are Emerson Process Management business units.
The Daniel name and logo are trademarks of Daniel Industries, Inc. The Senior, Junior,
Simplex, MeterLink SeniorSonic, JuniorSonic, and DanPac are trademarks of Daniel
Industries, Inc. All other trademarks are property of their respective owners.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement