D.A.S. H-4000, H-1500, H Serie, H-2200, H-3000 User's manual

Manual de Usuario / User’s Manual
H series
H
H series
Amplificadores de Potencia / Power Amplifiers
Keep these instructions.
Heed all warnings. Follow all instructions.
The exclamation point inside an equilateral triangle indicates the
existence of internal components whose substitution may affect
safety.
Aparato de Clase I.
Class I device.
The lightning and arrowhead symbol warns about the presence
of uninsulated dangerous voltage. To reduce the risk of electric
shock, do not remove the cover.
The lightning and arrowhead symbol near the output terminals of
the amplifier alert of the risk of electric shock in normal
conditions of use (terminal dangerous to the tact). Do not touch
these terminals while the amplifier is working.
The connected outer wiring to these terminals requires of its
installation by an instructed person and the use of a flexible the
cable already prepared.
This symbol on the product indicates that this product should
not be treated as household waste. Instead it shall be handed
over to the appicable collection point for the recycling of
electrical and electronic equipment.
The ON position is indicated in the switch by means of the
corresponding standardized symbols (IEC 60417-1:1998 and
IEC 60417-2:1998) and a red LED located near the switch.
If the apparatus is connected permanently, the electrical system
of the building must incorporate a multipolar switch with a
separation of contact of at least 3mm in each pole.
Do not expose this device to rain or moisture. Do not use this
apparatus near water (for example, swimming pools and
fountains). Do not place any objects containing liquids, such as
bottles or glasses, on the top of the unit. Do not splash liquids
on the unit. IP-20 equipment.
Clean only with a dry cloth. Do not use any solvent based
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
The circulation of air on the fan inlet grills must not be blocked.
The air stream circulates from back to front.
Working temperature ranges from 15ºC to 35ºC with a relative
humidity of 75%.
Unplug this apparatus during ligtning storms, earthquakes or
when unused for long periods of time.
Take into account that the nominal AC voltage is the value shown
in the equipment ±10% (according to IEC 60065:2001).
If the cable or the mains plug are damaged they must be
replaced. Contact the manufacturer to provide you with the
necessary spare parts.
No user serviceable parts inside. Refer all servicing to qualified
service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
WARRANTY
All D.A.S. products are warrantied against any manufacturing defect
for a period of 2 years from date of purchase.
The warranty excludes damage from incorrect use of the product.
All warranty repairs must be exclusively undertaken by the factory
or any of its authorised service centers.
To claim a warranty repair, do not open or intend to repair the
product.
Return the damaged unit, at shippers risk and freight prepaid, to
the nearest service center with a copy of the purchase invoice.
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
2006/95/CE
l
2004/108/CE
l
Directiva RoHS
2002/95/CE
l
Directiva RAEE (WEEE)
2002/96/CE
Y es conforme a las siguientes Normas Armonizadas Europeas:
In accordance with Harmonized European Norms:
l
EN 60065:2002
l
EN 55103-1:1996 Electromagnetic compatibility.
Product family standard for audio, video, audiovisual and entertainment lighting control apparatus
for professional use. Part 1:Emission.
l
EN 55103-2:1996 Electromagnetic compatibility.
Product family standard for audio, video, audiovisual and entertainment lighting control apparatus
for professional use. Part 2:Immunity.
Audio, video and similar electronic
apparatus. Safety requirements.
•
•
DESCRIPCIÓN DEL PANEL FRONTAL
B) INDICADORES LED DE ENCENDIDO DEL AMPLIFICADOR
Serie H / H series
Manual del usuario / User's manual
3
DESCRIPCIÓN DEL PANEL POSTERIOR
Serie H / H series
Manual del usuario / User's manual
4
USO
ENCENDIDO / APAGADO
model
H-1500
H-2200
H-4000
INDICADOR LED DE RECORTE (CLIP)
Carga /
model
load
Output Power
Max
1/3
1/8
BTU/h
Kcal/h
BTU/h
Kcal/h
BTU/h
idle
Kcal/h
BTU/h
Kcal/h
H-1500
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
2960
4725
3350
745
1190
845
1720
3170
2665
435
800
670
740
1295
1105
185
325
280
235
235
235
60
60
60
H-2200
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
4555
6835
4285
1150
1720
1080
2565
4865
4065
645
1225
1025
1195
2025
1710
300
510
430
470
470
470
120
120
120
H-4000
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
6495
10880
6120
1635
2740
1540
3345
6015
4445
845
1515
1120
1435
3940
3345
360
995
845
470
470
470
120
120
120
Serie H / H series
Manual del usuario / User's manual
5
Serie H / H series
Manual del usuario / User's manual
6
H-2200
H-4000
280 W
450 W
750 W
900 W
1500 W
500 W
850 W
750 W
1400 W
1100 W
2000 W
1500 W
2800W
2200 W
4000 W
<0.05%
0.02%
0.02%
0.03%
45 V/us
56V/us
65V/us
20Hz – 20kHz +0/-0.5dB, 5Hz – 48kHz –3dB
>310
1V/1.3V
1.34V/1.5V
1.84V/1.96V
32 dB (40x)
10K Ohm no bal./unbal., 20K Ohm bal.
Clase H / Class H
14 Kg (31 lbs.)
15 Kg (33 lbs.)
30 Kg (65 lbs.)
Véase sección Dibujos de línea / See Line Drawings section
DIBUJOS DE LÍNEA
Serie H / H series
Manual del usuario / User's manual
7
Serie H / H series
Manual del usuario / User's manual
8
Serie H / H series
9
LONGITUD /
LENGTH
CALIBRE
AWG (Nr.)
AREA
R (ohm)
PÉRDIDA DE POTENCIA /
POWER LOSS
FACTOR DE
AMORTIGUAMIENTO /
DAMPING FACTOR
8 ohm
4 ohm
8 ohm
4 ohm
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.103
0.066
0.041
0.026
0.016
0.010
1,3 %
0,8 %
0,5 %
0,3 %
0,2 %
0,1 %
2,6 %
1,7 %
1,0 %
0,7 %
0,4 %
0,3 %
61
85
115
147
179
207
30
42
57
73
90
104
5 m (16.4 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.207
0.131
0.082
0.052
0.033
0.021
2,5 %
1,6 %
1,0 %
0,7 %
0,4 %
0,3 %
5,0 %
3,3 %
2,1 %
1,3 %
0,8 %
0,5 %
34
50
72
99
130
161
17
25
36
50
65
81
7,5 m (24.6 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.310
0.197
0.123
0.079
0.049
0.031
3,9 %
2,5 %
1,5 %
1,0 %
0,6 %
0,4 %
7,8 %
4,9 %
3,1 %
2,0 %
1,2 %
0,8 %
24
35
53
74
103
134
12
18
26
37
52
67
10 m (33 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.413
0.262
0.164
0.105
0.066
0.041
5,1 %
3,3 %
2,1 %
1,3 %
0,8 %
0,5 %
10,2 %
6,6 %
4,1 %
2,6 %
1,6 %
1,0 %
18
28
42
60
85
115
9
14
21
30
42
57
15 m (49 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.620
0.393
0.246
0.157
0.098
0.062
7,8 %
4,9 %
3,1 %
2,0 %
1,2 %
0,8 %
15,6 %
9,8 %
6,2 %
3,9 %
2,5 %
1,6 %
12
19
29
43
63
88
6
9
15
22
31
44
20 m (66 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.827
0.525
0.328
0.210
0.131
0.082
10,3 %
6,5 %
4,1 %
2,6 %
1,6 %
1,0 %
20,6 %
13,1 %
8,2 %
5,3 %
3,3 %
2,0 %
9
14
22
34
50
72
5
7
11
17
25
36
50 m (164 ft)
16
14
12
10
8
6
1.31 mm2
2.1 mm2
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.313
0.820
0.525
0.328
0.205
0.125
16.4 %
7.7 %
4.9 %
3.1 %
1.9 %
1.6 %
32.8 %
15.4 %
9.8 %
6.1 %
3.9 %
3.1 %
6
12
19
29
44
52
3
6
10
15
22
26
75 m (246 ft)
14
12
10
8
6
2.1 mm2
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.230
0.788
0.491
0.308
0.186
15.4 %
9.9 %
6.1 %
3.9 %
2.3 %
30.8 %
19.7 %
12.3 %
7.7 %
4.7 %
6
9
15
24
37
3
5
8
12
19
100 m (328 ft)
12
10
8
6
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.050
0.655
0.410
0.248
13.1 %
8.2 %
5.1 %
3.1 %
26.3 %
16.4 %
10.2 %
6.2 %
7
12
18
29
4
6
9
14
2,5 m (8.2 ft)
Serie H / H series
Manual del usuario / User's manual
10
A channel’s protection may be triggered by:
INTRODUCTION
•
Overheating sensed at any part of a channel. When the
amplifier has cooled down, the channel’s output will be
connected and operation will resume. The control circuit
has some degree of built-in hysterisis to avoid turn-on
and off oscillations.
•
Presence of DC at a channel’s output. Since it may
severely damage speakers, the amplifier will deactivate
the output in the event that DC levels are too high. If load
impedance is too low, the amplifier is also deactivated.
Once DC is no longer present, the PROTECTION LED will
turn off and output is reactivated.
•
Short-circuit at a channel’s output. Although this
protection is provided, it is dangerous that the amplifier
remains in this situation for a long time. In case of a
short-circuit, turn off the amplifier while examining any
equipment connected to the amplifier’s output, together
with the connections and cabling. In this case, once the
short circuit is gone the output is NOT reactivated, but
the amplifier needs to be switched off and on.
•
When the amplifier is switched on, the output is also
deactivated for a few seconds to prevent dangerous
transients from damaging the speakers, and the
PROTECTION LED is on until the amplifier is ready for use.
General
Thank you for purchasing a D.A.S. power amplifier. It has been
built with the most advanced modular technology, and has
been designed through the use of computer-aided design for
both the electronic and mechanical parts.
Features
•
•
•
•
•
•
•
•
•
•
Class H
Dual balanced XLR inputs
Binding post and Speakon output connections
Variable speed back-to-front fan cooling
Front located volume controls
Overload, short-circuit, DC and thermal protection
Each channel has separate circuitry, built onto a separate
power module, facilitating servicing in the event of a
breakdown
Stereo, parallel and mono operation modes
Clip limiters
Clip, protection and idle LED indicators
FRONT PANEL DESCRIPTION
A) POWER SWITCH
Turns the amplifier on (“|” position) and off (“0” position).
There is a turn-on delay, to ensure that all appropriate voltages
are properly adjusted. The switch is of an automatic thermalmagnetic type and switches off when the power supply
protection disables the mains supply.
B) POWER LED
When lit, this LED shows that the amplifier is on.
F) SIGNAL LED
This LED shows the presence of signal at the amplifier’s inputs
and is dependent on the position of the LEVEL control.
G) COOLING AIR OUTLET GRILLES
Fan cooling permits airflow through the most vital parts of the
amplifier. Since the airflow finds its way out through these
grilles, keep them as clean and dust-free as possible to assure
proper cooling.
C) INPUT LEVEL CONTROLS
Volume levels for each channel can be adjusted by using the
knobs found on the front panel. The effect is the same as
adjusting the gain of the amplifier. Gain is maximum when the
LEVEL rotary potentiometer is rotated fully clockwise.
D) CLIP LED
In the event that the signal’s excursion exceeds the maximum
voltage from the power supply, the unit will indicate saturation
through the clip LED of the channel involved.
E) PROTECTION LED
When a channel’s output is disconnected by the amplifier’s
protection, this LED is on.
Serie H / H series
11
BACK PANEL DESCRIPTION
your region, cable colour codes are brown (live), blue (neutral)
and yellow-green (earth).
A) OUTPUT CONNECTIONS
E) FAN INLET GRILLES
Like for the front outlet grilles, keep clean and dust-free to
assure free air intake for proper cooling.
For connection of channel outputs to speakers, both binding
posts and Speakon NL4 connections are provided.
For the binding posts, polarity is clearly indicated by black (–)
and red (+) output terminals.
INSTALLATION
Racking
For the Speakon situated on the right, pin assignments are:
Channel A : +1 / -1
Channel B : +2 / -2
Bridge : +1 / +2
For the Speakon situated on the left, pin assignments are:
Channel B : +1 / -1
Thus you may choose to connect both channels using only
one or the two Speakon connectors, depending on your needs.
B) INPUTS
An XLR input is connected in parallel to an XLR output.
Nominal input impedance is 20k ohm for balanced use and
10k ohm for unbalanced use.
Polarity complies with AES14-1992 (ANSI S4.48-1992) and
therefore pin assignments are:
1 = GND (Ground)
2 = (+) non-inverted signal
3 = (–) inverted signal
C) INPUT MODE
This switch allows the selection for the input configuration
mode: stereo, parallel or bridge.
All amplifiers are 2U DIN high (except for H-4000, 3U),
standard 19-inch rack mount width.
Four front-panel mounting holes are provided for use with M5
or M6 or 1/4” screws. To avoid bending of the chassis in rack
mounting applications where the rack will be transported,
mount the amplifiers to the back of the rack using the rear
mounting holes. Alternatively, place the bottom amplifier
against the base of the rack and pile the amplifiers with no
clearance in between.
Amplifiers’ dimensions can be found on the “Line Drawings”
section of this manual.
Cooling
A fan cools the aluminium heat sinks and transformer from
back to front.
When mounting the unit onto a 19-inch rack, a rack cooling
system is not required, since the air is exhausted out through
the front grille. However, the rack must not be sealed, and it
should at least have a large enough ventilation grille to allow
air into the rack.
The fan speed is variable.
Typically the amplifiers are used in stereo mode, where the
input to channel A feeds channel A and the input to channel B
feeds channel B.
Parallel mode allows feeding both channels with the signal
plugged into channel A. Channel B's input is disconnected in
this mode.
Bridge mode allows easy wiring of an amplifier in mono mode.
The input to channel A feeds both channels with appropriate
polarity. Refer to the “Bridge Mode Operation” Appendix for
further information.
D) MAINS LEAD
The mains lead is terminated on a plug that will change
according to the amplifier’s mains voltage and area location.
If you need to cut off the plug to replace it for the type used in
Serie H / H series
Input cable connections
The Input Cabling Appendix shows balanced and unbalanced
connection from different types of connector to the amplifiers.
Speaker cable connections
Either the binding posts or the Speakon connectors can be
used.
Switch off the amplifier and unplug the unit from the socket
before making any connections.
The binding posts can be used with bare wire or banana
connectors. In either case, ensure that you remove the
required length of cable sleeve that allows for the conductor
itself to be hidden. Always note polarity (red=+, black=–).
Manual del usuario / User's manual
12
Use the table below to predict the heat emission from your
amplifier, which can be useful to evaluate air conditioning
requirements. They are given in BTU (British Thermal Unit) and
calories.
Speakon connectors offer quick connection for portable
applications. To enable a Speakon connection, plug the male
connector into the outlet and rotate it clockwise. It will then
lock into place and be ready for use.
The Appendices of this manual include a table to aid in the
selection of the appropriate cable gauge.
USE
SWITCH ON/OFF
Connection to mains
Switch your sound system on from back to front. Thus, switch
on the amplifiers last on your sound system. Switch sound
sources (CDs, turntables) first, then your mixer, then your
processors and crossovers and finally the amplifiers. If you
have more than one amplifier, switch them on sequentially,
one at a time or use a sequencer.
Nominal AC voltage is 230V. Export versions may operate at
115 V AC. Nominal AC voltage will always be indicated on the
back panel.
For electrical safety, the amplifier uses an automatic power
switch that will switch off in the event of overloading or
overheating of the power supply.
Follow the reverse order when switching off, and switch off
the amplifiers before any other element on your sound system.
Current draw
CLIP LED
Can be seen on the accompanying table for 230V. Double the
ratings for 115V.
The clip LED should never be on continuously. This will distort
the signal and may damage the speakers. In fact, severe
clipping is an easy way of burning a speaker’s voice coil.
International safety agencies specify AC consumption using
pink noise at 1/8th of maximum power. This is done to
represent the current requirements to reproduce a typical
musical programme. The 1/3rd power rating represents a
worst-case scenario, while the maximum draw represents
consumption with sine wave signal, which will never occur in
practice.
The amplifiers feature an automatic limiting system that
impedes prolonged saturation, but the dynamic nature of
music signals stops it from being a brick wall protection. Thus
at most, the clip light could be lit occasionally.
LEVEL CONTROLS
Heat emission
The LEVEL rotary potentiometer is used for changing the input
gain. Although related to output
power, it is not a direct representation
Consumos eléctricos / Power consumption
of it. Thus, we can have maximum
Potencia de salida /
output power with the gain at mid
Carga /
Output Power
position. Similarly, we may have the
load
Sin señal
Max
1/3
1/8
gain controls at maximum and not
idle
5.0
2.6
1.1
0.3
have maximum output if our source
8.0
4.7
1.9
0.3
signal is not hot enough.
model
H-1500
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
8.2
4.7
1.9
0.3
H-2200
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
8.0
12.0
12.0
4.0
7.3
7.35
1.8
3.0
3.0
0.6
0.6
0.6
H-4000
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
12.0
20.0
20.0
5.5
9.7
9.7
2.3
5.8
5.8
0.6
0.6
0.6
One way to use the volume controls is
to set them such that when the
mixer’s faders are at their maximum
level, we are just below clipping level
on the amplifier or clipping very
occasionally.
Carga /
model
load
Output Power
Max
1/3
1/8
BTU/h
Kcal/h
BTU/h
Kcal/h
BTU/h
idle
Kcal/h
BTU/h
Kcal/h
H-1500
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
2960
4725
3350
745
1190
845
1720
3170
2665
435
800
670
740
1295
1105
185
325
280
235
235
235
60
60
60
H-2200
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
4555
6835
4285
1150
1720
1080
2565
4865
4065
645
1225
1025
1195
2025
1710
300
510
430
470
470
470
120
120
120
H-4000
8+8 ohm
4+4 ohm
Puente/bridge 8 ohm
6495
10880
6120
1635
2740
1540
3345
6015
4445
845
1515
1120
1435
3940
3345
360
995
845
470
470
470
120
120
120
Serie H / H series
13
SPECIFICATIONS
H-2200
H-4000
280 W
450 W
750 W
900 W
1500 W
500 W
850 W
750 W
1400 W
1100 W
2000 W
1500 W
2800W
2200 W
4000 W
<0.05%
0.02%
0.02%
0.03%
45 V/us
56V/us
65V/us
20Hz – 20kHz +0/-0.5dB, 5Hz – 48kHz –3dB
>310
1V/1.3V
1.34V/1.5V
1.84V/1.96V
32 dB (40x)
10K Ohm no bal./unbal., 20K Ohm bal.
Clase H / Class H
14 Kg (31 lbs.)
15 Kg (33 lbs.)
30 Kg (65 lbs.)
Véase sección Dibujos de línea / See Line Drawings section
LINE DRAWINGS
2U models (H-1500, H-2200):
3U models (H-4000):
Serie H / H series
Manual del usuario / User's manual
14
APPENDIX A. Bridge Mode Operation
To operate in bridge mode, follow these steps:
1.
Switch off the amplifier.
2.
Turn volume control potentiometers on the front panel to minimum position (fully anticlockwise).
3.
Connect input signal to channel A.
4.
Set mode switch to “BRIDGE”.
5.
Connect speakers as follows:
Connect (+) to red speaker terminal on channel A’s output terminals
Connect (-) to red speaker terminal on channel B’s output terminals
6. Turn volume control potentiometers on the front panel to maximum position (fully clockwise).
7. Control volume levels from the mixer or pre-amp only.
NOTE: We do not recommend using bridge mode with loads lower than 4 ohms
Serie H / H series
Manual del usuario / User's manual
15
APPENDIX B. Line connections : unbalanced and balanced
There are two basic ways to transport an audio signal:
Unbalanced line: Utilising a two-conductor cable, it transports the signal as the voltage between them. Electro-magnetic
interference can get added to the signal as undesired noise. Connectors that carry unbalanced signals have two pins, such as RCA
(Phono) and 1/4” (6.35 mm, often referred to as jack) mono. 3-pin connector such as XLR (Cannon) may also carry unbalanced signals
if one of the pins is unused.
Balanced line: Utilising a three-conductor cable, one of them acts as a shield against electro-magnetic noise and is the
ground conductor. The other two have the same voltage with respect to the ground conductor but with opposite signs. The noise that
cannot be rejected by the shield affects both signal conductors in the same way. At the device’s input the two signals get summed
with opposite sign, so that noise is cancelled out while the programme signal doubles in level. Most professional audio devices use
balanced inputs and outputs. Connectors that can carry balanced signal have three pins, such as XLR (Cannon) and 1/4” (6.35 mm)
stereo.
The graphs that follow show the recommended connection with different types of connectors to balanced processor or amplifier
inputs. The connectors on the left-hand side come from a signal source, and the ones on the right hand side go to the inputs of the
processor or amplifier. Note that on the unbalanced connectors on the left-hand side, two terminals are joined inside the connector. If
hum occurs with balanced to balanced connections, try disconnecting the sleeve (ground) on the input connector. Note that the
illustrations show what should be connected to what, but that pin locations on an actual XLR connector are different. Also, pin 2 hot is
assumed on XLR connectors.
Serie H / H series
Manual del usuario / User's manual
16
APPENDIX C. Tables for cable selection
The table below is intended to aid the selection of the appropriate cable. Power loss and resulting damping factor are shown for
different values of cable length and area. A minimum damping factor of 25 is recommended, preferably not lower than 50 for quality
installations. Although a power loss of 10% may not be significantly audible, the resulting low damping factor means that the amplifier
will not be able to control the loudspeaker, resulting in a coloured and muddy bass sound.
LONGITUD /
LENGTH
CALIBRE
AWG (Nr.)
AREA
R (ohm)
PÉRDIDA DE POTENCIA /
POWER LOSS
FACTOR DE
AMORTIGUAMIENTO /
DAMPING FACTOR
8 ohm
4 ohm
8 ohm
4 ohm
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.103
0.066
0.041
0.026
0.016
0.010
1,3 %
0,8 %
0,5 %
0,3 %
0,2 %
0,1 %
2,6 %
1,7 %
1,0 %
0,7 %
0,4 %
0,3 %
61
85
115
147
179
207
30
42
57
73
90
104
5 m (16.4 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.207
0.131
0.082
0.052
0.033
0.021
2,5 %
1,6 %
1,0 %
0,7 %
0,4 %
0,3 %
5,0 %
3,3 %
2,1 %
1,3 %
0,8 %
0,5 %
34
50
72
99
130
161
17
25
36
50
65
81
7,5 m (24.6 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.310
0.197
0.123
0.079
0.049
0.031
3,9 %
2,5 %
1,5 %
1,0 %
0,6 %
0,4 %
7,8 %
4,9 %
3,1 %
2,0 %
1,2 %
0,8 %
24
35
53
74
103
134
12
18
26
37
52
67
10 m (33 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.413
0.262
0.164
0.105
0.066
0.041
5,1 %
3,3 %
2,1 %
1,3 %
0,8 %
0,5 %
10,2 %
6,6 %
4,1 %
2,6 %
1,6 %
1,0 %
18
28
42
60
85
115
9
14
21
30
42
57
15 m (49 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.620
0.393
0.246
0.157
0.098
0.062
7,8 %
4,9 %
3,1 %
2,0 %
1,2 %
0,8 %
15,6 %
9,8 %
6,2 %
3,9 %
2,5 %
1,6 %
12
19
29
43
63
88
6
9
15
22
31
44
20 m (66 ft)
18
16
14
12
10
8
0,8 mm2
1,31 mm2
2,1 mm2
3,3 mm2
5,3 mm2
8,35 mm2
0.827
0.525
0.328
0.210
0.131
0.082
10,3 %
6,5 %
4,1 %
2,6 %
1,6 %
1,0 %
20,6 %
13,1 %
8,2 %
5,3 %
3,3 %
2,0 %
9
14
22
34
50
72
5
7
11
17
25
36
50 m (164 ft)
16
14
12
10
8
6
1.31 mm2
2.1 mm2
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.313
0.820
0.525
0.328
0.205
0.125
16.4 %
7.7 %
4.9 %
3.1 %
1.9 %
1.6 %
32.8 %
15.4 %
9.8 %
6.1 %
3.9 %
3.1 %
6
12
19
29
44
52
3
6
10
15
22
26
75 m (246 ft)
14
12
10
8
6
2.1 mm2
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.230
0.788
0.491
0.308
0.186
15.4 %
9.9 %
6.1 %
3.9 %
2.3 %
30.8 %
19.7 %
12.3 %
7.7 %
4.7 %
6
9
15
24
37
3
5
8
12
19
100 m (328 ft)
12
10
8
6
3.3 mm2
5.3 mm2
8.35 mm2
13.3 mm2
1.050
0.655
0.410
0.248
13.1 %
8.2 %
5.1 %
3.1 %
26.3 %
16.4 %
10.2 %
6.2 %
7
12
18
29
4
6
9
14
2,5 m (8.2 ft)
Serie H / H series
17
NOTAS / NOTES
Serie H / H series
620 W
950 W
--1900 W
--<0.05%
0.02%
60 V/us
20Hz – 20kHz +0/-0.5dB,
5Hz – 48kHz –3dB
>310
1.54V/1.76V
32 dB (40x)
10K Ohm no bal./unbal., 20K
Ohm bal.
Clase H / Class H
17.4 Kg (38.3 lbs.)
88 x 482.6 x 406.6 mm
18
UM_H_01
www.dasaudio.com
D.A.S. AUDIO OF AMERICA, INC.
Sunset Palmetto Park
6816 NW 77th Court.
Miami, FL. 33166 - U.S.A.
TOLL FREE: 1-888DAS4USA
Tel. +1 305 436 0521
Fax +1 305 436 0528
D.A.S. AUDIO ASIA PTE. LTD.
25 Kaki Bukit Crescent #01-00/02-00
Kaki Bukit Techpark 1
Singapore 416256
Tel. +65 6742 0151
Fax +65 6742 0157