Quick Installation Guide

LevelOne IP Camera
Wired/Wireless Network Camera
한국어
繁體中文
This guide covers only the most common situations. All detail
information is described in the user manual.
Windows 98SE, Millennium Edition (ME), 2000,XP and VISTA
operating systems
z
Browser: Internet Explorer 5.5 or above
NOTE:
All the captured images of installation mentioned in this user manual
were based on Windows XP operating system. For installation on
other Windows OS, e.g. Windows 98SE, all the procedures remains
the same.
English
Using the Software CD to configure the camera
„
„
„
„
„
„
„
„
„
„
„
„
Power on your PC and insert the CD-ROM
The setup page should load automatically. If it does not, please
select your CD-ROM drive manually to open the setup page.
Select “Install Software”->“Installation Wizard” to initiate the
installation.(Fifure1-1)
Read the license agreement thoroughly then click ”I Agree”
(Figure 1-2)
Click “Next” to start the installation.( Figure 1-3)
If you wish to install the software program in an alternate
location, click “Browse”, otherwise click “Install” to move on to
the next step. (Figure 1-4)
Click “Close” to complete the software installation.(Figure 1-5)
Run “Installation Wizard”. (Figure 2-1)
The Installation Wizard will show MAC address and an IP
Address of available LevelOne Network Cameras. Highlight
the MAC address and double click to link to the selected
device.(Figure 2-2)
The default user name of CCD Network camera is “root” and
password is the MAC address (in capital letters) while CMOS
Network camera will not ask for any account and password.
The following screen would appear automatically. Click “Yes”
and proceed. LevelOne Network Cameras should be active by
now. (Figure 2-3)
Congratulations, you can use the camera through the network
to view the video.(Figure 2-4)
Installing IP CamSecure
Click ”IP CamSecure” and follow the onscreen instruction or refer to
the user’s manual to complete installation.(Figure 3-1)
„
„
„
Français
Using the Software CD to configure the camera
„
„
„
„
„
„
„
„
„
„
„
„
Installation IP CamSecure
„
„
„
„
„
„
„
„
„
„
„
„
„
raadpleeg de gebruikershandleiding om de installatie te
voltooien.(Figure3-1)
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
Installering af IP CamSecure
„
„
„
„
„
„
„
„
„
„
„
„
„
Installera IP CamSecure
„
„
„
Instalacija programa IP CamSecure
Kliknite ”IP CamSecure” in sledite navodilom na zaslonu ali pa
„
„
„
„
„
„
„
„
„
„
Installing IP CamSecure
繁體中文
軟體安裝
„
„
„
„
„
„
„
„
„
„
„
„
將包裝內所附的 CD-ROM 放入光碟機中
螢幕會自動出現安裝畫面. 如果沒看到安裝畫面，請到光碟片的
路徑中，手動安裝。
點選“Install Software”->“Installation Wizard”，並開始安裝。
(Figure1-1)
詳讀軟體授權合約後點選”I Agree”。(Figure1-2)
點選“Next”。(Figure1-3)
如果你要改變軟體安裝路徑，請點選“Browse”；否則就直接點
選“Install”，繼續安裝。(Figure1-4)
點選“Close”，完成軟體安裝程序。(Figure1-5)
執行”Insatllation Wizard”。(Figure2-1)
出現 Installation Wizard 的畫面，並偵測到網路上已架設完成的
攝影機，及詳列 MAC address 與 IP Address。滑鼠雙擊欲設定
的攝影機的 MAC address，連結至該網頁。 (Figure2-2)
CCD 網路攝影機的預設帳號為”root”,密碼為該網路攝影機的
MAC address(大寫字母),CMOS 網路攝影機則不會詢問任何帳
號及密碼。
當您成功登入後，會自動跳出 ActiveX 詢問視窗；點選”Yes”。
(Figure2-3)
恭喜您，您已經可以開始使用此台網路攝影機了。(Figure2-4)
安裝 IP CamSecure
點選”IP CamSecure”, 依照顯示的步驟或參閱使用手冊完成安裝。
(Figure3-1)
„
„
„
„
„
„
‫‪Installing IP CamSecure‬‬
‫„‬
‫اﻧﻘﺮ "‪ " IP CamSecure‬واﺗﺒﺎع اﻟﺘﻌﻠﻴﻤﺎت ﻋﻠﻰ اﻟﺸﺎﺷﻪ او اﻟﺮﺟﻮع اﻟﻰ دﻟﻴﻞ اﻟﻤﺴﺘﺨﺪم‬
‫ﻹﺗﻤﺎم اﻟﺘﺮآﻴﺐ‪.‬‬">