advertisement
▼
Scroll to page 2
of 56
Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Operator’s Manual Manual del Operario Manuel de l'Utilisation 10kW / 12kW Rated Home Generator Models 01938-0 & 01815-0 Part No. 192384GS Rev. E (05/10/06) www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual TABLE OF CONTENTS TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 5 For the Home Owner: . . . . . . . . . . . . . . . . . . . . . 5 For the Installing Dealer/Contractor: . . . . . . . . . 5 OWNER ORIENTATION . . . . . . . . . . . . . . . . . . . . . . . . . 5 Fuel Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Decrease at High Altitude or High Temperature . . . . . . . . . . . . . . . . . . . . . 6 Generator Location . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Generator Clearances . . . . . . . . . . . . . . . . . . . . . . . 6-7 Essential Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Essential Circuit Selection . . . . . . . . . . . . . . . . 7-8 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Delivery Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Shipment Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 KNOW YOUR HOME STANBY GENERATOR . . . . . . . . 9 KNOW YOUR SYSTEM CONTROL PANEL . . . . . . . . . 10 Access Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 To remove an access door: . . . . . . . . . . . . . . . . 11 To install an access door: . . . . . . . . . . . . . . . . . . 11 BEFORE INITIAL START-UP . . . . . . . . . . . . . . . . . . . . . . 12 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Oil Considerations . . . . . . . . . . . . . . . . . . . . . . . 12 Battery Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Gaseous Fuel System . . . . . . . . . . . . . . . . . . . . . . . . 12 AUTOMATIC OPERATION . . . . . . . . . . . . . . . . . . . . . . 13 Checking Automatic Operation . . . . . . . . . . . . . . . . 13 Servicing the System . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setting Exercise Timer . . . . . . . . . . . . . . . . . . . . . . . . 13 FAULT DETECTION SYSTEM . . . . . . . . . . . . . . . . . . . . . 14 Reset Fault Detection System . . . . . . . . . . . . . . 14 No LED - Discharged Battery . . . . . . . . . . . . . . 14 Low Battery Voltage . . . . . . . . . . . . . . . . . . . . . . 14 Low Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . 14 Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Engine Fail To Start . . . . . . . . . . . . . . . . . . . . . . . 15 Low Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Engine Overspeed . . . . . . . . . . . . . . . . . . . . . . . 15 Oil Temperature High . . . . . . . . . . . . . . . . . . . . 15 GENERATOR MAINTENANCE . . . . . . . . . . . . . . . . . . . 16 Changing Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 16 To Clean the Generator . . . . . . . . . . . . . . . . . . . . . . 16 When Calling the Factory . . . . . . . . . . . . . . . . . . . . . 16 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-37 FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-56 Copyright © 2006 Briggs & Stratton Power Products Group, LLC. All rights reserved. No part of this material may be reproduced or transmitted in any form by any means without the express written permission of Briggs & Stratton Power Products Group, LLC. 2 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual SAVE THESE INSTRUCTIONS IMPORTANT SAFETY RULES DANGER Storage batteries give off explosive hydrogen gas during recharging. Slightest spark will ignite hydrogen and cause explosion. Battery electrolyte fluid contains acid and is extremely caustic. Contact with battery contents will cause severe chemical burns. A battery presents a risk of electrical shock and high short circuit current. The safety alert symbol ( ) is used with a signal word (DANGER, CAUTION,WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION, when used without the alert symbol, indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death. The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard.The warnings in this manual, and the tags and decals affixed to the unit are, therefore, not all-inclusive. If you use a procedure, work method or operating technique that the manufacturer does not specifically recommend, you must satisfy yourself that it is safe for you and others.You must also make sure that the procedure, work method or operating technique that you choose does not render the generator unsafe. • DO NOT dispose of battery in a fire. • DO NOT allow any open flame, spark, heat, or lit cigarette during and for several minutes after charging a battery. • DO NOT open or mutilate the battery. • Wear protective goggles, rubber apron, and rubber gloves. • Remove watches, rings, or other metal objects. • Use tools with insulated handles. WARNING Running generator gives off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. NOTE: Your generator is equipped with a spark arrester muffler.The spark arrester must be maintained in effective working order by the owner/operator. In the State of California, a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. • Operate generator ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings. WARNING Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C). Severe burns can occur on contact. Exhaust heat/gases can ignite combustibles or structures causing a fire. Hazard Symbols and Meanings Toxic Fumes Rotating Parts Hot Surface Electrical Shock • DO NOT touch hot surfaces and avoid hot exhaust gases. • Allow equipment to cool before touching. • Keep at least 5 ft. (152 cm) clearance on all sides of generator including overhead. • Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws. Fire Chemical Burn 3 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual CAUTION WARNING Excessively high operating speeds increase risk of injury and damage to generator. Excessively low speeds impose a heavy load. Generator produces powerful voltage. Failure to properly ground generator can result in electrocution. Failure to isolate generator from power utility can result in death or injury to electric utility workers due to backfeed of electrical energy. • DO NOT tamper with governed speed. Generator supplies correct rated frequency and voltage when running at governed speed. • DO NOT modify generator in any way. • When using generator for backup power, notify utility company. • DO NOT touch bare wires or receptacles. • DO NOT use generator with electrical cords which are worn, frayed, bare or otherwise damaged. • DO NOT handle generator or electrical cords while standing in water, while barefoot, or while hands or feet are wet. • If you must work around a unit while it is operating, stand on an insulated dry surface to reduce shock hazard. • DO NOT allow unqualified persons or children to operate or service generator. • In case of an accident caused by electrical shock, immediately shut down the source of electrical power and contact the local authorities. Avoid direct contact with the victim. • Before performing any maintenance on the generator, disconnect the battery cable indicated by a NEGATIVE, NEG or (-) first.When finished, reconnect that cable last. • After your Home Standby Generator is installed, the generator may crank and start without warning any time there is a power failure.To prevent possible injury, always set the AUTO/OFF/MANUAL switch to OFF AND remove the 15 Amp fuse BEFORE working on the equipment. CAUTION Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it. • See “Essential Circuits”. • Start generator and let engine stabilize before connecting electrical loads. CAUTION Improper treatment of generator can damage it and shorten its life. • Use generator only for intended uses. • If you have questions about intended use, ask dealer or contact Briggs and Stratton. • Operate generator only on level surfaces. • Adequate, unobstructed flow of cooling and ventilating air is critical to correct generator operation. • The Oil Service door and/or the Control Panel door must be installed whenever the unit is running. • DO NOT expose generator to excessive moisture, dust, dirt, or corrosive vapors. • Despite the safe design of the Home Standby Generator, operating this equipment imprudently, neglecting its maintenance or being careless can cause possible injury or death. • Remain alert at all times while working on this equipment. Never work on the equipment when you are physically or mentally fatigued. • DO NOT start engine with air cleaner or air cleaner cover removed. • DO NOT insert any objects through cooling slots. • DO NOT use the generator or any of its parts as a step. Stepping on the unit can cause stress and break parts.This may result in dangerous operating conditions from leaking exhaust gases, fuel leakage, oil leakage, ect.. • If connected devices overheat, turn them off and disconnect them from generator. • Shut off generator if: -electrical output is lost; -equipment sparks, smokes, or emits flames; -unit vibrates excessively. WARNING Propane and Natural Gas are extremely flammable and explosive. Fire or explosion can cause severe burns or death. • Install the fuel supply system according to applicable fuel-gas codes. • Before placing the Home Standby Generator into service, the fuel system lines must be properly purged and leak tested. • After the generator is installed, you should inspect the fuel system periodically. • NO leakage is permitted. • DO NOT operate engine if smell of fuel is present or other explosive conditions exist. • DO NOT smoke around the generator.Wipe up any oil spills immediately. Ensure that no combustible materials are left in the generator compartment. Keep the area near the generator clean and free of debris. 4 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual SAVE THESE INSTRUCTIONS To arrange for proper installation, contact the store at which you purchased your Briggs & Stratton Home Standby Generator, your dealer, a licensed electrician or your utility power provider. This manual contains important instructions that should be followed during installation and maintenance of the generator and battery. The HSG Warranty is VOID unless the system is installed by licensed electrical and plumbing professionals. INTRODUCTION Thank you for your purchase of a Briggs & Stratton Home Standby Generator (HSG).This product is intended for use as an optional home standby system which provides an alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication systems that, when stopped during any power outage, could cause discomfort, or the like.This product does not qualify for emergency standby as defined by NFPA 70 (NEC). For the Installing Dealer/Contractor: For most applications, the Installation manual contains all the information required to properly install and start the Home Standby Generator.This Operator’s Manual describes essential circuit selection, routine operation and owner maintenance procedures. Briggs and Stratton has made every effort to provide for a safe, streamlined and cost-effective installation. Because each installation is unique, it is impossible to know of and advise the trade of all conceivable procedures and methods by which installation might be achieved. Neither could we know of possible hazards and/or the results of each method or procedure. For these reasons, The Emission Control System for this generator is warranted for standards set by the U.S. Environmental Protection Agency and by the California Air Resources Board (CARB). If you need more information, call 1-800-743-4115, between 8:00 AM and 5:00 PM CT. OWNER ORIENTATION Only current licensed electrical and plumbing contractors should attempt HSG installations. Installations must strictly comply with all applicable codes, industry standards and regulations. This section provides Home Standby Generator owners with the information necessary to achieve the most satisfactory and cost effective installation possible. The illustrations are for typical circumstances and are meant to familiarize you with the installation options available with your Home Standby Generator. A thorough understanding of these options will provide fundamental control over the cost of your installation, as well as ensure your final satisfaction and security. Federal and local codes, appearance, noise levels, fuel types, and distances are the factors that must be considered when negotiating with an installation professional. Remember that as the distance from the existing electrical service and gaseous fuel supply increases, equal compensations in piping and wiring materials must be allowed for.This is necessary to comply with local codes and overcome electrical voltage drops and gaseous fuel pressure drops. The factors mentioned above will have a direct affect on the overall price of your Home Standby Generator installation. NOTE: In some areas you may need to acquire electrical permits for installing the Home Standby Generator, building permits for installing gas lines, and permits for noise allowances.Your installer should check your local codes AND obtain the permits before installing the system. Your Briggs & Stratton Home Standby Generator is supplied with this “Operator’s Manual” and a separate “Installation Manual” (part number 192385GS).These are important documents and should be retained by the owner after the installation has been completed. Installation Assistance For the Home Owner: To help you make informed choices and communicate effectively with your installation contractor(s), Read and understand the Owner Orientation Section of this manual BEFORE contracting or starting your HSG installation. 5 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual Generator Location An important consideration affecting the entire installation is the type of fuel used by your Home Standby Generator. The system was factory tested and adjusted using natural gas as a fuel. Liquid propane (LP) may also be used as a fuel (see the Installation Manual). The actual physical location of your HSG has a direct affect on: 1. The amount of plumbing required to fuel your generator. 2. The amount of wiring required to control and connect your generator. NOTE: Specific location guidelines are discussed in the Installation Manual. Acquaint yourself with that information and confer with your installer. Be sure to ask how your site might affect installation costs and compliance with local codes and standards. Although there are specific factors that are inherent to each of these fuels, your location and the duration of possible utility interruptions should guide your selection of fuel type. For urban installations, Natural Gas (if available) should be your fuel of choice. For remote installations, a Liquefied Petroleum (LP) tank might better meet your needs. Home Standby Generator Location For proper engine function, the following fuel guidelines are recommended: Before installing generator, consult with homeowner and convey the following guidelines which may affect the desired location. • Use clean, dry fuel, free of moisture or any particulate material. Using fuels outside the following recommended values may cause performance problems. Generator Clearances WARNING In engines set up to run on propane (LP) gas, commercial grade HD5 propane with a minimum fuel energy of 2500 BTUs/ft3 with maximum propylene content of 5% and butane and heavier gas content of 2.5% and minimum propane content of 90%. Running generator gives off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide will cause nausea, fainting or death. • Operate generator ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings. WARNING Propane and Natural Gas is extremely flammable and explosive. Fire or explosion can cause severe burns or death. Place generator in a well ventilated area which will allow for removal of deadly exhaust gas. DO NOT install generator where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes or other openings that can allow exhaust gas to collect in a confined area (Figure 1). Prevailing winds and air currents should be taken into consideration when positioning generator. • The Home Standby Generator is equipped with an automatic safety gas “fuel shut-off” valve. • DO NOT operate the equipment if the “fuel shut-off” valve is missing or inoperative. Power Decrease at High Altitude or High Temperature Air density is less at high altitudes, resulting in less available engine power. Specifically, engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6°C) above 77°F (25°C). Make sure you and your installer consider these factors when determining total generator load. General Location Guidelines • Install the unit outdoors ONLY. • Place the unit in a prepared location that is flat and has provisions for water drainage. • Install the unit in a location where sump pump discharge, rain gutter down spouts, roof run-off, landscape irrigation, or water sprinklers will not flood the unit or spray the enclosure and enter any air inlet our outlet openings. • Install the unit where the location of any services such as phone, electrical, fuel, air conditioning, irrigation, including covered, concealed and underground services will not be affected or obstructed. 6 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual Figure 1 — Home Standby Generator Clearances Figure 2 — Wattage Reference Guide Running Watts 1700 Air Conditioner (12,000 Btu)* 3800 Air Conditioner (24,000 Btu)* 6000 Air Conditioner (40,000 Btu)* Battery Charger (20 Amp) 500 800 to 1000 Circular Saw (6-1/2") 5750 Clothes Dryer (Electric)* 700 Clothes Dryer (Gas)* 1150 Clothes Washer* 1750 Coffee Maker 2000 Compressor (1 HP)* 1400 Compressor (1/2 HP)* 1800 Compressor (3/4 HP)* 700 Curling Iron 650 Dehumidifier* 400 Electric Blanket 1500 Electric Range (per element) 1250 Electric Skillet 700 Freezer* 875 Furnace Fan (3/5 HP)* 500 to 750 Garage Door Opener* 1200 Hair Dryer 250 to 1100 Hand Drill 1200 Iron 800 Jet Pump* 100 Light Bulb 700 to 1000 Microwave Oven 1100 Milk Cooler* 300 Oil Burner on Furnace 400 Oil Fired Space Heater (140,000 Btu) 150 Oil Fired Space Heater (30,000 Btu) 225 Oil Fired Space Heater (85,000 Btu) 50 to 200 Radio 700 Refrigerator 200 Slow Cooker 2000 Submersible Pump (1 HP)* 1500 Submersible Pump (1/2 HP)* 2800 Submersible Pump (1-1/2 HP)* 800 to 1050 Sump Pump* 1750 to 2000 Table Saw (10")* Television 200 to 500 1000 to 1650 Toaster *Allow three (3) times listed watts for starting device Device Exhaust Port • Install the unit where air inlet and outlet openings will not become obstructed by leaves, grass, snow, etc. If prevailing winds will cause blowing or drifting, you may need to construct a windbreak to protect the unit. • Install the generator as close as possible to the Transfer Switch to reduce the length of wiring and conduit. • Install the generator as close as possible to the fuel supply to reduce length of pipes. IMPORTANT: Laws or local codes may regulate the distance to the fuel supply. The Home Standby Generator is shipped already attached to its mounting pad. Unless mandated by local code, a concrete slab is not required. If mandated by local code, construct a concrete slab at least 3 inches thick and 6 inches longer and wider than the unit. Attach unit to slab with 1/4” diameter (minimum) masonry anchor bolts long enough to retain the unit. Essential Circuits As a Home Standby Generator owner, it is important that you clearly identify the circuits in your building that are "essential" to you. It is important that your installer understand which circuits you want to include as "Essential Circuits". Depending on the power consumed by these circuits, most or all of them can be switched to the Home Standby Generator for the duration of normal power interruption. The wattage reference guide shown in Figure 2 will assist you with your decision-making process. It provides the wattage used by many ordinary household devices. Use it as a guide when selecting your essential circuits. Review this information with your installer and ask about any technical considerations that might affect the cost of your installation. 7 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual Essential Circuit Selection When selecting the essential circuits that will be switched to “Standby Power,” it is important that the sum of the combined circuit loads does not exceed the wattage/amperage capacity of the generator.To help you with your selection of essential circuits, please consider the following: turn off any non essential loads. Failure to turn off non essential loads could overload the generator causing it to shut down. Some examples of non essential loads are as follows: • Pool pump • Hot tub • Electric hot tub and/or pool heaters • Central air conditioners • Electric hot water heaters • Electric range and/or oven • Arc welder • Non essential electric heaters Add up the total wattage of all electrical devices to be connected at one time.This total should NOT be greater than the generator’s wattage capacity. The rated wattage of lights can be taken from light bulbs. The rated wattage of tools, appliances and motors can usually be found on a data plate or decal affixed to the device. UNPACKING If the appliance, tool or motor does not give wattage, multiply volts times the ampere rating to determine watts (Volts x Amps = Watts). Refer to the Installation Manual for detailed unpacking instructions, if desired. Delivery Inspection Some electric motors (induction types) require about three times more watts of power for starting than for running.This surge lasts for only a few seconds. Be sure you allow for this high starting wattage when selecting electrical devices that will be energized by the Home Standby Generator: • Figure the watts required to start the largest motor. • Add that to the total running watts of all other connected loads. After removing the carton, carefully inspect the Home Standby Generator for any damage that may have occurred during shipment. IMPORTANT: If loss or damage is noted at time of delivery, have the person(s) making delivery note all damage on the freight bill and affix his signature under the consignor's memo of loss or damage. If loss or damage is noted after delivery, separate the damaged materials and contact the carrier for claim procedures. Missing or damaged parts are not warranted. This Briggs & Stratton Home Standby Generator complies with the following “stationary standby power rating”: Shipment Contents The Home Standby Generator is supplied with: • Home standby generator • Attached mounting pad • One 24” flexible fuel hook-up hose • Installation manual (P/N 192385GS) • Operator’s manual (P/N 192384GS) • Illustrated parts list manual (P/N 193208GS for model 01815 or P/N 193918GS for model 01938) • Installation checklist (P/N 190840GS) • Three access door keys • Four lifting hole plugs • Oil fill spout • Touch-up paint • One spare 15 Amp fuse • Diagnostic LED kit (diode/plate/decal/pin connectors (2)) The standby power rating is applicable for supplying power for the duration of normal power interruption. NO sustained overload capability is available for this rating. This rating is applicable to installations served by a reliable normal utility source.This rating is only applicable to variable loads with an average load factor of 80% of the standby rating.The standby rating is only applicable for optional standby power where the generator set serves as the backup to the normal utility source. Use the “Wattage Reference Guide” provided and mark those circuits you consider “critical” or “essential”. Make sure you and your installer consider the system’s altitude above sea level and the ambient temperature range when determining total generator load. IMPORTANT: When using the 100 Amp or 200 Amp transfer switch with the Home Standby Generator, you must 8 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual KNOW YOUR HOME STANDBY GENERATOR Read this Operator’s Manual and safety rules before operating your generator. Compare the illustrations with your generator to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. 15 Amp Fuse Oil Drain Hose Oil Fill Cap Air Cleaner Oil Dip Stick Unit Data Decal Battery Oil Filter Engine Label Battery Door Opening Control Panel Door Opening Oil Service Door Opening 15 Amp Fuse — Protects the DC control circuits. Engine Label — Identifies engine model and type. Air Cleaner — Uses a dry type filter element and foam precleaner to limit the amount of dirt and dust drawn into the engine. Exhaust Port — High-performance muffler lowers engine noise to comply with most residential codes. Battery — 12 Volt DC, 33 Amp-Hour sealed battery provides power to start the engine. Battery receives trickle charge whenever generator is not running. Oil Drain Hose — Provided to facilitate oil changing. Oil Dip Stick — Used to check the engine oil level. Oil Fill Cap — Remove to service the engine with recommended oil. Control Panel — Used for various test, operation and maintenance functions. See “KNOW YOUR SYSTEM CONTROL PANEL” on the next page. Oil Filter — Filters engine oil to prolong system life. Unit Data Decal — Identifies unit by serial number. 9 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual KNOW YOUR SYSTEM CONTROL PANEL Compare this Control Panel illustration with your generator to familiarize yourself with the location of these important controls: Set Exercise Switch Circuit Breaker Diagnostic LED Hour Meter AUTO/OFF/MANUAL Switch 15 Amp Fuse 15 Amp Fuse — Protects the Home Standby Generator DC control circuits. If the fuse has ‘blown’ (melted open) or was removed, the engine cannot crank or start. Replace the fuse using only an identical BUS AGC 15A fuse. Circuit Breaker — Protects the system from shorts and other over-current conditions. Must be ON to supply power to the Automatic Transfer Switch. Diagnostic LED — Used for troubleshooting operational problems with the Home Standby Generator. All fault conditions are described in the section “Fault Detection System”. AUTO/OFF/MANUAL Switch — This three-position switch is the most important control on the system and is used as follows: • “AUTO” position is the normal operating position. If a utility power outage is sensed, the system will start the generator.When utility power is restored, lets the engine stabilize internal temperatures, shuts off the generator, and waits for the next utility power outage. Hour Meter — The hour meter records the total number of hours the generator has been running and is used to schedule maintenance tasks. Set Exercise Switch — Used to set the exercise cycle start time and day-of-the-week. Exercise cycle only occurs in AUTO mode. • “OFF” position turns off running generator, prevents unit from starting and resets any detected faults. • “MANUAL” position starts the engine after a short amount of time. It is used for maintenance or diagnostic functions. 10 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual Access Doors door channel.The door will come free of generator enclosure. The Battery door does not have a lock and the Air Intake door does not have a lock or lift handle.The Air Intake door is opened by lifting on the louvers instead of a lift handle. However, you must remove the door lock screws, found directly above the center of the doors. The Home Standby Generator is equipped with an enclosure that has four access doors (Figure 3).The doors are named for a significant component located behind them. Starting with the side that has the fuel connection and proceeding clockwise, the doors are named: • Oil Service door • Air Intake door • Control Panel door • Battery door Each Home Standby Generator is equipped with three identical keys.These keys fit the locks that secure the Oil Service and Control Panel doors. WARNING Running engines produce heat.Temperature of exhaust port and nearby areas can reach or exceed 600°F (316°C). Severe burns can occur on contact. • DO NOT touch hot surfaces. • Allow equipment to cool before touching. CAUTION To Install an Access Door: 1. Support door by grasping lift handle or louver. Guide top of door into generator enclosure. 2. Lift door up into its upper channel until security pins clear sill of enclosure. 3. Push lower half of door into door recess until it is flush with sides. 4. Seat door by pushing it down until rubber coated security pins engage and door rests on mounting sill. 5. If installing a lockable door, turn key one quarter turn counterclockwise. Remove key. 6. If installing air intake or battery door, replace the door lock screw. DO NOT operate the Home Standby Generator unless the Oil Service and/or Control Panel doors are installed. • Failure to install Oil Service and/or Control Panel doors while operating the Home Standby Generator will cause overheating. To Remove an Access Door: 1. Insert key into lock of access door you wish to remove and turn one quarter turn clockwise. NOTE: The key is retained in the lock when the locks are open. 2. Grasp door’s lift handle and pull door upwards until security pins are free of lower base. 3. With security pins free, pull lift handle outward (away) from unit while pulling door down and out of upper Figure 3 — Enclosure Access Doors Door Lock Screw Exhaust Port Door Lock Screw Air Int ake Do or r oo D ice erv S l Oi Bat ter y Do or 11 www.mymowerparts.com or Do l ane lP o r nt Co Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual BEFORE INITIAL START-UP Battery Connection The Home Standby Generator is supplied with a 12 Volt DC 33 Amp-Hour, valve regulated battery. It is a sealed, lead-acid rechargeable battery. It is installed in the unit and the battery cables are connected at the factory.The generator’s 15 Amp fuse has been removed to prevent the unit from starting during shipping. Engine Oil This engine is shipped from the factory filled with the recommended oil. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine operator’s manual. CAUTION CAUTION Installing the 15A fuse could cause the engine to start. Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure. • DO NOT install the 15 Amp fuse until all plumbing and wiring has been completed and inspected. NOTE: With the battery installed, all wiring to transfer switch and Home Standby Generator completed, utility power supplied to the Automatic Transfer Switch, and the unit in AUTO mode, the battery receives a trickle charge while the engine is not running.The trickle charger cannot be used to recharge a battery that is completely discharged. • Refer to engine manual for oil fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. Oil Considerations Your Home Standby Generator is equipped with an engine that has been pre-run at the factory and does not require the traditional “break-in” procedure. Gaseous Fuel System • Ensure that all fuel connections are tight, secure and without leaks. The system is filled with synthetic oil (API SJ/CF 5W-30W). This allows for system operation in the widest range of temperature and climate conditions. • Ensure that all shutoff valves are OPEN and that adequate pressure is available (see installation manual). NOTE: The use of synthetic oil DOES NOT alter the required oil change intervals described in the engine operator’s manual. WARNING Propane and Natural Gas is extremely flammable and explosive. Fire or explosion can cause severe burns or death. • DO NOT operate engine if smell of fuel is present or other explosive conditions exist. • If you smell ‘raw’ gaseous fuel (natural or LP) near the unit, immediately turn off the gas supply to the Home Standby Generator. • Contact your gas utility or the system installer for assistance in determining the source of the smell. 12 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual AUTOMATIC OPERATION Servicing the System To service system: To select automatic operation, do the following: 1. Set the service disconnect or main distribution panel circuit breaker that sends utility voltage to the transfer switch to ON. 2. Set the generator’s main circuit breaker to its ON position. 3. Set the AUTO/OFF/MANUAL switch to AUTO. CAUTION 1. Set the AUTO/OFF/MANUAL switch to OFF. 2. Set the generator’s main circuit breaker to its OFF position. 3. Utility voltage is present. Disconnect power before servicing by removing the two 2 Amp fuses from the transfer switch. Setting Exercise Timer With the switch set to AUTO, the engine may crank and start at any time without warning. Such automatic starting normally occurs when utility source voltage drops below a preset level or during the normal exercise cycle. The Home Standby Generator is equipped with an exercise timer that will start and exercise the system once every seven days. During this exercise period, the unit runs for approximately 20 minutes and then shuts down. Electrical load transfer DOES NOT occur during the exercise cycle (unless an utility power outage occurs). • To prevent possible injury that might be caused by such sudden starts, always set the AUTO/OFF/MANUAL switch to OFF. • Remove the 15 Amp fuse before working on or around the generator or transfer switch. A switch on the control panel is labeled “Set Exercise” (depicted on page 10).The specific day and the specific time of day this switch is pressed is programmed into the control board memory.This date and time is then used to automatically initiate the system exercise cycle. Checking Automatic Operation To check the system for proper automatic operation, proceed as follows: 1. Turn OFF the service disconnect or main distribution panel circuit breaker sending power to the automatic transfer switch. The engine will crank and start once the utility voltage drops out and the sensor has timed out. Let the system go through its entire automatic operation sequence. To perform the Set Exercise procedure: 2. With the generator output supplying its loads, turn ON the service disconnect or main distribution panel circuit breaker that supplies utility power to the Automatic Transfer Switch. 3. The automatic transfer switch will transfer loads back to the utility power after 5 minute minimum run time and utility is restored. 4. The generator will run for an additional one minute for engine cool down, then shut down. NOTE: If generator does not shut down after 10 minutes, put AUTO/OFF/MANUAL switch to OFF and contact your installer or local service center. 1. Choose the day and time you want your Home Standby Generator to exercise. 2. On that day and time, set the AUTO/OFF/MANUAL switch to OFF. 3. Press and hold down the “Set Exercise” switch for two seconds. 4. Set the AUTO/OFF/MANUAL switch to AUTO. “Set Exercise” is complete. For example, if you press the “Set Exercise” switch on Sunday morning at 10:00 AM, the unit will run an exercise cycle the following Sunday at 10:00 AM (+/- 1/2 hour). NOTE: “Set Exercise” will only work if the unit is in the Automatic mode and this exact procedure is followed.The exerciser does not need to be re-set if the 15 Amp fuse is removed or changed.The exerciser will need to be re-set if the 12 Volt DC battery is disconnected. If you want to change the day and time the unit exercises, simply perform the “Set Exercise” procedure at the exact weekday and time you want it to take place. This completes the test procedures for automatic operation.The Home Standby Generator will now start automatically when utility power is lost and will supply power to the transfer switch. 13 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual FAULT DETECTION SYSTEM Low Battery Voltage This fault is indicated by one blink.This condition occurs if the generator cannot start because the starting battery output power is below that needed to crank the engine. Causes for this problem may be a faulty battery or trickle charger circuit. The generator may have to run for long periods of time with no operator present. For that reason, the system is equipped with sensors that automatically shut down the generator in the event of potentially damaging conditions, such as low oil pressure, high oil temperature, over speed, and other conditions. To remedy the problem, contact your local service center to check the battery trickle charge output. Remove the 15 Amp fuse and disconnect the battery from the generator. Take the battery to a local battery store for analysis. A light on the generator's control panel is called the Diagnostic LED. A similar LED indicator is installed at a convenient inside location. Both LED's will turn on and off in the same series of blinks if certain problems are detected in your HSG.The blink pattern is repeated with a brief pause between each series.The number of blinks in the series indicates the detected fault, as listed near the control panel, on the mounting plate and as follows: Number of LED Flashes Fault Description 1 Low battery voltage 2 Low oil pressure 3 Low voltage 4 Engine fail to start 5 Low frequency 6 Engine overspeed 7 Oil temperature high Replace the battery after it has been fully recharged, connecting the NEGATIVE cable last. Install the 15 Amp fuse. Low Oil Pressure This fault is indicated by two blinks.The unit is equipped with an oil pressure switch (Figure 4) using normally closed contacts that are held open by engine oil pressure during operation. Should oil pressure drop below the 8 psi range, switch contacts close and the engine is shut down. Figure 4 — Low Oil Pressure & High Temp. Switches Oil Pressure Switch Reset Fault Detection System The operator must reset the fault detection system each time it activates.To do so, place the AUTO/OFF/MANUAL switch in the OFF position for 30 seconds or more. Return the Home Standby Generator to service after correcting the problem by placing the AUTO/OFF/MANUAL switch in the AUTO position. High Temperature Switch Oil Drain Fitting A description of each fault and suggested remedies are as follows: To remedy the low oil pressure condition, add the recommended oil to the FULL mark on the dipstick. No LED - Discharged Battery This condition is caused by a completely discharged battery.To remedy the problem, remove the 15 Amp fuse and disconnect the battery from the generator.Take the battery to a local battery store for analysis. If low oil pressure condition still exists, engine will start, then shut down after about 10 seconds and diagnostic LED will flash. In this case, contact an authorized service facility. Replace the battery after it has been fully recharged, connecting the NEGATIVE cable last. Install the 15 Amp fuse. 14 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual Low Voltage (Generator) This fault is indicated by three blinks.This condition is caused by a restriction in the fuel flow, a broken or disconnected signal lead, a failed alternator winding, the control panel circuit breaker is open, or Home Standby Generator is overloaded. Engine Overspeed This fault is indicated by 6 blinks.This feature protects devices connected to the transfer switch by shutting the generator down if the engine happens to run faster than the preset limit.The overspeed fault is detected as follows: • If the generator output frequency runs at 72 Hz for five seconds, the generator will shut down. To remedy the problem, contact your local service center. • If the generator output frequency reaches 75 Hz, the generator will shut down instantly. Engine Fail To Start This fault is indicated by four blinks.This feature prevents the generator from damaging itself if it continually attempts to start in spite of another problem, such as no fuel supply. Each time the system is directed to start, the unit will crank for 15 seconds, pause for 15 seconds, crank for 15 seconds, pause for 15 seconds, and repeat. If the system does not begin producing electricity after approximately 90 seconds, the unit will stop cranking and the LED will blink. This condition is caused by a failed engine governor.To remedy the problem, you should contact your installer or local service center for assistance. Oil Temperature High This fault is indicated by seven blinks.The contacts of the temperature switch (Figure 4) are normally open. If the engine oil temperature exceeds approximately 140°C (284°F), the fault is detected and the engine shuts down. The most likely cause of this problem is no fuel supply. Check the inside and outside fuel shut off valves to ensure they are fully open. Other causes could be failed spark plug(s), failed engine ignition, or the engine air filter is clogged.You may need to contact your installer for assistance if you can’t remedy these problems. Common causes for this condition include running the unit with all access doors removed, obstructed air inlet or exhaust port, low oil level, or debris in the engine cylinder cooling fins. To resolve the problem, remove any accumulated debris and obstructions and let the engine cool down. Ensure that the Oil Service door and/or the Control Panel door is installed whenever the unit is running. Low Frequency This fault is indicated by 5 blinks.This feature protects devices connected to the transfer switch by shutting the generator down if the engine runs slower than the preset limit. This condition is caused by a failed engine governor or by excessive loads on the generator.To remedy the problem, you may need to contact your installer or local service center for assistance. 15 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual GENERATOR MAINTENANCE CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. The generator warranty does not cover items that have been subjected to operator abuse or neglect.To receive full value from the warranty, the operator must maintain the system as instructed in the engine operator’s manual. • Refer to engine operator’s manual for oil fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. To fill your engine with oil: • Follow the synthetic oil grade recommendation and oil fill instructions given in the engine operator’s manual. All adjustments should be made at least once each season. Follow the requirements in the engine operator’s manual. Generator maintenance consists of keeping the unit clean. Operate the unit in an environment where it will not be exposed to excessive dust, dirt, moisture or any corrosive vapors. Cooling air louvers on the enclosure must not become clogged with snow, leaves, or any other foreign material. To Clean the Generator • Use a damp cloth to wipe exterior surfaces clean. CAUTION Improper treatment of generator can damage it and shorten its life. Check the cleanliness of the unit frequently and clean when dust, dirt, oil, moisture or other foreign substances are visible on its exterior/interior surface. • DO NOT expose generator to excessive moisture, dust, dirt, or corrosive vapors. • DO NOT insert any objects through cooling slots. NOTE: DO NOT use direct spray from a garden hose to clean generator.Water can enter the engine and generator and cause problems. • Use a soft, bristle brush to loosen caked on dirt, oil, etc. • Use a vacuum cleaner to pick up loose dirt and debris. • Use low pressure air (not to exceed 25 psi) to blow away dirt. Inspect cooling air slots and openings on the generator. These openings must be kept clean and unobstructed. Changing Engine Oil • Place the oil drain tube into an approved container. • Push in and rotate the oil drain fitting 1/4 turn counterclockwise. Slowly pull outward until oil starts draining (Figure 5). DO NOT pull the oil drain fitting off the engine. When Calling the Factory You must have the following information at hand if it is necessary to contact a local service center regarding service or repair of this unit: 1. Obtain the unit Model Number and Serial Number from the unit data decal. See “Know Your Backup Generator” diagram for location. 2. Obtain the engine Model/Type/Code numbers from the engine label. See “Know Your Backup Generator” diagram for location. Please note that the model number may vary slightly from that presented herein. Figure 5 — Oil Drain Fitting STORAGE The Briggs & Stratton Home Standby Generator is designed for continuous backup operational duty. As such, there is no need to take any storage precautions. However, if it becomes necessary to take the system out of service for an extended period, call Briggs and Stratton Technical Services at 1-800-743-4115, between 8:00 AM and 5:00 PM CT for specific recommendations. • When the oil has drained, push the oil drain fitting in and rotate 1/4 turn clockwise until it locks in place. • Slide the oil drain tube up into the clamp on the generator. 16 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual TROUBLESHOOTING Problem Engine is running, but no AC output is available. Engine runs good at no-load but "bogs down" when loads are connected. Cause Correction 1. Circuit breaker open or defective. 1. Reset or replace circuit breaker. 2. Fault in generator. 2. Contact local service facility. 3. Poor wiring connections or defective transfer switch. 3. Check and repair. 1. Short circuit in a connected load. 1. Disconnect shorted electrical load. 2. Generator is overloaded. 2. See "Essential Circuits". 3. Shorted generator circuit. 3. Contact local service facility. 4. Fuel Pressure is incorrect. 4. See "The Gaseous Fuel System" in the Installation Manual. 5. Natural gas fuel mixture is incorrect. 5. See "The Gaseous Fuel System" in the Installation Manual. 1. 15 Amp fuse missing or blown. 1. Install (new) 15 Amp fuse. See “Know Your System Control Panel”. Out of fuel. 2. Open fuel valve(s); check propane tank. 3. Failed battery. 3. Replace battery. 1. Out of fuel. 1. Check fuel valves, fill propane tank. 2. Fault indicator blinking. 2. Count blinks and refer to "Fault Detection System". 1. Generator circuit breaker is open. 1. Reset circuit breaker. 2. Transfer switch problems. 2. See the transfer switch manual. Engine will not start; or starts and runs rough. 2. Engine shuts down during operation. Loss of power on essential circuits. 17 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Briggs & Stratton Power Products Home Generator Operator’s Manual NOTES 18 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC EQUIPMENT OWNER WARRANTY POLICY Effective September 1, 2004 replaces all undated Warranties and all Warranties dated before September 1, 2004 LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.briggspowerproducts.com. THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country. OUR EQUIPMENT* OUTBOARD MOTOR PRESSURE WASHER WATER PUMP (Not available in the USA) PORTABLE GENERATOR WELDER HOME STANDBY GENERATOR SYSTEM Less than 10 KW 10 KW or greater Transfer switch WARRANTY PERIOD** Consumer Use Commercial Use * ** 2 years 1 year 1 year 2 years 2 years none 90 days 90 days 1 year none 3 years or 1500 hours none 3 years none The engine and starting batteries are warranted solely by the manufacturers of those products. 2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and Home Standby Generator System - Less than 10 KW, outside of European Union. The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty. Electric powered pressure washers used for commercial purposes are not warranted. NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD. ABOUT YOUR WARRANTY We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use and service. This warranty will not cover the following repairs and equipment: • Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover repair when normal use has exhausted the life of a part or the equipment. • Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.). • Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. This warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in life support applications. BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON, WI, USA www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario 20 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario CONSERVE ESTAS INSTRUCCIONES INSTRUCCIONES IMPORTANTES DE SEGURIDAD Fuego 21 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario PRECAUCIÓN ADVERTENCIA 22 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario CONSERVE ESTAS INSTRUCCIONES ORIENTACIÓN PARA EL PROPIETARIO 23 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario ADVERTENCIA ADVERTENCIA 2. 24 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario 25 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario • • • • • • • • • • • • • Manual del operario (P/N 192384GS) • • • • • • • • 26 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario Etiqueta del Motor 27 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario Contador de Horas Interruptor AUTO/OFF/MANUAL • • • 28 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario 3. 2. 3. 4. 1. tom ad ea ire a ert Pu te cei ea d cio rvi e s l de de la bat erí a 29 www.mymowerparts.com a ert Pu del l tro on c e el d pan Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario 5. 6. ANTES DEL ARRANQUE INICIAL Aceite de Motor PRECAUCIÓN PRECAUCIÓN • • 30 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario 2. 3. 1. 2. 3. 3. 4. 1. 2. 3. 4. 31 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario MANTENIMIENTO 1 2 3 4 5 6 7 Alta temperatura del aceite Presostato de Aceite Accesorio Adaptador para Drenaje de Aceite 32 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario • • 33 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario MANTENIMIENTO DEL GENERADOR • • • • Figura 10 — Adaptador de Vaciado de Aceite • • 1. 2. 34 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario Causa 1. 1. 2. 2. Consulte al servicio de Briggs & Stratton. 3. 3. 1. 1. 2. 2. 3. 3. Consulte al servicio de Briggs & Stratton. 4. 4. 5. 5. 1. 1. 2. No hay combustible. 2. 3. 3. 1. No hay combustible. 1. 2. 2. 1. 1. 2. 2. Consulte el manual del interruptor de transferencia. 35 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Generador Doméstico de Briggs & Stratton Power Products Manual del Operario NOTAS 36 www.mymowerparts.com NUESTRO EQUIPO* MOTOR FUERABORDA LIMPIADORA A PRESIÓN BOMBA DE AGUA GENERADOR PORTÁTIL SOLDADORA Menos de 10 kW 10 kW ó más SISTEMA DE GENERADOR DE RESERVA DOMÉSTICO PERÍODO DE GARANTÍA** Uso del consumidor 2 años 1 año 1 año 2 años 2 años 3 años Uso comercial ninguno 90 días 90 días 1 año ninguno ninguno ninguno * ** • • BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON, WI, EE.UU www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 38 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation VEUILLEZ CONSERVER CES INSTRUCTIONS DIRECTIVES DE SÉCURITÉ IMPORTANTES Symboles de Danger et Moyens Recul Pression Explosive Feu 39 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation AVERTISSEMENT 40 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation CONSERVEZ CES INSTRUCTIONS 41 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 2. 42 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 43 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation • • • • • • • • • • • Manuel d'installation (P/N 192385GS) • • • • • • • • • Pompe de piscine 44 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 45 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation Interrupteur AUTO/OFF/MANUAL • • 46 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 3. 2. 3. 2. 4. d'a ir de rte Po e er ed c i f i l'or ed 'ac cès de la bat ter ie u sd ccè a ' d rte Po 47 www.mymowerparts.com e nd ma m o c de eau l b ta Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 5. 6. AVANT LE DÉMARRAGE INITIAL ATTENTION • AVERTISSEMENT 48 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation FONCTIONNEMENT AUTOMATIQUE 3. ATTENTION 3. 4. 3. 2. 2. 3. 4. 49 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation 1 2 3 4 5 6 7 Thermocontact 50 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation Basse Tension • • 51 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation ENTRETIEN DU GÉNÉRATEUR • • • • • • REMISAGE ATTENTION 52 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation Cause Solution 1. 1. 2. 2. 3. 3. 1. 1. 2. 2. Voir "Circuits Essentiels". 3. 3. 4. 4. 5. 5. 1. 1. 2. 2. 3. 3. Remplacez la batterie. 1. 1. 2. 2. 1. 1. 2. 2. 53 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation REMARQUES 54 www.mymowerparts.com Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983 Groupe Électrogène de la Gamme de Produits Briggs & Stratton Manuel d'Utilisation REMARQUES 55 www.mymowerparts.com NOTRE ÉQUPEMENT* MOTEUR HORS-BORD NETTOYEUR À HAUTE PRESSION GÉNÉRATRICE PORTATIVE SYSTÈME DE GÉNÉRATRICE RÉSIDENTIELLE SOUDEUR 3 ans 2 ans 1 an 1 an 2 ans 2 ans aucune 90 jours 90 jours 1 an aucune * ** aucune • • BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON, WI, USA www.mymowerparts.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project