DSC LC 171 Instalační a uživatelská příručka

LC-171
Dual-Tech Motion Sensor
(Dual PIR & Microwave) with Pet
Immunity
INSTALLATION INSTRUCTIONS
&
USER MANUAL
P/N: 7131691 ver.F
1
1
General..................................................................................................................................................... 3
2
Features ................................................................................................................................................... 3
3
Assembly description ............................................................................................................................. 4
4
Detection Pattern .................................................................................................................................... 5
5
Selecting mounting location .................................................................................................................. 6
6
Detector Installation ............................................................................................................................... 7
7
Terminal Block Connections ................................................................................................................. 9
7.1
8
Wire Size Requirements ..................................................................................................... 9
Settings & Adjustments ....................................................................................................................... 10
8.1
Detection beam direction.................................................................................................. 10
8.2
Detection range setting .................................................................................................... 10
8.3
Sensitivity, Range and Pet immunity Adjustment ............................................................. 11
8.4
Indications setting............................................................................................................. 13
9
Operation ............................................................................................................................................... 14
10
Test procedure ...................................................................................................................................... 14
11
Specifications ........................................................................................................................................ 15
2
1
General
The LC-171 is unique motion detector utilizing four passive infra-red elements and
EN
Microwave technology for use outdoors and in harsh environments.
The LC-171 is designed for outdoor use in the most severe climatic conditions and may also
accommodate pets.
High reliability is achieved by combining both dual tech hardware with highly sophisticated
software and an adaptive coverage area, greatly reducing the possibility of false alarms.
The active elements are comprised of a dual PIR and advanced Microwave detector inside a
stylish, rigid plastic body.
This special optics combined with state of the art microwave Doppler sensor assures elimination
of “false alarms” while maintaining high security standards for the detection of human intruders
into the protected area.
The detection sensitivity and range is controlled by a digital rotary switch allowing 16 calibration
levels, so that the correct detection pattern will be set for every installation.
The LC-171 is designed to protect large areas and can easily be installed on walls or poles in
order to provide a solid area of protection while rejecting interference from birds and small
animals due to the provided pet immunity optics.
2
Features
• Microwave detection based on Doppler concept.
• N.O. & N. C. Relays switched at the same time.
• Pet immunity up 35kg (77 lb.)
• 16 levels of PIR sensitivity adjustment and 3 microwave sensitivity groups.
• Temperature compensation.
• Microcontroller signal processing.
• Front and back tamper protection.
• Audible indication of walk test and intruder detection.
• Unique waterproof sealed plastic design.
• Detection Range: Up to 12m (39ft.)
• Detect human intruders walking or running.
• No maintenance required.
• High RFI/EMI Immunity.
• Protection from: direct sunlight, wind up to 30 m/sec (98 ft/sec), snow and rain, small animals,
removal of the top cover and removal from mounting bracket
3
3
Assembly description
The LC-171 is a robust detector which includes a large LED indicator that can be easily observed
from long distances and an optional buzzer to provide indication of intrusion.
Using the supplied mounting bracket, the LC-171 can be easily mounted to walls using mounting
screws and poles using the supplied metal bands.
The LC-171 is combined of three detection elements:
•
Upper PIR element
•
Lower PIR element
•
Microwave element
•
The upper PIR element has an adjustable detection height while the other two are fixed.
The following drawing shows all internal elements:
Terminal Connection Blocks
LED
Range Indication
Range setting handle
Upper PIR element
Tamper switch
LED and Buzzer dipswitches
Lower PIR element
Sensitivity setting
Microwave element
Direction Angle Indicator
Bracket locking screw
4
4
Detection Pattern
The LC-171 has a 90° top view PIR and MW detection pattern with over 12m (39 ft.)
EN
detection distance (when installed at 1.2m (4 ft.) above the ground surface).
The LC-171 has an internal rotating housing (which includes the 2 PIR elements and the MW)
that can be adjusted horizontally, so its 90° coverage may vary between 0° and 180°.
Detection area
Microwave detection pattern
No Detection
Detection
Lower PIR element detection pattern
Fixed to 12m range
No pet detection in all
protected area
Upper PIR element detection pattern
Adjustable between 3m and 12m (10ft to 39ft)
The LC-171 can differentiate between pets and human bodies and alert accordingly by
having microwave movement detection combined with two PIR detection beams:.
A. Lower PIR element which is fixed to 12m (39ft.) range and 60cm (2ft) above ground level
which helps avoiding pet detection over the entire area.
B. Upper PIR element which has adaptive range between 3 and 12m (10 and 39 ft).
An intrusion is defined by both PIR detection beams being crossed and a Microwave detection
occurring, causing an alarm.
No alarm will be generated if only one of the PIR detection beams is crossed and microwave
detection occurs.
5
5
Selecting mounting location
The installation of the LC-171 requires a solid, level base for the mounting bracket and must be
located in a manner that when the detector is mounted, it is facing the center of the desired
detection zone.
It is recommended that the detector will face
a solid border limiting the detection area, such as the
building structure or fencing wall, to avoid undesired detection
range.
The protected area must be free from obstacles like walls,
fences, trees, ditches and other microwave detectors.
Choose a location most likely to intercept an intruder according to detection pattern on page 5.
Avoid the Following Installation Locations:
• Facing direct sunlight.
• Facing areas subject to rapid temperature changes.
• Mounted at more than 10º from the vertical or horizontal plane.
• Facing metal doors.
• Near direct sources of heat or airflow.
• Clear all physical obstacles from the detection area
(e.g. plants, laundry, etc.)
• Clear all light reflecting surfaces from the detection area,
including puddles or other standing water.
• Avoid installation on the following types of ground:
Thick vegetation, Grass (un-mown), Water, Sand and Metal.
NOTES:
• Recommended installation height is 1.2m (4ft).
• The DUAL (Four Elements) high quality sensor detects motion crossing the beam; it is less
sensitive detecting motion towards the detector.
• The LC-171 performs best when provided with a constant and stable environment.
• In order to ensure suitable operation of the LC-171 type of ground should be one of the
following: Asphalt concrete, Cement, Soil, Clay, Gravel or Grass (mown).
• Sensitivity adjustment may be required upon extreme temperature changes.
Extremely high temperature will reduce detection range.
Extremely low temperature will increase detection range.
Choose proper installation location to avoid resetting.
6
6
Detector Installation
Important! Prior to installation, read both “Operation” and “Selecting the mounting
EN
location” sections carefully.
1. Install the detector in such manner that the intruder
2. The detector is to be installed at height of 0.8 to 1.5
is most likely to cross the detection area from side to
meter (2.6 to 4.9 ft.), ideally 1.2m (4 ft.)
side.
3. Make sure to attach the metal bracket to a leveled
4. Rotating the detection beam may be required for
straight and firm wall, leaving 15cm (5.9 inches) from
guarding a side window opening while the detector is
the top and 15cm from both sides, for easy installation
installed facing another direction.
and maintenance.
5. Open the detector unwinding the bottom screw.
6. Release the rear metal bracket by unwinding
internal bottom screw.
7. Release the detector body from the metal bracket
8. Attach the rear bracket to the wall or a pole using
by pulling the detector out and up.
mounting screws or metal bands.
7
9. Break the relevant knockouts on the rear side of the
10. Attach the sealing “U” shaped Sponge Pad to the
plastic base and slide the wires from the outside via the
wire opening from the rear side after the wires have
paths and knockout to the internal side of the detector.
been connected and prior to final product affixing to
the mounted bracket.
11. Place the detector on the mounting bracket from top
12. Connect the wires to the terminal blocks
side down and then lock the screw at the bottom.
according to the following chapter.
8
7
Terminal Block Connections
EN
Terminal 1 - Marked “-” (GND) - Connect to the ground of the Control Panel.
Terminal 2 - Marked “+” (+12V) - Connect to a positive Voltage of 9.6 -16Vdc source of the
Control Panel.
Terminals 3 & 4 - Marked “TAMP” - If a Tamper function is required connect these
Terminals to a normally closed 24-Hour Tamper Zone on the Control Panel.
If the top cover of the detector is opened or the detector is detached from installation wall, an
immediate alarm signal will be sent to the Control Panel.
Terminal 5 - Marked “EOL” - End of line – optional terminal for end of line resistors
connections.
Terminals 6, 7 & 8 - Marked “NC / C / NO” - These are the output relay contacts of the
detector. Connect to a zone input on the control unit. When an intruder is detected, alarm
relays (N.C. and N.O.) will switch for 1.8 sec.
7.1 Wire Size Requirements
Use #22 AWG or larger wires. Use the following table to determine required wire gauge and
length.
Wire Length [m]
250
350
600
1000
Wire Length [ft.]
800
1200
2000
3400
Wire Gauge [#]
22
20
18
16
9
8
Settings & Adjustments
8.1 Detection beam direction
The LC-171 detection beam direction may vary between 0º and 180º.
In order to change the detection beam direction rotate the internal detection element
housing to the desired direction.
8.2 Detection range setting
The LC-171 detection range may vary between 3m (10 ft) and 12m (39 ft), while installed on
1.2m (4 ft.) height above the ground surface.
Changing the detection range is achieved by sliding the upper detection element up or
down.
10
EN
To adjust for ranges between 3m and 12m (10 and 39 ft.) slide the detection element up or
down to correspond with the desired distance. Each step between 3m and 12m (10 and
39ft.) represents 3m (10ft) of range.
Maximum Range (12m, 39ft)
Minimum Range (3m, 10ft)
8.3 Sensitivity, Range and Pet immunity Adjustment
The calibration of range and sensitivity is performed by a single 16 position rotating switch.
There are 3 groups of switch settings grouped according to desired detection range.
Each group is divided into several levels of sensitivity according to the installation
environment.
The sensitivity is determined by a single 16 position rotating switch. Changing the
sensitivity affects immunity to environmental noises, and also affects the detection distance
and pet immunity level.
The rotating switch is marked with digits from “0” to “9” and following letters from “A” to “F”.
Position “0” is maximum sensitivity and “F” is minimum sensitivity.
Note: Adjust sensitivity according to environmental conditions!
Group A - positions 0 – 5 – set sensitivity for 12m detection range with immunity to pets weight
up to 20kg
Group B - positions 6 – A – set sensitivity for 10m detection range with immunity to pets weight
up to 35kg
Group C - positions B – F – set sensitivity for 7m detection range with immunity to pets weight
up to 35kg
NOTE: Ensure that you select the group with a range corresponding to or slightly higher then
the range set in 8.2. Do not select a group setting that has a lower range then the range set in
8.2.
11
Low Risk
Noisy Area
Very High Risk
High Risk
Risk
F
7m
(23 ft)
with Pet
Immune
up to
35kg
(77 lb)
0
12m
(39 ft)
with Pet
Immune
up to
20kg
(44 lb)
1
E
2
D
3
Risk
High Risk
Very High Risk
Noisy Area
C
4
Extremely Noisy Area
B
Low Risk
5
A
6
9
8
7
Low Risk
10m
(33 ft)
with Pet
Immune
up to
35kg
(77 lb)
Risk
High Risk
Very High Risk
Noisy Area
Each group is divided to 5 or 6 sub-positions that help to define the environmental
condition inside the detection range:
•
Low risk: very stable environment without interference from parking garages, parking
spaces, playgrounds, football fields, service roads, etc.
•
Risk: Stable environment with some trees, bushes, flowerpots, planters.
•
High risk: Unstable environment with different types of vegetation and grass and
puddles.
•
Very high risk: Unstable environment with winds and small pets, rats, mice, birds.
•
Noisy area: Unstable environment with vegetation and water sources like swimming
pool, lake, canal, weeds as well as small pets like cats and rabbits.
•
Extremely Noisy area: Very unstable environment subject to wind, snow, rain, with
vegetation, water and large pets, such as dogs.
For example:
If detector is used for 10m (33 ft) range in open space with sunlight and pets, set switch to
position 9.
12
8.4 Indications setting
EN
ON
LED OFF
OFF
Buzzer ON
Factory default setting
Factory default setting
The LC-171 has two types of indicators:
1. LED
2. Buzzer
The installer can adjust both indicators operation during detection (ON or OFF) by using
switch number “1” for the buzzer and switch number “2” for the LED. When the LED indicator
is ON the LED indicator will activate for 1 second each time an intrusion is detected. When the
LED indicator is OFF the LED will not be used to indicate an intrusion has occurred.
When the Buzzer indicator is ON the Buzzer will activate for 1.8sec each time an intrusion is
detected. When the Buzzer indicator is OFF the buzzer will not be used to indicate an intrusion
has occurred. (Setting the buzzer ON gives the installer the ability to have audible
confirmation of intrusion detection during the adjustments and a walk test. After completing
adjustments and walk testing it is recommended to switch the buzzer OFF)
•
Place the top cover to the base and close it using the bottom screw.
13
9
Operation
Note!
Connect the LC-171 to a positive Voltage output of 9.6 -16Vdc source.
Use only a listed power limited source.
The detector shall be provided with minimum of 4 hours of standby power from either a
listed compatible control unit or power supply.
The detector begins a 2 minute warm up period once connected to power.
The LED will flash for the first 30 seconds of the warm up period after power up. The device
is operational once the LED stops flashing.
The warm up period will continue for 90 seconds after the LED stops flashing.
Once the warm up period is complete the device is ready for use.
10 Test procedure
Walk Test
IMPORTANT NOTE: Once installed, the unit should be thoroughly tested to verify proper
operation and coverage. After installation, the unit should be tested annually by the installer. The
end user should be instructed on how to perform a weekly walk test.
Ensure that the detector has completed the 2 minute warm up period before walk testing
Make sure that the protected area is cleared of all people.
Create motion in the entire area where coverage is desired by walking perpendicular to the
detection pattern.
Listen to ALARM sound whenever motion is detected (the red LED also turns ON whenever
motion is detected).
Allow 5 sec. between each test for the detector to stabilize.
Walk across the entire area where coverage is desired. Should the coverage be incomplete,
readjust coverage range or relocate the detector.
Once coverage is as desired, the buzzer and LED should be disabled.
14
11 Specifications
Detection Method
Microwave Frequency
Power Input
Current Draw
Temp Compensation
Alarm Period
Alarm Outputs
Tamper Switch(s)
Warm up Period
LED Indicator
RF Immunity
ElectroStatic Immunity
Transient Immunity
Operation Temp
Dimensions
Weight
European directives
European standards
requirements:
USA & Canada
Protection Degree
•
EN
Dual PIR AND MW
24.125 GHz
9.6 to 16Vdc
Active: 24mA (±5%)
Standby: 21mA (±5%)
Yes, Dual slope temperature compensation
2 sec (±0.5sec)
Form C (NC, NO, Common)
28Vdc 0.1 A with 10 Ohm series protection resistor
Two Switches
N.C 28Vdc 0.1 A with 10 Ohm Series protection resistors
Opens when cover is removed from unit’s base or if base is removed from
wall
120sec (± 5sec)
LED is ON during ALARM (configurable)
10 V/m plus 80% AM from 80 MHz to 2GHz
6kV contact, 8kV air
1kV
-35ºC ~ +55ºC (-31°F ~ +131°F)
200mm x 86mm x 80mm (7.8" x 3.4" x 3.2")
500gr. (1.1 lb)
RTTE directive:1999/5/EC
EMC directive: 2004/108/EC
Low Voltage directive: 2006/95/EC
RoHS directive: 2002/95/EC
EN300 440-2; EN301 489-1; EN50130-4 +A1 +A2; EN61000-6-3+A11
EN60950-1
EN50131-1 / EN50131-2-4 / EN50130-5
47CFR part 15, subpart C, section 15.245; 47CFR part 15, subpart B
RSS210; ICES-003
IEC 60529: IP 65
Specifications are subject to change without prior notice.
FCC COMPLIANCE STATEMENT
FCC ID: F5309LC171
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not
installed and used properly, in strict accordance with the manufacturer’s
instructions, may cause interference to radio and television reception. It
has been type tested and found to comply with the limits for Class B
device in accordance with the specifications in Subpart "B" of Part 15 of
FCC Rules, which are designed to provide reasonable protection against
such interference in any residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause interference to television or radio reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
· Re-orient the receiving antenna
· Relocate the alarm control with respect to the receiver
· Move the alarm control away from the receiver
· Connect the alarm control into a different outlet so that alarm control
and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user may find
the following booklet prepared by the FCC helpful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is
available from the U.S. Government Printing Office, Washington, D.C.
20402, Stock # 004-000-00345-4.
INDUSTRY CANADA COMPLIANCE STATEMENT
IC:160A-LC171
The term ‘IC:’ before the radio certification number only signifies that
Industry Canada technical specifications were met.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
15
RTTE Compliance Statement:
Limited Warranty
Digital Security Controls warrants that for a period of 12 months from the date of purchase, the
product shall be free of defects in materials and workmanship under normal use and that in fulfillment
of any breach of such warranty, Digital Security Controls shall, at its option, repair or replace the
defective equipment upon return of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or handling, or damage
due to causes beyond the control of Digital Security Controls such as lightning, excessive voltage,
mechanical shock, water damage, or damage arising out of abuse, alteration or improper application
of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all
other warranties, whether expressed or implied and of all other obligations or liabilities on the part of
Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes
any other person purporting to act on its behalf to modify or to change this warranty, nor to assume
for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages,
loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product.
Motion detectors can only detect motion within the designated areas as shown in their respective
installation instructions. They cannot discriminate between intruders and intended occupants. Motion
detectors do not provide volumetric area protection. They have multiple beams of detection and
motion can only be detected in unobstructed areas covered by these beams. They cannot detect
motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or
windows. Any type of tampering whether intentional or unintentional such as masking, painting, or
spraying of any material on the lenses, mirrors, windows or any other part of the detection system will
impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their
effectiveness can be reduced when the ambient temperature rises near or above body temperature
or if there are intentional or unintentional sources of heat in or near the detection area. Some of these
heat sources could be heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam vents,
lighting and so on.
Warning: Digital Security Controls recommends that the entire system be completely tested
on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product to fail to perform as
expected.
Important Information: Changes or modifications not expressly approved by Digital Security
Controls could void the user’s authority to operate this equipment.
16
LC-171
FR
17
1
2
3
4
5
6
7
8
8.2
8.3
8.4
9
10
11
18
FR
•
•
Élément micro-onde
•
Élément micro-onde
FR
21
FR
23
en bas.
24
FR
250
350
600
1000
800
1200
2000
3400
22
20
18
16
25
26
Portée minimum (3 m, 10 pi)
F
0
1
2
3
4
B
5
A
6
9
8
7
•
•
•
•
•
28
FR
MARCHE
ARRÊT
•
29
30
FR
31
32
33
1
General................................................................................................................................................... 35
2
3
4
5
6
7
8
8.2
8.3
8.4
9
10
11
34
ES
35
•
Elemento PIR inferior
•
Elemento de microondas
•
Elemento PIR inferior
ES
37
0,8-1,5 metros
mantenimiento.
6. Suelte el soporte de metal trasero destornillando el
tornillo inferior interno.
39
40
250
350
600
1000
800
1200
2000
3400
22
20
18
16
41
Haz recta
42
Alcance máximo (12 m)
7 m con
F
a7m
animales
Riesgo
muyRisk
alto domésticos
with Pet
Very High
hasta
Immune
Riesgo alto con
upKg
to
High Risk 35
Riesgo
0
12 m con Bajo
Lowriesgo
Risk
inmunidad a
animales
Riesgo
Risk
18m
domésticos
con
hasta
with
Pet
Alto
riesgo
20
Kg
Immune
High
Risk
1
E
D
3
35kg
Risk
up to
20kg
2
Very High Risk
Área de ruido
Noisy Area
C
Bajo riesgo
4
B
Low Risk
5
A
Área
de
Extremely
Noisy Area
ruido
extremo
6
9
8
7
10 m con
inmunidad a
13m
animales
with Pet
domésticos
conImmune
hasta
35 up
Kg to
35kg
Bajo
riesgo
Low Risk
Riesgo
Risk
Alto
Highriesgo
Risk
Riesgo
muy
alto
Very High
Risk
Noisyde
Area
Área
ruido
•
•
•
•
•
44
LED DESACTIVADO
ON
OFF
Chicharra
ACTIVADA
ES
•
45
46
47
48
49
PR
1
Geral ....................................................................................................................................................... 51
2
3
4
5
6
7
8
8.2
8.3
8.4
9
10
11
50
PR
51
•
•
Elemento de microondas
•
Elemento PIR inferior
53
outro.
0,8-1,5 metros
proteger uma abertura de janela lateral enquanto o
55
56
PR
250
350
600
1000
800
1200
2000
3400
22
20
18
16
57
58
Alcance máximo (12 m)
7 m com
F
a7m
animais
Risco
alto domésticos
with Pet
Verymuito
High Risk
até
Immune
Risco alto de
upkg
to
High Risk 35
Risco
0
1
E
D
3
35kg
Risk
up to
20kg
2
4
B
Low Risk
Very High Risk
C
5
A
6
9
8
7
35kg
Baixo
risco
Low Risk
Risco
Risk
Alto
Highrisco
Risk
Risco
muito
alto
Very High
Risk
•
•
•
•
•
60
LED DESACTIVADO
PR
•
Coloque a tampa superior na base e feche-a utilizando o parafuso inferior.
61
62
63
64
65
IT
1
Generale ................................................................................................................................................ 67
2
3
4
5
6
7
7.1
8
8.1
8.2
8.3
8.4
9
10
11
Specifiche .............................................................................................................................................. 79
66
IT
Elemento PIR superiore
•
•
•
69
71
parte posteriore.
72
IT
250
350
600
1000
800
1200
2000
3400
22
20
18
16
73
74
Range massimo (12 m)
Range minimo (3 m)
IT
75
•
•
•
•
•
76
ON
LED OFF
OFF
IT
•
77
Nota!
78
79
80">