Velleman KNS6 Manual

KNS6 – TRAINMECH
1. Introduction & Characteristics
Thank you for buying the KNS6 ! Read this manual carefully before bringing the KNS6 into use.
• Familiarise yourself with the operation of transmissions steered through gears or pulleys.
• Easy to build, no glue or soldering required.
• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper
included)
• The kit is powered by 2 AA-batteries (not included).
The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a
battery holder and all necessary parts.
Note that the figures with the assembly instructions can be found in the second folder “KNS6 – Figures”!!!
Quant.
1
1
1
1
1
1
5
1
1
1
1
1
1
1
2
2
Description
gearbox
battery holder
motor DC 6V
slide switch with wire
metal shaft (2 x 40mm)
metal shaft (3 x 52mm)
metal shaft (2 x 60mm)
pinion gear 10T (white)
face gear (36T/14T)
gear 36T/0T
gear (36T/14T)
gear (36T/14T)
wire with terminal (yellow)
wire with terminal (green)
belt (40 x 1.2mm)
pulley (15 x 2.9mm)
Part n°
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Quant.
2
2
8
3
8
4
2
2
8
32
2
10
10
10
8
13
Description
pulley (15 x 1.9mm)
nylon post (H = 6mm)
nylon post (H = 3mm)
PVC tube (15 x 1.5mm)
nut M3
screw (3 x 12mm)
screw (3 x 16mm)
screw (3 x 20mm)
washer (3.2 x 10 x 0.5mm)
self-tapping screw (2 x 4mm)
self-tapping screw (2 x 6mm)
nylon pad (5.6 x 4.8 x 1.95mm)
nylon pad (Ø8mm)
nylon pad (6.6 x 4.8 x 2.1mm)
nylon connector (N-shaped)
fixing plate (L-shaped)
3. Prepunched Boards (see “KNS6 – Figures”)
4. Assembly (see also “KNS6 – Figures”)
Fig. 3 : The gears (n°9/10/11/12) should be placed to the left of the pinion gear (n°8). Note that the protruding
edge should point towards the metal case.
Fig. 4 : Screw 1 x piece n°32 on boards 1 & 2 and attach them to boards n°3 & 4.
KNS6
1
Fig. 9 : Note that the wires of the battery holder (n°3) should run next to the switch (n°4). Consult fig. 16 in the
second folder “KNS6 – Figures” for the wiring.
Fig. 10 : Insert the batteries before screwing board n°9 into place.
Fig. 11 : Insert 10 x piece n°30 in boards 1 & 2. Insert 8 x piece n°28 in the eight wheels. Use 5 metal shafts (n°7)
to link the wheels on both sides of the train. Verify whether the wheels can move freely.
Fig. 12 : Fit the two pulleys with a belt (n°15).
Fig. 13 : Fit the three shafts in figure 13 with a nylon post (n°19). Apply connector n°31 and the other parts
according to the figure.
Fig. 14 : The 4 N-shaped nylon connectors (n°31) on the left wheels should form a 90° angle with the right wheels.
In other words, the connectors must be positioned vertically on one side when they are positioned
horizontally on the other side.
5. Attention
• Make sure the wiring is correct
• Note that the shafts should be able to move freely.
Hoev.
1
1
1
1
1
Nr.
17
18
19
20
21
2
Hoev.
2
2
8
3
8
6
7
8
9
10
11
12
13
14
15
16
1
5
1
1
1
1
1
1
1
2
2
metalen as (3 x 52mm)
metalen as (2 x 60mm)
rondsel 10T (wit)
tandwiel (36T/14T)
tandwiel 36T/0T
tandwiel (36T/14T)
tandwiel (36T/14T)
draad met connector (geel)
draad met connector (groen)
riem (40 x 1.2mm)
katrol (15 x 2.9mm)
22
23
24
25
26
27
28
29
30
31
32
4
2
2
8
32
2
10
10
10
8
13
KNS6
3
Quant.
1
1
1
1
1
1
5
1
1
Pièce
17
18
19
20
21
22
23
24
25
Quant.
2
2
8
3
8
4
2
2
8
10
11
12
13
14
15
16
1
1
1
1
1
2
2
26
27
28
29
30
31
32
32
2
10
10
10
8
13
4
Anzahl
1
1
Nr.
17
18
5
Anzahl
2
2
3
4
5
6
7
8
9
10
1
1
1
1
5
1
1
1
19
20
21
22
23
24
25
26
8
3
8
4
2
2
8
32
11
1
Zahnrad (36T/14T)
27
2
12
13
14
15
16
1
1
1
2
2
28
29
30
31
32
10
10
10
8
13
6
2. Lista de piezas
N°
pieza
1
2
3
4
5
6
7
8
9
Cantidad
1
1
1
1
1
1
5
1
1
Pieza
17
18
19
20
21
22
23
24
25
Cantidad
2
2
8
3
8
4
2
2
8
10
11
12
13
14
15
16
1
1
1
1
1
2
2
26
27
28
29
30
31
32
32
2
10
10
10
8
13
KNS6
7
KNS6
8