Chief 100013091, LTA5045, LTA5029, LSA5045, LTA5536, INF-WALLMNT2, LTA5051, LSA5536, LSA5029 Data Sheet

INSTALLATION INSTRUCTIONS
ИНСТРУКЦИИ ПО УСТАНОВКЕ
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
LSA
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
LTA
FUSION LARGE FLAT PANEL MOUNTS
LSA/LTA Series
LSA/LTA Series
Installation Instructions
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
2
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the LSA/LTA up to (and
including) the display does not exceed 200 lbs (90.7 kg).
Installation Instructions
LSA/LTA Series
DIMENSIONS
LSA
NOTES:
1. MAX MOUNTING PATTERN IS 31.8"[807.7mm] WITHOUT REVERSING UPRIGHTS.
2. MAX MOUNTING PATTERN IS 34.3"[871.2mm] WITH REVERSING UPRIGHTS.
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .56"[14.2mm].
4. MOUNT RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET APPLICATIONS.
MOUNT IS 1.96"[49.8mm] DEEP WHEN FLAT TO WALL.
.32 8.1
1.00 25.4
.87 22.1
1.96 49.8
1.52 38.5
.59 15.1
.57 14.4
MINIMUM UPRIGHT
SPACING IS 12"
13.23 336
1.44 36.6
12.00 304.8
21.28 540.4
8.86
8.37 212.5
7.87 200
7.38 187.5
6.89 175
6.40 162.5
5.91 150
5.41 137.5
4.92 125
4.43 112.5
3.94 100
3.44 87.5
2.95 75
2.46 62.5
1.97 50
1.48 37.5
.98 25
.49 12.5
0
.49 12.5
3.44 87.5
2.19 55.7
8.37 212.5
9.97 253.2
DIMENSION: [MILLIMETERS]
INCHES
34.57 878.1
LTA
NOTES:
MAX MOUNTING PATTERN IS 30.6" (777.2 mm) WITHOUT REVERSING UPRIGHTS.
.32 8.1
.53 13.5
1.00 25.4
2.00 50.8
5.29 134.5
.57 14.4
MINIMUM UPRIGHT
SPACING IS 12"
5.91
5.41 137.5
4.92 125
4.43 112.5
3.94 100
3.44 87.5
2.95 75
2.46 62.5
1.97 50
1.48 37.5
.98 25
.49 12.5
12°
1.00 25.4
.34 8.6
21.00 533.4
1.44 36.6
12.00 304.8
0
7.00 177.8
20.54 521.7
13.23 336
2.18 55.3
RAILS CAN BE SLID LEFT
OR RIGHT FOR OFFSET
.93 23.6
34.53 877.1
DIMENSION: [MILLIMETERS]
INCHES
3
Installation Instructions
LSA/LTA Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Einstellen
Chave de fendas Phillips
Ajustar
Cacciavite a stella
Regolare
Kruiskopschroevendraaier
Afstellen
Tournevis à pointe cruciforme
Ajuster
Open-Ended Wrench
Remove
Llave de boca
Quitar
Gabelschlüssel
Entfernen
Chave de bocas
Remover
Chiave a punte aperte
Rimuovere
Steeksleutel
Verwijderen
Clé à fourche
Retirez
By Hand
Optional
A mano
Opcional
Von Hand
Optional
Com a mão
Opcional
A mano
Opzionale
Met de hand
Optie
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Llave de seguridad
Sechskantschlüssel
Sicherheitsschlüssel
Chave de cabeça sextavada
Chave de segurança
Chiave esagonale
Chiave di sicurezza
Zeskantsleutel
Veiligheidssleutel
Clé à tête hexagonale
Clé de sécurité
4
LSA/LTA Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
M5
(included)
7/32" (5.5mm) Wood Stud
5/16" (7.9mm) Concrete
PARTS
[A-N used on LSAU/LTAU Models Only]
[Included with
LSA2XXX/LTA2XXX
Models Only]
Custom
LSA2XXX/
LTA2XXX
Hardware
A (8)
M4x16mm
B (6)
M4x20mm
C (6)
M4x25mm
D (6)
M5x16mm
E (6)
M5x20mm
F (6)
M5x25mm
G (6)
M6x16mm
H (6)
M6x25mm
J (6)
M8x30mm
I (6)
M8x20mm
L (8)
.750x.323x.250
R (1)
M (8)
.750x.344x.500
K (4)
M8x50mm
P (1)
M5
N (8)
S (1)
(LTA Only)
T (1)
(LSA Only)
U (1)
W (1)
QA (4)
5/16"
QB (4)
5/16"
QC (4)
5/16" x 2-1/2"
V (1)
(LSA Only)
5
X (1)
(LTA Only)
LSA/LTA Series
Installation Instructions
INSTALLATION
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
The LTA and LSA have been designed to be mounted directly
onto either a wood stud or concrete wall. The LTA has brackets
which allow the TV to be tilted. The LSA has static brackets
which keep the TV in an upright position.
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
Locate Mounting Site
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the weight of the LTA or LSA and all attached equipment not
to exceed 200 lbs (90.7 kg).
NOTE: Proceed to either the Installing to a Wood Stud Wall
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
6.
Drill one 7/32" (5.5mm) pilot hole in each stud.
7.
Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat
washers (QB) to attach top of mount to wall. (See Figure 2)
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1.
Determine the center of the TV screen, and where it should
be located on the wall.
2.
Locate the closest stud to the left and right of the selected
location.
5
6
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3.
Line up the diamond on mount with center of screen
marking to determine vertical center. (See Figure 1)
4.
Measure up 6" from the center point to mark location of the
upper mounting slots.
7
10
Center of screen
6"
(152.4mm)
(QC) x 4
8
9
(QB) x 4
Figure 2
8.
Vertical center
of mount
Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
9. Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 2)
10. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat
washers (QB) to attach the mount to the wall through the
lower mounting holes. (See Figure 2)
11. Slide rails to approximate center of screen location.
Installing to a Concrete Wall
Figure 1
5.
6
Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
1.
Determine the center of the TV screen, and where it should
be located on the wall.
Installation Instructions
LSA/LTA Series
2.
Line up the diamonds on mount with center of screen
marking to determine vertical center. (See Figure 1)
9.
Drill one 5/16" (7.9mm) pilot hole at each marking for lower
mounting holes. (See Figure 3)
3.
Measure up 6" (152.4mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
10. Install an anchor (QA) into each pilot hole using a hammer.
4.
Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
11. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat
washers (QB) to attach the mount to the wall through the
lower mounting holes. (See Figure 3)
12. Slide rails to approximate center of screen location.
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 12" (304.8mm). Do not
place mounting brackets closer together than 12" (304.8mm).
Attaching Interface Brackets to TV
1.
Align the center of the bracket with center of screen.
(See Figure 4)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
6 10
(QA) x 4
4
8
5
9
Pull strap
x4
Center of bracket
Figure 4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2.
7 11
Select correct screws, spacers (if necessary) and universal
washers from the hardware bag (A-N) and attach brackets
to back of screen. (See Figure 4)
(QB) x 4
(QC) x 4
Figure 3
5.
Drill one 5/16" (7.9mm) pilot hole at each marking.
6.
Install an anchor (QA) into each pilot hole using a hammer.
7.
Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat
washers (QB) to attach top of mount to anchors in wall.
8.
Mark the attachment points for the lower mounting slots.
(See Figure 3)
7
LSA/LTA Series
Installation Instructions
Switching Interface Brackets (Optional)
If an installation situation makes adjusting the location of
interface brackets necessary, there are several options.
1.
The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 5)
2.
The location of the left and right interface brackets may be
switched, with the knobs on the LTA interface brackets
facing the inside of the mount. (See Figure 5)
3d
3e
1
Knobs
Knobs to outside
of brackets
Figure 6
Attaching Screen to Wall Mount
1.
Adjust Velcro® pull strap (if necessary) so it does not extend
beyond bottom of screen. (See Figure 7)
NOTE: Do NOT allow both interface brackets to be located on
same side of wall bracket. (See Figure 7)
NOTE: NEVER place both interface brackets to one side of the
2
Figure 5
3.
If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets to be reversed.
(See Figure 6)
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
d. Remove the knob, washer and screw.
e. Replace the knob, washer and screw in the opposite
order, with the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
8
wall mount center line! (See Figure 7)
Installation Instructions
LSA/LTA Series
Center Line (CL)
2
Top
Hook
Pullstrap
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Pullstrap
5
(Screen not shown for clarity)
Both interface brackets must NEVER be located
to one side of the wall brackets!
Figure 7
2.
Hang top hook of interface brackets onto the top bar of the
mount. (See Figure 8)
NOTE: The screen initially installs into the "kickstand mode" to
Figure 8
Locking Mount (Optional)
1.
Add optional security bracket (S or T) to the mount. (See
Figure 9)
2.
Add padlock (not included) to complete security.
allow easy cable access.
3.
Slide screen and bars to desired viewing position.
4.
Route cables between wall and bars.
(S)
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
5.
2
1
Pull downward on the pullstraps and swing inward toward
wall, latching interface brackets to lower bar and locking
bottom of screen to the mount. (See Figure 8)
(LTA Shown)
Figure 9
9
LSA/LTA Series
10
Installation Instructions
Installation Instructions
LSA/LTA Series
11
LSA/LTA Series
Installation Instructions
USA/International
Europe
Chief Manufacturing, a products division
of Milestone AV Technologies
8831-000023 Rev03
©2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
02/11
Asia Pacific
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
A
P
F
A
P
F
A
ИНСТРУКЦИИ ПО УСТАНОВКЕ
Instrucciones de instalacin
Installationsanleitung
Instrues de Instalao
LSA
Istruzioni di installazione
Installatie-instructies
Instructions dinstallation
LTA
Серия LSA/LTA
Серия LSA/LTA
14
Серия LSA/LTA
,.32 8.1
,
,
1.00
25.4
,
,
,
1.52
38.5
,
,.87 22.1
,
,
1.96
49.8
,.59 15.1
,
,
,.57 14.4
МИНИМАЛЬНЫЙ
ЗАЗОР МЕЖДУ [304,8]
MINIMUM UPRIGHT
НАСТЕННЫМИ
КРОНШТЕЙНАМИ
12
SPACING IS 12"
,
13.23
336
1.44
36.6
,
,
LSA
1. MAX
MOUNTING
IS 31.8"[807.7mm]
WITHOUT
UPRIGHTS.
4. МОНТАЖНЫЕ
РЕЙКИ
МОЖНОPATTERN
СДВИНУТЬ
ВЛЕВО ИЛИ ВПРАВО
ДЛЯREVERSING
СДВИГАЕМЫХ
2. MAX MOUNTING PATTERN IS 34.3"[871.2mm] WITH REVERSING UPRIGHTS.
КРЕПЛЕНИЙ.
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
IS .56"[14.2mm].
5. КРОНШТЕЙНENGAGEMENT
ГЛУБИНОЙ 49,8MM
(1,96”) ДЛЯ ПЛОСКОГО КРЕПЛЕНИЯ К СТЕНЕ.
4. MOUNT RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET APPLICATIONS.
MOUNT IS 1.96"[49.8mm] DEEP WHEN FLAT TO WALL.
,
,
12.00
304.8
,
,
21.28
540.4
,
,
,
,
,
8.86
,
,
212.5
8.37
,
7.87
200
,
,
187.5
7.38
,
6.89
175
,
,
162.5
6.40
,
5.91 150
,
,
137.5
5.41
,
4.92
125
,
,
112.5
4.43
,
3.94
100
,
,
87.5
3.44
,
2.95
75
,
,
62.5
2.46
,
1.97
50
,
,
37.5
1.48
,
.98
25
,.49 12.5
,
0
,
,
.49
12.5
,
,
,
,
3.44
87.5
,
2.19
55.7
,
,
8.37
212.5
,
,
,
9.97
253.2
,
34.57
878.1
,
ЕДИНИЦЫ ИЗМЕРЕНИЯ: [МИЛЛИМЕТРЫ]
ДЮЙМЫ
1.00
25.4
,
,
LTA
,
,.32 8.1
,
.53
13.5
,
,
,
,
,
,
,
,
,
,
,
,
,
,
5.91
,
5.41
137.5
,
,
4.92
125
,
, 112.5
4.43
,
3.94
100
,
,
3.44
87.5
,
2.95
75
,
,
2.46
62.5
,
1.97
50
,
,
1.48
37.5
,
.98
25
,.49 12.5
,
,
2.00
50.8
,
,
,
5.29
134.5
,
.57
14.4
,
MINIMUM UPRIGHT
МИНИМАЛЬНЫЙ
ЗАЗОР МЕЖДУ [304,8]
SPACING IS 12"
НАСТЕННЫМИ КРОНШТЕЙНАМИ
12
12°
,
,
1.00
25.4
,
,.34 8.6
,
21.00
533.4
,
,
1.44
36.6
,
,
12.00
304.8
,
,
,
7.00
177.8
20.54
521.7
,
,
0
,
,
13.23
336
,
,
,
,
,
,
2.18
55.3
,
,
,.93 23.6
,
,
,
,
ЕДИНИЦЫ ИЗМЕРЕНИЯ: [МИЛЛИМЕТРЫ]
ДЮЙМЫ
15
Серия LSA/LTA
16
Серия LSA/LTA
ИНСТРУМЕНТЫ, НЕОБХОДИМЫЕ ДЛЯ УСТАНОВКИ
A (8)
M4x16 мм
D (6)
M5x16 мм
B (6)
M4x20 мм
C (6)
M4x25 мм
E (6)
M5x20 мм
F (6)
M5x25 мм
R (1)
G (6)
M6x16 мм
H (6)
M6x25 мм
LSA2XXX/
LTA2XXX
I (6)
M8x20 мм
L (8)
,750x,323x,250
J (6)
M8x30 мм
M (8)
,750x,344x,500
K (4)
M8x50 мм
N (8)
P (1)
M5
S (1)
(Только для LTA)
T (1)
(Только для LSA)
U (1)
W (1)
QA (4)
5/16"
QB (4)
5/16"
V (1)
QC (4)
5/16" x 2-1/2"
(Только для LSA)
17
X (1)
(Только для LTA)
Серия LSA/LTA
УСТАНОВКА
5.
2.
6.
7.
4.
5
6
7
10
(QC) x 4
8
6"
9
(QB) x 4
рис. 2
8.
Середина кронштейна
по вертикали
рис. 1
18
Серия LSA/LTA
2.
3.
4.
6 10
(QA) x 4
4
8
5
9
x4
7 11
(QB) x 4
(QC) x 4
рис. 3
5.
6.
7.
8.
9.
19
Серия LSA/LTA
1
рис. 4
2.
20
2
рис. 5
3.
Серия LSA/LTA
Средняя линия (CL)
3d
рис. 7
2.
4.
21
Серия LSA/LTA
2
Верх
Скоба
5
2.
(S)
2
1
рис. 9
22
Серия LSA/LTA
23
Серия LSA/LTA
Chief Manufacturing, производственное
подразделение компании Milestone
AV Technologies.
8831-000023 Ред.03
®2011 Milestone AV Technologies
совместная компания Duchossois
www.chiefmfg.com
02/11
США/Международное представительство
Адрес: 8401 Eagle Creek Parkway, Savage, MN 55378
тел.: 800.582.6480 / 952.894.6280
факс: 877.894.6918 / 952.894.6918
Европа
Адрес: Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
тел.: +31 (0)40 2668620
факс: +31 (0)40 2668615
Азия и Тихоокеанский регион
Адрес: Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street Fotan, Shatin, Hong Kong
тел.: 852 2145 4099
факс: 852 2145 4477