Omron HEM-780, COMFIT HEM-780 User manual

HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 1
INSTRUCTION MANUAL
Automatic Blood Pressure Monitor
with ComFit™ Cuff
Model HEM-780
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 2
TABLE OF CONTENTS
Before Using the Monitor
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Risk of Electrical Shock . . . . . . . . . . . . . . . . . . . . . . . . .6
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Before Taking a Measurement . . . . . . . . . . . . . . . . . . . . . . . . .8
Operating Instructions
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unit Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Irregular Heartbeat Symbol . . . . . . . . . . . . . . . . . . . . . . 11
Movement Error Symbol . . . . . . . . . . . . . . . . . . . . . . . . 11
USER ID Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Morning Hypertension Symbol . . . . . . . . . . . . . . . . . . . 12
Heartbeat Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Average Value Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Morning Average Symbol . . . . . . . . . . . . . . . . . . . . . . . 13
Evening Average Symbol . . . . . . . . . . . . . . . . . . . . . . . . 13
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the AC Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Applying the Arm Cuff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 3
TABLE OF CONTENTS
Taking a Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Using the Guest Mode . . . . . . . . . . . . . . . . . . . . . . . . . 26
Selecting the USER ID . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using the USER ID . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting the TruRead™ Mode . . . . . . . . . . . . . . . . . . . 28
Using the Single Mode . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using the TruRead™ Mode . . . . . . . . . . . . . . . . . . . . . . 33
Special Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the Memory Function . . . . . . . . . . . . . . . . . . . . . . . . . 36
Averaging Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
To Display the Measurement Values . . . . . . . . . . . . . . 37
Morning and Evening Averages . . . . . . . . . . . . . . . . . . 39
Morning Averages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Evening Averages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
To Display Morning and Evening Averages . . . . . . . . . 40
Display Combinations . . . . . . . . . . . . . . . . . . . . . . . . . 41
To Delete All Values Stored in the Memory . . . . . . . . 42
Care and Maintenance
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Error Indicators and Troubleshooting Tips . . . . . . . . . . . . . 45
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 4
INTRODUCTION
Thank you for purchasing the Omron® HEM-780 IntelliSense®
Automatic Blood Pressure Monitor with ComFit™ Cuff.
Fill in for future reference.
DATE PURCHASED: __________________
SERIAL NUMBER: ____________________
Staple your purchase receipt here
Your new digital blood pressure monitor uses the oscillometric
method of blood pressure measurement. This means the monitor
detects your blood’s movement through your brachial artery and
converts the movements into a digital reading. The monitor stores
measurement results for two people and features Morning and
Evening Averages. TruReadTM allows for three consecutive
measurements with timed intervals for an average reading.
The HEM-780 comes with the following components:
• Monitor
• ComFitTM Cuff • AC Adapter
• 4 “AA” Batteries • Storage Case
• Instruction Manual printed in English and Spanish
• Warranty Card
The HEM-780 IntelliSense® Automatic Blood Pressure Monitor is
intended for home use.
SAVE THESE INSTRUCTIONS
4
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 5
SAFETY INFORMATION
To assure the correct use of the product basic safety measures should
always be followed including the warnings and cautions listed in this
instruction manual.
SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL
WARNING
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury to the user or patient or
damage to the equipment or other property.
OPERATING THE DEVICE
Contact your physician for specific information about your blood
pressure. Self-diagnosis and treatment using measured results may
be dangerous. Follow the instructions of your physician or
licensed healthcare provider.
If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Contact a physician immediately.
Read all of the information in the instruction manual and any
other literature in the box before operating the unit.
This device is intended for use in measuring blood pressure and
pulse rate in the adult population. Do not use this device on
infants or persons who cannot express their intentions.
5
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 6
SAFETY INFORMATION
Read the Special Conditions section (page 35) of the instruction
manual if your systolic pressure is known to be more than 220
mmHg. Inflating to a higher pressure than necessary may result
in bruising where the cuff is applied.
Operate the device only as intended. Do not use the device for
any other purpose.
Dispose of the device, components and optional accessories
according to applicable local regulations. Unlawful disposal may
cause environmental pollution.
Do not use a cellular phone near the device. It may result in an
operational failure.
Use only Omron authorized parts and accessories. Parts and
accessories not approved for use with the device may damage the
unit.
RISK OF ELECTRICAL SHOCK
Do not plug or unplug the power cord into the electrical outlet
with wet hands.
Do not overload power outlets. Plug the device into the
appropriate voltage outlet.
6
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 7
SAFETY INFORMATION
CARE AND MAINTENANCE
Do not subject the monitor to strong shocks, such as dropping
the unit on the floor.
Do not submerge the device or any of the components in water.
Store the device and the components in a clean, safe location.
Changes or modification not approved by Omron Healthcare will
void the user warranty.
7
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 8
BEFORE TAKING A MEASUREMENT
To ensure a reliable reading follow these recommendations:
1. Avoid eating, smoking, exercising, and bathing for 30 minutes
before taking a measurement. Rest for at least 15 minutes before
taking the measurement.
2. Stress raises blood pressure. Avoid taking measurements during
stressful times.
3. Measurements should be taken in a quiet place.
4. Remove tight-fitting clothing from your arm.
5. Sit in a chair with your feet flat on the floor. Rest your arm on a
table so that the cuff is at the same level as your heart.
6. Remain still and do not talk during the measurement.
7. Keep a record of your blood pressure and pulse readings for your
physician. A single measurement does not provide an accurate
indication of your true blood pressure. You need to take and record
several readings over a period of time. Try to measure your
blood pressure at about the same time each day for consistency.
8
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 9
KNOW YOUR UNIT
Main Unit:
Display
USER ID Selection
Switch
Battery Compartment
Start/Stop
Button
Memory (
) Button
Air Jack
Morning/Evening Average
(
/
) Buttons
AC Adapter Jack
SET Button
Components:
Air Tube
Four “AA” Batteries
Air Plug
(Connects to Air Jack)
Storage Case
Housing
Arm Cuff
Cord
AC Adapter
9
Instruction Manual
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 10
UNIT DISPLAY
Systolic Blood Pressure
USER ID Symbol (A or B)
Diastolic Blood Pressure
Morning Hypertension Symbol
Heartbeat Symbol
Movement Symbol
Irregular Heartbeat Symbol
Deflation Symbol
Morning Average Symbol
Evening Average Symbol
Average Value Symbol
Date/Time Display
Memory Symbol
Low Battery Indicator
Pulse Display
Week Display
TruRead™ Symbol
10
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 11
DISPLAY SYMBOLS
IRREGULAR HEARTBEAT SYMBOL ( )
When the monitor detects an irregular rhythm two or more times
during the measurement, the Irregular Heartbeat Symbol (
) will
appear on the display with the measurement values.
An irregular heartbeat rhythm is defined
as a rhythm that varies by less than 25%
from the average rhythm or 25% more
than the average rhythm detected while
the monitor is measuring the systolic
and diastolic blood pressure.
If the irregular heartbeat symbol ( )
displays with your measurement results,
we recommend you consult your
physician. Follow the directions of
your doctor.
Normal Heartbeat
Pulse
Blood
pressure
Irregular Heartbeat
Short Long
Pulse
Blood
pressure
MOVEMENT ERROR SYMBOL (
)
The Movement Error Symbol is displayed if you move your body
during the measurement. Please remove the arm cuff, and wait 2-3
minutes. Take another measurement.
USER ID SYMBOL ( / )
The USER ID Symbol indicates USER A or USER B as selected by
the user to take a measurement or when using the memory function.
The USER ID Symbol is not displayed when using the Guest Mode to
take a measurement.
11
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 12
DISPLAY SYMBOLS
The American Heart Association1 recommends the following guideline
for upper limit of normal for home blood pressure readings:
AHA Home Guideline for Upper Limit of Normal BP
Systolic Blood Pressure
135 mmHg
Diastolic Blood Pressure
85 mmHg
This is a general guideline because blood pressure depends
on age and morbidity. The AHA recommends a lower home
blood pressure goal for certain patients, including diabetic
patients, pregnant women, and patients with renal failure1.
The monitor is not intended to be a diagnostic device.
WARNING
Contact your physician for specific information about your
blood pressure. Self-diagnosis and treatment using measured
results may be dangerous. Follow the instructions of your
physician or licensed healthcare provider.
Omron Healthcare recommends you contact your physician if the
MORNING HYPERTENSION SYMBOL and/or the HEARTBEAT
SYMBOL appear on the display with your measurement values.
MORNING HYPERTENSION SYMBOL (
)
The Morning Hypertension Symbol is displayed if the morning
average reading for a week is above 135 for the Systolic Blood Pressure
value and/or 85 for the Diastolic Blood Pressure value when viewing
the Morning Averages and the Evening Averages in the memory.
1
American Heart Association Scientific Statement 2004
12
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 13
DISPLAY SYMBOLS
HEARTBEAT SYMBOL (
)
TAKING A MEASUREMENT
The Heartbeat Symbol flashes on the display during the
measurement. The Heartbeat Symbol flashes at every heartbeat.
When the measurement is complete, the Heartbeat Symbol
flashes on the display with your blood pressure and pulse rate if
the reading is above 135 for the Systolic Blood Pressure value
and/or 85 for the Diastolic Blood Pressure value.
USING THE MEMORY FUNCTION
The Heartbeat Symbol flashes when the blood pressure reading
stored in the memory is above 135 for the Systolic Blood
Pressure value and/or 85 for the Diastolic Blood Pressure value.
AVERAGE VALUE SYMBOL (
)
The Average Value Symbol is displayed when you press the memory
button. The most recent average reading appears on the display screen.
MORNING AVERAGE SYMBOL (
)
The Morning Average symbol is displayed when viewing Morning
Averages using the Memory Function.
EVENING AVERAGE SYMBOL (
)
The Evening Average symbol is displayed when viewing Evening
Averages using the Memory Function.
13
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 14
BATTERY INSTALLATION
Battery Cover
1. Press the t indicator on the battery
cover and slide the cover off in the
direction of the arrow.
2. Install 4 “AA” size batteries so the
+ (positive) and - (negative) polarities
match the polarities of the battery
compartment as indicated.
3. Replace the battery cover.
14
|
{
|
{
{
|
{
|
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 15
BATTERY INSTALLATION
BATTERY REPLACEMENT
Low Battery Indicator
When the Low Battery Indicator appears on the display screen turn
the monitor off and remove all the batteries. Replace with four new
batteries at the same time. Longlife alkaline batteries are recommended.
CAUTION
If battery fluid should get in your eyes, immediately rinse
with plenty of clean water. Contact a physician immediately.
NOTES: • Turn the unit off before replacing the batteries. If
the batteries are removed while the unit is still on,
the date and time will be reset to that of the previous
use. However, the measurement results are not deleted.
• When the batteries are replaced, you may need to
reset the date and time. If the year is flashing on the
display screen, refer to page 21, RESETTING THE
DATE AND TIME.
• The supplied batteries may have a shorter life.
CAUTION
Dispose of the device, components and optional accessories
according to applicable local regulations. Unlawful disposal may
cause environmental pollution.
15
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 16
USING THE AC ADAPTER
Use only the authorized Omron AC Adapter, Model Number HEMADPT1,with this monitor.
We recommend you install the batteries even if the AC Adapter is
used. If no batteries are installed, you may need to reset the date and
time if the AC Adapter is disconnected. The measurement results
will not be deleted.
CAUTION
Use only Omron authorized parts and accessories. Parts and
accessories not approved for use with the device may damage
the unit.
16
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 17
USING THE AC ADAPTER
TO CONNECT THE AC ADAPTER
1 Insert the AC Adapter Plug into
the AC Adapter Jack on the back
side of the monitor as illustrated.
2
Housing
2
1
Plug the AC Adapter into a 120V
AC outlet (60 cycles).
Cord
TO DISCONNECT THE AC ADAPTER
1 Hold the Housing to remove the AC Adapter from the
electrical outlet.
2
Remove the AC Adapter plug from the monitor.
WARNING
Do not plug or unplug the power cord into the electrical outlet
with wet hands.
CAUTION
Do not overload power outlets. Plug the device into the appropriate
voltage outlet.
17
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 18
SETTING THE DATE AND TIME
Set the monitor to the current date and time before taking a
measurement for the first time. If the date and time are not set
correctly, the measurement values stored in the memory and the
average values may not be correct.
The Blood Pressure Monitor automatically stores up to 84 individual
measurements values with the dates and times. The monitor also
calculates weekly averages for measurements in the morning and in
the evening. Morning and evening averages are stored for this week
and the last seven weeks.
The monitor can also calculate an average reading based on the three
most recent measurements taken within 10 minutes of the last reading.
NOTES: • If only two readings are stored in the memory for the
10-minute period, the average is based on the two readings.
• If one reading is stored in the memory for the 10-minute
period, this reading is displayed as the average.
1. TO START THE SETTING
Press and hold the SET button
to adjust the date and time.
The year flashes on the display.
18
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 19
SETTING THE DATE AND TIME
2. SETTING THE YEAR
The year can be set between
2006 and 2030. When the
display reaches 2030, it will
return to 2006.
Press the Memory button ( )
to advance by increments of
one year.
Press the SET button to set the
current year.
The month flashes on the display.
NOTE: Press and hold the Memory button ( )
to advance the date and time values faster.
3. SETTING THE MONTH
Press the Memory button (
one month.
) to advance by increments of
Press the SET button to set the
current month.
The day flashes on the display.
19
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 20
SETTING THE DATE AND TIME
4. SETTING THE DAY
Press the Memory button ( ) to advance by increments of one day.
Press the SET button to set the current day.
The hour flashes on the display.
5. SETTING THE HOUR
The time is set using AM or PM.
Press the Memory button ( ) to
advance by increments of one hour.
Press the SET button to set the current hour.
The minute flashes on the display.
6. SETTING THE MINUTE
Press the Memory button ( ) to
advance by increments of one minute.
Press the SET button to set the minute setting.
7. TO TURN THE MONITOR OFF
Press the START/STOP button.
NOTE: The monitor will automatically turn off after the minute
has been set after battery replacement.
20
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 21
SETTING THE DATE AND TIME
RESETTING THE DATE AND TIME
To adjust the date or time after it has been setup when you first use
the unit:
Start with the monitor in the off position.
1. Press and hold the SET button.
and the current setting (on or oFF)
The TruReadTM symbol
will appear on the display for the USER ID selected.
To change the on or oFF setting press the Memory button, then
press the SET button.
The interval time flashes on the display. Press the Memory button
to select the desired interval time, then press the SET button.
The year flashes on the display.
2. Refer to page 18, Setting the Date and Time.
NOTE: If you need to change the Date and Time,
always adjust the Date and Time setting before taking
the next measurement.
21
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 22
APPLYING THE ARM CUFF
CAUTION
Read all of the information in the instruction manual and any
other literature in the box before operating the unit.
CAUTION
This device is intended for use in measuring blood pressure and
pulse rate in the adult population. Do not use this device on
infants or persons who cannot express their intentions.
APPLYING THE CUFF ON THE LEFT ARM
1. Make sure the air plug is securely inserted in the main unit.
2. Remove tight-fitting clothing from your upper left arm.
22
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 23
APPLYING THE ARM CUFF
3. Sit in a chair with your feet flat on the floor. Place your left arm
on a table so the cuff is level with your heart.
4. Hold the grip on the cuff securely
with your right hand, placing your
thumb on the thumb grip.
Thumb Grip
Cloth Strip
5. Turn the palm of your left
hand upward.
23
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 24
APPLYING THE ARM CUFF
6. Apply the cuff to your left upper arm so the blue strip is on the
inside of your arm and aligned with your middle finger. The air
tube runs down the inside of your arm. The bottom of the cuff
should be approximately 1/2" above your elbow.
Blue Strip
1/2 inch (1 - 2 cm)
Air Tube
7. Wrap the cuff firmly in place around your arm using the cloth strip.
24
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 25
APPLYING THE ARM CUFF
APPLYING THE CUFF ON THE RIGHT ARM
When taking a measurement using the right arm use this instruction
for Step 6 on page 24.
Apply the cuff to your right upper arm so the thumb grip is centered
on the inside of your inner arm. The bottom of the cuff should be
approximately 1/2'' above your elbow.
Thumb Grip
NOTE: Be careful not to rest your arm on the air tube. This will
restrict the flow of air to the cuff.
25
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 26
TAKING A MEASUREMENT
The monitor is designed to take measurements and store the
measurement values in the memory for two people using
USER ID A and USER ID B.
The monitor can also be used to take a single measurement for other
persons using the GUEST Mode. The USER ID symbol is not
displayed when using the GUEST Mode. Measurements taken using
the GUEST Mode are not stored in the memory.
CAUTION
Operate the device only as intended. Do not use the device for
any other purpose.
USING THE GUEST MODE
1. Press and hold the START/STOP button.
The A and B Symbols disappear from the display.
A and B Symbols disappear
2. Release the START/STOP button.
The cuff starts to inflate automatically.
NOTE: To stop the inflation press the START/STOP button.
The monitor will stop inflating, start deflation and turn off.
26
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 27
TAKING A MEASUREMENT
3. Inflation stops and the measurement is started. When the
measurement is completed, your blood pressure and pulse rate
appear on the display.
SELECTING THE USER ID
Select your USER ID. Always use the same USER ID when taking a
measurement. The monitor stores the measurement values in the
memory by the USER ID selected. These measurement values are
used to calculate the Morning Averages and Evening Averages.
Slide the USER ID Selection Switch up or down to select USER A or B.
USING THE USER ID
When you select a USER ID the monitor can be set to take one
measurement using the Single Mode or three consecutive
measurements using the TruReadTM Mode when you press the
START/STOP button.
NOTE: The default value is set to the Single Mode to take
one measurement.
The TruReadTM Mode takes three consecutive measurements. The
monitor will inflate, take a measurement, and deflate three times
separated by a short interval of time between each measurement.
27
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 28
TAKING A MEASUREMENT
SELECTING THE TruReadTM MODE
1. Select your USER ID (A or B).
2. Press and hold the SET button.
and the oFF setting appears on
The TruRead™ symbol
the display.
3. Press the Memory button (
to select on.
)
NOTE: Press the Memory button to
alternate between on and oFF.
28
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 29
TAKING A MEASUREMENT
4. Press the SET button to confirm the change.
The number of seconds between each measurement is displayed.
NOTE: The default value between each measurement is 60 seconds.
5. Press the MEMORY button (
between each measurement.
) to change the interval of time
The interval can be set to 15 seconds, 30 seconds, 60 seconds or
120 seconds. Continue to press the MEMORY button until the
desired interval appears on the display.
6. Press the SET button to confirm
the setting.
The year flashes on the display.
29
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 30
TAKING A MEASUREMENT
7. If the date and time are correct, press
the START/STOP button to turn the
monitor off.
To change the date and time refer to
page 18, SETTING THE DATE
AND TIME.
CAUTION
Do not use a cellular phone near the device. It may result in an
operational failure.
USING THE SINGLE MODE
1. Select your USER ID (A or B).
30
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 31
TAKING A MEASUREMENT
2. Press the START/STOP button.
All symbols appear on the display. The USER ID Symbol you
selected flashes on the display.
The cuff starts to inflate automatically. As the cuff inflates, the
monitor automatically determines your ideal inflation level. This
monitor detects the pulse during inflation. Do not move your arm
and remain still until the entire measurement process is completed.
NOTE: To stop the inflation or measurement, press the
START/STOP button. The monitor will stop
inflating, start deflating and will turn off.
3. Inflation stops automatically and the measurement is started.
As the cuff deflates, decreasing numbers appear on the display.
The Heartbeat Symbol ( ) flashes at every heartbeat.
31
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
TAKING A MEASUREMENT
4. When the measurement is complete, the arm cuff
completely deflates. Your blood pressure and pulse
rate are displayed.
5. Press the START/STOP button to turn
the monitor off.
NOTE: The monitor will automatically
turn off after five minutes.
32
Page 32
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 33
TAKING A MEASUREMENT
USING THE TruRead™ MODE
1. Select your USER ID (A or B).
2. Press the START/STOP button.
All symbols appear on the display. The USER ID Symbol
you selected flashes on the display.
The cuff starts to inflate automatically.
NOTE: To stop the inflation or measurement, press the
START/STOP button. The monitor will stop
inflating, start deflating and will turn off.
3. Inflation stops automatically and the measurement is started.
As the cuff deflates, decreasing numbers appear on the display.
The Heartbeat Symbol ( ) flashes at every heartbeat. When
the measurement is complete, the arm cuff completely deflates.
NOTE: Do not move your arm and remain still until the entire
measurement process is completed.
4. Check the progress of the consecutive measurements.
NOTE: If a measurement fails, the monitor will repeat taking
a measurement up to five times during the consecutive
measurement process.
The first measurement is complete, waiting to start the next
measurement. The interval of time set between each
measurement will appear on the display.
33
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 34
TAKING A MEASUREMENT
The second measurement is complete, waiting to start the
next measurement.
The consecutive measurements are complete. The average for three
measurements appears on the display.
5. Press the SET button to display the blood pressure and pulse rate
for the first measurement. Press the SET button again to display
the next measurement.
6. Press the START/STOP button to turn the monitor off.
34
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 35
TAKING A MEASUREMENT
SPECIAL CONDITIONS
CAUTION
Inflating to a higher pressure than necessary may result in
bruising where the cuff is applied.
If your systolic pressure is known to be more than 220 mmHg, press
and hold the START/STOP button until the monitor inflates 30 to
40 mmHg higher than your expected systolic pressure.
NOTE: • Do not apply more pressure than necessary.
• The monitor will not inflate above 299 mmHg.
When the measurement is complete, the arm cuff completely
deflates. Your blood pressure and pulse rate are displayed.
35
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 36
USING THE MEMORY FUNCTION
The monitor is designed to store the blood pressure and the pulse
rate in the memory for two people (USER A and USER B) every
time a measurement is completed.
The monitor automatically stores up to 84 sets of measurement
values (blood pressure and pulse rate) for each user (A and B). When
84 sets of measurement values are stored, the oldest record is deleted
to save the most recent values. The monitor also stores 8 weeks of
Morning Averages and 8 weeks of Evening Averages for each user
(A and B).
AVERAGING FUNCTION
The monitor calculates the average reading based on the three
most recent sets of measurement values taken within 10 minutes
of the most recent reading.
NOTE: If two sets of measurement values are stored in the memory
for the 10 minutes period, the average is based on the two sets
of measurement values. If one set of measurement values is
stored, this is displayed as the average.
36
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 37
USING THE MEMORY FUNCTION
TO DISPLAY THE MEASUREMENT VALUES
1. Select your USER ID (A or B).
2. Press the Memory button (
The Average Symbol (
reading is shown.
).
) appears on the display when the average
37
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 38
USING THE MEMORY FUNCTION
3. Press the Memory button ( ) to display the most recent set of
measurement values on the screen. The values are displayed from
the most recent to the oldest.
NOTE: The date and time are alternately
displayed with the measurement values.
Alternating display
Press the Memory button to display the
next set of values.
Press and hold the Memory button to display the values faster.
TruRead™ MODE
The average for the consecutive measurements appears on the
). To display the values
display with the TruReadTM symbol (
for the individual measurements press the SET button while the
average is displayed.
4. Press the START/STOP button to turn the power off.
38
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 39
USING THE MEMORY FUNCTION
MORNING AND EVENING AVERAGES
The monitor calculates and displays a weekly average for
measurements taken in the morning ( ) and evening ( ). The
monitor stores 8 weeks of Morning Averages and 8 weeks of Evening
Averages for each user (A and B).
NOTE: The week begins Sunday at 4:00 A.M.
MORNING AVERAGES
Morning averages are based on the first average reading using the
TruRead™ Mode or the first reading using the Single Mode.
Measurement times must be between:
4:00 A.M. AND 9:59 A.M.
EVENING AVERAGES
Evening averages are based on the last average reading using the
TruRead™ Mode or the last reading using the Single Mode.
Measurement times must be between:
7:00 P.M. AND 1:59 A.M.
39
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 40
USING THE MEMORY FUNCTION
TO DISPLAY MORNING AND EVENING AVERAGES
1. Select your USER ID (A or B).
2. Press the Morning Average button
(
) or the Evening
Average button (
).
The average for the current
week “THIS WEEK” appears
on the display.
3. Continue to press the Morning Average button (
) or the
Evening Average button (
) to display the previous weeks.
The monitor displays “-1 WEEK” for the previous week to “-7
WEEK” for the oldest set of averages.
NOTE: If no measurement is taken in a
given week, the display will appear
as illustrated.
4. Press the START/STOP button to turn the monitor off.
40
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 41
USING THE MEMORY FUNCTION
DISPLAY COMBINATIONS
In addition to the Morning Average and Evening Average Symbols,
the monitor may also display the Morning Hypertension Symbol if
the morning average for that week is above the AHA guidelines. (See
page 12 for details.) Depending on your measurement results, these
may be displayed in the following combinations.
Display
Morning
Average
Morning average from This Week
with Morning Average Symbol
Morning average from 7 weeks ago
with Morning Average Symbol +
blinking Heartbeat Symbol +
Morning Hypertension Symbol
Evening
Average
Evening average from This Week
with Evening Average Symbol
Average within AHA guidelines
41
Evening average from 7 weeks ago
with Evening Average Symbol +
blinking Heartbeat Symbol +
Morning Hypertension Symbol
Average above AHA guidelines
+ Morning Hypertension
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 42
USING THE MEMORY FUNCTION
The Morning Hypertension Symbol ( ) appears if the weekly
average for morning measurements is above 135/85.
In this case the Morning Hypertension Symbol ( ) is displayed
when the Evening Average is displayed, regardless of the values
for the Evening Average.
TO DELETE ALL VALUES STORED IN THE MEMORY
The values stored in the memory are deleted by USER ID.
You cannot partially delete values stored in the memory. All values
for the user you select will be deleted.
1. Select your USER ID (A or B).
2. While holding the Memory button ( ) and the START/STOP
button simultaneously for more than 2 seconds all values will
be deleted.
42
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 43
CARE AND MAINTENANCE
To keep your digital blood pressure monitor in the best condition and
protect the unit from damage, follow the directions listed below:
Keep the monitor in the storage case
when not in use. Make sure the AC
adapter is placed under the main unit
so that it does not damage the display.
Avoid kinking or sharply bending the
AC Adapter cord.
Do not forcefully bend the arm cuff or
air tube. Do not fold tightly.
Clean the monitor with a soft dry cloth. Do not use any abrasive
or volatile cleaners. Do not attempt to clean the cuff.
CAUTION
Do not submerge the device or any of the components in water.
Do not subject the monitor to extreme hot or cold temperatures,
humidity or direct sunlight.
CAUTION
Store the device and the components in a clean, safe location.
CAUTION
Do not subject the monitor to strong shocks, such as dropping
the unit on the floor.
Remove the batteries if the unit will not be used for three months
or longer.
Always replace all the batteries with new ones at the same time.
43
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 44
CARE AND MAINTENANCE
Use the unit consistent with the instruction provided in this manual.
Use only authorized parts and accessories.
CAUTION
Changes or modification not approved by Omron Healthcare
will void the user warranty.
44
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 45
ERROR INDICATORS AND TROUBLESHOOTING TIPS
ERROR INDICATORS
SYMBOL
CAUSE
CORRECTION
Cuff under-inflated.
Cuff not applied
correctly.
Single Mode
Remove the arm cuff. Read,
“Taking a Measurement”.
Take another measurement.
TruReadTM Mode
The monitor will repeat the
process up to
5 times.
Cuff over-inflated
Monitor could not
detect pulse wave.
Take another measurement
and remain still until the
measurement is complete.
Air plug is
not connected.
Replace the four batteries.
Refer to “Battery Installation.”
Batteries are worn
45
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 46
ERROR INDICATORS AND TROUBLESHOOTING TIPS
TROUBLESHOOTING TIPS
PROBLEM
No power.
No display appears on
the unit.
Measurement values appear
too high or too low.
CAUSES AND SOLUTIONS
Replace all four batteries with new
ones. Check the battery installation
for proper placement
of the battery polarities.
Blood pressure varies constantly.
Many factors including stress, time
of day, and how you wrap the cuff,
may affect your blood pressure.
Review the sections “Before
Taking a Measurement” and
“Taking a Measurement.”
46
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 47
FCC STATEMENT
Note:
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)
This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. The product generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If the product does cause harmful interference to radio or television reception,
which can be determined by turning the product on and off, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the interference-causing equipment
standard entitled “Digital Apparatus”, ICES-003 of the Canadian Department
of Communications.
Cet appareil numérique respecte les limites de bruits radioeléctriques applicables
aux appareils numériques de Clase B prescrites dans la norme sur le materiel
brouilleur: “Appareils Numériques”, ICES-003 édictée par le minister des
communications.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
47
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 48
WARRANTY
Your HEM-780 IntelliSense® Automatic Blood Pressure Monitor, excluding the arm
cuff, is warranted to be free from defects in materials and workmanship appearing
within 5 years from the date of purchase, when used in accordance with the
instructions provided with the monitor. The arm cuff is warranted to be free from
defects in materials and workmanship appearing within one year from the date of
purchase when the monitor is used in accordance with the instructions provided
with the monitor. The above warranties extend only to the original retail purchaser.
We will, at our option, repair or replace without charge any monitor or arm cuff
covered by the above warranties. Repair or replacement is our only responsibility
and your only remedy under the above warranties.
To obtain warranty service contact Omron Healthcare for the address of the repair
location. Shipping instructions and repair information is available by calling
1-800-634-4350 or visit our website at www.omronhealthcare.com.
Enclose the Proof of Purchase. Include $5.00 for the return shipping and handling.
Include a letter, with your name, address, phone number, and description of
the specific problem. Pack the product carefully to prevent damage in transit.
Because of possible loss in transit, we recommend insuring the product with return
receipt requested.
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE
APPLICABLE WRITTEN WARRANTY ABOVE. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not
apply to you.
OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER
INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR
DAMAGES. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
FOR CUSTOMER SERVICE
Visit our web site at:
www.omronhealthcare.com
Call toll free:
1-800-634-4350
48
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page 49
SPECIFICATIONS
Model:
Display:
Measurement Range:
Accuracy/Calibration:
HEM-780
LCD Digital Display
Pressure: 0 to 299 mmHg, Pulse: 40-180/min.
Pressure: ±3mmHg or 2% of reading
Pulse:
±5% of reading
Inflation:
Automatic by electric pump
Deflation:
Automatic pressure release valve
Rapid Air Release:
Automatic exhaust valve
Pressure Detection:
Capacitive pressure sensor
Measurement Method: Oscillometric method
Pulse Wave Detection: Capacitance type pressure sensor
Power Source:
120V 60Hz AC adapter or 4 “AA” batteries
Battery Life:
Approx. 1400 uses when used 6 times a day
with 4 new alkaline batteries
Operating Temperature 50ºF to 104ºF (10ºC to 40ºC) /30 to 85% RH
/Humidity:
Storage Temperature
-4ºF to 140ºF (-20ºC to 60ºC) /10 to 95% RH
/Humidity/Air Pressure: /700 - 1060 hPa
Main Unit Weight:
Approximately 14 7/8 oz. (420 g)
not including batteries
Main Unit Dimensions: Approx. 6 3/32" (l) X 5 5/32" (w) X 3 5/16" (h)
(155 mm X 131 mm X 84 mm)
Cuff Size:
Approximately 6" (w) (152 mm)
Cuff tube 23 5/8" (l) (600 mm)
Cuff Circumference:
Fits arm circumferences 9" to 17"
(220 mm to 420 mm)
Memory:
Up to 84 per user
Weekly Averages:
Up to 8 weeks
Contents:
Main Unit, ComFitTM Cuff, AC Adapter, Instruction
Manual, 4 “AA” batteries, Storage Case and Warranty Card
UPC Code:
0 73796 78000 5
NOTE: These specifications are subject to change without notice.
49
HEM-7080-updated Sept 22.qxd
9/22/06
NOTES
50
3:46 PM
Page 50
HEM-7080-updated Sept 22.qxd
9/22/06
NOTES
51
3:46 PM
Page 51
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Manufactured by OMRON HEALTHCARE
Made in China
Distributed by:
OMRON HEALTHCARE, INC.
1200 Lakeside Drive
Bannockburn, Illinois 60015
www.omronhealthcare.com
Copyright © 2006 Omron Healthcare, Inc.
HEM-780N3INST Rev
Page 52
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page E1
MANUAL DE INSTRUCCIONES
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page E2
E2
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page E3
E3
HEM-7080-updated Sept 22.qxd
9/22/06
3:46 PM
Page E4
GUARDE ESTAS INSTRUCCIONES
E4
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E5
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E6
E6
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E7
E7
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E8
E8
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E9
Pantalla
Botón (
) de memoria
Botones (
matutino/nocturno
) de promedio
Componentes:
Tubo de aire
Estuche
Bastidor
E9
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E10
PANTALLA DE LA UNIDAD
Símbolo de ID DE
USUARIO (A o B)
Símbolo de
promedio matutino
Símbolo de
promedio nocturno
Símbolo de valor promedio
Símbolo de memoria
E10
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E11
sanguínea
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E12
135 mmHg
85 mmHg
E12
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E13
SÍMBOLOS DE LA PANTALLA
SÍMBOLO DE CORAZÓN (
)
CÓMO TOMAR UNA MEDICIÓN
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E14
|
{
|
{
E14
{
|
{
|
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E15
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E16
E16
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E17
2
Cable
2
E17
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E18
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E19
E19
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E20
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E21
E21
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E22
E22
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E23
Correa de tela
E23
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E24
Correa azul
1/2 pulgada (1 - 2 cm)
Tubo de aire
E24
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E25
E25
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E26
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E27
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E28
CÓMO TOMAR UNA MEDICIÓN
SELECCIÓN DEL MODO TruReadTM
1. Seleccione la ID DE USUARIO (A o B).
E28
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E29
E29
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E30
E30
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E31
E31
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E32
E32
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E33
E33
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E34
E34
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E35
CÓMO TOMAR UNA MEDICIÓN
CONDICIONES ESPECIALES
E35
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E36
E36
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E37
).
E37
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E38
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E39
E39
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E40
E40
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E41
Promedio
matutino
E41
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E42
E42
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E43
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E44
E44
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E45
INDICADORES DE ERROR Y SOLUCIÓN DE PROBLEMAS
INDICADORES DE ERROR
SÍMBOLO
CAUSA
CORRECCIÓN
E45
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E46
INDICADORES DE ERROR Y SOLUCIÓN DE PROBLEMAS
SUGERENCIAS PARA LA SOLUCIÓN DE PROBLEMAS
PROBLEMA
CAUSAS Y SOLUCIONES
E46
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E47
E47
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E48
www.omronhealthcare.com
E48
1-800-634-4350
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E49
HEM-780
E49
HEM-7080-updated Sept 22.qxd
9/22/06
NOTAS
E50
3:47 PM
Page E50
HEM-7080-updated Sept 22.qxd
9/22/06
NOTAS
E51
3:47 PM
Page E51
HEM-7080-updated Sept 22.qxd
9/22/06
3:47 PM
Page E52
Fabricado por OMRON HEALTHCARE
Hecho en China
Distribuido por:
OMRON HEALTHCARE, INC.
1200 Lakeside Drive
Bannockburn, Illinois 60015
www.omronhealthcare.com
Copyright © 2006 Omron Healthcare, Inc.
HEM-780N3INST Rev
1658806-1A