Laserworld EL-230RGB Manual

Manual / Bedienungsanleitung
/ Mode d´emploi
Evolution Series
ES-400RGB QS
Please spend a few minutes to read this manual fully
before operating this laser!
Bitte lesen Sie diese Bedienungsanleitung sorgfältig
vor Inbetriebnahme dieses Showlasersystems!
Avant d’utiliser cet appareil pour la première fois nous vous recommandons
de lire cette notice d’utilisation!
Legal notice:
Content:
Thank you for purchasing this Laserworld
product. Due to continual product developments and technical improvements, Laserworld (Switzerland) AG reserves the right to make modifications to its products.
This manual and its content have been made with due care but Laserworld (Switzerland) AG cannot however, take any responsibility for any errors, omissions or any
resulting damages forthwith. The brands and product names mentioned in this manual are trade marks or registered trade marks of their respective owners.
1.
Product and package contents
2.
Preliminary warning notices
3.
Initial operations, safety instructions
4.
Working on the device
5.
Service notes
6.
Warnings and other notices on the device
7.
8. Operation
Final statement
Technical data sheet
Laser specifications
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x manual
2 x key
1 x power cable
1 x Interlock Connector
2. Preliminary warning notices
dent prevention.
10. If the device has been exposed to
great temperature changes, do
not switch it on immediately. Condensation (or any moisture/water
formed) may damage device.
11. Never use dimmer, RC or other
electronically switched sockets.
Whenever possible, do not use the
laser projector together with large
appliances (especially fog machines) on the same mains!
do not place the device on any
warm or heat radiating surface. Especially the ventilation openings
must not be covered!
13. Ensure that device does not gets
overheated. Make sure that the
device is not exposed to spotlights
(especially moving heads). Heat of
spotlights could overheat laser in a
little while and leads to a degradation of performance.
1.
Please use this device only according to these operating instructions.
2.
Do not use the device if there are any visible damages on housing, connector
panels, power supplies or power cords.
3.
ever look directly into the light source of a laser projector. Danger of damaN
ge to the eyes or even blindness in extreme circumstances!
4.
Do not operate the device at high humidity, rain or in dusty surroundings.
4. Working on the device
5.
Protect device against dripping or splashing water. Do not place any liquid
filled containers near to this device.
1.
This product has no user serviceable parts inside and
should only be maintained and serviced by a qualified engineer.
2.
Be sure that the mains plug is not connected
to the power supply while installing or opening
the device (e.g. for cleaning).
3.
Take off all reflecting things like rings, watches etc. before
start working with or at the projector.
4.
Use only non-reflecting tools to work on device.
5.
Wear protective clothing (like goggles, gloves etc.) according to laser power
and wavelength of the laser.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.
3. Initial operations, safety instructions
1.
2.
3.
4.
5.
Make sure to use correct voltage;
see information on device & in this
manual.
6.
Make sure that the device is not
connected to mains during installation.
7.
The power supply should be easily
accessible.
8.
When installing the laser keep
mount it with a minimum distance
of 15 cm from walls and objects.
9.
For safe setup e.g. on walls or
ceilings please use a safety cord.
The safety cord should be able to
withstand tenfold the weight of
the device. Please follow the accident prevention regulations of
professional associations and/or
comparable regulations for acci-
Installation has to be done by
technical experienced and qualified persons according to safety regulations of the respective
country.
Always ensure that maximum
permissible exposure (MPE) is not
exceeded in areas accessible to the
public or members of staff.
In some countries an additional
inspection by technical control in-
stitutes could be necessary.
Connect an easily accessible interlock connector or circuit breaker
to the projector.
14. This unit is intended for indoor use
only.
5. Service notes
•
•
•
•
--
Moisture and heat can reduce lifetime of the laser system dramatically and
expires any warranty claim.
Quick on/off switching of this device will reduce durability of the laser diode
dramatically.
Avoid sharp knocks and shocks to this device and ensure sufficient protection
during transportation. Look after your Laserworld product.
To increase durability of your laser, protect device against overheating:
Always ensure sufficient ventilation.
---
--
-•
o not face spotlights (especially
D
moving heads) to the device.
Check temperature after approx.
30 minutes with each new installation. If necessary install the
projector at a place with different
temperature.
Switch off device when it is not
needed. Diodes are switched on
and can wear out even if there is
no visible laser output.
Keep the device dry. Protect it
from moisture, rain and damp.
The devices of Ecoline, Evolution,
Club and Proline Series are not
meant for professional applications. After approx. one hour of
•
•
operation, the device should cool
down for about 15 minutes.
Please ensure the fans and
heatsinks are clear from dust and
debris otherwise the risk of overheating may occur. If the unit and
airways appear to be blocked then
please contact a qualified service
engineer to maintain and service
the product.
Removal of the warranty label
as well as damages to the device
caused by improper handling,
neglect of the safety instructions and service notes will void
the warranty.
LEDs:
Sound sensitivity,
Laser emission
microphone
Laser aperture
warning label
trim pot for
music-sensitivity
key switch
DMX address,
operation mode
Interlock
ON/OFF switch
6. Warnings and other notices on the device
mains connection
DMX out DMX in Size of projection
Model type
to beam
Production year
Laser class 3b
Wavelength
Caution of radiation if cover
Output power
is removed
Use in enclosed spaces only!
Power supply
8. Operation
a.
b.
c.
d.
Connect the power cable to the device and then to the mains
Insert the key into the key switch and turn it „ON“
Connect the Interlock Connector with the Interlock interface
Press „ON“ to switch the device on
8.1. Automatic, Stand-alone operation
Set the device to auto mode:
8.2. Music mode, Sound-to-light operation
Your device runs in music mode:
Control the music-sensitivity with the trim pot at the front panel. The LED is flashing when the device is triggered.
8.3. DMX-512 mode
Channel
Value
Function
7
0 - 255
Zoom / size
8
0- 255
Color
9
above 200
Reset
10
0 - 255
Rotate x axis
11
0 - 255
Rotate y axis
12
0 - 255
Rotate z axis
Please note that a pattern can not necessarily be combined with each effect.
Switch 10 must be set to „off“, the other switches are used for setting the DMX
address:
8.4. Turn laser off
To turn off the device switch it off („OFF“), switch the key to „OFF“ and disconnect
the power cable from the mains.
Connect a DMX controller to operate the laser.
Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a
number. To define a number use the preceding number and multiply it by 2:
Switch
1
2
3
4
5
6
7
8
9
10
Number
1
2
4
8
16
32
64
128
256
Mode Switch
The laser uses 12 DMX channels, so make sure that the next device uses an address
that doesn’t overlap with this range.
Channel
Value
Function
1
0 - 69
Laser off
70 - 139
Sound mode
140 - 209
Automatic mode
210 - 255
DMX mode
2
0 - 255
Pattern selection
3
0 - 255
Strobe effect
4
-
-
5
0 - 255
x axis positioning
6
0 - 255
y axis positioning
Final statement
Laserworld products are tested and product packaging is inspected before leaving
our warehouse. Users must to follow the local safety regulations and warnings
within this manual and adhere to any regulations within its place of use. Damages
through inappropriate use will void any liability or warranty of our products. Due to
continual product developments, please check for the latest update of this product
manual at www.laserworld.com. If you do have any further questions, then please
contact your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only
genuine Laserworld spare parts are used in any service repairs.
Errors and omissions excepted and products are subject to change.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil
SWITZERLAND
Registered office:
8574 Lengwil / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE258030001
WEEE-Reg.-No. (Germany): DE 90759352
www.laserworld.com
[email protected]
representative according to EMVG:
Ray Technologies GmbH
Managing Director: Karl-Heinz Käs
Mühlbachweg 2
83626 Valley / Germany
1.
2.
3.
1.
4.
2.
5.
6. 3.
7.
8. 4.
5.
1.
2.
3.
4.
5.
6.
7.
8.
9.
•
•
•
--
--
--
--
1.
2.
3.
4.
5.
•
•
•
Laserstrah-
a.
Produktname
Produktionsjahr
Laserklasse 3b
b.
c.
d.
Mikrofon
Switch
1
2
3
4
5
6
7
8
9
10
Nummer
1
2
4
8
16
32
64
128
256
Modus
Wert
1
0 - 69
70 - 139
Musik Modus
140 - 209
Auto Modus
2
210 - 255
DMX Modus
0 - 255
3
0 - 255
Stroboeffekt
4
-
-
5
0 - 255
6
0 - 255
7
0 - 255
8
0- 255
Farbe
9
über 200
10
1 - 255
11
1 - 255
12
1 - 255
2.
3.
4.
5.
6.
7. 8.
Remarque finale
2.
3.
4.
5.
6.
7.
3.
4.
5.
6.
7.
8.
9.
•
•
•
2.
3.
4.
•
•
--
--
--
--
•
•
Interlock
LED:
Microphone,
Emission
Microphone
1
2
3
4
5
6
7
8
9
10
Nombre
1
2
4
8
16
32
64
128
256
Chgt de mode
Fonction
1
0 - 69
Laser off / blackout
70 - 139
Mode musical
140 - 209
2
210 - 255
0 - 255
3
0 - 255
Effet strobo
4
-
-
5
0 - 255
6
0 - 255
7
0 - 255
Zoom / taille
8
0 - 255
9
> 200
10
1 - 255
11
1 - 255
12
1 - 255
Remarque finale
DPSS (green), diode (red, blue)
DPSS (grün), Diode (rot, blau)
DPSS (vert), diode (rouge, bleu)
Laser class:
Laserklasse:
Classe laser
3b
Scanner:
high-speed stepper motors, 3-8kpps,
Highspeed Schrittmotoren, 3-8kpps
moteurs pas à pas haute performance, 3-8kpps
Scan angle:
Strahlauslenkung:
Angle de scan max.:
30° max.
Beam:
ca. 3mm / 2mrad
Power supply:
Stromversorgung:
Alimentation:
85V - 250V AC
Power consumption:
Stromaufnahme:
Consommation:
30W
+10° to +35°C
255 x 245 x 100 mm (L x W x H)/(B x T x H)/(H x L x P)
www.laserworld.com
[email protected]
3.9 kg
Power specifications (at laser module) / Laserleistung (am Modul) / Puissance
guar. - max.
Red / Rot / Rouge
(650nm)
320-400mW
110mW
50mW
160mW