Lasko LKO-7050-TN, LKO-7050, 7050 Operating manual

MODEL/MODELO 7050
IMPORTANT INSTRUCTIONS OPERATING MANUAL
NOTES/NOTAS
misto™
MODEL 7050
This Fan is for commercial and residential use only.
It is not intended to be used in industrial or agricultural settings.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL
SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE!
KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
SAVE THESE INSTRUCTIONS
Rev. C 9/12
12
7050ES
Rev. C 9/12
1
7050ES
MODELO 7050
MOLESTE PUNTAS que DISPARAN
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
1. This fan is an outdoor product and is NOT intended for indoor use. Do not leave the misto fan unattended when it is plugged in.
2. Make certain the power source conforms to the electrical requirements of the Fan. Completely assemble the fan before connecting
to power source. Do not use the fan with any solid state speed control.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons. Never place the fan where it may fall into a water reservoir such as a Pool or water container. Do not hang the
misto fan on a wall or ceiling or use in a window.
4. The misto fan should not be used as a toy. To reduce the risk of personal injury and electric shock, the Fan should not be played with or
placed where children can reach it.
5. Turn off the misto fan and unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE FAN.
ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN
UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or where gasoline,
paint or flammable liquids are used or stored.
7. CAUTION: Surfaces in the area of the fan may become slippery when wet.
The power cord is equipped with a three-prong, grounded GFCI (Ground Fault Circuit Interrupter) plug that must be inserted into a
grounded receptacle. Under no circumstances must the grounding prong be cut off the plug. WARNING: Do not use a three-prong
to two-prong adapter.Where a two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong
receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This work
must be done only by a qualified electrician, using copper wire only. The GFCI Fan cord set can be plugged into an existing GFCI
outlet if present.
RISK OF ELECTRIC SHOCK. TEST GFCI PLUG BEFORE EACH USE.
1. PLUG GFCI INTO POWER OUTLET. INDICATOR LIGHT SHOULD TURN ON.
2. PRESS TEST BUTTON. INDICATOR LIGHT SHOULD TURN OFF.
3. PRESS AND RELEASE RESET BUTTON. INDICATOR LIGHT SHOULD TURN ON.
If above test fails, DO NOT USE THIS GFCI FAN. Call 800-233-0268, Mon - Fri, 8:00 a.m. and 5:00 p.m. Eastern
USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT PERMITTED. IMPROPER CONNECTION MAY CREATE THE RISK OF
ELECTRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is
damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT remove, replace, repair or tamper with the originally
supplied plug or GFCI. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. Call
800-233-0268, Monday - Friday, between 8:00 a.m. and 5:00 p.m. Eastern. If the plug warning label is missing or damaged, call
the toll free number for a replacement label.
8. NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. This
GFCI plug does not protect against electrical shock due to contact with both circuit conductors or a fault in any wiring supplying this
device. Do not use an extension cord between the Fan GFCI cord and power outlet. Customer service is available at 800-233-0268,
Monday through Friday, 8am to 5pm to answer your questions.
9. DO NOT USE AN EXTENSION CORD WITH THIS FAN.
10. Prior to use, inspect for debris and/or insects.
11. NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,
or damage the Fan. To reduce the risk of fire, DO NOT block or tamper with the Fan in any manner while it is in operation.
12. Turn off water at the source before changing the nozzle.
13. Turn off water at the source after each use. Disconnect your garden hose from the valve adapter and drain unit to winterize.
14. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be
tripped over.
15. DO NOT use this Fan in close proximity to cooking grills, fire pits or other open flames.
16. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
17. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
18. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state
OR LOCAL CODES OR STANDARDS RELATING TO ELECTRICAL REQUIREMENTS FOR HAZARDOUS LOCATIONS. THIS FAN DOES
NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
MANTENIMIENTO
-
-
-
-
-
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS
FAN WITH ANY SOLID STATE SPEED CONTROL DEVICES.
Rev. C 9/12
SAVE THESE INSTRUCTIONS
2
Rev. C 9/12
11
7050ES
MODELO 7050
MODEL 7050
mistoTM
1. Observe Louvers during operation. Once
centered, place Louver power switch in Off (0)
position.
ASSEMBLY INSTRUCTIONS (Figure 1)
1.Carefully remove the Fan from the plastic bag and
the carton.
2.Place the Fan on a firm and level surface.
3.Plug the GFCI plug into a standard 120 volt AC outlet
with ground.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles,
they may slip partially or completely out of
the receptacle with only the slight movement of the attached cord. Receptacles in
this condition may overheat and pose a
serious fire hazard; if covered by a curtain
or drape, the fire hazard is even greater.
4. Attach the hose valve adapter to any garden hose or spigot.
Figure 1
If you use an Extension Cord, the
Extension Cord must be plugged into a
GFCI Protected Receptacle.
Figura 4
Filtro de la pantalla
Power Knob
Louver
Power Switch
OPERATING INSTRUCTIONS
1. Turn the Fan on by selecting the desired speed with the Power Knob on the side of the
Fan. 0-Off, 3-High, 2-Medium, 1-Low
(Figure 2)
2. Turn on water at the source. Turn the valve
adapter to the "Open" position. (Figure 3)
3. To adjust the vertical angle, push the Fan body forward or backward to the desired
position. It is normal to hear a clicking
sound while performing this function. IMPORTANT: Spray angle and droplet size is
determined by water pressure at your location.
Figure 2
Hose Valve
Adapter
LOUVER OSCILLATION:
Figura 5
Rev. C 9/12
10
7050ES
To operate internal air directing Louvers:
1. Turn the Power Knob to the desired speed
setting.
2. Push the Louver Power Switch to oscillate louvers.
Louvers will stop operating when:
1.Power to the unit is unplugged.
2. Power knob is in 0 -Off position.
3. Louver power switch is in Off position.
To center Louvers in Air Flow:
Rev. C 9/12
Figure 3
3
7050ES
MODEL 7050
mistoTM Outdoor Misting Fan:
MODELO 7050
INSTRUCCIONES DE ENSAMBLAJE
Misting Manifold Clean and Care Guide:
If the nozzles become clogged from contamination, follow the steps below:
1. Turn the water off at the source.
2. Remove the misting assembly’s valve adapter from garden hose or spigot and the hose adapter. Do this
carefully and allow residual water pressure to drain. Cycle (turn the handle back and forth) the valve and ensure freedom of movement and that there is no debris blocking the water’s path.
Hose Adapter
Rubber Gasket
Misting
Assembly
Valve Adapter
Figura 1
Screen Filter
3. Remove the screen filter from inside the Misting Assembly Valve Adapter. Inspect and ensure the screen
filter is free of buildup or debris. If filter is clogged, soak in a solution of undiluted 5% acidity distilled white
vinegar for at least 2 hours. For an immediate solution, replace the filter.
4. Carefully remove each misting nozzle from the nozzle housing by turning it counter-clockwise using your
hand or, if required, a pair of pliers. Soak the nozzles in a solution of undiluted 5% acidity distilled white
vinegar for at least 2 hours. For an immediate solution, replace the nozzles with the supplied replacement
parts. If more nozzles are required, call 1-800-233-0268, or order online at www.laskoproducts.com in Parts &
Accessories.
Misting Nozzles
Nozzle Housing
OSCILACIÓN DE LA REJILLA:
CERRADO
Figure 5
Figura 3
5. After the appropriate amount of soak time for the parts requiring cleaning, reassemble the misting
subsystem by inserting the misting nozzles into the Nozzle Housing and turning clockwise until secure.
(Figure 5) Only turn until hand tight; do not over tighten. Next, return the screen filter to the inside of the
manifold’s valve adapter. Finally, reattach the valve adapter to the hose adapter. (Figure 4)
6. You are now ready to continue to stay cool with your mistoTM Outdoor Misting Fan.
Rev. C 9/12
4
7050ES
Rev. C 9/12
9
7050ES
MODEL 7050
TROUBLE SHOOTING TIPS
If your Fan fails to operate, see below for a probable cause and solution:
1. Be sure the power cord is plugged into a working electrical outlet.
If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday
through Friday, between the hours of 8:00 a.m. and 5:00 p.m. Eastern.
MAINTENANCE
-
-
-
-
-
To reduce the risk of electrical shock and fire please observe the following instructions:
Always turn off the fan, unplug the cord and disconnect from the water supply before moving, servicing or cleaning.
Clean the Fan only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from inside the Fan.
NEVER attempt to take apart the Fan.
Clean the body of the Fan with a soft cloth only.
NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.
SERVICING:
For servicing, other than general user maintenance, please contact Customer Service at 800-233-0268, Monday
through Friday, from 8am-5pm Eastern.
STORAGE:
Store the Fan with these instructions, in the original carton in a cool, dry place.
 LASKO PRODUCTS, INC. LIMITED WARRANTY
(VALID IN THE USA, ITS TERRITORIES, AND CANADA ONLY)
WHAT THIS WARRANTY COVERS:  This product is warranted against defects in workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS:  This warranty extends only to the original purchaser of the product and lasts for one (1) year from the date of
original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
WHAT LASKO WILL DO: Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product
with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, Inc. at customer expense with proof
of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization (“RA”). DO NOT return
products without an RA or the warranty claim will not be processed.
WHAT THIS WARRANTY DOES NOT COVER:  This warranty does not apply if the product was damaged or failed because of accident, improper
handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted. This warranty does not cover shipping costs for
the return of products to Lasko for repair or replacement.  Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.
ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY),
LAST ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS
THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY
INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY
HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES.  NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL LASKO’S
LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY
SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.
Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so these exclusions or limitations may not apply to you.  This warranty gives you specific legal rights. You may also have other rights which
vary from state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.
CUSTOMER SERVICE:
Toll-Free (800) 233-0268. Email: [email protected]
Our Customer Service team is available to assist you with product and service questions, and replacement parts.
They can be reached Monday through Friday, 8am-5pm Eastern. Please have your model number available, as well
as the type and style (located on the underside of your product).
Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380
(Please do not send product to this location) www.laskoproducts.com
CONSERVE ESTAS INSTRUCCIONES
Rev. C 9/12
8
Manual printed in China
7050ES
Rev. C 9/12
5
7050ES
INSTRUCCIONES IMPORTANTES MANUAL DE OPERACIÓN
INFORMACIÓN GENERAL DE SEGURIDAD
LEA Y GUARDE ESTAS INSTRUCCIONES
LEA CUIDADOSAMENTE LAS INSTRUCCIONES ANTES DE
INTENTAR ARMAR, INSTALAR, USAR O DAR MANTENIMIENTO
AL PRODUCTO DESCRITO.
PROTÉJASE A SÍ MISMO Y A LOS DEMÁS CUMPLIENDO CON
TODA LA INFORMACIÓN DE SEGURIDAD. EL NO SEGUIR
LAS INSTRUCCIONES PODRÍA RESULTAR EN LESIONES
PERSONALES Y/O DAÑOS A LA PROPIEDAD.
CONSERVE LAS INSTRUCCIONES COMO FUTURA
REFERENCIA.
CONSERVE ESTAS INSTRUCCIONES
Rev. C 9/12
6
7050ES
7
7050ES