FULL ELECTRIC BARIATRIC BED
OWNER’S ASSEMBLY AND OPERATING MANUAL
CAMA BARIÁTRICA TOTALMENTE
ELÉCTRICA
INSTRUCCIONES DE MONTAJE Y MANUAL DE OPERACIÓN
LIT POUR PERSONNES OBÈSES
TOUT ÉLECTRIQUE
GUIDE D’ASSEMBLAGE ET D’UTILISATION
Item # 15300
REV3.4.10.14
(15300 Model Only)
Drive
Lifetime warranty on welds.
Five year warranty on frame.
One year warranty on all other parts and components.
During the warranty period, defective items will be repaired or replaced at
Drive’s option at no charge.
GENERAL WARNINGS
DO NOT use this product or any available optional
equipment without first completely reading and understanding these instructions and any additional instructional material such as owner’s manuals, service
manuals or instruction sheets supplied with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions, contact a
healthcare professional, dealer or technical personnel
before attempting to use this equipment - otherwise,
injury or damage may occur.
Read all the instructions before using the bed.
Refer to the owner’s manuals for beds and rails for additional product and safety information.
After any adjustments, repair or service and before
use, make sure all attaching hardware is tightened
securely.
After the bed has been assembled, always test to make
sure that all sections of the bed are properly and securely in place before using.
ALWAYS use caster locks except when moving the
bed.
Body weight should be evenly distributed over the
surface of the bed. DO NOT lay, sit or lean in such
a way that your entire body weight is placed only on
raised head or foot sections of the bed. This includes
when assisting the user in repositioning or transferring
in or out of bed.
DO NOT use this product or any available optional
equipment without first completely reading and understanding these instructions and any additional instructional material such as owner’s manuals, service
manuals or instruction sheets supplied with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions, contact a
healthcare professional, dealer or technical personnel
before attempting to use this equipment - otherwise,
injury or damage may occur.
For Dealers Only - Set-up and Assembly Instructions
are in the rear of this manual.These procedures must
be performed by a qualified technicians only.
The March 2006 version of the FDA’s bed safety
guidelines are published by Hospital Bed Safety
Workgroup. The latest revision of this document is
available at http://www.fda.gov.
If the unit is not working properly, call a qualified
technician to examine the unit and repair it.
Drive Medical products are specifically designed
and manufactured for use in conjunction with Drive
Medical accessories. Accessories designed by other
manufacturers have not been tested by Drive Medical
and are not recommended for use with Drive Medical
products.
Close supervision is necessary when this bed is used
by or near children or people with disabilities.
Keep all moving parts, including the main frame,
mattress deck (head and foot springs/sections) and all
drive shafts free of obstruction (i.e. blankets/sheets,
heating blankets/pads, tubing, wiring, etc. and other
types of products using electric cords which may get
tangled around the bed, side rails or legs) during operation of the bed.
DO NOT let any individual underneath the bed or in
between the raised bed frame components at anytime.
Keep the product a minimum of 12 inches away from
any direct heat source.
DO NOT permit more than one person on/in the bed at
any time.
Make sure head and foot springs/sections are connected securely to the universal bed ends before use.
Physically challenged individuals who cannot prevent
themselves from rolling/climbing out of the this bed
Check all parts for shipping damage and test before
using. In case of damage, DO NOT use. Contact a
qualified technician for further instruction.
DO NOT use outdoors.
may require alternative safe means of restraint.
Procedures other than those described in this manual
must be performed by a qualified technician.
Risk of injury to persons - DO NOT place video
equipment such as televisions or computer monitors
on bed.
NEVER allow patients to use trapeze or traction units
as a total individual weight support.
Trapeze units are to be used only for assisting the patient in repositioning or transferring into or out of bed.
Trapeze units must be positioned on a universal bed
end as near as possible to the center point of the bed
end.
The bed is not designed to be used as a patient transport. When transporting a patient, use an approved
patient transport. Otherwise, injury or damage may
result.
The bed may be equipped with locking casters. When
transferring into or out of the bed, always lock the
locking caster(s). Inspect for correct locking action
on caster locks before using bed. Even with casters
properly locked, some flooring surfaces such as tile or
wood, will allow the bed to move under some conditions. Use on surfaces such as these must be evaluated
by the care provider.
The initial set up of this bed must be performed by a
qualified technician.
The total weight limit of the Drive Medical 42-inch
(106.7 cm) wide Bariatric bed (including accessories,
mattress, occupant and any other person/object positioned on the bed) is 650 pounds (294.4 kg.); 520
pounds (235.9 kg) patient weight.
Use this bed only for its intended use as described in
these instructions. DO NOT use attachments not recommended by the manufacturer.
individuals may become entangled, adjust the height
of the bed rail (if applicable), or provide alternative
means of patient protection.
Once patient assessment concludes that the patient’s
condition increases the chance of entrapment, the bed
MUST be in the flat position when left unattended.
Proper patient assessment and monitoring, and proper
maintenance and use of equipment is required to
reduce the risk of entrapment. Variations in bed rail
dimensions, and mattress thickness, size or density
could increase the risk of entrapment. Visit the FDA
website at http://www.fda.gov to learn about the risks
of entrapment.
Replacement mattresses and bed side rails with dimensions different than the original equipment supplied or
specified by the bed frame manufacturer are not interchangeable. Variations in bed side rail design, width
and thickness or firmness of the mattress could cause/
contribute to entrapment. Use only authorized Drive
Medical replacement parts and/or accessories otherwise the warranty is void. Drive Medical will not be
responsible for any damage or injury that may result.
To reduce the risk of entrapment make certain that the
bed rail cross braces DO NOT exceed the width of the
mattress. Mattress MUST fit bed frame and side rails
snugly to reduce the risk of entrapment.
When operating this bed, ALWAYS ensure that the individual utilizing the bed is positioned properly within
the confines of the bed. DO NOT let any extremities
protrude over the side or between the bed rails when
performing these functions.
Drive Medical recommends that the mattress be centered on the bed frame. Otherwise, individuals may
become entangled between the bed rail and the bed
frame.
Mattress MUST fit bed frame and assist rails snugly to
reduce the risk of entrapment.
After raising/lowering the head/foot end of the bed,
SAVE THESE INSTRUCTIONS
check the distance between the bottom of the bed rail
and the mattress. If there is excessive distance between NOTE: Updated versions of this manual are available
the bottom of the bed rail and the mattress in which
on www.Drive Medical.com.
BED RAIL WARNINGS
Assist rails with dimensions different from the original
equipment supplied or specified by the bed manufacturer may not be interchangeable and may result in
entrapment or other injury.
Although bed rails are not rated to any specific weight
limitation, the bed rails may become deformed or
broken if excessive side pressure is exerted on the bed
rails. The bed rail is not an assist rail for getting into or
out of bed. DO NOT use the bed rails as push handles
when moving the bed.
Always test to make sure that the side rails are properly and securely in place before using the bed.
DO NOT install the optional bed rails without reading
and understanding all of the instructions in the instruction sheet that accompanies the bed rail kit.
DO NOT use the side rails as push handles for moving
the bed.
These bed rails are intended to prevent an individual
from inadvertently rolling out of bed. DO NOT use for
restraint purposes.
When used with a manual/electrical bed, the bed rails
DO NOT fall under any weight limitations. Bed rails
can be deformed or broken if excessive side pressure
is exerted on the bed rails. These bed rails are used for
the purpose of preventing an individual from inadvertently rolling out of bed. The bed rails are NOT
intended nor may be used for restraint purposes. If
an individual is capable of injuring himself/herself, a
physician or a healthcare professional should be consulted for alternative means of safe restraint.
ELECTRICAL WARNINGS
A safety feature of this product includes protection
against overheating caused by excessive or extended
periods of operation. Depending on the duration, this
includes multiple or repeated adjustments or the use
of multiple functions at one time. To ensure trouble
free operation, always allow a slight pause between
multiple adjustments and avoid pressing more than
one function button at a time. If thermal protection
activation should occur, the bed will not respond to
pendant commands. Given this situation, release the
pendant button and allow the bed unit to sit for several
minutes. This will allow the protection function time
to reset and restore bed function. Depending on severity of the initial overheating, this could take up to 30
minutes.
Allow a slight pause between adjustments and avoid
pressing multiple buttons at the same time. If pendant
buttons are depressed too rapidly or multiple buttons
are pressed at the same time, the desired feature may
not activate. Simply release the pendant button, permit
a slight pause and then activate the next operation.
ALWAYS remove manual crank(s) before performing
electronic functions. Otherwise, the crank(s) will turn
when the motor is on and could cause personal injury
or damage to the bed.
Always unplug the bed from the electrical outlet before cleaning.
DO NOT open assemblies such as the motors, pendant, junction boxes or gear boxes. No user serviceable parts are inside. Only qualified technicians are
permitted to repair these parts. If unqualified individuals perform any work on these beds, the warranty is
void.
DO NOT place pendant under or between objects.
This may unintentionally press the buttons and may
cause injury or damage.
Electronic equipment may be influenced by Radio
Frequency Interference (RFI). Caution should be
exercised with regard to the use of portable communications equipment in the area around such equipment.
If RFI causes erratic behavior, unplug the electric bed
IMMEDIATELY. Leave unplugged while transmission
is in progress.
Ensure all cables and cords are routed such that they
will not become entangled or pinched. Otherwise damage or injury may result.
If a button on the pendant does not release or sticks,
the bed spring will not stop moving.
If a liquid is spilled in or around the electric bed,
unplug the electric bed before cleaning. Clean up the
spill and allow the electric bed or the area around the
electric bed to dry thoroughly before using the electric
controls again.
Inspect the covering of the bed’s control panel and the
patient control panel to assure that the covering is not
cracked or damaged.
Keep all electrical cords away from heated or hot
surfaces.
Keep the cord away from heated surfaces.
NEVER operate if the unit has a damaged cord or
plug. If it is not working properly, call a qualified technician for examination and repair.
NEVER operate this bed if it has a damaged cord
or plug, if it is not working properly, if it has been
dropped, damaged, or dropped into water. Return the
bed to a service center for examination and repair.
On Full Electric beds, the Hi/Lo crank MUST be
removed before the bed is used. Failure to remove the
crank may cause damage or personal injury.
Refer servicing to qualified personnel only. Grounding reliability depends upon a properly grounded wall
outlet.
The pendant and power cords must be routed and
secured properly to ensure that the cords DO NOT become entangled, pinched and/or severed during operation of the electric bed.
Unplug from the outlet before servicing.
Unplug the power cord from its power source before
performing any maintenance on the manual/electric
bed. DO NOT unplug the power cord from the junction box. Damage to cord will result.
Use caution when disconnecting the pendant. DO
NOT press pendant buttons.
When bed is not to be used for an extended period,
unplug electric bed from the wall outlet.
When using an extension cord, use only a three wire
extension cord having at least 16 AWG (American
Wire Gauge) wire and the same or higher electrical
rating as the device being connected. Use of improper
extension cord could result in a risk of fire and electric shock. Three to two prong adapters should not be
used. Use of three prong adapters can result in improper grounding and present a shock hazard to the user.
When using nasal or masked type oxygen administering equipment, the oxygen or air tubing MUST be
routed and secured properly to ensure that the tubing
does not become entangled and/or severed during normal operation of the bed.
DO NOT use near explosive gases.
Possible fire hazard when used with oxygen administering equipment other than nasal or masked type.
Use masked or nasal type oxygen administering equipment only in conjunction with this bed. The use of
ANY other type of oxygen administering equipment
can result in a fire hazard.
Before connecting/disconnecting the connections at
the junction box, make sure the cable lock is removed
by lightly depressing on the end tabs and lifting. After
connectors are plugged in, route all cables into the
cable lock slots and snap the cable lock in place. When
installing any connectors into the junction box, be sure
the cable lock is secure after installation - otherwise,
injury or damage may occur.
DO NOT force the connector into the junction box,
otherwise - injury or damage may occur.
DO NOT unplug power cord from junction box.
DO NOT unplug power cord from motor housing.
Caja de
embalaje
Piecera
Caja de embalaje
Tubo de
tiro
¼ pulgada
(0.6 cm)
SECCIÓN DE LA PIECERA
FIGURA 6 – ENSAMBLANDO LOS EXTREMOS DE LA CAMA
Eje impulsor
Eje interior
CONECTANDO EL MOTOR DE LA CABECERA A LA CAJA DE CONEXIONES
TOTALMENTE ELÉCTRICA
INSTALANDO/ RETIRANDO LOS
CONECTORES HACIA/DE LA CAJA DE
CONEXIONES
Rueda
PARTE DE ABAJO DEL
EXTREMO DE LA PIECERA
INSTALANDO/ RETIRANDO LOS CONECTORES
HACIA/DE LA CAJA DE CONEXIONES
PARA BAJAR LA SECCIÓN DEL TAMBOR DE
RESORTES DE LA CABECERA
PARA LEVANTAR TODA LA CAMA
PARA LEVANTAR LA SECCIÓN DEL TAMBOR
DE RESORTES DE LA PIECERA
PARA BAJAR TODA LA CAMA
PARA BAJAR LA SECCIÓN DEL TAMBOR DE
RESORTES DE LA PIECERA
LEVANTANDO Y BAJANDO TODA LA CAMA
LEVANTANDO Y BAJANDO LAS SECCIONES DE
LA CABECERA Y PIECERA
Intercalaires
Intercalaire
Maillage
Boîte
Boîte
Section de pied
Tube de
traction
Vers la boîte de
raccordement
RACCORDEMENT DU MOTEUR DE LA TÊTE DE LIT À LA BOÎTE DE RACCORDEMENT
TOUT ÉLECTRIQUE
Cordon d’alimentation
TESTS DES FONCTIONS DU LIT
BRANCHEMENT /
DÉBRANCHEMENT DE LA
BOÎTE DE RACCORDEMENT
Fiches
Installation
MISE EN GARDE
Boîte de
raccordement
SECTION DE PIED DU LIT,
VUE DU DESSOUS
BRANCHEMENT / DÉBRANCHEMENT
DE LA BOÎTE DE RACCORDEMENT
DESCENDRE LE SECTION DE TÊTE DU SOMMIER.
FAIRE MONTER LE SECTION DE PIED DU SOMMIER
MONTER ET DESCENDRE LE LIT EN ENTIER
MONTER ET DESCENDRE LES SECTIONS DE PIED
ET DE TÊTE
ENTRETIEN ET VÉRIFICATIONS
99 Seaview Boulevard
Port Washington, NY 11050
Phone: 516-998-4600
Fax: 516-998-4601
www.drivemedical.com
REV3.01.22.15">
