Black & Decker BDECS300C-CA, Black + Decker BDECS300C 13A , BDECS300C Упутство за употребу

7-1/4” (184MM), 13 AMP CIRCULAR SAW
INSTRUCTION MANUAL
CATALOG NUMBER
BDECS200
BDECS300
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR
ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to http://www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
To register your new product, visit
www.BlackandDecker.com/NewOwner
DEFINITIONS: SAFETY ALERT SYMBOLS AND WORDS
This instruction manual uses the following safety alert symbols and words to alert you
to hazardous situations and your risks of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially haz­ard­ous situation which, if not avoided, may
result in minor or mod­er­ate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
General Power Tool Safety
Warnings
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a
ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI
reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the influence of drugs,
alcohol or medication. A moment of
inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off
position before connecting to power
source and/ or battery pack, picking
up or carrying the tool. Carrying
power tools with your finger on the
switch or energizing power tools that
have the switch on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the power
tool may result in personal injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair
WARNING: Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may ignite
the dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled
cords increase the risk of electric shock.
2
can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce dustrelated hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot be
controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and
tool bits, etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
b) Do not reach underneath the
workpiece. The guard cannot protect
you from the blade below the workpiece.
c) Adjust the cutting depth to the
thickness of the workpiece. Less than
a full tooth of the blade teeth should be
visible below the workpiece.
d) Never hold piece being cut in your
hands or across your leg. Secure the
workpiece to a stable platform. It is
important to support the work properly to
minimize body exposure, blade binding,
or loss of control.
e) Hold the power tool by insulated gripping
surfaces only, when performing an
operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a “live” wire will also make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
f) When ripping always use a rip fence
or straight edge guide. This improves
the accuracy of cut and reduces the
chance of blade binding.
g) Always use blades with correct size
and shape (diamond versus round) of
arbour holes. Blades that do not match
the mounting hardware of the saw will
run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade
washers or bolt. The blade washers and
bolt were specially designed for your saw, for
optimum performance and safety of operation.
Causes and Operator
Prevention of Kickback:
• Kickback is a sudden reaction to a
pinched, bound or misaligned saw blade,
causing an uncontrolled saw to lift up and
out of the workpiece toward the operator.
• When the blade is pinched or bound
tightly by the kerf closing down, the blade
stalls and the motor reaction drives the
unit rapidly back toward the operator.
• If the blade becomes twisted or
misaligned in the cut, the teeth at the
back edge of the blade can dig into the
top surface of the wood causing the
blade to climb out of the kerf and jump
back toward the operator.
Kickback is the result of saw misuse and/
or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
a) Maintain a firm grip with both hands
on the saw and position your arms to
resist kickback forces. Position your
body to either side of the blade, but not
in line with the blade. Kickback could
cause the saw to jump backwards, but
Safety Instructions for
All Saws
DANGER: Keep hands away from
cutting area and the blade. Keep your
second hand on auxiliary handle or
3
released. For all other sawing, the lower
guard should operate automatically.
d) Always observe that the lower guard is
covering the blade before placing saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade
to stop after switch is released.
kickback forces can be controlled by the
operator, if proper precautions are taken.
b) When blade is binding, or when
interrupting a cut for any reason, release
the trigger and hold the saw motionless
in the material until the blade comes to a
complete stop. Never attempt to remove
the saw from the work or pull the saw
backward while the blade is in motion or
kickback may occur. Investigate and take
corrective actions to eliminate the cause of
blade binding.
c) When restarting a saw in the
workpiece, center the saw blade in the
kerf and check that saw teeth are not
engaged into the material. If saw blade
is binding, it may walk up or kickback from
the workpiece as the saw is restarted.
d) Support large panels to minimize the
risk of blade pinching and kickback.
Large panels tend to sag under their own
weight. Supports must be placed under
the panel on both sides, near the line of
cut and near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
f) Blade depth and bevel adjusting
locking levers must be tight and
secure before making cut. If blade
adjustment shifts while cutting, it may
cause binding and kickback.
g) Use extra caution when sawing into
existing walls or other blind areas.
The protruding blade may cut objects
that can cause kickback.
Additional Safety
Instructions
• Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
• Keep your body positioned to either
side of the blade, but not in line with
the saw blade. KICKBACK could cause
the saw to jump backwards (see Causes
and Operator Prevention of Kickback
and KICKBACK).
• Avoid cutting nails. Inspect for and remove
all nails from lumber before cutting.
• Always make sure nothing interferes
with the movement of the lower blade
guard.
• Accessories must be rated for at
least the speed recommended on the
tool warning label. Wheels and other
accessories running over rated speed
can fly apart and cause injury. Accessory
ratings must always be above tool speed
as shown on tool nameplate.
• Always make sure the saw is clean
before using.
• Stop using this saw and have it properly
serviced if any unusual noise or
abnormal operation occurs.
• Always be sure all components are
mounted properly and securely before
using tool.
• Always handle the saw blade with care
when mounting or removing it or when
removing the diamond knockout.
• Always wait until the motor has reached
full speed before starting a cut.
• Always keep handles dry, clean and free
of oil and grease. Hold the tool firmly with
both hands when in use.
• Always be alert at all times, especially
during repetitive, monotonous operations.
Always be sure of position of your hands
relative to the blade.
• Stay clear of end pieces that may fall
after cutting off. They may be hot, sharp
and/or heavy. Serious personal injury
may result.
• Replace or repair damaged cords. Make
sure your extension cord is in good condition.
Use only 3-wire extension cords that have
Lower Guard Safety
Instructions
a) Check lower guard for proper closing
before each use. Do not operate the saw
if lower guard does not move freely and
close instantly. Never clamp or tie the
lower guard into the open position. If
saw is accidentally dropped, lower guard
may be bent. Raise the lower guard with the
retracting handle and make sure it moves
freely and does not touch the blade or any
other part, in all angles and depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are
not operating properly, they must be
serviced before use. Lower guard may
operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
c) Lower guard should be retracted
manually only for special cuts such
as “plunge cuts” and “compound
cuts.” Raise lower guard by retracting
handle and as soon as blade enters
the material, the lower guard must be
4
3-prong grounding-type plugs and 3-pole
receptacles that accept the tool’s plug.
• An extension cord must have
adequate wire size (AWG or American
Wire Gauge) for safety. The smaller the
gauge number of the wire, the greater
the capacity of the cable, that is 16
gauge has more capacity than 18 gauge.
An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. When using more than one
extension to make up the total length, be
sure each individual extension contains
at least the minimum wire size. The
following table shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the
gauge number, the heavier the cord.
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into
your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Cutting plastics, sap
coated wood, and other materials may
cause melted material to accumulate on the
blade tips and the body of the saw blade,
increasing the risk of blade overheating and
binding while cutting.
WARNING: Use of this tool can
generate and/or disburse dust, which may
cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate
for the dust exposure. Direct particles away
from face and body. Always operate tool in
well-ventilated area and provide for proper
dust removal. Use dust collection system
wherever possible.
Minimum Gage for Cord Sets
Total Length of Cord in Feet
0-25
26-50
51-100
101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
Ampere Rating
More Not more
American Wire Gage
Than Than
0
-6
18
16
16
14
6
-10
18
16
14
12
Volts
120V
WARNING: Blades coast after turn
off. Serious personal injury may result.
WARNING: ALWAYS wear proper
personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.
WARNING: ALWAYS use proper eye
protection. All users and bystanders must
wear proper eye protection that conforms to
ANSI Z87.1.
WARNING: ALWAYS USE SAFETY
GLASSES. Everyday eyeglasses are NOT
safety glasses. Also use face or dust mask
if cutting operation is dusty.
ALWAYS wear certified safety equipment:
• ANSI Z87.1 eye protection (CAN/CSA
Z94.3).
• ANSI S12.6 (S3.19) hearing protection.
• NIOSH/OSHA respiratory protection.
WARNING: Some dust created by
power sanding, sawing, grinding, drilling,
and other construction activities contains
chemicals known in the state of California
to cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints, crystalline silica
from bricks and cement and other masonry
products, and arsenic and chromium from
chemically-treated lumber (CCA).
Your risk from these exposures varies,
5
SYMBOLS
• The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V..................volts
mW..............milliwatts
nm...............wavelength in nonometers
A..................amperes
Hz................hertz
W.................watts
min..............minutes
or AC......alternating current
or DC....direct current
no................no load speed
................Class I Construction
(grounded)
.................earthing terminal
...............safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
reciprocation per minute
...........Read instruction manual
before use
.................Use proper respiratory
protection
................Use proper eye protection
.................Use proper hearing
protection
To Reduce the Risk of
Kickback
D
• Keep a firm grip on saw with both hands
at all times.
• Stay alert – exercise control.
• Support long overhanging materials. As
the material is cut and weakens, it will
sag, causing a pinched blade.
• Support large panels as shown (Figure A).
Material supported only at the ends
(Figure B) will lead to blade pinching.
• Avoid sawing overhead. Material can
sag and will pinch blade.
• Keep blades sharp and clean.
• Use fence or straight edge guide when
ripping. Be careful as the cut off strip can
sag or twist, closing the cut and pinching
the blade, leading to KICKBACK.
• Don’t force tool. Wood variables
such as knots, hardness, toughness,
wetness, pressure treated and freshly
cut green lumber can heavily load the
saw which can lead to stalling. Push the
saw slower when this occurs.
• Don’t remove saw from work during a
cut while the blade is moving.
• Allow saw to reach full speed before blade
contacts material to be cut. Starting the
saw with the blade against the work or
pushed forward into cut can lead to stalling
or sudden backward movement of saw.
• Never attempt to lift saw when making
a bevel cut. This leads to blade binding
and stalling.
• Always secure work to prevent
workpiece movement during cut.
• Do not try to force saw back on line if
your cut begins to go off line. This can
cause KICKBACK. Stop saw and allow
blade to coast down to a stop. Withdraw
from cut and start a new cut on the line.
• Set depth adjustment of saw such that
one tooth of the blade projects below
the workpiece as shown in (figure F).
• Do not back up a rotating blade in the
cut. Twisting the saw can cause the
back edge of the blade to dig into the
material, climb out of the work and run
back toward the operator.
• Avoid cutting nails. Inspect for and remove
all nails from lumber before cutting.
A
B
• Insure that the material to be cut is
clamped (Figure C) and solidly supported
and balanced on a strong, stable and
level work surface. Support the work so
that the wide portion of the saw shoe is on
the portion of the material that doesn’t fall
after the cut is made. Never hold cut off
piece by hand (Figure D )
C
Safety Instructions - Lasers
(BDECS300 ONLY)
DANGER: Laser radiation, avoid
direct eye exposure, serious eye injury
can result.
• Do not use optical tools such as a
telescope or transit to view the laser beam.
• Position the laser so unintentional eye
contact will be avoided.
• Do not operate the laser around children
6
or allow children to operate the laser.
• Do not disassemble. Modifying the
product in any way can increase the
risk of laser radiation.
WARNING: Use of controls or
adjustments or performance of procedures
other than those specified in this manual may
result in hazardous laser radiation exposure.
• Do not operate in explosive
atmospheres, such as in the presence
of flammable liquids, gases, or dust.
• Storeidleproductoutofreachof children
and other untrained persons. Lasers /
power tools are dangerous in the hands
of untrained users.
• Use only accessories that are
recommended by the manufacturer for
your model. Accessories that may be
suitable for one laser / power tool, may
create a risk of injury when used on
another laser / power tool.
• Repairs and servicing MUST be
performed by a qualified repair facility.
Repairs performed by unqualified
personnel could result in serious injury.
• Do not remove or deface warning
labels. Removing labels increases the
risk of exposure to radiation.
• For indoor use only.
• This product is intended for use in
a temperature range of 41°F(5°C) 104°F(40°C).
CAUTION:Use of controls or
adjustments or performance of
procedures other than those specified in
this manual may result in hazardous laser
radiation exposure.
The following laser warnings are located
on your saw.
on the nameplate. Lower voltage will cause
loss of power and can result in over-heating.
All BLACK+DECKER tools are factorytested; if this tool does not operate, check
the power supply. This tool is AC only.
INTENDED USE
This circular saw is designed for wood
cutting applications. Do not use water
feed attachments with this saw. Do not
use abrasive wheels or blades. Do not
use under wet conditions or in presence
of flammable liquids or gases. Do not cut
metal, plastic materials, concrete, masonry,
or fiber cement materials with this saw.
SAVE THESE INSTRUCTIONS
Functional Description
1. On/off switch
2. Main handle
3. Secondary handle
4. Shoe
5. Saw blade
6. Saw blade lower guard
7. Lower guard retracting lever
8. Laser (BDECS300 ONLY)
9. Bevel adjustment knob
10. Outer blade clamp washer
11. Blade retaining bolt
12. Depth adjustment lever
13. Depth scale
14. Bevel angle scale
15. Saw blade hex wrench
16. Spindle lock button
1
2
3
15
8
7
14
9
11
10
4
6
MOTOR
Be sure your power supply agrees with
nameplate marking. 120 Volts AC means
your tool will operate on standard 60 Hz
household power. Do not operate AC tools
on DC. A rating of 120 volts AC/DC means
that your tool will operate on standard 60 Hz
AC or DC power. This information is printed
5
13
12
16
7
Assembly/Adjustment Set-Up
G
WARNING: Always unplug saw
from power supply before any of the
following operations.
ADJUSTING THE DEPTH OF CUT
The depth of cut should be set according
to the thickness of the workpiece.
•Loosen the depth adjustment lever (12)
to unlock the saw shoe (4).
•Move the saw shoe into the desired
position (Figure E). The corresponding
depth of cut can be read from the depth
scale (13).
•Tighten the lever to lock the saw shoe in
place.
•Set depth adjustment of saw such that
one tooth of the blade projects below
the workpiece as shown in Figure F.
INSTALLING THE BLADE
•Keep the spindle lock button (16)
depressed and rotate the blade until the
spindle lock engages.
•Loosen and remove the blade retaining
screw (11) by turning the hex wrench
(15) counterclockwise (Figure H).
•Remove the outer washer (10).
•Place the saw blade (5) onto the spindle
shaft, making sure that the arrow on the
blade points in the same direction as the
arrow on the upper gaurd of the tool.
•Fit the outer washer on the spindle with
the larger flat surface against the blade.
•Insert the blade retaining screw into the
hole in the spindle.
•Securely tighten the blade retaining
screw by turning hex wrench clockwise
to tighten the blade retaining screw.
E
F
H
Tip of tooth
11
16
Surface of wood
ADJUSTING THE BEVEL ANGLE
This tool can be set to bevel angles
between 0° and 45°.
•Loosen the locking knob (9) to unlock
the saw shoe.
•Move the saw shoe (4) into the desired
position (Figure G). The corresponding
bevel angle can be read from the scale (14).
•Tighten the locking knob to lock the saw
shoe in place.
REMOVING THE BLADE
•Loosen and remove the blade retaining
screw (11) by turning it counterclockwise
using the hex wrench (15).
•Remove the outer washer (10).
•Remove the saw blade (5).
NOTICE: Never engage the spindle lock
while the saw is running. Never turn the
saw on while the spindle lock is engaged.
Severe damage to the saw may result.
WARNING: To reduce the risk of
serious personal injury, read, understand
and follow all important safety warnings
and instructions prior to using tool.
8
WARNING: DO NOT use tinted
glasses to enhance the laser light.
Tinted glasses will reduce overall vision
for the application and interfere with the
normal operation of the tool.
I
5
10
11
TO USE THE LASER LINE
• Mark the line that you intend to cut on
the workpiece.
• Adjust the depth and angle of cut as
required.
• Depress the saw trigger switch (1) to
project the laser beam (Figure J). Allow
the blade to reach maximum speed.
• Place the saw shoe on the workpiece.
Align the laser line with the mark on
the workpiece and slowly push the saw
forward, keeping the laser line on the mark.
15
GENERAL CUTS (IMPORTANT:
READ SAFETY WARNINGS AND
INSTRUCTIONS. )
GUARD AGAINST KICKBACK
With unit unplugged, follow all assembly,
adjustment and set up instructions.
Make sure lower guard operates. Select
the proper blade for the material to be cut.
•Measure and mark work for cutting.
•Support and secure work properly (See
Safety Rules and Instructions).
•Use appropriate and required safety
equipment (See Safety Rules).
•Secure and maintain work area (See
Safety Rules).
•With plug inserted and guard closed,
make sure switch turns saw on and off.
J
WARNING: It is important to support
the work properly and to hold the saw
firmly to prevent loss of control which
could cause personal injury. Figure C
illustrates proper hand position.
ADJUSTING THE LASER LINE
•Before making a cut, make sure the
laser line (8) is accurate. The laser
should line up in the right notch (17) of
the shoe. When the saw is beveled, the
laser should line up in the left notch (18)
as shown in the inset of Figure K.
•If the laser needs to be adjusted, use
a screwdriver to rotate the screw (19)
back and forth until the laser lines up
properly (Figure K).
OperationOPERATION
SWITCH
•To operate the tool, depress the trigger
switch (1). The tool will continue to run
as long as the trigger is depressed.
•To turn the tool off, release the trigger
switch (1). There is no provision for
locking the tool on, and the switch should
never be locked on by any other means.
K
19
LASER LINE (BDECS300 ONLY)
WARNING: LASER RADIATION.
Never aim the beam at a workpiece
with a reflective surface. Bright shiny
reflective sheet steel or similar reflective
surfaces are not recommended for laser
use. Reflective surfaces could direct the
beam back toward the operator.
DANGER: LASER RADIATION.
AVOID DIRECT EYE EXPOSURE. Do
not stare into the laser light source.
Never aim light at another person or
object other than the workpiece. Laser
light can damage your eyes.
18
17
CUTTING OPERATIONS
WARNING: To reduce the risk of
serious personal injury,always hold the
tool with both hands.
•After switching the tool on, allow the
blade to come up to full speed before
9
starting to cut
•Apply only a gentle pressure to the tool
while performing the cut.
•Always keep bottom surface of shoe in
full contact with the workpiece.
L
HINTS FOR OPTIMUM USE
•To minimize splintering of the finished
surface of the workpiece material, cut
the material with the finished surface on
the underside.
•To minimize splintering on finished
surfaces when the finished surface
cannot be placed on the underside,
such when cutting laminates, securely
clamp a sacrificial piece of plywood to
the finished surface and cut through
both materials
RIPPING
Accessory rip fences are available for this
circular saw.
Ripping is the process of cutting wide
material into narrower strips, cutting
along the grain of the material. Use an
accessory rip guide or clamp a straight
edge to the material to act as an guide
when making rip cuts.
POCKET CUTTING - FIGURE L
WARNING: Never tie the blade
guard in a raised position. Never move
the saw backwards when pocket cutting.
This may cause the unit to raise up off the
work surface which could cause injury.
A pocket cut is one that is made in a
floor, wall, or other flat surface.
•Adjust the shoe (4) so the blade cuts at
desired depth.
•Tilt the saw forward and rest front of the
shoe on material to be cut.
•Using the retracting lever (7), retract
lower blade guard to an upward
position. Lower rear of shoe until blade
(5) teeth almost touch cutting line.
•Release the blade guard (its contact with
the work will keep it in position to open
freely as you start the cut). Remove
hand from guard lever and firmly grip
secondary handle (3), as shown in
Figure L. Position your body and arm to
allow you to resist kickback if it occurs.
•Make sure blade is not in contact with
cutting surface before starting saw.
•Start the motor and gradually lower
the saw until the shoe rests flat on the
material to be cut. Advance saw along
the cutting line until cut is completed.
•Release trigger and allow blade to stop
completely before withdrawing the
blade from the material.
•When starting each new cut, repeat as
above.
WRENCH STORAGE
The hex wrench can be stored on the cord
as shown in Figure M.
M
MAINTENANCE
WARNING: Unplug tool before
installing or removing accessories, before
adjusting, or when making repairs.
Use only mild soap and damp cloth to
clean the tool. Never let any liquid get
inside the tool; never immerse any part of
the tool into a liquid.
IMPORTANT: To assure product SAFETY
and RELIABILITY, repairs, maintenance
and adjustment (other than those listed
in this manual) should be performed
by authorized service centers or other
qualified service organizations, always
using identical replacement parts.
LUBRICATION
BLACK+DECKER tools are properly
lubricated at the factory and are ready for use.
ACCESSORIES
Rip fences and other accessories are
available from BLACK+DECKER Service
Centers. To find your local service
location, call: 1-800-544-6986 or visit
www.blackanddecker.com
10
Recommended accessories for use with your
tool are available from your local retailer.
WARNING:The use of any accessory
not recommended for use with this tool
could be hazardous. Use only 7-1/4 “
(184mm) blades with 5/8” diameter arbor.
only, is to return the product to the retailer
from whom it was purchased (provided that
the store is a participating retailer). Returns
should be made within the time period of
the retailer’s policy for exchanges (usually
30 to 90 days after the sale). Proof of
purchase may be required. Please check
with the retailer for their specific return
policy regarding returns that are beyond
the time set for exchanges.
The second option is to take or send the
product (prepaid) to a BLACK+DECKER
owned or authorized Service Center for
repair or replacement at our option. Proof
of purchase may be required.
This warranty does not apply to accessories.
This warranty gives you specific legal rights
and you may have other rights which vary
from state to state or province to province.
Should you have any questions, contact the
manager of your nearest BLACK+DECKER
Service Center. This product is not intended
for commercial use.
Free Warning Label Replacement: If
your warning labels become illegible or
are missing, call 1-800-544-6986 for a
free replacement.
SERVICE INFORMATION
All BLACK+DECKER Service Centers
are staffed with trained personnel to
provide customers with efficient and
reliable power tool service. Whether you
need technical advice, repair, or genuine
factory replacement parts, contact the
BLACK+DECKER location nearest you.
To find your local service location, call:
1-800-544-6986 or visit
www.blackanddecker.com
FULL TWO-YEAR HOME USE
WARRANTY
Black & Decker (U.S.) Inc. warrants this
product for two years against any defects
in material or workmanship. The defective
product will be replaced or repaired at no
charge in either of two ways.
The first, which will result in exchanges
TROUBLESHOOTING
Problem
Possible Cause
Possible Solution
• Unit will not start.
• Cord not plugged in.
• Plug tool into a working outlet.
• Circuit fuse is blown.
• Replace circuit fuse. (If the
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a BLACK+DECKER
service center or authorized
servicer.)
• Circuit breaker is tripped.
• Reset circuit breaker. (If the
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a
BLACK+DECKER service center or
authorized servicer.)
• Cord or switch is damaged.
• Have cord or switch replaced
at BLACK+DECKER Service
Center or Authorized Servicer
For assistance with your product, visit our website www.blackanddecker.com for the location
of the service center nearest you or call the BLACK+DECKER help line at 1-800-544-6986.
TECHNICAL SPECIFICATIONS OF LASER:
Laser diode wavelength:
633-670nm (red color)
Laser Class:
2
Operating temperature:
41°F (5°C) - 104° F (40°C)
Accuracy:
+/- 1.8mm at every 300 mm
Maximum power output
1mW
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
11
SCIE CIRCULAIRES 7-1/4” (184MM), 13
AMPÈRE
MODE D’EMPLOI
NUMERO DE CATALOGUE
BDECS300, BDECS200
CONSERVER CE MODE D’EMPLOI POUR UN USAGE ULTÉRIEUR.
RÈGLES GÉNÉRALES DE
SÉCURITÉ
13
CONSIGNES DE RÈGLES
DE SÉCURITÉ POUR
TOUTES LES SCIES
14
CAUSES DE L’EFFET DE
REBOND ET PREÉVENTION
PAR L’OPÉRATEUR
DIRECTIVES DE SÉCURITÉ
SUPPLÉMENTAIRES :
SCIES CIRCULAIRES
A
B
C
D
DIRECTIVES DE SÉCURITÉ
- LASERS (BDECS300)
18
MOTEUR
CONFIGURATION DE
L’ASSEMBLAGE ET DES
RÉGLAGES
CONSERVER CES DIRECTIVES
E
1
2
3
15
8
7
14
F
9
11
10
EXTRÉMITÉ
DE LA DENT
4
6
5
SURFACE DU
BOIS
13
12
16
19
I
G
5
10
11
15
H
11
FONCTIONNEMENT
16
J
K
19
18
17
21
•
•
•
•
L
M
DÉPANNAGE
2
+/- 1,8 mm à chaque 300 m
Imported by / Importé par
Black & Decker Canada Inc.
100 Central Ave.
Brockville (Ontario) K6V 5W6
23
SIERRAS CIRCULARES DE 184MM
(7-1/4”), 13 AMPERIOS
MANUAL DE INSTRUCCIONES
CATÁLOGO N°
Visite www.BlackandDecker.com/NewOwner para registrar su nuevo producto.
LEA EL MANUAL ANTES DE DEVOLVER ESTE PRODUCTO POR
CUALQUIER MOTIVO:
CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.
SÓLO PARA USO DOMÉSTICO.
Visite www.BlackandDecker.com/NewOwner
para registrar su nuevo producto.
DEFINICIONES: SÍMBOLOS Y PALABRAS DE ALERTA DE SEGURIDAD
PRECAUCIÓN:
24
INSTRUCCIONES DE
SEGURIDAD PARA TODAS
LAS SIERRAS
CAUSAS DEL RETROCESO
Y SU PREVENCIÓN POR
PARTE DEL OPERADOR
INSTRUCCIONES DE
SEGURIDAD PARA EL
PROTECTOR INFERIOR
INSTRUCCIONES
ADICIONALES DE
SEGURIDAD
PARA REDUCIR EL
RIESGO DE RETROCESO
A
B
29
C
INSTRUCCCIONES DE
SEGURIDAD - LÁSERES
(BDECS300)
D
1
2
3
15
8
7
14
9
11
10
4
6
5
13
12
16
ENSAMBLADO/AJUSTE
CONSERVE ESTAS INSTRUCCIONES
DESCRIPCIÓN DE LAS
FUNCIONES
E
H
F
11
16
PUNTA DEL
DIENTE
SUPERFICIE DE
LA MADERA
G
I
5
10
11
15
J
FUNCIONAMIENTO
K
19
18
17
33
L
34
M
35
DETECCIÓN DE PROBLEMAS
633 a 670 nm (color rojo)
2
5°C (41°F) a 40°C (104°F)
+/- 1,8 mm cada 300 mm
36
· GARANTÍA BLACK+DECKER · BLACK+DECKER WARRANTY
. SOLAMENTE PARA PROPOSITOS DE MEXICO
Distributor Name · Sello firma del distribuidor
Date of purchase · Fecha de compra Invoice No. · No. de factura
Country · País
37
BLACK & DECKER S.A. DE C.V.
BOSQUES DE CIDROS ACCESO RADIATAS NO. 42
COL. BOSQUES DE LAS LOMAS.
05120 MÉXICO, D.F
TEL. (01 55) 5326 7100
01 800 847 2309/01 800 847 2312
Cat.No. BDECS300, BDECS200
Copyright© 2016 BLACK+DECKER
Form No. 90634818 REV01
38
September 2016
Printed in China">