Genius ROLL UP 45 تعليمات

ROLL-UP 45
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
ENGLISH
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
ATTENTION! To ensure the safety of people, it is important that you
read all the following instructions. Incorrect installation or incorrect use of the product could cause serious harm to people.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Carefully read the instructions before beginning to install the product.
Do not leave packing materials (plastic, polystyrene, etc.) within reach
of children as such materials are potential sources of danger.
Store these instructions for future reference.
This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could compromise the good condition/operation of the product and/or be a source
of danger.
GENIUS declines all liability caused by improper use or use other than that
for which the automated system was intended.
Do not install the equipment in an explosive atmosphere: the presence of
inflammable gas or fumes is a serious danger to safety.
GENIUS is not responsible for failure to observe Good Technique in the construction of the closing elements to be motorised, or for any deformation
that may occur during use.
Before attempting any job on the system, cut out electrical power and
disconnect the batteries.
The mains power supply of the automated system must be fitted with an
all-pole switch with contact opening distance of 3mm or greater. Use of a
6A thermal breaker with all-pole circuit break is recommended.
Make sure that a differential switch with threshold of 0.03 A is fitted upstream of the system.
GENIUS declines all liability as concerns safety and efficient operation of
the automated system, if system components not produced by GENIUS
are used.
For maintenance, strictly use original parts by GENIUS.
Do not in any way modify the components of the automated system.
14. The installer shall supply all information concerning manual operation of
the system in case of an emergency, and shall hand over to the user the
warnings handbook supplied with the product.
15. Do not allow children or adults to stay near the product while it is operating.
16. Keep remote controls or other pulse generators away from children, to
prevent the automated system from being activated involuntarily.
17. The application cannot be used by children, by people with reduced
physical, mental, sensorial capacity, or by people without experience or
the necessary training.
18. The User must not in any way attempt to repair or to take direct action
and must solely contact qualified GENIUS personnel or GENIUS service
centres.
19. The minimum installation height of the automated system is 2.5 m.
20. Do not, on any account, connect several motors to the same up-anddown device.
21. Do not connect two up-and-down devices to the same motor.
22. The equipment must always be visible when moving.
23. Anything not expressly specified in these instructions is not permitted.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
pag.2
2 CARATTERISTICHE TECNICHE
pag.2
3 GUIDA ALLA SCELTA DEL MOTORE
pag.2
3.1 PER AVVOLGIBILI
pag.2
3.2 PER TENDE DA SOLE
pag.2
4 INSTALLAZIONE
pag.3
4.1 ASSEMBLAGGIO DEL MOTORE TUBOLARE
pag.3
4.2 INSTALLAZIONE DEL MOTORE TUBOLARE
pag.3
pag.3
pag.4
5.1 CORRELAZIONE TRA SENSO DI ROTAZIONE RULLO E FRECCE FINECORSA
pag.4
5.2 REGOLAZIONE FINECORSA IN DISCESA
pag.4
5.3 REGOLAZIONE FINECORSA IN SALITA
pag.4
ITALIANO
INDICE
ITALIANO
MOTORI TUBOLARI ROLL-UP 45
1 DESCRIZIONE
Pos.
Fig. 1
MODELLO
ROLL-UP 45
COPPIA (Nm)
TEMPO MAX
UTILIZZO (min.)
VELOCITA’ (Rpm)
TENSIONE (V)
FREQUENZA (Hz)
POTENZA (W)
CORRENTE (A)
ROTAZIONI MAX
ALBERO MOTORE
DIAMETRO MOTORE
(mm)
LUNGHEZZA CON
ADATTATORE (mm)
INDICE DI
PROTEZIONE
2 CARATTERISTICHE TECNICHE
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
3 GUIDA ALLA SCELTA DEL MOTORE
3.1 PER AVVOLGIBILI
3.2 PER TENDE DA SOLE
SPORGENZA BRACCI (m)
NUMERO
BRACCI
2
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
Fig. 4
4.1 ASSEMBLAGGIO DEL MOTORE TUBOLARE
4.2 INSTALLAZIONE DEL MOTORE TUBOLARE
Tabella 1
MODELLO ROLL-UP 45
MISURA A (mm)
15
28
56
65
90
420
460
540
540
540
3
ITALIANO
ITALIANO
5.1 CORRELAZIONE TRA SENSO DI ROTAZIONE RULLO E FRECCE FINECORSA
5.2 REGOLAZIONE FINECORSA IN DISCESA
5.3 REGOLAZIONE FINECORSA IN SALITA
4
page.6
2 TECHNICAL SPECIFICATIONS
page.6
3 GUIDE FOR CHOOSING THE MOTOR
page.6
page.6
page.6
page.7
4.1 ASSEMBLY OF TUBULAR MOTOR
page.7
4.2 INSTALLATION OF TUBULAR MOTOR
page.7
page.7
5 ADJUSTMENT OF THE TRAVEL-LIMIT STOPS
page.8
5.1 CORRELATION BETWEEN ROLLER ROTATION DIRECTION AND TRAVEL-LIMIT ARROWS
page.8
5.2 ADJUSTMENT OF DESCENT TRAVEL-LIMIT STOP
page.8
5.3 ADJUSTMENT OF RISE TRAVEL-LIMIT STOP
page.8
CE DECLARATION OF CONFORMITY FOR MACHINES
Manufacturer:
Address:
Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALIA
Declares that:
• is built to be integrated into a machine or to be assembled with other machinery to create a machine under the
provisions of Directive 98/37/EC, and subsequent amendments 91/368/EEC, 93/44/EEC, 93/68/EEC
• conforms to the essential safety requirements of the other following EEC directives:
• 73/23/EEC and subsequent amendment 93/68/EEC.
• 89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
• furthermore, the manufacturer declares that the machinery must not be put into service until the machine into which
it will be incorporated or of which it will become a part has been identified and its conformity to the conditions of
Directive 98/37/EC, 89/392/EEC and subsequent modifications assimilated in Italian National legislation under Presidential Decree No. 459 of 24 July 1996 has been declared.
Grassobbio, 15-05-2007
The Managing Director
D. Gianantoni
Notes on reading the instruction
Read this installation manual to the full before you begin installing the product.
The symbol
indicates notes that are important for the safety of persons and for the good condition of the
automated system.
The symbol
draws your attention to the notes on the characteristics and operation of the product.
5
4 INSTALLATION
TUBULAR MOTORS ROLL-UP 45
Pos.
Fig. 1
Description
Tubular motor
Example of wheel adaptor (Accessory)
Example of crown adaptor (Accessory)
Travel-limit stop ring-nut
Travel-limit stop adjustment tool
Travel-limit stop adjustment screws
Example of motor support (Accessory)
ROLL-UP 45
MODEL
TORQUE
(Nm)
USE FREQUENCY
MAX USE
TIME (min.)
VOLTAGE (V)
CURRENT (A)
LENGTH WITH
ADAPTOR
(mm)
PROTECTION
INDEX
2 TECHNICAL SPECIFICATIONS
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
3 GUIDE FOR CHOOSING THE MOTOR
3.1 FOR ROLLER SHUTTERS
6
ARM PROTRUSION (m)
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
4 INSTALLATION
Before installing, select:
1) The wheel and crown adaptor (Fig.1 ref. ) most suitable for the type of roller to be moved.
2) The motor support most suitable for the application.
4. Install the selected motor from the electric facilities
side.
5. Secure the motorised roller, exerting light pressure on
the motor support (Fig. 5 ref. ), and on the cap support (Fig. 5 ref. ), so that the travel-limit adjustment
screws are accessible.
6. Make sure that the motorised roller is perfectly horizontal and, if necessary, modify the height of the cap
or motor supports.
1. Fit the crown adaptor (Fig.2 ref.) on the tubular motor, until it is completely inserted on the guide (Fig.2
ref.) on the travel-limit ring-nut.
2. Insert the wheel adaptor (Fig.2 ref.) on the motor
shaft and secure it with the supplied Seeger ring (Fig.2
ref.)
Fig. 5
Fig. 2
4.2 INSTALLATION OF TUBULAR MOTOR
Table 1
ROLL-UP 45 MODEL
MEASURE A (mm)
15
28
56
65
90
420
460
540
540
540
1. Drill a hole with a 3mm diam. bit on the roller (Fig.3 ref.
) at distance A (Fig.3 ref.), referring to table 1.
Fig. 6
1) Before attempting any action on the system, cut
out the electrical power supply.
2) Install an omnipolar switch on the power supply
line for the automated system, with contact opening distance of 3mm or more.
1. Connect the wires coming from the motor to an interlocked up-and-down device without reset facility
as in the lay-out of figure 6
2. Connect the up-and-down device to the power supply line as shown in Fig. 6.
3. Power up the electro-roller
4. Press the rise push-button and check if the roller rotates in the winding direction and stop the motor.
5. If the rotation direction is incorrect, cut power and
- in the up-and-down device (Fig. 6 ref. ) - change
over the black wire with the brown wire and check if
operation is correct.
6. Press the descent push-button to check operation,
and stop the motor.
Fig. 3
2. Insert the assembled tubular motor inside the roller
from the side opposite the cap, until the crown adaptor is completely inside the roller (Fig.4 ref.).
3. Secure the wheel adaptor to the roller with a 4x10
self-tapping screw inserted in the hole you had drilled,
as shown in Fig. 4 ref. .
7
Fig. 4
4.1 ASSEMBLY OF TUBULAR MOTOR
5 ADJUSTMENT OF THE TRAVEL-LIMIT STOPS
A system of electro-mechanical travel-limit stop is housed inside the GENIUS tubular motors. These stops cut power to
the motor, when the opening or closing limit of the roller-shutter is reached.
5.1 CORRELATION BETWEEN ROLLER ROTATION DIRECTION AND TRAVEL-LIMIT ARROWS
Fig. 7
To help you find the travel-limit stop adjustment screws, refer to figures 8 - 9, according to the motor installation side
(RH or LH), and to the box configuration (internal or external).
5.2 ADJUSTMENT OF DESCENT TRAVEL-LIMIT STOP
Fig. 8
1. Hold down the descent push-button
2. Using the adjustment tool (Fig.1 ref.), turn the screw of the travel-limit stop corresponding to the roller’s descent
rotation direction (Fig.8 ref.), toward the plus sign (+) to increase the travel of the roller shutter, or toward the
minus sign (-) to reduce it.
5.3 ADJUSTMENT OF RISE TRAVEL-LIMIT STOP
Fig. 9
1. Hold down the rise push-button
2. Using the adjustment tool (Fig.1 ref.), turn the screw of the travel-limit stop corresponding to the roller’s rise rotation direction (Fig.9 ref.), toward the plus sign (+) to increase the travel of the roller shutter, or toward the minus
sign (-) to reduce it.
8
page.10
2 CARACTÉRISTIQUES TECHNIQUES
page.10
3 COMMENT CHOISIR LE MOTEUR
page.10
page.10
page.10
4 INSTALLATION
page.11
4.1 ASSEMBLAGE DU MOTEUR TUBULAIRE
page.11
4.2 INSTALLATION DU MOTEUR TUBULAIRE
page.11
page.11
page.12
page.12
page.12
5.3 RÉGLAGE DU FIN DE COURSE EN MONTÉE
page.12
DÉCLARATION CE DE CONFORMITÉ POUR MACHINES
Fabricant: GENIUS S.p.A.
Adresse:
Pos.
Fig. 1
MODÈLE
ROLL-UP 45
COUPLE (Nm)
TEMPS MAXI
UTILISATION
(min.)
VITESSE (Rpm)
TENSION (V)
PUISSANCE
(W)
COURANT (A)
ROTATIONMAXI ARBRE
MOTEUR
DIAMÈTRE
MOTEUR (mm)
LONGUEUR
AVEC ADAPTATEUR (mm)
INDICE DE
PROTECTION
2 CARACTÉRISTIQUES TECHNIQUES
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
3 COMMENT CHOISIR LE MOTEUR
3.1 POUR RIDEAUX À ENROULEMENT
NOMBRE
DE BRAS
10
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
Fig. 4
Fig. 5
Fig. 2
4.2 INSTALLATION DU MOTEUR TUBULAIRE
Tableau 1
MODÈLE ROLL-UP 45
DIMENSION A (mm)
15
28
56
65
90
420
460
540
540
540
11
ÍNDICE
1 DESCRIPCIÓN
pág.14
2 CARACTERÍSTICAS TÉCNICAS
pág.14
pág.14
3.1 PARA PERSIANAS ENROLLABLES
pág.14
pág.14
4 INSTALACIÓN
pág.15
4.1 ENSAMBLAJE DEL MOTOR TUBULAR
pág.15
4.2 INSTALACIÓN DEL MOTOR TUBULAR
pág.15
pág.15
pág.16
5.1 CORRELACIÓN ENTRE EL SENTIDO DE ROTACIÓN DEL RODILLO Y LAS FLECHAS DEL FINAL DE CARRERA
pág.16
5.2 REGULACIÓN DEL FINAL DE CARRERA EN BAJADA
pág.16
pág.16
DECLARACIÓN CE DE CONFORMIDAD PARA MÁQUINAS
Fabricante:
Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALIA
Grassobbio, 15-05-2007
El Administrador Delegado
D. Gianantoni
Pos.
Fig. 1
Motor tubular
MODELO
ROLL-UP 45
PAR (Nm)
TIEMPO MÁX.
UTILIZACIÓN
(min.)
VELOCIDAD
(Rpm)
TENSIÓN (V)
FRECUENCIA
(Hz)
POTENCIA (W)
CORRIENTE (A)
DIÁMETRO
MOTOR (mm)
LONGITUD
CON ADAPTADOR (mm)
ÍNDICE DE
PROTECCIÓN
2 CARACTERÍSTICAS TÉCNICAS
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
3.2 PARA TOLDOS DE SOL
SALIENTE BRAZOS (m)
14
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
Fig. 4
4.1 ENSAMBLAJE DEL MOTOR TUBULAR
Fig. 5
Fig. 2
4.2 INSTALACIÓN DEL MOTOR TUBULAR
Tabla 1
MODELO ROLL-UP 45
MEDIDA A (mm)
15
28
56
65
90
420
460
540
540
540
15
5.1 CORRELACIÓN ENTRE EL SENTIDO DE ROTACIÓN DEL RODILLO Y LAS FLECHAS DEL
FINAL DE CARRERA
INHALT
1 BESCHREIBUNG
siete.18
2 TECHNISCHE DATEN
siete.18
siete.18
siete.18
siete.18
4 MONTAGE
siete.19
siete.19
siete.19
siete.19
siete.20
siete.20
siete.20
siete.20
Hersteller:
Erklärt, dass:
17
Pos.
Abb. 1
Rohrmotor
MODELL ROLLUP 45
MAXIMALE
EINSATZZEIT
(min.)
DREHZAHL
(Rpm)
STROM-STÄRKE
(A)
LÄNGE MIT
ADAPTER
(mm)
2 TECHNISCHE DATEN
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
18
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
Abb. 4
Abb. 5
Abb. 2
4.2 INSTALLATION DES ROHRMOTORS
Tabelle 1
MASS A (mm)
15
28
56
65
90
420
460
540
540
540
Abb. 6
19
Abb. 8
INHOUDSOPGAVE
1 BESCHRIJVING
pag.22
2 TECHNISCHE EIGENSCHAPPEN
pag.22
pag.22
pag.22
pag.22
4 INSTALLATIE
pag.23
4.1 ASSEMBLAGE VAN DE BUISVORMIGE MOTOR
pag.23
4.2 INSTALLATIE VAN DE BUISVORMIGE MOTOR
pag.23
pag.23
pag.24
pag.24
pag.24
pag.24
Adres:
Via Padre Elzi, 32 - 24050 - Grassobbio - Bergamo - ITALIE
Verklaart dat:
Grassobbio, 15-05-2007
NEDERLANDS
BUISVORMIGE MOTOREN ROLL-UP 45
1 BESCHRIJVING
Pos.
Fig. 1
Buisvormige motor
KOPPEL (Nm)
INSCHAKELFREQUENTIE
MAX. INSCHAK ELTIJD
(min.)
STROOM (A)
MAX. ROTATIE
MOTORAS
DIAMETER
MOTOR (mm)
LENGTE MET
AANPASSTUK
(mm)
2 TECHNISCHE EIGENSCHAPPEN
15
28
56
65
90
8
15
30
35
45
20%
20%
20%
20%
20%
4
4
4
4
4
17
17
17
12
12
230
230
230
230
230
50
50
50
50
50
135
200
285
275
310
0.6
0.8
1.3
1.2
1.4
16
16
16
16
16
45
45
45
45
45
450
490
570
570
570
IP 44
IP 44
IP 44
IP 44
IP 44
NEDERLANDS
AANTAL
ARMEN
22
LENGTE UITGESCHOVEN ARMEN (m)
1.5
2
2.5
3
4
2
15 Nm
30 Nm
30 Nm
30 Nm
35 Nm
3
30 Nm
30 Nm
30 Nm
30 Nm
35 Nm
4
30 Nm
35 Nm
35 Nm
35 Nm
45 Nm
5
35 Nm
35 Nm
35 Nm
45 Nm
6
35 Nm
35 Nm
45 Nm
7
45 Nm
45 Nm
Fig. 5
4.2 INSTALLATIE VAN DE BUISVORMIGE
MOTOR
Tabel 1
MODEL ROLL-UP 45
MAAT A (mm)
15
28
56
65
90
420
460
540
540
540
23
NEDERLANDS
NEDERLANDS
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi
ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per
qualsiasi altra esigenza di carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils
leaving the main features of the equipments unaltered, to undertake any modifications to holds necessary for either
technical or commercial reasons, at any time and without revising the present publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter
à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin
comprometerse a poner al día la presente publicación, todas las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht
vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf
die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment
de veranderingen aan te brengen die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke
andere productie- of commerciële eisen, waarbij de fundamentele eigenschappen van het apparaat gehandhaafd
blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: /
Stempel dealer:
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
[email protected]
www.geniusg.com
00058I0669 Rev.1">