Pioneer DMH-WC6600NEX, DMH-WC5700NEX, DMH-W4660NEX, DMH-WT76NEX, DMH-WT7600NEX, DMH-WT86NEX, DMH-WT8600NEX, DMH-WT8600NEX RDS AV Receiver, DMH-W4600NEX Installation manual

RDS AV RECEIVER
RÉCEPTEUR AV AVEC RDS
RECEPTOR AV RDS
DMH-WT8600NEX
DMH-WT7600NEX
DMH-WT86NEX
DMH-WT76NEX
DMH-WC6600NEX
DMH-WC5700NEX
DMH-W4660NEX
DMH-W4600NEX
Installation Manual
Manuel d’installation
Manual de instalación
Important safety
information
WARNING
Rear visibility systems (backup cameras)
are required in certain new vehicles sold in
the U.S. and Canada. U.S. regulations
began according to a two year phase-in on
May 1, 2016, and both the U.S. and Canada
require that all such vehicles manufactured
on or after May 1, 2018 have rear visibility
systems. Owners of vehicles equipped
with compliant rear visibility systems
should not install or use this product in
a way that alters or disables that
system's compliance with applicable
regulations. If you are unsure whether
your vehicle has a rear visibility system
subject to the U.S. or Canadian regulations,
please contact the vehicle manufacturer or
dealer.
If your vehicle has a compliant backup
camera that displays the backup view
through the factory receiver, do not use
the Pioneer receiver unless it is connected
to and displays the same view as the
factory backup camera. Connection to the
factory backup camera will require an
adaptor, sold separately. Not all vehicles
may be able to connect. Please check with
a qualified professional installer for
installation options specific to your vehicle.
Connection
Precautions
Your new product and this
manual
• Do not operate this product, any
applications, or the rear view camera
option (if purchased) if doing so will
divert your attention in any way from the
safe operation of your vehicle. Always
observe safe driving rules and follow all
existing traffic regulations. If you
experience difficulty in operating this
2 En
product, pull over, park your vehicle in a
safe location and apply the parking brake
before making the necessary
adjustments.
• Do not install this product where it may
(i) obstruct the driver’s vision,
(ii) impair the performance of any of the
vehicle’s operating systems of safety
features, including airbags, hazard lamp
buttons, or
(iii) impair the driver’s ability to safely
operate the vehicle.
In some cases, it may not be possible to
install this product because of the vehicle
type or the shape of the vehicle interior.
Important safeguards
WARNING
Pioneer does not recommend that you
install this product yourself. This product is
designed for professional installation only.
We recommend that only authorized
Pioneer service personnel, who have
special training and experience in mobile
electronics, set up and install this product.
NEVER SERVICE THIS PRODUCT YOURSELF.
Installing or servicing this product and its
connecting cables may expose you to the
risk of electric shock or other hazards, and
can cause damage to this product that is
not covered by warranty.
Precautions before
connecting the system
CAUTION
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
• Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger
compartment into the engine
compartment. If the yellow lead’s
insulation tears as a result of contact with
metal parts, short-circuiting can occur,
resulting in considerable danger.
• It is extremely dangerous to allow cables
to become wound around the steering
column or shift lever. Be sure to install
this product, its cables, and wiring away
in such so that they will not obstruct or
hinder driving.
• Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle’s moving parts,
especially the steering wheel, shift lever,
parking brake, sliding seat tracks, doors,
or any of the vehicle’s controls.
• Do not route wires where they will be
exposed to high temperatures. If the
insulation heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
• Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse
resistor or filter, etc.) may fail to work
properly.
• Never feed power to other electronic
products by cutting the insulation of the
power supply lead of this product and
tapping into the lead. The current
capacity of the lead will be exceeded,
causing overheating.
Before installing this
product
• Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or malfunction.
• To avoid shorts in the electrical system,
be sure to disconnect the (–) battery
cable before installation.
To prevent damage
WARNING
• When speaker output is used by 4
channels , use speakers over 50 W
(Maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use 1
Ω to 3 Ω speakers for this unit.
• When rear speaker output is used by 2 Ω
of subwoofer, use speakers over 70 W
(Maximum input power).
*Please refer to connection for a
connection method.
Ground wire
Other devices
(Another electronic
device in the car)
POWER AMP
Metal parts of car’s
body
*1 Not supplied for this unit
• When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
• When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
• This product cannot be installed in a
vehicle without ACC (accessory) position
on the ignition switch.
No ACC position
• To avoid short-circuiting, cover the
disconnected lead with insulating tape. It
is especially important to insulate all
unused speaker leads, which if left
uncovered may cause a short circuit.
• For connecting a power amp or other
devices to this product, refer to the
manual for the product to be connected.
• The graphical symbol
placed on
the product means direct current.
Notice for the blue/
white lead
Rear panel (main
terminals)
▶DMH-WT8600NEX/DMHWT7600NEX/DMH-WT86NEX/DMHWT76NEX/DMH-WC6600NEX/DMHWC5700NEX
• When the ignition switch is turned on
(ACC ON), a control signal is output
through the blue/white lead. Connect to
an external power amp’s system remote
control terminal, the auto-antenna relay
control terminal, or the antenna booster
power control terminal (max. 300 mA 12
V DC). The control signal is output
through the blue/white lead, even if the
audio source is switched off.
Important
When this product is in [Power OFF] mode,
the control signal is also turned off. If
[Power OFF] mode is canceled, the control
signal is output again and the antenna is
extended with the auto antenna function
(if the antenna is being used). Be careful so
that the extended antenna does not come
into contact with any obstacles.
Refer to the instruction manual for the
iDataLink or Metra adaptor (sold
separately).
Monitor cable connector*
Connect to LCD screen.
Antenna jack
This product
Pre out supply
Power supply
Fuse (10A)
Wired remote input
Hard-wired remote control adaptor can
be connected (sold separately).
SiriusXM® Connect Vehicle Tuner
Refer to the instruction manual for
SiriusXM Connect Vehicle Tuner (sold
separately).
English
• The black lead is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire
first. Ensure that the ground wire is
properly connected to metal parts of the
car’s body. The ground wire of the power
amp and the one of this unit or any other
device must be connected to the car
separately with different screws. If the
screw for the ground wire loosens or falls
out, it could result in fire generation of
smoke or malfunction.
* Monitor cable and connector are in the front
panel. (DMH-WT8600NEX, DMH-WT7600NEX,
DMH-WT86NEX, DMH-WT76NEX)
NOTES
▶DMH-W4660NEX/DMH-W4600NEX
• Before using and/or connecting the
iDatalink Maestro adaptor (sold
separately), you will need to first flash the
Maestro module with the appropriate
vehicle and head unit firmware. You can
find the device number that is required
for the activation on the followings (refer
to the Operation Manual.):
– The label on the packaging of this
product
– The label on this product
– The [Firmware Information] screen
• When the iDatalink Maestro adaptor is
connected, use the microphone of this
unit to perform voice operations for
Apple CarPlay, Android Auto, or Amazon
Alexa.
• SiriusXM and all related marks and logos
are trademarks of Sirius XM Radio, Inc. All
rights reserved.
GPS antenna 3.55 m (11 ft. 8 in.)
Microphone 3 m (9 ft. 10-1/8 in.)
iDatalink or Metra adaptor input
En
3
Power cord
WARNING
IMPROPER CONNECTION MAY RESULT IN
SERIOUS DAMAGE OR INJURY
INCLUDING ELECTRICAL SHOCK, AND
INTERFERENCE WITH THE OPERATION
OF THE VEHICLE'S ANTILOCK BRAKING
SYSTEM, AUTOMATIC TRANSMISSION
AND SPEEDOMETER INDICATION.
connection enables the unit to sense
whether the car is moving forward or
backward.
Pink
Car speed signal input
Blue/white
Connect to system control terminal of
the power amp (max. 300 mA 12 V DC).
Light green
Used to detect the ON/OFF status of the
parking brake. This lead must be
connected to the power supply side of
the parking brake switch.
If this connection is made incorrectly
or omitted, certain functions of this
product will be unusable.
Power supply side
Parking brake switch
Ground side
NOTE
The position of the speed detection circuit
and the position of the parking brake
switch vary depending on the vehicle
model. For details, consult your authorized
Pioneer dealer or an installation
professional.
Speaker leads
To power supply
Power cord
Yellow
To terminal supplied with power
regardless of ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Violet/white
Of the two lead wires connected to the
back lamp, connect the one in which
the voltage changes when the gear shift
is in the REVERSE (R) position. This
4 En
Perform these connections when using a
subwoofer without the optional amplifier.
To power supply
Power cord
Left
Right
Front speaker (STD) or high range
speaker (NW)
Rear speaker (STD) or middle range
speaker (NW)
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Subwoofer (4 Ω)
When using a subwoofer of 2 Ω, be sure
to connect the subwoofer to the violet
and violet/black leads of this unit. Do
not connect anything to the green and
green/black leads.
Not used.
Subwoofer (4 Ω) × 2
NOTES
• When a subwoofer is connected to this
product instead of a rear speaker, change
the rear output setting in the initial
setting. The subwoofer output of this
product is monaural.
For details, refer to the Operation Manual.
• With a two-speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
Power amp (sold separately)
Important
The speaker leads are not used when this connection is in use.
Rear speaker (STD)
Middle range speaker (NW)
Front speaker (STD)
High range speaker (NW)
Subwoofer (STD)
Low range speaker (NW)
English
NOTE
Select the appropriate speaker mode between standard mode (STD) and network mode
(NW). For details, refer to the Operation Manual.
Subwoofer output (SUBWOOFER OUTPUT) 23 cm (9 in.) (STD)
Low range output (NW)
RCA cable (sold separately)
Power amp
Front output (FRONT OUTPUT) 15 cm (5-7/8 in.) (STD)
High range output (NW)
Rear output (REAR OUTPUT) 15 cm (5-7/8 in.) (STD)
Middle range output (NW)
Yellow/black (MUTE)
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on
that equipment. If not, keep the Audio Mute lead free of any connections.
Pre out cord
To pre out supply
System remote control
Connect to Blue/white cable (max. 300 mA 12 V DC).
En
5
iPhone and
smartphone
NOTES
• For details on how to connect an external
device using a separately sold cable, refer
to the manual for the cable.
• For details concerning the connection,
operations and compatibility of the
iPhone, refer to the Operation Manual.
• For details concerning the connection
and operations of the smartphone, refer
to the Operation Manual.
• The supplied USB Type-C® cable and the
USB Type-C to USB Type-A adaptor are for
connecting a USB storage device to this
unit only. Do not use the cable and the
adaptor for other products or purposes.
TIP
When a USB Type-C to Lightning
connector cable (Apple Inc. product) (sold
separately) is used to connect this unit to
an iPhone that supports USB-PD, quick
charging is performed for the iPhone.
NOTE
When you use a USB Type-C to Lightning
connector cable (Apple Inc. product) (sold
separately), follow the instructions
provided with the cable.
iPhone
This product
USB Type-C port
USB Type-C cable 1.5 m (4 ft. 11 in.)
USB Type-C to USB Type-C interface
cable (CD-CCU500) (sold separately)
Smartphone
This product
USB Type-C port
USB Type-C cable 1.5 m (4 ft. 11 in.)
USB Type-C to USB Type-A adaptor
USB interface cable for iPhone (CD-IU52)
(sold separately)
iPhone
6 En
TIPS
• Use the supplied USB Type-C to USB
Type-A adaptor with a USB Type-A to
micro USB B cable (CD-MU200) (sold
separately) if your smartphone has a
micro USB B port.
• When a USB Type-C to USB Type-C cable
(sold separately) is used to connect this
unit to a smartphone, quick charging is
performed.
NOTES
• If you use a cable other than those
suggested in the illustration, the main
unit may not function properly.
• Android is a trademark of Google LLC.
Camera
When you use the rear view camera, the
rear view image is automatically switched
from the video by moving the shift lever to
REVERSE (R). Camera View mode also
allows you to check what is behind you
while driving.
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE
MAY RESULT IN INJURY OR DAMAGE.
CAUTION
• The screen image may appear reversed.
• With the rear view camera you can keep
an eye on trailers, or back into a tight
parking spot. Do not use for
entertainment purposes.
• Objects in rear view may appear closer or
more distant than in reality.
• The image area of full-screen images
displayed while backing or checking the
rear of the vehicle may differ slightly.
This product
Pre out supply
Power supply
To pre out supply
To power supply
Pre out cord
Power cord
Violet/white (REVERSE-GEAR SIGNAL
INPUT)
Brown (REAR VIEW CAMERA IN) 23 cm
(9 in.)
Yellow* (SECOND CAMERA INPUT) 23
cm (9 in.)
Rear view camera (ND-BC8) (sold
separately)
To video output
RCA power supply cable (supplied with
ND-BC8)
RCA cable (sold separately)
View camera (sold separately)
* Not available for DMH-W4600NEX
NOTES
Using an AUX input
NOTE
The appropriate setting is required to use
the external video component. For details,
refer to the Operation Manual.
NOTE
The terms HDMI, HDMI High-Definition
Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc.
Rear display
English
• Connect only the rear view camera to
brown cable. Do not connect any other
equipment.
• Some appropriate settings are required
to use rear view cameras. For details, refer
to the Operation Manual.
RCA cables (sold separately)
To video output
To audio output
External video component (sold
separately)
CAUTION
Be sure to use a mini-jack AV cable (sold
separately) for wiring. If you use other
cables, the wiring position might differ
resulting in disturbed images and sounds.
L : Left audio (White)
R : Right audio (Red)
V : Video (Yellow)
G : Ground
Using an HDMI™ input
This product
Pre out supply
To pre out supply
Pre out cord
AUX input (AUX IN) 15 cm (5-7/8 in.)
Mini-jack AV cable (sold separately)
Yellow
Red, white
This product
Micro HDMI port
Micro HDMI to HDMI cable (sold
separately)
HDMI device (sold separately)
This product
Pre out supply
To pre out supply
Pre out cord
Yellow (REAR MONITOR OUTPUT) 30
cm (11-7/8 in.)
RCA cable (sold separately)
To Video input
Rear display with RCA input (sold
separately)
En
7
WARNING
NEVER install the rear display in a location
that enables the driver to watch the video
source while driving.
This product’s rear video output is for
connection of a display to enable
passengers in the rear seats to watch the
video source.
Installation
Precautions before
installation
CAUTION
• Never install this product in places where,
or in a manner that:
– Could injure the driver or passengers if
the vehicle stops suddenly.
– May interfere with the driver’s operation
of the vehicle, such as on the floor in
front of the driver’s seat, or close to the
steering wheel or shift lever.
• To ensure proper installation, be sure to
use the supplied parts in the manner
specified. If any parts are not supplied
with this product, use compatible parts in
the manner specified after you have the
part compatibility checked by your
dealer. If parts other than supplied or
compatible ones are used, they may
damage internal parts of this product or
they may work loose and the product
may become detached.
• It is extremely dangerous to allow cables
to become wound around the steering
column or shift lever. Be sure to install
this product, its cables, and wiring away
in such so that they will not obstruct or
hinder driving.
• Make sure that leads cannot get caught
in a door or the sliding mechanism of a
seat, resulting in a short circuit.
• Please confirm the proper function of
your vehicle’s other equipment after
installation of this product.
• Do not install this product where it may
(i) obstruct the driver’s vision,
(ii) impair the performance of any of the
vehicle’s operating systems or safety
8 En
features, including airbags, hazard lamp
buttons or
(iii) impair the driver’s ability to safely
operate the vehicle.
• Never install this product in front of or
next to the place in the dashboard, door,
or pillar from which one of your vehicle’s
airbags would deploy. Please refer to your
vehicle’s owner’s manual for reference to
the deployment area of the frontal
airbags.
Before installing
• Consult with your nearest dealer if
installation requires drilling holes or
other modifications of the vehicle.
• Before making a final installation of this
product, temporarily connect the wiring
to confirm that the connections are
correct and the system works properly.
Installation notes
• Do not install this product in places
subject to high temperatures or
humidity, such as:
– Places close to a heater, vent or air
conditioner.
– Places exposed to direct sunlight, such
as on top of the dashboard.
– Places that may be exposed to rain,
such as close to the door or on the
vehicle’s floor.
• Install this product horizontally on a
surface within 0 to 40 degrees tolerance
(within 5 degrees to the left or right).
Improper installation of the unit with the
surface tilted more than these tolerances
increases the potential for errors in the
vehicle’s location display, and might
otherwise cause reduced display
performance.
5 cm
• Do not forcibly insert this unit into the
dashboard/console when installing.
Applying excessive force to the
connectors (HDMI and USB Type-C) may
cause a malfunction.
• The cords must not cover up the area
shown in the figure below. This is
necessary to allow the amplifiers to
radiate freely. (DMH-WC6600NEX/DMHWC5700NEX)
▶DMH-WT8600NEX/DMHWT7600NEX/DMH-WT86NEX/DMHWT76NEX
English
• When installing, to ensure proper heat
dispersal when using this unit, make sure
you leave ample space behind the rear
panel and wrap any loose cables so they
are not blocking the vents.
Installation using the
screw holes on the side
of this product
Installation tips
The following procedure describes how to
install this product with an LCD screen
attached to the unit. Depending on the
vehicle or installation location, you may
need to adjust the mounting position of
the LCD screen in order to prevent
impairment of vehicle driving operations.
For details on the mounting LCD screen
dimensions, refer to The adjusting position
and mounting dimension of the display
(page 12) before installing.
WARNING
Do not use a mounting sleeve to install this
unit to prevent it from popping out or
rattling.
1 Adjust the front-back position of the
front panel by removing the flush
surface screws on the front edge of the
unit ( ) then fix the face panel by
using the screw ( ) (optional).
Depending on the vehicle, the frontback position of the front panel may
need to be adjusted to mount the LCD
screen. Slide the face panel to the front
before installing the unit to the vehicle.
3
2
Screw
Fasten this product to the factory
radio-mounting bracket.
Position this product so that its screw
holes are aligned with the screw holes
of the bracket, and tighten the screws at
three locations on each side.
Factory radio-mounting bracket
If the pawl interferes with
installation, you may bend it down
out of the way.
Dashboard or console
Binding head screw (8 mm) or flush
surface screw
Be sure to use the screws supplied
with this product.
Fasten the LCD screen mounting
bracket to the main unit at the suitable
position.
TIP
The amount of this unit's protrusion from
the dashboard/console can be adjusted by
shifting the position of the screw hole of
this unit to the factory radio-mounting
bracket.
LCD screen mounting bracket
Binding head screw (4 mm × 6 mm)
TIP
The mounting left-center-right position of
the LCD screen mounting bracket can be
changed depending on the vehicle or
installation location of the main unit.
Do not cover this area
En
9
them to this unit ( ). After that,
connect the monitor cable to the LCD
screen ( ).
4
Detach the monitor cable cover from
the LCD screen ( ), then connect the
monitor cable to the LCD screen ( ).
After that, attach the LCD screen with
adjusting the up-down position ( ) to
this unit by using the screws each side
( ).
Monitor cover
Machine screw (2 mm × 4 mm)
NOTES
• Be careful not to lose the small screws
(2 mm × 4 mm) for attaching the
monitor cover.
• It is recommended that you use a
magnetic screwdriver when attaching
the monitor cover.
• Two spare screws (2 mm × 4 mm) for
attaching the monitor cover are
included.
▶DMH-WC6600NEX/DMH-WC5700NEX
5
Monitor cover
Binding head screw (4 mm × 12 mm)
Secure the monitor cable to the hook
on the back of the LCD screen then
attach the monitor cover ( ) by using
the screws ( ).
2
Installation tips
The following procedure describes how to
use the supplied parts to install this
product with the LCD screen attached to
the unit. It is also possible to install this
product so that the LCD screen is separate
from the unit. For details, visit the Pioneer
website for your region.
Side bracket (for attaching LCD
screen to unit)
Binding head screw (5 mm)
Be sure to use the screws supplied
with this product.
Monitor cable
Attach the monitor cable to the unit
with heat resistant tape (sold
separately).
Fasten this product to the factory
radio-mounting bracket.
Position this product so that its screw
holes are aligned with the screw holes
of the bracket, and tighten the screws at
three locations on each side.
Use either the binding head screws or
flush surface screws, depending on the
shape of the bracket’s screw holes.
TIP
For some types of vehicles, it is necessary
to use an installation kit (sold separately)
when installing. For details, visit the
Pioneer website for your region.
1
10 En
First attach the supplied side brackets
to the LCD screen ( ), then attach
The amount of this unit's protrusion from
the dashboard/console can be adjusted by
shifting the position of the screw hole of
this unit to the factory radio-mounting
bracket.
Factory radio-mounting bracket
If the pawl interferes with
installation, you may bend it down
out of the way.
Dashboard or console
Binding head screw (8 mm) or flush
surface screw
Be sure to use the screws supplied
with this product.
▶DMH-W4600NEX/DMH-W4600NEX
1
Fasten this product to the factory
radio-mounting bracket.
Position this product so that its screw
holes are aligned with the screw holes
of the bracket, and tighten the screws at
three locations on each side.
Use either the truss head screws (5 mm
× 9 mm) or flush surface screws (5 mm ×
9 mm), depending on the shape of the
bracket’s screw holes.
TIP
The amount of this unit's protrusion from
the dashboard/console can be adjusted by
shifting the position of the screw hole of
this unit to the factory radio-mounting
bracket.
result in a short circuit or malfunction and
permanent damage to this product.
When installing the antenna inside the vehicle (on the dashboard or
rear shelf)
Installation notes
WARNING
Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as
doing so may interfere with the proper functioning of such sensors or vents and may
compromise the ability of the metal sheet under the GPS antenna to properly and securely
affix to the dashboard.
English
• The antenna should be installed on a
level surface where radio waves will be
blocked as little as possible. Radio waves
cannot be received by the antenna if
reception from the satellite is blocked.
Make sure the surface is free of
moisture, dust, grime, oil, etc.,
before affixing the metal sheet.
Factory radio-mounting bracket
If the pawl interferes with
installation, you may bend it down
out of the way.
Dashboard or console
Truss head screw or flush surface
screw
Be sure to use the screws supplied
with this product.
Installing the GPS
antenna
CAUTION
Do not cut the GPS antenna lead to
shorten it or use an extension to make it
longer. Altering the antenna cable could
Dashboard
Rear shelf
• When installing the GPS antenna inside
the vehicle, be sure to use the metal
sheet provided with your system. If this is
not used, the reception sensitivity will be
poor.
• Do not cut the accessory metal sheet.
This would reduce the sensitivity of the
GPS antenna.
• Take care not to pull the antenna lead
when removing the GPS antenna. The
lead may become detached.
• Do not paint the GPS antenna, as this
may affect its performance.
GPS antenna
Metal sheet
Peel off the protective sheet on the rear.
Double-sided tape
Clamps
Use clamps to secure the lead where necessary inside the vehicle.
NOTES
• Affix the metal sheet on the surface as level as possible where the GPS antenna faces the
window.
• Affix the GPS antenna on the metal sheet using the double-sided tape.
• The metal sheet contains a strong adhesive which may leave a mark on the surface if it is
removed.
• When attaching the metal sheet, do not cut it into small pieces.
• Some models use window glass that does not allow signals from GPS satellites to pass
through. On such models, install the GPS antenna on the outside of the vehicle.
En
11
Installing the
microphone
The adjusting position
and mounting
dimension of the
display
• Install the microphone in a place where
its direction and distance from the driver
make it easiest to pick up the driver’s
voice.
• Be sure to turn off (ACC OFF) the product
before connecting the microphone.
• Depending on the vehicle model, the
microphone cable length may be too
short when you mount the microphone
on the sun visor. In such cases, install the
microphone on the steering column.
▶DMH-WT8600NEX/DMHWT7600NEX/DMH-WT86NEX/DMHWT76NEX
Microphone clip
Clamps
Use separately sold clamps to secure
the lead where necessary inside the
vehicle.
Install the microphone on the sun visor
when it is in the up position. It cannot
recognize the driver’s voice if the sun
visor is in the down position.
Mounting on the sun visor
1
Fit the microphone lead into the
groove.
Installation on the steering
column
1
2
Microphone lead
Groove
Attach the microphone clip to the sun
visor.
2
12 En
Detach the microphone base from the
microphone clip by sliding the
microphone base while pressing the
tab.
Tab
Microphone base
Mount the microphone on the
steering column.
Double-sided tape
Clamps
Use separately sold clamps to secure
the lead where necessary inside the
vehicle.
NOTE
Install the microphone on the steering
column, keeping it away from the steering
wheel.
Adjusting the microphone angle
The microphone angle can be adjusted.
The mounting position of this unit’s display
can be adjusted (front-back/up-down/
right-left/angle). When mounting the
display, adjust the mounting position and
dimensions so that your view is clear and it
does not impair your driving.
WARNING
Make sure that none of the following
conditions exist when mounting the
display. Otherwise, an accident may occur.
• It impairs the operation of the steering
wheel and levers (shift lever, windshield
wiper switch, turn signal switch, etc.).
• It impairs the operation of the airbags.
• It significantly impairs the operation of
the hazard switch.
• It impairs the ability to identify or operate
other control switches.
• You are unable to see gauges, meters or
warning indicators.
• It interferes with in-vehicle devices
(switches, panel, glove compartment, cup
holder, etc.).
Depending on the vehicle, the display may
hinder access to the glove compartment or
cup holder, or it may block the air
conditioner vents.
Display mounting dimensions
and adjustable positions
▶Front-back position
▶Left-right position
DMH-WT7600NEX/DMH-WT76NEX
DMH-WT8600NEX/DMH-WT86NEX
Center
Center
Front
English
75 (3)
38.1 (1-1/2)
115.4 (4-1/2)
128.2 (5)
128.2 (5)
mm (in.)
115.4 (4-1/2)
mm (in.)
Left
Left
158.2 (6-1/4)
98.2 (3-7/8)
145.4 (5-3/4)
mm (in.)
55 (2-1/8)
mm (in.)
mm (in.)
Back
Right
Right
18.1 (1/4)
98.2 (3-7/8)
85.4 (3-3/8)
158.2 (6-1/4)
mm (in.)
85.4 (3-3/8)
145.4 (5-3/4)
mm (in.)
mm (in.)
En
13
Adjustable display angles and up-down positions
Mounting dimension with the angle range of the display
WARNING
Keep hands and fingers clear of this product when adjusting the LCD screen angle. Be
especially cautious of children’s hands and fingers.
▶Front angle range
Angle range of front position
B
60˚
15˚
A
15 (5/8)
30 (1-1/8)
45 (1-3/4)
60 (2-3/8)
mm (in.)
NOTE
Certain positions cannot be adjusted and held depending on the up-down position and the
front-back position. For details, refer to Mounting dimension with the angle range of the
display (page 14).
A
0
B
60˚
-15
(-5/8)
-30
(-1-1/8)
-45
(-1-3/4)
35˚
-15˚
-60
(-2-3/8)
mm (in.)
14 En
DMH-WT8600NEX/DMH-WT86NEX
Angle 60˚
DMH-WT7600NEX/DMH-WT76NEX
Angle 35˚
Angle -15˚
Angle 60˚
A’
A’
A’
A’
C
A
C
C
A
English
C
C
C
A
A
A
A
B’
B
B’
B
A’
B
B’
C
A
A’
B
B’
C
A
A’
B
B’
B
B’
B
A
0
Angle -15˚
A’
A’
A
Angle 35˚
B’
B
B’
C
A
A’
B
B’
B
C
A
B’
A’
B
B’
C
C
58.3 166.1 -14.8 39.4 33.4 107.3 137.3 -12.5 53.4 35.9 149.0 34.6 7.7 72.4 14.3
(2-1/4) (6-1/2) (-1/2) (1-1/2) (1-1/4) (4-1/4) (5-3/8) (-1/2) (2-1/8) (1-3/8) (5-7/8) (1-3/8) (1/4) (2-7/8) (1/2)
76.3
(3)
A’
B’
B
-15
(-5/8)
95.0 128.7 -24.8 44.8 27.3 134.6 38.4 -6.8
(1) (1-3/4) (1) (5-1/4) (1-1/2) (-1/4)
(3-3/4) (5)
-30
(-1-1/8)
82.7 120.1 -37.1 36.2 18.7 120.1 42.3 -21.2 80.2 22.1
(3-1/4) (4-3/4) (1-1/2) (1-3/8) (3/4) (4-3/4) (1-5/8) (-7/8) (3-1/8) (7/8)
-45
(-1-3/4)
70.5 111.5 -49.4 27.6
(2-3/4) (4-8/3) (-1-7/8) (1)
10.1 105.6 46.2 -35.7 84.1 26.0
(3/8) (4-1/8) (1-3/4) (-1-3/8) (3-1/4) (1)
-60
(-2-3/8)
58.2 102.9 -61.7 19.0
(2-1/4) (4) (-2-3/8) (3/4)
1.5 91.1 50.1
(1/8) (3-5/8) (2)
18.2
(3/4)
-50.2 88.0 29.9
(-2) (3-1/2) (1-1/8)
0
50.6
(2)
152.6 -14.8 39.4 33.4 94.6 128.4 -12.5 53.4 35.9 134.1 38.6 7.7 72.4 14.3
(6) (-1/2) (1-1/2) (1-1/4) (3-3/4) (5) (-1/2) (2-1/8) (1-3/8) (5-1/4) (1-1/2) (1/4) (2-7/8) (1/2)
76.3
(3)
-15
(-5/8)
82.3 119.8 -24.8 44.8 27.3 119.6 42.5 -6.8
(3-1/4) (4-5/8) (1) (1-3/4) (1) (4-5/8) (1-5/8) (-1/4)
-30
(-1-1/8)
70.1 111.2 -37.1 36.2 18.7 105.1 46.3 -21.2 80.2 22.1
(2-3/4) (4-3/8) (1-1/2) (1-3/8) (3/4) (4-1/8) (1-3/4) (-7/8) (3-1/8) (7/8)
-45
(-1-3/4)
57.8 102.6 -49.4 27.6
(2-1/4) (4) (-1-7/8) (1)
10.1 90.6 50.2 -35.7 84.1 26.0
(3/8) (3-1/2) (2) (-1-3/8) (3-1/4) (1)
-60
(-2-3/8)
45.5 94.0 -61.7 19.0
(1-3/4) (3-3/4) (-2-3/8) (3/4)
1.5
(1/8)
18.2
(3/4)
76.1 54.1 -50.2 88.0 29.9
(3) (2-1/8) (-2) (3-1/2) (1-1/8)
mm (in.)
mm (in.)
En
15
▶Back angle range
DMH-WT8600NEX/DMH-WT86NEX
Angle 60˚
Angle range of back position
Angle 25˚
B
Angle -15˚
A’
A
A’
A’
C
C
C
A
A
A
B’
B
A
0
A
0
60˚
-30
(-1-1/8)
25˚
B’
58.3 146.1 -14.8 19.4
(2-1/4) (5-3/4) (-1/2) (3/4)
C
A
A’
B
B’
B’
B
C
A
A’
13.4 122.7 100.3 -9.9 38.5 16.7 149.0 14.6
(1/2) (4-3/4) (3-7/8) (3/8) (1-1/2) (5/8) (5-7/8) (1/2)
B
B’
C
7.7
(1/4)
52.4 -5.7
(2) (-1/4)
-15
(-5/8)
109.1 94.0 -23.5 32.2 10.4 134.6 18.4 -6.8 56.3 -1.8
(4-1/4) (3-3/4) (-7/8) (1-1/4) (3/8) (5-1/4) (3/4) (-1/4) (2-1/4) (-1/8)
-30
(-1-1/8)
95.5 87.7 -37.1 25.8
(3-3/4) (3-3/8) (1-1/2) (1)
-45
(-1-3/4)
81.9 81.3 -50.7 19.5 -2.3 105.6 26.2 -35.7 64.1 6.0
(3-1/4) (3-1/4) (-2) (3/4) (-1/8) (4-1/8) (1) (-1-3/8) (2-1/2) (1/4)
-60
(-2-3/8)
68.3 75.0 -64.3 13.2 -8.6 91.1 30.1 -50.2 68.0 9.9
(2-5/8) (3) (-2-1/2) (1/2) (-3/8) (3-5/8) (1-1/8) (-2) (2-5/8) (3/8)
4.1 120.1 22.3 -21.2 60.2 2.1
(1/4) (4-3/4) (7/8) (-7/8) (2-3/8) (1/8)
-15˚
-60
(-2-3/8)
mm (in.)
mm (in.)
16 En
B
B’
B
-15
(-5/8)
-45
(-1-3/4)
A’
B
DMH-WT7600NEX/DMH-WT76NEX
Angle 60˚
Angle 25˚
Angle -15˚
A’
A’
A’
C
C
English
C
A
A
A
B’
B
A
0
A’
B
B’
50.6 132.6 -14.8 19.4
(2) (5-1/4) (-1/2) (3/4)
C
B’
B
A
A’
B
B’
B’
B
C
A
A’
13.4 108.6 93.8 -9.9 38.5 16.7 134.1 18.6
(1/2) (4-1/4) (3-5/8) (3/8) (1-1/2) (5/8) (5-1/4) (3/4)
B
B’
C
7.7
(1/4)
52.4 -5.7
(2) (-1/4)
-15
(-5/8)
95.0 87.5 -23.5 32.2 10.4 119.6 22.5 -6.8 56.3 -1.8
(3-3/4) (3-3/8) (-7/8) (1-1/4) (3/8) (4-5/8) (7/8) (-1/4) (2-1/4) (-1/8)
-30
(-1-1/8)
81.4 81.1 -37.1 25.8
(3-1/4) (3-1/4) (1-1/2) (1)
-45
(-1-3/4)
67.8 74.8 -50.7 19.5 -2.3 90.6 30.2 -35.7 64.1 6.0
(2-5/8) (2-7/8) (-2) (3/4) (-1/8) (3-1/2) (1-1/8) (-1-3/8) (2-1/2) (1/4)
-60
(-2-3/8)
54.2 68.4 -64.3 13.2 -8.6
(2-1/8) (2-5/8) (-2-1/2) (1/2) (-3/8)
4.1 105.1 26.3
(1/4) (4-1/8) (1)
-21.2 60.2 2.1
(-7/8) (2-3/8) (1/8)
76.1 34.1 -50.2 68.0 9.9
(3) (1-3/8) (-2) (2-5/8) (3/8)
mm (in.)
NOTES
• Where there are no numbers in the table, this indicates that the display cannot be
adjusted and held with that angle and dimensions.
• The displayed angle range is the movable range of this unit, and it may vary depending on
the vehicle in which the unit is installed.
En
17
2 Fr
Fil de masse
AMPLIFICATEUR DE
PUISSANCE
Position ACC
▶DMH-W4660NEX/DMH-W4600NEX
Fr
3
Cordon d’alimentation
ATTENTION
UNE CONNEXION INAPPROPRIÉE
RISQUE D’ENTRAÎNER DES DOMMAGES
OU BLESSURES GRAVES, INCLUANT UNE
DÉCHARGE ÉLECTRIQUE, ET DES
INTERFÉRENCES AVEC LE
FONCTIONNEMENT DU SYSTÈME DE
FREINAGE ANTIBLOCAGE, LA BOÎTE DE
VITESSE AUTOMATIQUE ET LES
INDICATIONS DU COMPTEUR DE
VITESSE DU VÉHICULE.
4 Fr
REMARQUE
Fr
5
CONSEIL
iPhone
6 Fr
REMARQUES
REMARQUES
Fr
7
REMARQUE
8 Fr
5 cm
9
3
2
CONSEIL
10 Fr
4
▶DMH-WC6600NEX/DMH-WC5700NEX
5
1
2
CONSEIL
▶DMH-W4600NEX/DMH-W4600NEX
1
Fr
11
1
1
2
REMARQUES
12 Fr
2
REMARQUE
DMH-WT8600NEX/DMH-WT86NEX
Avant
75
38,1
128,2
128,2
mm
Gauche
158,2
98,2
mm
mm
Droite
18,1
98,2
158,2
mm
mm
Fr
13
DMH-WT7600NEX/DMH-WT76NEX
15˚
115,4
mm
Gauche
15
30
45
60
145,4
85,4
85,4
145,4
mm
14 Fr
mm
REMARQUE
DMH-WT8600NEX/DMH-WT86NEX
Angle 60˚
Angle 35˚
Angle -15˚
A’
A’
A’
C
C
A
A’
B
B’
C
107,3 137,3 -12,5
53,4
35,9
149,0 34,6
7,7
72,4
14,3
-15
95,0 128,7 -24,8
44,8
27,3
134,6 38,4
-6,8
76,3
18,2
-30
82,7 120,1 -37,1
36,2
18,7
120,1 42,3
-21,2
80,2
22,1
-45
70,5 111,5 -49,4
27,6
10,1
105,6 46,2
-35,7
84,1
26,0
-60
58,2 102,9 -61,7
19,0
1,5
91,1
-50,2
88,0
29,9
166,1 -14,8
B’
C
39,4
33,4
A
A’
B
A
B
60˚
-15
-30
-45
58,3
B
B’
B
C
0
A’
B’
B
B’
B’
A
0
A
A
B
A
C
A
35˚
50,1
-15˚
mm
-60
mm
Fr
15
DMH-WT7600NEX/DMH-WT76NEX
Angle 60˚
Angle 35˚
Angle -15˚
A’
B
A’
A
C
C
A
C
A
A
B’
B
C
B
B’
C
94,6 128,4 -12,5
53,4
35,9
134,1 38,6
7,7
72,4
14,3
-15
82,3 119,8 -24,8
44,8
27,3
119,6 42,5
-6,8
76,3
18,2
-30
70,1 111,2 -37,1
36,2
18,7
105,1 46,3
-21,2
80,2
22,1
-45
57,8 102,6 -49,4
27,6
10,1
90,6
50,2
-35,7
84,1
26,0
-60
45,5
94,0
19,0
1,5
76,1
54,1
-50,2
88,0
29,9
50,6
152,6 -14,8
B’
C
39,4
33,4
A
A’
B
A
B’
A’
0
B
B
B’
A
A’
B’
B
A
0
B
60˚
-15
-30
-61,7
-45
25˚
-15˚
mm
-60
mm
16 Fr
DMH-WT8600NEX/DMH-WT86NEX
DMH-WT7600NEX/DMH-WT76NEX
Angle 60˚
Angle 25˚
Angle -15˚
Angle 60˚
Angle 25˚
A’
A’
A’
C
C
C
A
A
A
A
A
A’
B
A
A’
C
13,4 122,7 100,3
-9,9
38,5
-15
109,1 94,0
-23,5
-30
95,5
87,7
-45
81,9
-60
68,3
A
A’
B
B’
C
16,7
149,0 14,6
7,7
52,4
-5,7
32,2
10,4
134,6 18,4
-6,8
56,3
-1,8
-37,1
25,8
4,1
120,1 22,3
-21,2
60,2
2,1
81,3
-50,7
19,5
-2,3
105,6 26,2
-35,7
64,1
6,0
75,0
-64,3
13,2
-8,6
91,1
-50,2
68,0
9,9
30,1
B’
B
B’
B
B’
19,4
C
B’
B
146,1 -14,8
B’
B
0
A
A’
50,6
132,6 -14,8
B
B’
B
A
B’
B
B’
C
A’
B
B’
C
A
19,4
13,4 108,6 93,8
-9,9
38,5
16,7
A’
B
B’
C
134,1 18,6
7,7
52,4
-5,7
-15
95,0
87,5
-23,5
32,2
10,4
119,6 22,5
-6,8
56,3
-1,8
-30
81,4
81,1
-37,1
25,8
4,1
105,1 26,3
-21,2
60,2
2,1
-45
67,8
74,8
-50,7
19,5
-2,3
90,6
30,2
-35,7
64,1
6,0
-60
54,2
68,4
-64,3
13,2
-8,6
76,1
34,1
-50,2
68,0
9,9
B’
B
58,3
C
C
C
A
0
A’
A’
A’
A
Angle -15˚
mm
mm
REMARQUES
Fr
17
2 Es
Panel trasero
(terminales
principales)
▶DMH-WT8600NEX/DMHWT7600NEX/DMH-WT86NEX/DMHWT76NEX/DMH-WC6600NEX/DMHWC5700NEX
Cable de tierra
AMPLIFICADOR DE
POTENCIA
▶DMH-W4660NEX/DMH-W4600NEX
Es
3
4 Es
NOTA
NOTAS
Es
5
iPhone y teléfono
inteligente
NOTAS
Teléfono inteligente
(dispositivo Android™)
iPhone
6 Es
SUGERENCIAS
NOTAS
NOTAS
Cámara
Es
7
Cable Micro HDMI a HDMI (se vende por
separado)
Dispositivo HDMI (se vende por
separado)
NOTA
Pantalla trasera
8 Es
5 cm
No cubra esta área
5 cm
Es
9
3
2
4
SUGERENCIA
10 Es
5
1
▶DMH-WC6600NEX/DMH-WC5700NEX
2
SUGERENCIA
▶DMH-W4600NEX/DMH-W4600NEX
1
Es
11
12 Es
1
2
2
NOTA
1
Es
13
DMH-WT7600NEX/DMH-WT76NEX
Centro
Frontal
75
38,1
115,4
128,2
115,4
128,2
mm
Izquierd
158,2
98,2
145,4
85,4
mm
55
Derecha
Derecha
18,1
98,2
158,2
mm
mm
14 Es
mm
mm
Trasera
85,4
145,4
mm
60˚
15˚
A
15
30
60
mm
NOTA
A
0
B
60˚
-15
-30
-45
35˚
-15˚
-60
mm
Es
15
DMH-WT7600NEX/DMH-WT76NEX
DMH-WT8600NEX/DMH-WT86NEX
Ángulo 60˚
Ángulo 35˚
Ángulo -15˚
Ángulo 60˚
A’
C
C
C
A
C
C
A
C
A
A
A
A
B’
B
B’
B
B
C
A’
B
B’
C
107,3 137,3 -12,5
53,4
35,9
149,0 34,6
7,7
72,4
14,3
-15
95,0 128,7 -24,8
44,8
27,3
134,6 38,4
-6,8
76,3
18,2
-30
82,7 120,1 -37,1
36,2
18,7
120,1 42,3
-21,2
80,2
22,1
-45
70,5 111,5 -49,4
27,6
10,1
105,6 46,2
-35,7
84,1
26,0
-60
58,2 102,9 -61,7
19,0
1,5
91,1
-50,2
88,0
29,9
166,1 -14,8
B’
C
39,4
33,4
A
A’
B
A
B
B’
C
94,6 128,4 -12,5
53,4
35,9
134,1 38,6
7,7
72,4
14,3
-15
82,3 119,8 -24,8
44,8
27,3
119,6 42,5
-6,8
76,3
18,2
-30
70,1 111,2 -37,1
36,2
18,7
105,1 46,3
-21,2
80,2
22,1
-45
57,8 102,6 -49,4
27,6
10,1
90,6
50,2
-35,7
84,1
26,0
50,1
-60
45,5
94,0
19,0
1,5
76,1
54,1
-50,2
88,0
29,9
152,6 -14,8
B’
C
39,4
33,4
A
A’
B
-61,7
A
B’
A’
50,6
B
B
C
0
A’
B’
B
B’
A
A’
B’
B
B’
B
B’
58,3
A’
A’
A’
0
Ángulo -15˚
A’
A’
A
Ángulo 35˚
mm
mm
16 Es
DMH-WT8600NEX/DMH-WT86NEX
Ángulo 60˚
Ángulo 25˚
B
Ángulo -15˚
A’
A
A’
A’
C
C
C
A
A
A
B’
B
13,4 122,7 100,3
-9,9
38,5
A
0
-15
109,1 94,0
-23,5
-30
95,5
87,7
-45
81,9
-60
68,3
19,4
A
A’
A
A’
B
B’
C
16,7
149,0 14,6
7,7
52,4
-5,7
32,2
10,4
134,6 18,4
-6,8
56,3
-1,8
-37,1
25,8
4,1
120,1 22,3
-21,2
60,2
2,1
81,3
-50,7
19,5
-2,3
105,6 26,2
-35,7
64,1
6,0
75,0
-64,3
13,2
-8,6
91,1
-50,2
68,0
9,9
B
60˚
-15
-30
-45
146,1 -14,8
C
C
58,3
B’
B’
B
B’
0
B
B’
B
A
A’
B
25˚
-15˚
-60
30,1
mm
mm
Es
17
DMH-WT7600NEX/DMH-WT76NEX
Ángulo 60˚
Ángulo 25˚
Ángulo -15˚
A’
A’
A’
C
C
C
A
A
A
B’
B
0
A
A’
50,6
132,6 -14,8
B
B’
B
A
B’
B
B’
C
A’
B
B’
C
A
19,4
13,4 108,6 93,8
-9,9
38,5
16,7
A’
B
B’
C
134,1 18,6
7,7
52,4
-5,7
-15
95,0
87,5
-23,5
32,2
10,4
119,6 22,5
-6,8
56,3
-1,8
-30
81,4
81,1
-37,1
25,8
4,1
105,1 26,3
-21,2
60,2
2,1
-45
67,8
74,8
-50,7
19,5
-2,3
90,6
30,2
-35,7
64,1
6,0
-60
54,2
68,4
-64,3
13,2
-8,6
76,1
34,1
-50,2
68,0
9,9
mm
NOTAS
18 Es
19
Es
© 2020 PIONEER CORPORATION
<CRD5214-B> UC