Siemens DH 21100, DH 24100, DH 18100 Инструкция по эксплуатации

Operating and installation instructions
Instrukcja u˝ytkowania i monta˝u
Instrukciä po montaøu i qkspluatacii
DH 18100
DH 21100
DH 24100
automatic
e
Siemens-Electrogeräte GmbH
E-Nr. .................... FD ...................
400V3
kW
10 bar
Cu
Typ DHT
GB
RU
PL
DH 18100:
46
Before you use the appliance, please
read these operating instructions
carefully!
Safety information
■ This appliance should be installed and
commissioned by a qualified expert who
must observe the enclosed installation
instructions.
■ The instantaneous water heater must be
installed in a room that is not exposed to
freezing temperatures.
■ The mixer tap and hot water pipe can
become very hot.
Make sure that children are aware of this
hazard.
Your new appliance
The water is heated continuously while it is
flowing through the instantaneous water
heater. Electricity is only consumed while
water is flowing.
This appliance can supply hot water to taps
in several different locations. It should
however be installed close to the tap that is
used the most frequently. This will enable
you to reduce energy consumption.
■ Montaø nagrevatelä i vvod ego v
qkspluataciü v sootvetstvii s
instrukciej doløen provoditæ
specialist.
■ Protohnyj nagrevatelæ doløen bytæ
ustanovlen v otaplivaemom pomewenii.
■ Smesitelæ i truba s teploj vodoj mogut
silæno nagrevatæsä. Obäzatelæno
predupredite ob qtom detej.
How to operate the heater
Kak obsluøivatæ nagrevatelæ
Your instantaneous water heater has two
power settings:
e economy – two-thirds power
II maximum heating – full power
automatic
e
>e< setting
Stopieƒ e
is ideal for
podxodit idealæno dlä nagreva vody dlä
wash-basins
umywalka
umyvalænika,
showers
duπa,
bidets
bidet
bidq.
>II< setting
Silænyj nagrev II
should be used where a higher temperature
or a larger volume of water is required, e.g.
ispolæzujte dlä nagreva vody do vysokoj
temperatury ili dlä nagreva bolæπogo
kolihestva vody, naprimer, dlä
kitchen sinks
mojki posudy,
cleaning
vlaønoj uborki,
bath-tubs
prinätiä vanny.
If you are using a thermostat-controlled
mixer tap, set the heater to >II<.
Esli Vy polæzuetesæ batareej s
termostatom, to ustanavlivajte
regulätor temperatury na II.
1. Set the heater to either >e< or >II<, as
1. Ustanovite regulätor temperatury na
nagrev “e“ ili “II“.
2. Otkrojte kran gorähej vody.
required.
2. Turn on the hot-water tap.
The instantaneous water heater switches
on automatically and heats the water as it
flows through the appliance. The heater
switches off again when you turn off the
tap.
Tip for saving energy: Use the >e< setting
as often as possible.
2
Increasing the water
temperature:
Povyπenie temperatury
nagreva vody
When the tap is turned on fully, it is
possible that the heater capacity is not
sufficient to heat the water to the required
temperature.
Pri polnostæü otkrytom krane gorähej
vody v nekotoryx sluhaäx mownosti
nagrevatelä ne xvataet dlä togo, htoby
nagretæ vodu do øelaemoj temperatury.
Turn the tap off slightly. The water flows
through the appliance more slowly and
reaches a higher temperature as a result.
Nemnogo prikrutite kran. Voda budet
medlennee tehæ po nagrevatelü i
temperatura ee povysitsä.
Reducing the water
temperature:
Poniøenie temperatury
nagreva vody
Mix with cold water.
Podmeπajte xolodnoj vody.
Conserving energy
Qkonomiä qlektroqnergii
Please use economy setting "e" as often as
possible.
Polæzujtesæ kak moøno hawe stupenæü
e".
nagreva "e
To minimise energy consumption when
turning off the hot water:
Qlektroqnergiä budet rasxodovatæsä
osobenno qkonomno, esli Vy po
okonhanii otbora vody budete
obrawatæ vnimanie na sleduüwee:
Turn off the hot-water tap slowly in order to
use the residual heat of the instantaneous
water heater.
This also prevents the water temperature
from briefly increasing above the
preselected temperature if the hot-water
tap is turned on again within the next few
minutes.
To obtain particularly uniform hot-water
temperatures, it is recommended to use
thermostat-controlled mixer taps.
The thermostat-controlled mixer tap must
be suitable for hydraulically controlled
instantaneous water heaters.
V rezulætate medlennogo zakryvaniä
vodoprovodnogo krana optimalæno
ispolæzuetsä ostatohnoe teplo
protohnogo nagrevatelä.
Pri qtom Vam takøe udastsä izbeøatæ
togo, hto pri povtornom otbore gorähej
vody v tehenie sleduüwix neskolækix
minut temperatura vody budet
nekotoroe vremä vyπe zadannoj.
Ispolæzovanie smesitelä s
termostatom daet to preimuwestvo, hto
v rezulætate dostigaetsä osobenno
ravnomernaä temperatura gorähej vody.
Smesitelæ s termostatom doløen bytæ
rasshitan na ispolæzovanie ego v
komplekte s protohnym nagrevatelem s
gidravliheskoj sistemoj upravleniä.
Note about operation
When a hot-water tap is turned on by only
a small amount, the instantaneous water
heater operates at half power regardless of
which setting (e, II) has been selected.
When a hot-water tap is turned on fully, the
appliance operates at the maximum level of
power that corresponds to whichever
setting has been selected.
How to clean the heater:
Kak uxaøivatæ za
nagrevatelem
Wipe the heater off with a damp cloth only.
Nagrevatelæ nuøno liπæ protiratæ
vlaønoj träpkoj.
Pri qtom ne sleduet primenätæ ostrye
predmety ili abrazivnye histäwie
sredstva.
Do not use any sharp objects or abrasive
detergents.
3
What to do if a problem
occurs:
Neispravnostæ. Hto
delatæ?
When a problem occurs, the cause is quite
often something simple. Please check
whether you can resolve the problem yourself with the aid of the following
information. In so doing you will avoid the
costs of an unnecessary call by a service
engineer.
Neispravnosti hasto voznikaüt iz-za
melohej. Poøalujsta, poprobujte
samostoätelæno ustranitæ neispravnostæ,
rukovodstvuäsæ privedennymi niøe
ukazaniämi. V rezulætate Vy ne budete
oplahivatæ nenuønyj vyzov sluøby
servisa.
Voda ne nagrevaetsä ili ee vytekaet
sliπkom malo:
■ proveræte predoxraniteli na
raspredelitelænom wite,
■ vozmoøno padenie napora v
vodoprovodnoj seti: pri sliπkom nizkom
davlenii v seti nagrevatelæ ne
vklühaetsä,
■ filætr v krane ili duπevoj golovke
zabit nakipæü: filætr neobxodimo
vykrutitæ i prohistitæ,
■ uglovoj regulirovohnyj klapan zabit:
polnostæü otkrojte kran gorähej vody i
neskolæko raz otkrutite i zakrutite
klapan, posle qtogo prohistite filætr v
krane,
■ nagrevatelæ neobxodimo ohistitæ ot
nakipi: dlä qtogo sleduet vyzvatæ
specialista.
Nagrevatelæ vyklühaetsä vo vremä
otbora gorähej vody, temperatura vody
poniøaetsä:
■ v krane gorähej vody sleduet zamenitæ
staruü prokladku na novuü, kotoraä ne
razbuxaet ot vody.
Esli Vam vse-taki ne udalosæ samostoätelæno ustranitæ neispravnostæ, to
pervym delom vyklühite predoxranitelæ
na raspredelitelænom wite, a zatem
vyzyvajte specialista po remontu.
The water does not heat up or not
enough water flows out of the tap:
■
Check the fuse in the domestic wiring.
■ Drop in pressure in the water mains.
If the pressure is too low, the appliance will
not switch on.
■ The strainer on the tap or shower head is
blocked. Unscrew the strainer and either
clean or descale it.
■ The angle-body control valve is blocked.
Turn the hot-water tap on fully and open
and close the control valve several times.
After this has been done, clean the strainer
on the tap.
■ The heater needs descaling. Arrange for
a service engineer to visit.
The heater switches off while water is
flowing and then the temperature of the
water drops:
■
The washer inside the hot-water tap must
be a non-swelling type. If you cannot
resolve the problem yourself, switch off the
heater via the fuse in the domestic wiring.
Arrange for a service engineer to visit.
Important!
Vnimanie!
Repairs to this appliance should only be
carried out by a qualified expert. You
could be exposed to considerable
danger if the heater is not repaired
properly.
Remont doløen provoditæsä tolæko
specialistom. Vy podvergnete sebä
bolæπoj opasnosti, esli doverite
provedenie remonta nekompetentnomu
licu.
Customer Service
Serwis
Sluøba servisa
When you call our Customer Service department, you will be asked to quote your
appliance's product number (E) and serial
number (FD). These numbers can be found
on the underside of the instantaneous
water heater.
Esli Vy obrawaetesæ v sluøbu servisa, to
nazyvajte, poøalujsta, E-nomer i FDnomer Vaπego nagrevatelä. Qti nomera
Vy najdete na dniwe protohnogo
nagrevatelä.
4
Installation instructions
for qualified persons
Rukovodstvo po montaøu
dlä specialista
Please observe the
following:
Na hto obratitæ vnimanie
■ You must comply with all legal requirements that apply in the country where the
appliance is to be installed as well as any
regulations prescribed by the local
electricity and water supply companies.
■ Sleduet strogo soblüdatæ predpisaniä,
ustanovlennye zakonom dannoj strany,
mestnymi predpriätiämi po qnergo- i
vodosnabøeniü.
■ Connect the heater to the water supply
before you wire it up to the mains electricity.
■ The heater must be installed in a room
that is not exposed to freezing
temperatures. It should be installed close
to the tap that is used the most frequently.
■
Connect the appliance only to the cold
water. A non-return valve must NOT be
connected to the cold water.
■
Do not use plastic pipes. Steel or copper
pipes are suitable for the cold-water
supply. Insulated copper pipes are
particularly suitable for the hot-water pipes.
■ Nagrevatelæ moøno raspolagatæ tolæko
v otaplivaemom pomewenii. On doløen
bytæ smontirovan poblizosti ot tex tohek
otbora gorähej vody, kotorymi naibolee
hasto polæzuütsä.
■ Nagrevatelæ moøno podklühatæ tolæko
k vodoprovodu xolodnoj vody. V dannom
sluhae ustrojstvo dlä predotvraweniä
obratnogo potoka v vodoprovod vstraivatæ
nelæzä.
Important!
It must not be possible to touch any live
components after installation has been
completed.
■
Perform a function test and check
whether Heat Setting II switches on at a
low water-pipe pressure. See Page 11.
Explain the appliance to the user and
please give him the operating instructions.
List of items supplied
■
1
Montageschablone
Montaønyj πablon
Mounting template
Montagesjabloon
Gabarit de montage
˙
Szablon montazowy
■ Podklühenie vody sleduet provoditæ
pered qlektropodklüheniem.
■ Nikogda nelæzä ispolæzovatæ truby iz
sintetiki. Luhπe vsego, esli truboprovod
dlä podvoda xolodnoj vody vypolnen iz
stalænyx ili mednyx trub. Dlä truboprovoda s gorähej vodoj osobenno podxodät
mednye truby s teploizoläciej.
2
3
12
7
14
14a
4
5
14a
10
14a
automatic
6
e
9
3
11
13
1
2
3
4
5
6
7
8
9
10
11
Instantaneous water heater
Installation template
Connection piece for hot water
Washer, red ø 15 mm
Connection piece for cold water
Washer, ø 24 mm
Mounting bolt
Wall plug
Securing nut
Threaded bushing
Cable grommet
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
7
8
9
10
Protohnyj nagrevatelæ
Montaønyj πablon
Patrubok dlä sliva gorähej vody
Uplotnenie, krasnogo cveta, 15 mm
Patrubok dlä podvoda xolodnoj vody
Uplotnenie, 24 mm
Montaønyj vint
Dübelæ
Krepeønaä gajka
Rezæbovaä vtulka
11 Nasadka dlä qlektrokabelä
5
Wall mounting
Monta˝ na Êcianie
Nastennyj montaø
There are two ways in which the
instantaneous water heater can be
mounted on the wall:
Protohnyj nagrevatelæ moøno
smontirovatæ na stene dvumä sposobami:
1. s pomowæü montaønogo vinta.
Nerovnosti steny (do 25 mm) moøno
skompensirovatæ;
1. Using the mounting bolt.
Unevenness in the wall up to a depth of
25 mm can be compensated for.
2. Making use of the holes that were
drilled for the old heater.
Use the mounting template to establish
whether the existing holes line up
properly.
The following describes the installation
procedure using the mounting bolt.
1. Marking the point for
mounting the heater and
selecting the opening for
the connecting cable.
Important!
V dalænejπem budet opisan tolæko
sposob krepleniä nagrevatelä s
pomowæü montaønogo vinta.
1. Oboznahæte tohku
Make sure that the connecting cable is
isolated from the mains electricity
supply!
2. ispolæzuä uøe imeüwiesä otverstiä,
ostavπiesä ot starogo nagrevatelä.
Proveræte, prikladyvaä montaønyj
πablon, podxodät li starye
otverstiä.
Vnimanie!
Mon
krepleniä i vyberite
otverstie dlä vvedeniä
setevogo kabelä.
Snahala ubeditesæ, hto kabelæ dlä
qlektropodklüheniä ne naxoditsä pod
napräøeniem!
tage
12
sch
ablo
ne M
oun
ti
Mon ng tem
plate
tage
G
sjab
loon abarit
de m
Sza
on
blon
mon tage
tazo
˙ wy
12
12
14
14a
14a
14a
3
1. Place hole 3 in the mounting template
over the cold-water inlet.
2. Select the most suitable hole through
which the connecting cable is be fed. The
connecting cable must pass through one of
the six holes marked 14 or 14a. Terminal
BZ 45Z20 can be used if the cable is fed
into the water heater through one of the
bottom holes marked 14a.
3. Mark the point (12) at which the
mounting bolt is to be inserted.
1. Otverstie 3 v montaønom πablone
sovmestite s otverstiem truby dlä
podvoda xolodnoj vody.
2. Vyberite naibolee podxodäwee
otverstie dlä setevogo kabelä. Kabelæ
dlä qlektropodklüheniä moøno
vvoditæ tolæko v odno iz πesti
otverstij 14 ili 14a. Esli kabelæ
budet vvoditæsä v nagrevatelæ herez
odno iz niønix otverstij 14a, to dlä
ego podklüheniä moøno ispolæzovatæ
promeøutohnuü klemmu BZ 45Z20.
3. Oboznahæte tohku 12 dlä krepleniä
6
montaønogo vinta.
2. Fitting the mounting bolt
and attaching the pipe
connecting pieces.
3. Open up the heater.
3. Otkrojte nagrevatelæ.
1.
2.
7
4. Punching out the holes
at the rear of the heater for
the mounting bolt and the
connecting cable.
Important!
When mounting the appliance, only the
holes actually required should be
punched out.
Any other holes that are not going to be
used must be sealed watertight.
nagrevatelä vylomajte
otverstiä dlä montaønogo
vinta i setevogo kabelä.
Vnimanie!
Dlä krepleniä nagrevatelä na stene
sleduet ispolæzovatæ tolæko
predusmotrennye dlä qtogo otverstiä na
ego zadnej stenke, kotorye Vy doløny
samostoätelæno vylomatæ.
Vylomannye, no neispolæzuemye
otverstiä Vy doløny germetihno
zadelatæ.
5. Inserting the connecting 5. Wprowadziç przewód
cable.
1. Push the grommet (11) over the end of
the connecting cable.
Note: Do not use the grommet for a cable
with a cross-section of 16 mm2. Without a
cable grommet the degree of protection is
splashproof only (IP 24).
4. V zadnej stenke
9
8
8
9
11
11
2. Place the heater over the connecting
2. Prisoedinite setevoj kabelæ k klemme
cable.
nagrevatelä.
3. Press the grommet into the hole in the
3. Tulejk´ ochronnà wcisnàç w tylnà Êciank´
3. Nasadku vdavite v zadnüü stenku
rear wall of the heater through which the
cable should be fed. Ensure that the edges
of the grommet are flush with the hole all
the way round.
4. Fit the heater onto the threaded bushing
(8) and secure it in place with the nut (9).
8
4. Nagrevatelæ navesæte na vtulku s
rezæboj 8 i zafiksirujte gajkoj 9.
6. Compensating for
unevenness in the wall.
6. Kompensaciä
nerovnostej steny
0–25mm
7. Water connection
7. Podklühenie vody
± 10
15
90 -120 mm
■
The water connection can be adjusted
vertically by slackening the locking screw 15.
■
Adapt the bend in the "hot" pipe so that
it lines up with the hot-water outlet. In so
doing, make sure that the "cold" elbow
connection is not bent.
Important!
Ensure that a distance of at least 6 mm is
maintained to live parts of the heater.
Connect the water outlet and inlet and
tighten the securing nut on the mounting
bolt.
■
■
■
■
S pomowæü ustanovohnogo vinta 15
qlement dlä podklüheniä vody moøno
otregulirovatæ po vysote na 10 mm.
Koleno truby "ggorähaä voda" moøno
nemnogo izognutæ dlä sovmeweniä s
otverstiem dlä podahi gorähej vody. Pri
qtom ugolkovyj qlement podklüheniä
"xolodnaä voda" izgibatæ nelæzä.
Vnimanie!
Sledite za tem, htoby rasstoänie meødu
tokoveduwimi qlementami i truboprovodami sostavlälo ne menee 6 mm.
Soedinite vse qlementy podklüheniä i
prohno zatänite krepeønuü gajku na
montaønom vinte.
9
8. Checking for leaks and
8. Nagrevatelæ proveræte
flushing the heater.
■
■
■
■
■
na germetihnostæ i
promojte ego.
■
Turn on the hot-water tap.
Check that all pipe joints are properly
sealed.
9. Electrical connection
■ As a matter of principle, the water
connections must be completed first of all
before the heater is connected to the
electricity supply. The appliance should be
wired up according to the circuit diagram
on the inside of the cover.
■
■
Zasilanie ∆ 400V 3 ~
Connection 400V AC, 3-phase
Otkrojte kran gorähej vody.
Proveræte vse soedineniä trub na
germetihnostæ.
■ Qlektropodklühenie moøno
provoditæ tolæko posle togo, kak byla
podklühena voda. Qlektropodklühenie
provoditsä v sootvetstvii s
qlektrosxemoj, izobraøennoj na
vnutrennej storone zawitnogo koøuxa.
■
Important!
Uwaga!
■
In order to comply with relevant safety
regulations, an all-pole disconnector must
be fitted in the domestic wiring. The gap
between contacts must be at least 3 mm.
■ Terminal BZ 45Z20 can be used if the
connecting cable is fed into the heater via
one of the bottom holes 14a.
■
The wires must not interfere with the
operation of release button A on the safety
temperature limiter.
Podklühaemoe napräøenie 400 V 3 ~.
Vnimanie!
■
18 kW
21 kW / 24 kW
L1
3
L1 L2
L3
L3
L2
5
1
A
14a
A
10
14a
10. Mounting the cover
onto the heater
When you mount the cover onto the
heater, ensure that the switch knob and
the switch spindle are correctly aligned.
10. Zakryvanie
nagrevatelä
e
Pri zakryvanii kryπki nagrevatelä
sledite za pravilænym poloøeniem
naruønoj ruhki i osi pereklühatelä
vnutri nagrevatelä.
e
autom
atic
e
11. Initial start-up
1. Switch on via the water heater fuses in
1. Vklühite na raspredelitelænom
the domestic wiring.
wite predoxraniteli dlä nagrevatelä.
2. Select Setting II on the appliance and
check the water temperature.
At a low water-pipe pressure:
Turn on additional cold-water taps and
check whether the heater switches on. If
this does not occur, the flow control
regulator will have to be removed.
See Page 12.
2. Ustanovite regulätor na stupenæ
nagreva II i prokontrolirujte
temperaturu nagretoj vody.
Pri nizkom davlenii vody v
vodoprovode:
Otkrojte drugie krany xolodnoj vody i
proveræte, ne vklühilsä li nagrev.
Esli net, to protohnyj nagrevatelæ
pridetsä demontirovatæ (opisanie
smotrite na stranice 12).
11
Removing the water flow
limiter.
Demontaø ogranihitelä
potoka
If the pressure in the water mains is too
low, the water flow limiter can be removed.
Pri nizkom napore vody v vodoprovodnoj
seti moøno udalitæ ogranihitelæ
obratnogo potoka.
Important!
Shut off the water supply!
Vnimanie!
Snahala perekrojte vodu!
1.
2.
4.
3.
Priority switch for
combination with electric
storage heaters.
Sxema prioritetnogo
podklüheniä dlä kombi nacii s qlektronagre vatelænymi priborami
If the heater is going to be operated in this
way, a priority switch must be connected
into the line connecting the L2 phase to the
appliance. It should be mounted on the
meter or distribution panel.
Pri dannom reøime raboty k faznomu
provodu nagrevatelä L2 (L2)sleduet
podklühitæ prioritetnyj vyklühatelæ.
On montiruetsä na paneli shethika ili
raspredelitelä.
L1
L2
L3
f3
a
b
nur bei 21 kW- und
24 kW-Gerät
L1
L2
L3
PE
l1
3 2
1
ϑ
f1
4
5
a,b Control line for the electricity supply
company connected to the coil input
on the charging contactor
f1
Safety temperature limiter with mains
terminals
f3
Priority switch (current relay)
l1
Mains terminal (only on 21 kW and
24 kW appliances)
12
6
a,b kabelæ qlektropitaniä, iduwij k
f1
f3
l1
vxodu katuπki zarädnogo
kontaktora
predoxranitelænoe teplovoe rele
s klemmami dlä podklüheniä
setevogo kabelä
prioritetnyj vyklühatelæ
(tokovoe rele)
klemma dlä podklüheniä setevogo
kabelä (tolæko dlä nagrevatelej
mownostæü 21 kVt i 24 kVt)
Technical specifications
Rated power (kW)
18
21
24
Texniheskie dannye
18
21
24
Nominalænaä
mownostæ (kVt)
18
21
24
1-ä stupenæ
6
7
8
2-ä stupenæ
12
14
16
Heating capacity (kW)
Economy setting e
Stage 1
6
7
8
1.stopieƒ
6
7
8
Stage 2
12
14
16
2.stopieƒ
12
14
16
Maximum heating II
Mownostæ nagreva (kVt)
Qkonomihnyj reøim e
Stage 1
9
10,5
12
1.stopieƒ
9
10,5
12
Silænyj nagrev II
Stage 2
18
21
24
18
21
24
1-ä stupenæ
9
10,5
12
2-ä stupenæ
18
21
24
Switching point (l/min.)
Stage 1
4,0
4,5
5,0
4,0
4,5
5,0
Tohka vklüheniä (l/min.)
Stage 2
5,0
5,8
6,6
2.stopieƒ
5,0
5,8
6,6
1-ä stupenæ
4,0
4,5
5,0
2-ä stupenæ
5,0
5,8
6,6
Mixed water (l/min.)
at rated power
Smeπannaä voda (l/min.)
at approx. 38ºC
9,8
11,5 13,1
dla oko∏o 38 °C
9,8
11,5 13,1
nahinaä s T ok. 38°S
9,8
11,5 13,1
at approx. 50ºC
6,7
7,8
dla oko∏o 50 °C
6,7
7,8
nahinaä s T ok. 50°S
6,7
7,8
9,0
9,0
(Inlet water temperature 12ºC)
(temperatura pritohnoj vody 12°S)
Minimum flow pressure
at appliance* (bar)
Min. napor potoka vody
na vyxode iz nagrevatelä* (bar)
with
water flow limiter
without
water flow limiter
0,6
0,4
0,8
0,5
* To this must be added the drop of
pressure at the mixer tap
0,9
0,6
0,6
0,8
0,4
0,5
9,0
0,9
0,6
0,8
0,9
0,6
0,4
0,5
0,6
* S uhetom padeniä davleniä v
smesitele
236
136
56
472
388
83
Dimensions
Wymiary
Gabarity
42
G12 A
100
33
57
13
Special accessories
Pipe adapter kit BZ 45U20:
To enable an instantaneous water heater to
be mounted under a sink.
Nabor komplektuüwix qlementov
BZ 45U20: dlä montaøa protohnogo
nagrevatelä pod rakovinoj.
Intermediate terminal block BZ 45Z20:
Required when the mains connecting cable
is fed in through the bottom access hole 14a.
Promeøutohnaä klemma BZ 45Z20:
ispolæzuetsä v sluhae, esli pitaüwij
kabelæ vvoditsä herez niønee
otverstie 14a.
Truncated connecting piece sealed at rear
for water connection from below (e.g. cold
water connection via fitting mounted below
heater):
Elbow joint, „cold“ (right)
Order no.
056169
Ukorohennyj i zakrytyj pozadi
patrubok dlä podklüheniä vody snizu
(naprimer, dlä podklüheniä xolodnoj
vody herez aramaturu, vstroennuü po
metodu utoplennogo montaøa):
056169
Elbow joint, „hot“, (left)
Order no.
255568
koleno "xolodnaä voda" (sprava)
nomer dlä zakaza
056169
255568
Disposal
This appliance is labelled in accordance
with European Directive 2002/96/EG
concerning used electrical and electronic
appliances (waste electrical and electronic
equipment – WEEE). The guideline
determines the framework for the return
and recycling of used appliances as
applicable throughout the EU.
255568
Утилизация отходов
Данный прибор имеет отметку о
соответствии европейским нормам
2002/96/EG утилизации электрических и
электронных приборов (waste electrical
and electronic equipment – WEEE).
Данные нормы определяют
действующие на территории Евросоюза
правила возврата и утилизации старых
приборов.
46
15
Family Line
01805-2223
Siemens-Hausgeräte
Besuchen Sie uns im Internet:
http://www.siemens.de/hausgeraete
Siemens-Electrogeräte GmbH
Carl-Wery-Str. 34/81739 München//Germany
800 198 00
Printed in Germany 10/05 GB, PL, RU">