Team Associated Reflex 14B Buggy Kit Instruction manual

Team Associated Reflex 14B Buggy Kit is a high-performance buggy designed for racing enthusiasts. This kit comes with all the necessary parts to build a functional buggy and includes a comprehensive instruction manual with detailed steps and helpful tips. Prepare for off-road action with the Reflex 14B!

PDF

Document

2
:: Introduction:: Introduction
:: RC14B Kit Features:: RC14B Kit Features
:: Additional:: Additional
:: Other Helpful Items:: Other Helpful Items
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations.
New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before
you start to build.
• New RC8B4e Gamma-style molded body, clear
• Three sealed differentials
• Factory Team Threaded coil-over shock absorbers
• Factory Team 12mm Wheel Hexes
• Adjustable turnbuckles
• Adjustable inserts for caster blocks and rear hubs
• Aluminum steering rack
• Front universal driveshafts
• Updated molded tub chassis with hook and loop strap for battery installation and covered center driveshaft
• Aluminum center driveshaft
• Off road 12mm hex drive white wheels with high-grip racing tires
Your new Reflex 14B comes as a kit. The following items are needed for completion
• Polycarbonate Paint • 6-cell NiMh or 2 LiPo battery • Suitable battery charger • (4) AA batteries
• ESC • Transmitter / Receiver • Steering Servo • Motor
Tools included: • Multi-wrench
• Silicone Shock Fluid (Refer to catalog for complete listings) • Silicone Diff Fluid (Refer to catalog for complete listings)
• Body Scissors (AE Part # 1737) • Reamer / Hole Punch (#1499) • Shock Pliers (#1675) • Wire Cutters
• FT Hex/Nut Wrenches (AE Part # 1519)• Needle Nose Pliers • Hobby Knife • Soldering Iron
• Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
• FT Dual Turnbuckle Wrench (#1114) • FT Universal Tire Balancer (#1498)
:: Table of Contents:: Table of Contents
1................... Cover
2................... Introduction
3...................1:1 Hardware “Fold Out”
4 - 15...........Steps 1- 36
16 - 17.........Notes
18................ Back Cover
:: Notes:: Notes
This symbol indicates a special note or instruction in the manual.
!
There is a 1:1 hardware foldout page in the front of the manual. To check
the size of a part, line up your hardware with the correct drawing until you
find the exact size. Each part in the foldout has a number assigned to it
for ordering replacement parts.
Associated Electrics, Inc.
21062 Bake Parkway.
Lake Forest, CA 92630
http://www.Associated Electrics.com · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501

3
:: Hardware - 1:1 Scale View:: Hardware - 1:1 Scale View
3x2.5mm (31500)
3x3mm (25225)
3x8mm (4670)
Set Screws
Notes:
M2.5 Locknut (89215, 21546)
M4 Locknuts:
Serrated Steel (Silver)(91826)
Flanged (Black) (91148)
FT Aluminum (Blue) (31551)
Serrated Aluminum (Black) (91738)
Nuts (lock/plain)
Flat Head (fhcs)
2.5x10mm (31350)
2.5x6mm (31520)
Button Head (bhcs)
2.6x6mm (21546)
2.6x8mm (21546)
2.6x10mm (21546)
Button Head (bhst)
Ball Bearings
4x7x2.5mm (21512)
4x8x3mm (21512)
8x12x3.5mm (21512)
2.7x6.7x0.5mm (21546)
4x8x0.5mm (21516)
Shims and Washers
Flat Head (fhst)
2x8mm (21546)
2.6x8mm (21546)
2.6x10mm (21546)
Cap Head (shcs)
2.5x12mm (8691)

:::: Step 3Step 3
:::: Step 2Step 2
4
:::: Step 1Step 1
Build 2 (1 front, 1 rear)
- OR -
#6588
black grease
21529
Diff
case
21530
O-Ring
3.8 x 1mm
21530
O-Ring
3.8 x 1mm
21516
Washer
4x8x0.5mm
21516
Washer
4x8x0.5mm
21524
Diff
outdrive
21529
Diff
cap
21524
Diff
outdrive
x3x3
x3x3 x2x2
21529
Diff
planetary
gear
21546
M2x8mm
FHST
21512
8x12x3.5mm
bearing
21526
Diff ring
gear (37T)
21527
Diff ring
gear (37T)
21529
Diff
cross pin
21529
Diff sun
gear
21529
Diff sun
gear
21516
Pin
1.5 x 6mm
21516
Pin
1.5 x 6mm
#21526 comes with
two ring and pinions
#21527 comes with
two ring and pinions,
and two spur gears
(58T, 70T)
!

Hello! I am an AI chatbot specifically trained to assist you with the Team Associated Reflex 14B Buggy Kit Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Gamma-style molded body
Sealed differentials
Threaded coil-over shocks
Adjustable turnbuckles
Aluminum steering rack
Universal driveshafts
Molded tub chassis
Aluminum center driveshaft

Frequently asked questions

This kit includes the parts necessary to build a functional buggy, excluding the following: Polycarbonate paint, 6-cell NiMh or 2 LiPo battery, suitable battery charger, ESC, transmitter/receiver, steering servo, and motor. Refer to the instruction manual for the exact list of included parts.

You will need Polycarbonate paint, 6-cell NiMh or 2 LiPo battery, suitable battery charger, ESC, transmitter/receiver, steering servo, and motor. The instruction manual also lists other helpful items like silicone shock and diff fluid, body scissors, and tools.

To set the gear mesh, push the teeth of the motor mount cam (#21531) into the corresponding tooth pattern of the motor mount insert. The spur gear should rock back and forth without making the pinion gear move. Excessive movement can damage the gears.