NissanConnect® Owner’s Manual. Nissan Murano, 2019 Murano, 2019
Below you will find brief information for Murano. This owner's manual provides essential information for operating and maintaining your vehicle safely. It covers topics such as safety features, instruments and controls, pre-driving checks, monitor, climate, audio, phone systems, starting and driving procedures, emergency situations, vehicle appearance and care, do-it-yourself maintenance, technical information, schedules.
Advertisement
Advertisement
ANTENNA CAR PHONE OR CB RADIO
The vehicle is equipped with a shark fin antenna and an antenna pattern is printed inside the rear window.
CAUTION
∙ Do not place metalized film near the rear window glass or attach any metal parts to it. This may cause poor reception or noise.
∙ When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna.
Lightly wipe along the antenna with a dampened soft cloth.
When installing a CB, ham radio or car phone in your vehicle, be sure to observe the following precautions; otherwise, the new equipment may adversely affect the engine control system and other electronic parts.
WARNING
∙ A cellular phone should not be used for any purpose while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular phones while driving.
∙ If you must make a call while your vehicle is in motion, the hands free cellular phone operational mode is highly recommended. Exercise extreme caution at all times so full attention may be given to vehicle operation.
∙ If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle.
CAUTION
∙ Keep the antenna as far away as possible from the electronic control modules.
∙ Keep the antenna wire more than 8 in
(20 cm) away from the electronic control system harnesses. Do not route the antenna wire next to any harness.
∙ Adjust the antenna standing-wave ratio as recommended by the manufacturer.
∙ Connect the ground wire from the CB radio chassis to the body.
∙ For additional information, it is recommended that you visit a NISSAN dealer for servicing.
Monitor, climate, audio, phone and voice recognition systems
4-33
5 Starting and driving
Precautions when starting and driving . . . . . . . . . . 5-4
Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . 5-4
Three-way catalyst . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Tire Pressure Monitoring System
(TPMS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Avoiding collision and rollover . . . . . . . . . . . . . . . . 5-9
Off-road recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Rapid air pressure loss . . . . . . . . . . . . . . . . . . . . . . 5-10
Drinking alcohol/drugs and driving . . . . . . . . . . .5-11
Driving safety precautions . . . . . . . . . . . . . . . . . . . .5-11
Push-button ignition switch . . . . . . . . . . . . . . . . . . . . 5-13
Operating range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Push-button ignition switch positions . . . . . . . 5-14
Emergency engine shut off . . . . . . . . . . . . . . . . . . 5-15
NISSAN Vehicle Immobilizer System . . . . . . . . . 5-16
Before starting the engine . . . . . . . . . . . . . . . . . . . . . . 5-16
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Remote Engine Start (if so equipped) . . . . . . . . 5-18
Driving the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Continuously Variable Transmission
(CVT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Traffic Sign Recognition (TSR) (if so equipped) . . . 5-24
System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25
Turning the Traffic Sign Recognition
(TSR) system on and off . . . . . . . . . . . . . . . . . . . . . 5-26
System temporarily unavailable . . . . . . . . . . . . . 5-26
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-27
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
LDW system operation . . . . . . . . . . . . . . . . . . . . . . 5-28
How to enable/disable the LDW system . . . . . 5-29
LDW system limitations. . . . . . . . . . . . . . . . . . . . . . 5-30
System temporarily unavailable . . . . . . . . . . . . . 5-31
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-31
Intelligent Lane Intervention (I-LI)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
I-LI system operation . . . . . . . . . . . . . . . . . . . . . . . . 5-33
How to enable/disable the I-LI system. . . . . . . 5-34
I-LI system limitations . . . . . . . . . . . . . . . . . . . . . . . 5-35
System temporarily unavailable . . . . . . . . . . . . . 5-36
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-37
Blind Spot Warning (BSW) (if so equipped) . . . . . . . 5-38
BSW system operation . . . . . . . . . . . . . . . . . . . . . . 5-40
How to enable/disable the BSW system . . . . . 5-41
BSW system limitations. . . . . . . . . . . . . . . . . . . . . . 5-42
BSW driving situations . . . . . . . . . . . . . . . . . . . . . . . 5-43
System temporarily unavailable . . . . . . . . . . . . . 5-47
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-48
Rear Cross Traffic Alert (RCTA) (if so equipped) . . 5-49
RCTA system operation. . . . . . . . . . . . . . . . . . . . . . 5-50
RCTA system limitations . . . . . . . . . . . . . . . . . . . . . 5-53
System temporarily unavailable . . . . . . . . . . . . . 5-56
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-57
Cruise control (if so equipped) . . . . . . . . . . . . . . . . . . 5-58
Precautions on cruise control. . . . . . . . . . . . . . . . 5-58
Cruise control operations. . . . . . . . . . . . . . . . . . . . 5-59
Intelligent Cruise Control (ICC) (if so equipped) . . 5-61
How to select the cruise control mode . . . . . . 5-63
System temporarily unavailable . . . . . . . . . . . . . 5-77
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-79
Rear Automatic Braking (RAB) (if so equipped) . . 5-85
RAB system operation . . . . . . . . . . . . . . . . . . . . . . . 5-86
Turning the RAB system on/off . . . . . . . . . . . . . .5-88
RAB system limitations . . . . . . . . . . . . . . . . . . . . . .5-88
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 5-90
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-90
Automatic Emergency Braking (AEB)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-91
AEB system operation . . . . . . . . . . . . . . . . . . . . . . . 5-92
Turning the AEB system on/off . . . . . . . . . . . . . . 5-94
AEB system limitations . . . . . . . . . . . . . . . . . . . . . . 5-94
System temporarily unavailable . . . . . . . . . . . . . 5-96
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . . 5-96
System maintenance. . . . . . . . . . . . . . . . . . . . . . . . 5-97
Automatic Emergency Braking (AEB) with
Pedestrian Detection (if so equipped) . . . . . . . . . . . 5-98
Turning the AEB with Pedestrian
Detection system on/off . . . . . . . . . . . . . . . . . . . 5-102
System temporarily unavailable . . . . . . . . . . . . 5-105
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . 5-106
System maintenance. . . . . . . . . . . . . . . . . . . . . . . 5-107
Intelligent Forward Collision Warning (I-FCW). . . 5-108
I-FCW system operation . . . . . . . . . . . . . . . . . . . . 5-110
Turning the I-FCW system on/off . . . . . . . . . . . . 5-111
I-FCW system limitations . . . . . . . . . . . . . . . . . . . 5-112
System temporarily unavailable . . . . . . . . . . . . .5-117
System malfunction . . . . . . . . . . . . . . . . . . . . . . . . 5-118
System maintenance. . . . . . . . . . . . . . . . . . . . . . . 5-118
Intelligent Driver Alertness (I-DA) . . . . . . . . . . . . . . . 5-120
How to enable/disable the Intelligent
Driver Alertness (I-DA) system . . . . . . . . . . . . . . 5-122
Break-in schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-123
Fuel efficient driving tips . . . . . . . . . . . . . . . . . . . . . . . 5-124
Increasing fuel economy . . . . . . . . . . . . . . . . . . . . . . 5-125
All-Wheel Drive (AWD) (if so equipped) . . . . . . . . . . 5-125
Parking/parking on hills . . . . . . . . . . . . . . . . . . . . . . . 5-128
Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-129
Brake system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-130
Brake precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 5-130
Anti-lock Braking System (ABS) . . . . . . . . . . . . . 5-131
Brake Assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-132
Vehicle Dynamic Control (VDC) system . . . . . . . . 5-132
Rise-up and build-up . . . . . . . . . . . . . . . . . . . . . . . 5-134
Brake force distribution . . . . . . . . . . . . . . . . . . . . . 5-134
Hill start assist system. . . . . . . . . . . . . . . . . . . . . . . . . 5-135
Front and rear sonar system (if so equipped) . . 5-136
Cold weather driving . . . . . . . . . . . . . . . . . . . . . . . . . . 5-138
Freeing a frozen door lock . . . . . . . . . . . . . . . . . . 5-138
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-138
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-138
Draining of coolant water. . . . . . . . . . . . . . . . . . . 5-138
Tire equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-138
Special winter equipment . . . . . . . . . . . . . . . . . . 5-138
Driving on snow or ice . . . . . . . . . . . . . . . . . . . . . . 5-139
Engine block heater (if so equipped) . . . . . . . . 5-139
PRECAUTIONS WHEN STARTING AND
DRIVING
WARNING
∙ Do not leave children or adults who would normally require the assistance of others alone in your vehicle.
Pets should also not be left alone.
They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
∙ Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury.
∙ Exceeding the roof rack capacity can change the vehicle’s center of gravity and adversely affect the handling and stability of the vehicle resulting in an accident causing death or serious injury.
EXHAUST GAS (carbon monoxide)
WARNING
∙ Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon monoxide is dangerous. It can cause unconsciousness or death.
∙ If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.
∙ Do not run the engine in closed spaces such as a garage.
∙ Do not park the vehicle with the engine running for any extended length of time.
∙ Keep the liftgate and rear vent windows closed while driving, otherwise exhaust gases could be drawn into the passenger compartment. If you must drive with the liftgate or rear vent windows open, follow these precautions:
1. Open all the windows.
2. Set the air recirculation button to off and the fan control dial to high to circulate the air.
∙ If electrical wiring or other cable connections must pass to a trailer through the seal on the liftgate or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.
∙ The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service.
b. You suspect that exhaust fumes are entering into the passenger compartment.
c. You notice a change in the sound of the exhaust system.
d. You have had an accident involving damage to the exhaust system, underbody, or rear of the vehicle.
5-4
Starting and driving
THREE-WAY CATALYST
The three-way catalyst is an emission control device installed in the exhaust system.
Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.
WARNING
∙ The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the components.
exhaust system
∙ Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
CAUTION
∙ Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants.
∙ Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle inspected promptly. It is recommended that you visit a NISSAN dealer for this service.
∙ Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the three-way catalyst.
∙ Do not race the engine while warming it up.
∙ Do not push or tow your vehicle to start the engine.
TIRE PRESSURE MONITORING
SYSTEM (TPMS)
Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with a Tire Pressure
Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when the system is not operating properly.
The TPMS malfunction indicator is combined with the low tire pressure telltale.
Starting and driving
5-5
When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Additional information:
∙ When replacing a wheel without the
TPMS such as the spare tire, the TPMS does not monitor the tire pressure of the spare tire.
∙ The TPMS will activate only when the vehicle is driven at speeds above 16 mph
(25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example, a flat tire while driving).
5-6
Starting and driving
∙ The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 mph (25 km/h) to activate the
TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.
∙ The “Tire Pressure Low — Add Air” warning appears in the vehicle information display when the low tire pressure warning light is illuminated and low tire pressure is detected. The “Tire Pressure
Low — Add Air” warning turns off when the low tire pressure warning light turns off.
∙ The “Tire Pressure Low — Add Air” warning appears each time the ignition switch is placed in the ON position as long as the low tire pressure warning light remains illuminated.
∙ The “Tire Pressure Low — Add Air” warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction.
∙ Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature.
Do not reduce the tire pressure after driving because the tire pressure rises after driving. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate. If the warning light illuminates, check the tire pressure for all four tires.
∙ The Tire and Loading Information label is located in the driver’s door opening.
∙ You can also check the pressure of all tires (except the spare tire) on the vehicle information display screen. The order of the tire pressure figures displayed on the screen corresponds with the actual order of the tire position.
For additional information, refer to “Low tire pressure warning light” in the “Instruments and controls” section and “Tire Pressure
Monitoring System (TPMS)” in the “In case of emergency” section of this manual.
WARNING
∙ Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use.
∙ If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with underinflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light off. If you have a flat tire, replace it with a spare tire as soon as possible. (For additional information on changing a flat tire, refer to
“Flat tire” in the “In case of emergency” section of this manual.)
∙ When replacing a wheel without the
TPMS such as the spare tire, when a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute.
Have your tires replaced and/or TPMS system reset as soon as possible. It is recommended that you visit a NISSAN dealer for this service.
∙ Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.
∙ Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.
CAUTION
∙ The TPMS may not function properly when the wheels are equipped with tire chains or the wheels are buried in snow.
∙ Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor reception of the signals from the tire pressure sensors, and the TPMS will not function properly.
Some devices and transmitters may temporarily interfere with the operation of the
TPMS and cause the low tire pressure warning light to illuminate.
Some examples are:
∙ Facilities or electric devices using similar radio frequencies are near the vehicle.
∙ If a transmitter set to similar frequencies is being used in or near the vehicle.
∙ If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle.
The low tire pressure warning light may illuminate in the following cases:
∙ If the vehicle is equipped with a wheel and tire without TPMS.
∙ If the TPMS has been replaced and the
ID has not been registered.
Starting and driving
5-7
∙ If the wheel is not originally specified by
NISSAN.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For Canada:
This device complies with Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
TPMS with Easy-Fill Tire Alert
When adding air to an under-inflated tire, the TPMS with Easy-Fill Tire Alert provides visual and audible signals outside the vehicle to help you inflate the tires to the recommended COLD tire pressure.
Vehicle set-up
1. Park the vehicle in a safe and level place.
2. Apply the parking brake and place the shift lever in the P (Park) position.
3. Place the ignition switch in the ON position. Do not start the engine.
Operation
1. Add air to the tire.
2. After a few seconds, the hazard indicators will start flashing.
3. When the designated pressure is reached, the horn beeps once and the hazard indicators stop flashing.
4. Perform the above steps for each tire.
∙ If the tire is over-inflated more than approximately 4 psi (30 kPa), the horn beeps and the hazard indicators flash three times. To correct the pressure, push the core of the valve stem
5-8
Starting and driving
on the tire briefly to release pressure.
When the pressure reaches the designated pressure, the horn beeps once.
∙ If the hazard indicator does not flash within approximately 15 seconds after starting to inflate the tire, it indicates that the Easy-Fill Tire Alert is not operating.
∙ The TPMS will not activate the Easy-
Fill Tire Alert under the following conditions:
– If there is interference from an external device or transmitter.
– The air pressure from the inflation device is not sufficient to inflate the tire.
– There is a malfunction in the TPMS.
– There is a malfunction in the horn or hazard indicators.
– The identification code of the tire pressure sensor is not registered to the system.
– The battery of the tire pressure sensor is low.
∙ If the Easy-Fill Tire Alert does not operate due to TPMS interference, move the vehicle about 3 ft (1 m) backward or forward and try again.
If the Easy-Fill Tire Alert is not working, use a tire pressure gauge.
ON-PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher rollover rate than other types of vehicles.
They have higher ground clearance than passenger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a higher center of gravity than ordinary vehicles. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional 2-Wheel
Drive vehicles any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. If at all possible, avoid sharp turns at high speeds.
As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
For additional information, refer to “Driving safety precautions” in this section.
AVOIDING COLLISION AND
ROLLOVER
WARNING
Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.
Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle.
As with any vehicle, loss of control could result in a collision with other vehicles or objects or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide sideways.
Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual, and also instruct your passengers to do so.
Seat belts help reduce the risk of injury in collisions and rollovers.
In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels may unintentionally leave the road surface. If this occurs, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.
Starting and driving
5-9
4. When appropriate, slowly release the accelerator pedal to gradually slow the vehicle.
5. If there is nothing in the way, steer the vehicle to follow the road while vehicle speed is reduced. Do not attempt to drive the vehicle back onto the road surface until vehicle speed is reduced.
6. When it is safe to do so, gradually turn the steering wheel until both tires return to the road surface. When all tires are on the road surface, steer the vehicle to stay in the appropriate driving lane.
∙ If you decide that it is not safe to return the vehicle to the road surface based on vehicle, road or traffic conditions, gradually slow the vehicle to a stop in a safe place off the road.
RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can occur if the tire is punctured or is damaged due to hitting a curb or pothole. Rapid air pressure loss can also be caused by driving on under-inflated tires.
Rapid air pressure loss can affect the handling and stability of the vehicle, especially at highway speeds.
5-10
Starting and driving
Help prevent rapid air pressure loss by maintaining the correct air pressure and visually inspecting the tires for wear and damage. For additional information, refer to “Wheels and tires” in the “Do-it-yourself ” section of this manual. If a tire rapidly loses air pressure or “blows-out” while driving, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic.
WARNING
If there is a sudden loss of tire air pressure, the vehicle will generally move or pull in the direction of the flat tire. In this situation, losing control of the vehicle may cause a collision and result in personal injury.
To help avoid loss of control:
∙ Do not rapidly apply the brakes.
∙ Do not rapidly release the accelerator pedal.
∙ Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.
3. When appropriate, slowly release the accelerator pedal to gradually slow the vehicle.
4. Gradually steer the vehicle to a safe location off the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually stop the vehicle.
6. Turn on the hazard warning flashers and contact a roadside emergency service to change the tire. For additional information, refer to “Changing a flat tire” in the “In case of emergency” section of this manual.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.
NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related collisions. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.
Remember, drinking and driving don’t mix!
That is true for drugs (over-the-counter, prescription) and illegal drugs, too. Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.
DRIVING SAFETY PRECAUTIONS
Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road vehicle.
Remember that 2-Wheel Drive (2WD) models are less capable than All-Wheel Drive
(AWD) models for rough road driving and extrication when stuck in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
∙ Spinning the front wheels on slippery surfaces may cause the AWD warning message to display and the AWD system to automatically switch from the
AWD to the 2WD mode. This could reduce the traction. Be especially careful when towing a trailer (AWD models).
∙ Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.
∙ Do not drive across steep slopes. Instead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.
∙ Many hills are too steep for any vehicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.
∙ Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle.
∙ Stay alert when driving to the top of a hill. At the top there could be a dropoff or other hazard that could cause an accident.
Starting and driving
5-11
∙ If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear and apply brakes to control your speed.
∙ Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low gear to control your speed.
∙ Unsecured cargo can be thrown around when driving over rough terrain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passengers.
∙ Exceeding the roof rack capacity can raise the center of gravity excessively and affect the handling and stability of the vehicle.
∙ Secure heavy loads in the cargo area as far forward and as low as possible.
Do not equip the vehicle with tires larger than specified in this manual.
This could cause your vehicle to roll over.
∙ Do not grip the inside or spokes of the steering wheel when driving off-road.
The steering wheel could move suddenly and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim.
∙ Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.
∙ Always drive with the floor mats in place as the floor may become hot.
∙ Lower your speed when encountering strong crosswinds. With a higher center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.
∙ Do not drive beyond the performance capability of the tires, even with AWD engaged.
∙ For AWD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or unexpected vehicle movement which could result in serious vehicle damage or personal injury.
5-12
Starting and driving
∙ Do not attempt to test an AWD equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for emissions testing) or similar equipment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with AWD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unexpected vehicle movement which could result in serious vehicle damage or personal injury.
∙ When a wheel is off the ground due to an unlevel surface, do not spin the wheel excessively.
∙ Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.
∙ If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your NISSAN vehicle has a higher center of gravity than a passenger car. The vehicle is not designed for cornering at the same speeds as passenger cars.
PUSH-BUTTON IGNITION SWITCH
∙ Failure to operate this vehicle correctly could result in loss of control and/or a rollover accident.
∙ Always use tires of the same type, size, brand, construction (bias, biasbelted, or radial), and tread pattern on all four wheels. Install tire chains on the front wheels when driving on slippery roads and drive carefully.
∙ Be sure to check the brakes immediately after driving in mud or water. For additional information, refer to “Brake precautions” in this section.
∙ Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured.
∙ Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. For additional information, refer to “Maintenance under severe operating conditions” in the “Maintenance and schedules” section of this manual.
LSD2014
WARNING
Do not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed three consecutive times in less than
1.5 seconds or the ignition switch is pushed and held for more than 2 seconds.) If the engine stops while the vehicle is being driven, this could lead to a crash and serious injury.
When the ignition switch is pushed without depressing the brake pedal, the ignition switch will illuminate.
If the ignition switch is in the LOCK or OFF position, push the ignition switch center:
∙ Once to change to ACC.
∙ Two times to change to ON.
∙ Three times to change to OFF.
The shift lever can be moved from the P
(Park) position if the ignition switch is in the ON position and the brake pedal is depressed.
If the battery of the vehicle is discharged, the ignition switch cannot be moved from the LOCK position.
Some indicators and warnings for operation are displayed on the vehicle information display. For additional information, refer to “Vehicle information display” in the
“Instruments and controls” section of this manual.
Starting and driving
5-13
LSD2020
OPERATING RANGE
The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range.
When the Intelligent Key battery is almost discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower and may not function properly.
If the Intelligent Key is within the operating range, it is possible for anyone, even someone who does not carry the Intelligent Key, to push the ignition switch to start the engine.
5-14
Starting and driving
The operating range of the engine start function is inside of the vehicle
䊊
.
∙ The luggage area is not included in the operating range, but the Intelligent Key may function.
∙ If the Intelligent Key is placed on the instrument panel or inside the glove box, storage bin or door pocket, the Intelligent Key may not function.
∙ If the Intelligent Key is placed near the door or window outside the vehicle, the
Intelligent Key may function.
PUSH-BUTTON IGNITION SWITCH
POSITIONS
LOCK (Normal parking position)
The ignition switch can only be locked in this position.
The ignition switch will be unlocked when it is pushed to the ACC position while carrying the Intelligent Key.
The ignition switch will lock when any door is opened or closed with the ignition switched off.
ACC (Accessories)
This position activates electrical accessories, such as the radio, when the engine is not running.
ACC has a battery saver feature that will turn the ignition switch to the OFF position after a period of time under the following conditions:
∙ All doors are closed.
∙ The shift lever is in P (Park).
∙ The hazard lamps are off.
∙ The turn signals are off.
The battery saver feature will be canceled if any of the following occur:
∙ Any door is opened.
∙ The shift lever is moved out of P (Park).
∙ The ignition switch changes position.
∙ The hazard lamps are turned on.
ON (Normal operating position)
This position turns on the ignition system and electrical accessories.
ON has a battery saver feature that will turn the ignition switch to the OFF position, if the vehicle is not running, after some time under the following conditions:
∙ All doors are closed.
∙ The shift lever is in P (Park).
∙ The hazard lamps are off.
∙ The turn signals are off.
The battery saver feature will be canceled if any of the following occur:
∙ Any door is opened.
∙ The shift lever is moved out of the P
(Park) position.
∙ The ignition switch changes position.
∙ The hazard lamps are turned on.
∙ The turn signals are turned on.
CAUTION
Do not leave the vehicle with the ignition switch in the ACC or ON position when the engine is not running for an extended period. This can discharge the battery.
OFF
The ignition switch is in the OFF position when the engine is turned off using the ignition switch. The ignition switch heart beat function (pulsed illumination) may activate for a period of time when any door is unlocked and when the door opened/closed status changes in the OFF and ACC positions.
EMERGENCY ENGINE SHUT OFF
To shut off the engine in an emergency situation while driving, perform the following procedure:
∙ Rapidly push the ignition switch three consecutive times in less than 1.5 seconds, or
∙ Push and hold the ignition switch for more than 2 seconds.
SSD0860
NISSAN INTELLIGENT KEY®
BATTERY DISCHARGE
If the battery of the NISSAN Intelligent Key® is discharged, or environmental conditions interfere with the Intelligent Key operation, start the engine according to the following procedure:
1. Place the shift lever in the P (Park) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key as illustrated. (A chime will sound.)
Starting and driving
5-15
BEFORE STARTING THE ENGINE
(After step 3 is performed, when the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change to ON.)
4. Push the ignition switch while depressing the brake pedal within 10 seconds after the chime sounds. The engine will start.
NOTE:
∙
When the ignition switch is pushed to the ON position or the engine is started by the above procedure, the
Intelligent Key battery discharge indicator appears in the vehicle information display even when the Intelligent Key is inside the vehicle. This is not a malfunction. To turn off the Intelligent Key battery discharge indicator, touch the ignition switch with the Intelligent Key again.
∙
If the Intelligent Key battery discharge indicator appears, replace the battery as soon as possible. For additional information, refer to “Battery replacement” in the “Do-it-yourself ” section of this manual.
NISSAN VEHICLE IMMOBILIZER
SYSTEM
The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.
If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following procedure:
1. Leave the ignition switch in the ON position for approximately 5 seconds.
2. Place the ignition switch in the OFF or
LOCK position, and wait approximately
10 seconds.
3. Repeat steps 1 and 2.
4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.
If the no start condition re-occurs, NISSAN recommends placing the registered key on a separate key ring to avoid interference from other devices.
∙ Make sure the area around the vehicle is clear.
∙ Check fluid levels such as engine oil, coolant, brake fluid, and windshieldwasher fluid as frequently as possible, or at least whenever you refuel.
∙ Check that all windows and lights are clean.
∙ Visually inspect tires for their appearance and condition. Also check tires for proper inflation.
∙ Check that all doors are closed.
∙ Position seat and adjust head restraints/headrests.
∙ Adjust inside and outside mirrors.
∙ Fasten seat belts and ask all passengers to do likewise.
∙ Check the operation of warning lights when the ignition switch is placed in the
ON position. For additional information, refer to “Warning lights, indicator lights and audible reminders” in the “Instruments and controls” section of this manual.
5-16
Starting and driving
STARTING THE ENGINE
1. Apply the parking brake.
2. Move the shift lever to P (Park) or N
(Neutral). P (Park) is recommended.
The starter is designed not to operate unless the shift lever is in either P
(Park) or N (Neutral).
3. Push the ignition switch to the ON position. Depress the brake pedal and push the ignition switch to start the engine.
To start the engine immediately, push and release the ignition switch while depressing the brake pedal with the ignition switch in any position.
∙ If the engine is very hard to start in extremely cold weather or when restarting, depress the accelerator pedal a little (approximately 1/3 to the floor) and while holding, crank the engine. Release the accelerator pedal when the engine starts.
∙ If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Push the ignition switch to the ON position to start cranking the engine. After 5 or 6 seconds, stop cranking by pushing the ignition switch to the LOCK position. After cranking the engine, release the accelerator pedal. Crank the engine with your foot off the accelerator pedal by depressing the brake pedal and pushing the ignition switch to start the engine. If the engine starts, but fails to run, repeat the above procedure.
CAUTION
Do not operate the starter for more than 15 seconds at a time. If the engine does not start, push the ignition switch to the OFF position and wait 10 seconds before cranking again, otherwise the starter could be damaged.
4.
Warm-up:
Allow the engine to idle for at least
30 seconds after starting. Do not race the engine while warming it up. Drive at a moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2 to 3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start.
5. To stop the engine, move the shift lever into the P (Park) position and push the ignition switch to the OFF position.
NOTE:
Care should be taken to avoid situations that can lead to potential battery discharge and potential no-start conditions such as:
1.
Installation or extended use of electronic accessories that consume battery power when the engine is not running (phone chargers, GPS, DVD players, etc.).
2.
The vehicle is not driven regularly and/or only driven short distances
In these cases, the battery may need to be charged to maintain battery health.
Starting and driving
5-17
DRIVING THE VEHICLE
REMOTE ENGINE START (if so equipped)
Vehicles started with the Remote Engine
Start require the ignition switch to be placed in the ON position before the shift lever can be moved from the P (Park) position. To place the ignition switch in the ON position, follow these steps:
1. Make sure that the Intelligent Key is on you.
2. Apply the brake.
3. Push the ignition switch once to the ON position.
For additional information, refer to “NISSAN
Intelligent Key®” in the “Pre-driving checks and adjustments” section of this manual.
CONTINUOUSLY VARIABLE
TRANSMISSION (CVT)
WARNING
∙ Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), or M
(Manual shift mode). Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.
∙ Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.
∙ Do not downshift abruptly on slippery roads. This may cause a loss of control.
∙ Never shift to either the P (Park) or R
(Reverse) position while the vehicle is moving forward and P (Park) or D
(Drive) position while the vehicle is reversing. This could cause an accident or damage the transmission.
CAUTION
∙ To avoid possible damage to your vehicle, when stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.
∙ Except in an emergency, do not shift to the N (Neutral) position while driving. Coasting with the transmission in the N (Neutral) position may cause serious damage to the transmission.
The CVT in your vehicle is electronically controlled to produce maximum power and smooth operation.
The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment.
Engine power may be automatically reduced to protect the CVT if the engine speed increases quickly when driving on slippery roads or while being tested on some dynamometers.
5-18
Starting and driving
Starting the vehicle
1. After starting the engine, fully depress the foot brake pedal before moving the shift lever out of the P (Park) position.
This Continuously Variable Transmission is designed so that the foot brake pedal must be depressed before shifting from P (Park) to any driving position while the ignition switch is in the ON position.
The shift lever cannot be moved out of the P (Park) position and into any of the other positions if the ignition switch is placed in the LOCK, OFF or
ACC position.
2. Keep the foot brake pedal depressed and move the shift lever to a driving position.
3. Release the parking brake and foot brake pedal, and then gradually start the vehicle in motion.
WARNING
∙ Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), or M
(Manual shift mode) position. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.
∙ Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.
∙ Never shift to either the P (Park) or R
(Reverse) position while the vehicle is moving forward and P (Park) or D
(Drive) position while the vehicle is reversing. This could cause an accident or damage the transmission.
∙ Do not downshift abruptly on slippery roads. This may cause a loss of control.
CAUTION
∙ To avoid possible damage to your vehicle, when stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.
∙ Except in an emergency, do not shift to the N (Neutral) position while driving. Coasting with the transmission in the N (Neutral) position may cause serious damage to the transmission.
Starting and driving
5-19
LSD3162
Shifting
After starting the engine, fully depress the brake pedal, press the shift lever button and move the shift lever from the P (Park) position to any of the desired shift positions.
WARNING
Apply the parking brake if the shift lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.
5-20
Starting and driving
CAUTION
Use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.
P (Park)
CAUTION
To prevent transmission damage, use the P (Park) position only when the vehicle is completely stopped.
Use the P (Park) shift lever position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped.
The brake pedal must be depressed and the shift lever button pressed in to move the shift lever from N
(Neutral) or any drive position to P (Park).
Apply the parking brake. When parking on a hill, apply the parking brake first, then move the shift lever into the P (Park) position.
R (Reverse)
CAUTION
To prevent transmission damage, use the R (Reverse) position only when the vehicle is completely stopped.
Use the R (Reverse) position to back up.
Make sure the vehicle is completely stopped before selecting the R (Reverse) position.
The brake pedal must be depressed and the shift lever button pressed in to move the shift lever from P
(Park), N (Neutral) or any drive position to
R (Reverse).
N (Neutral)
Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving.
D (Drive)
Use this position for all normal forward driving.
LSD2489
Manual shift mode
When the shift lever is in the manual shift gate, the transmission is ready for the manual shift mode. Shift ranges can be selected manually by moving the shift lever up or down. To cancel manual shift mode, return the shift lever to the D (Drive) position. The transmission returns to automatic driving mode.
When the shift lever is shifted from D (Drive) to the manual shift gate with the vehicle stopped or while driving, the transmission enters the manual shift mode. Shift ranges can be selected manually. In the manual shift mode, the shift range is displayed on the position indicator in the meter. When moving the shift lever to the manual shift gate, the position indicator displays 1 (First) up to 7 (Seventh) depending on vehicle speed.
Shift ranges up or down one by one as follows:
1
⇔
2
⇔
3
⇔
4
⇔
5
⇔
6
⇔
7
7 (Seventh)
Use this position for all normal forward driving at highway speeds.
6 (Sixth) and 5 (Fifth)
Use this position when driving up long slopes, or for engine braking when driving down long slopes.
4 (Fourth), 3 (Third) and 2 (Second)
Use these positions for hill climbing or engine braking on downhill grades.
1 (First)
Use this position when climbing steep hills slowly or when driving slowly, or for maximum engine braking on steep downhill grades.
∙ Remember not to drive at high speeds for extended periods of time in lower than seventh gear. This reduces fuel economy.
When shifting up
Move the shift lever to the + (up) side. (Shifts to higher range.)
When shifting down
Move the shift lever to the
⫺
(down) side.
(Shifts to lower range.)
∙ The transmission will automatically downshift the gears. (For example, if you select the third range, the transmission will shift down between the third and first gears.)
∙ Moving the shift lever rapidly to the same side twice will shift the ranges in succession.
When canceling the manual shift mode
Return the shift lever to the D (Drive) position to return the transmission to the normal driving mode.
Starting and driving
5-21
∙
In the manual shift mode, the transmission may not shift to the selected gear. This helps maintain driving performance and reduces the chance of vehicle damage or loss of control.
∙
When this situation occurs, the Continuously Variable Transmission (CVT) position indicator light will blink and the chime will sound.
∙
In the manual shift mode, the transmission may shift up automatically to a higher range than selected if the engine speed is too high. When the vehicle speed decreases, the transmission automatically shifts down and shifts to first gear before the vehicle comes to a stop.
∙ CVT operation is limited to automatic drive mode when CVT fluid temperature is extremely low even if manual shift mode is selected. This is not a malfunction. When CVT fluid warms up, manual mode can be selected.
∙ When the CVT fluid temperature is high, the shift range may upshift in lower rpm than usual. This is not a malfunction.
LSD3163
Shift lock release
If the battery charge is low or discharged, the shift lever may not be moved from the
P (Park) position even with the brake pedal depressed and the shift lever button pressed. To move the shift lever, perform the following procedure:
1. Place the ignition switch in the OFF or
LOCK position.
2. Apply the parking brake.
3. Remove the shift lock release cover using a suitable tool.
5-22
Starting and driving
4. Push down the shift lock release using a suitable tool.
5. Press the shift lever button and move the shift lever to the N (Neutral) position while holding down the shift lock release. The vehicle may be moved to the desired location. Replace the removed shift lock release cover after the operation. If the shift lever cannot be moved out of the P (Park) position, have the
Continuously Variable Transmission system checked as soon as possible. It is recommended that you visit a
NISSAN dealer for this service.
WARNING
If the shift lever cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work.
Malfunctioning stop lights could cause an accident injuring yourself and others.
PARKING BRAKE
Accelerator downshift
— in D (Drive) position —
For passing or hill climbing, depress the accelerator pedal to the floor. This shifts the transmission down into a lower gear, depending on the vehicle speed.
High fluid temperature protection mode
This transmission has a high fluid temperature protection mode. If the fluid temperature becomes too high (for example, when climbing steep grades in high temperatures with heavy loads, such as when towing a trailer), engine power and, under some conditions, vehicle speed will be decreased automatically to reduce the chance of transmission damage. Vehicle speed can be controlled with the accelerator pedal, but the engine and vehicle speed may be limited.
Fail-safe
If the vehicle is driven under extreme conditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated.
The Malfunction Indicator Light (MIL) may come on to indicate the fail-safe mode is activated. For additional information, refer to “Malfunction Indicator
Light (MIL)” in the “Instruments and controls” section of this manual. This will occur even if all electrical circuits are functioning properly. In this case, place the ignition switch in the OFF position and wait for 10 seconds. Then push the switch back to the ON position. The vehicle should return to its normal operating condition. If it does not return to its normal operating condition, have the transmission checked and repaired, if necessary. It is recommended that you visit a NISSAN dealer for this service.
WARNING
When the high fluid temperature protection mode or fail-safe operation occurs, vehicle speed may be gradually reduced. The reduced speed may be lower than other traffic, which could increase the chance of a collision. Be especially careful when driving. If necessary, pull to the side of the road at a safe place and allow the transmission to return to normal operation, or have it repaired if necessary.
LSD0158
WARNING
∙ Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.
∙ Do not release the parking brake from outside the vehicle.
∙ Do not use the shift lever in place of the parking brake. When parking, be sure the parking brake is fully engaged.
Starting and driving
5-23
TRAFFIC SIGN RECOGNITION (TSR) (if so equipped)
∙ To help avoid risk of injury or death through unintended operation of the vehicle and/or its systems, do not leave children, people who require the assistance of others or pets unattended in your vehicle. Additionally, the temperature inside a closed vehicle on a warm day can quickly become high enough to cause a significant risk of injury or death to people and pets.
To engage:
Firmly depress the parking brake.
To release:
1. Firmly apply the foot brake.
2. Move the shift lever to the P (Park) position.
3. Firmly depress the parking brake pedal and it will release.
4. Before driving, be sure the brake warning light goes out.
LSD3360
The TSR system provides the driver with information about the most recently detected speed limit. The system captures the road sign information with the multisensing front camera unit
䊊 located on the windshield in front of the inside rearview mirror and displays the detected signs in the vehicle information display. For vehicles equipped with a navigation system, the speed limit displayed is based on a combination of navigation system data and live camera recognition. TSR information is always displayed at the top of the vehicle information display if the system is enabled in the Driver Assistance settings.
5-24
Starting and driving
WARNING
The TSR system is only intended to be a support device to provide the driver with information. It is not a replacement for the driver’s attention to traffic conditions or responsibility to drive safely.
It cannot prevent accidents due to carelessness. It is the driver’s responsibility to stay alert and drive safely at all times.
LSD3377
SYSTEM OPERATION
The Traffic Sign Recognition (TSR) system displays the following types of road signs:
䊊
䊊
LSD3378
Speed sign detected (in Canada)
Speed sign detected (in USA)
Speed sign detected (no speed limit detected)
“Do not pass” sign detected
CAUTION
∙ The TSR system is intended as an aid to careful driving. It is the driver’s responsibility to stay alert, drive safely, and observe all road regulations that currently apply, including looking out for road signs.
∙ The TSR system may not function properly under the following conditions:
– When the road sign is not clearly visible, for example, due to damage or weather conditions.
– When rain, snow or dirt adheres to the windshield in front of the multisensing camera unit.
– When the headlights are not bright due to dirt on the lens or if the aiming is not adjusted properly.
– When strong light enters the camera unit. (For example, the light directly shines on the front of the vehicle at sunrise or sunset.)
– When a sudden change in brightness occurs. (For example, when the vehicle enters or exits a tunnel or under a bridge.)
Starting and driving
5-25
– In areas not covered by the navigation system.
– If there are deviations in relation to the navigation, for example due to changes in the road routing.
– When overtaking buses or trucks with speed stickers.
LSD3346
TURNING THE TRAFFIC SIGN
RECOGNITION (TSR) SYSTEM ON
AND OFF
Perform the following steps to enable or disable the TSR system.
1. Press the button until “Settings” displays in the vehicle information display and then press the OK button. Use the button to select “Driver Assistance.” Then press the OK button.
2. Select “Speed Limit Sign” and press the
OK button to turn the system on or off.
SYSTEM TEMPORARILY
UNAVAILABLE
If the vehicle is parked in direct sunlight under high temperature conditions (over approximately 104°F [40°C]) and then started, the TSR system may be deactivated automatically. The “Unavailable: High
Cabin Temperature” warning message will appear in the vehicle information display.
Action to take:
When the interior temperature is reduced, the TSR system will resume operating automatically.
SYSTEM MALFUNCTION
If the TSR system malfunctions, it will be turned off automatically and the LDW indicator (orange) will illuminate in the vehicle information display.
Action to take:
If the LDW indicator (orange) illuminates in the display, pull off the road at a safe location and stop the vehicle. Turn the engine off and restart the engine. If the LDW indicator (orange) continues to illuminate, have the system checked. It is recommended that you visit a NISSAN dealer for this service.
5-26
Starting and driving
SYSTEM MAINTENANCE
The TSR system uses the same multisensing front camera unit that is used by the Lane Departure Warning (LDW) system, located in front of the interior rearview mirror. For additional information, refer to ”System maintenance” in the “Lane Departure
Warning (LDW)” section.
LANE DEPARTURE WARNING (LDW) (if so equipped)
LSD3360
WARNING
Failure to follow the warnings and instructions for proper use of the LDW system could result in serious injury or death.
∙ This system is only a warning device to inform the driver of a potential unintended lane departure. It will not steer the vehicle or prevent loss of control. It is the driver’s responsibility to stay alert, drive safely, keep the vehicle in the traveling lane, and be in control of the vehicle at all times.
The LDW system will operate when the vehicle is driven at speeds of approximately
37 mph (60 km/h) and above, and only when the lane markings are clearly visible on the road.
The LDW system monitors the lane markers on the traveling lane using the camera unit
䊊 located above the inside mirror.
The LDW system warns the driver that the vehicle is beginning to leave the driving lane with an indicator and a steering wheel vibration. For additional information, refer to “LDW system operation” in this section.
Starting and driving
5-27
5-28
Starting and driving
LSD3428
Lane Departure Warning (LDW) indicator
LDW SYSTEM OPERATION
The LDW system provides a lane departure warning function when the vehicle is driven at speeds of approximately 37 mph
(60 km/h) and above and the lane markings are clear. When the vehicle approaches either the left or the right side of the traveling lane, the steering wheel will vibrate and the LDW indicator
䊊 on the instrument panel will blink to alert the driver.
The warning function will stop when the vehicle returns inside of the lane markers.
LSD3429
HOW TO ENABLE/DISABLE THE
LDW SYSTEM
Perform the following steps to enable or disable the LDW system.
Using “Settings” in the vehicle information display:
1. Press the button until “Settings” displays in the vehicle information display and then press the OK button. Use the button to select “Driver Assistance.” Then press the OK button.
2. Select “Lane” and press the OK button.
3. Select “Lane Departure Warning” and press the OK button to turn the system on or off.
Using the “Driving Aids” screen in the vehicle information display:
1. Use the buttons on the steering wheel to scroll to the Driving Aids screen.
2. Press the OK button to access the
Driver Assistance menu.
3. Select “Lane” and press the OK button until “Lane Warning” is displayed.
4. Press the buttons to return to the Driving Aids screen.
Starting and driving
5-29
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the LDW system. Failure to follow the warnings and instructions for proper use of the LDW system could result in serious injury or death.
∙ The system will not operate at speeds below approximately 37 mph (60 km/h) or if it cannot detect lane markers.
∙ Do not use the LDW system under the following conditions as it may not function properly:
– During bad weather (rain, fog, snow, etc.).
– When driving on slippery roads, such as on ice or snow.
– When driving on winding or uneven roads.
– When there is a lane closure due to road repairs.
– When driving in a makeshift or temporary lane.
– When driving on roads where the lane width is too narrow.
5-30
Starting and driving
– When driving without normal tire conditions (for example, tire wear, low tire pressure, installation of spare tire, tire chains, nonstandard wheels).
– When the vehicle is equipped with non-original brake parts or suspension parts.
– When you are towing a trailer or other vehicle.
∙ The system may not function properly under the following conditions:
– On roads where there are multiple parallel lane markers; lane markers that are faded or not painted clearly; yellow painted lane markers; non-standard lane markers; or lane markers covered with water, dirt, snow, etc.
– On roads where the discontinued lane markers are still detectable.
– On roads where there are sharp curves.
– On roads where there are sharply contrasting objects, such as shadows, snow, water, wheel ruts, seams or lines remaining after road repairs. (The LDW system could detect these items as lane markers.)
– On roads where the traveling lane merges or separates.
– When the vehicle’s traveling direction does not align with the lane marker.
– When traveling close to the vehicle in front of you, which obstructs the lane camera unit detection range.
– When rain, snow, dirt or an object adheres to the windshield in front of the lane camera unit.
– When the headlights are not bright due to dirt on the lens or if the aiming is not adjusted properly.
– When strong light enters the lane camera unit. (For example, the light directly shines on the front of the vehicle at sunrise or sunset.)
– When a sudden change in brightness occurs. (For example, when the vehicle enters or exits a tunnel or under a bridge.)
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Comprehensive safety information
Detailed instrument and control descriptions
Pre-driving check guidelines
Monitor, climate, audio, phone, and voice recognition systems guidance
Emergency procedure instructions
Maintenance and care recommendations
Technical and consumer information
Frequently asked questions
Before driving your vehicle, please read this Owner’s Manual carefully to ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle.
Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
If there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions, please contact the NISSAN Consumer Affairs Department using our toll-free number.
This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles (kilometers) of driving pleasure.