Pump Alternation Control Operation. PRECISION DIGITAL PD8-6060 ProtEX-MAX, PD8-6060
Add to My manuals66 Pages
advertisement
▼
Scroll to page 2
of
66
![Pump Alternation Control Operation. PRECISION DIGITAL PD8-6060 ProtEX-MAX, PD8-6060 | Manualzz Pump Alternation Control Operation. PRECISION DIGITAL PD8-6060 ProtEX-MAX, PD8-6060 | Manualzz](http://s3.manualzz.com/store/data/054612342_1-2f9f9cbdbe5eb5683fe869b3acb3fc0f-360x466.png)
ProtEX-MAX PD8-6060 Explosion-Proof Dual-Input Meter Instruction Manual
Pump Alternation Control Operation
Relay Sampling Operation
Input
Set
Reset
Sample
Time
Sample
Time
Sample
Time
Relay
LED
When the signal crosses the set point, the relay trips and the sample time starts. After the sample time has elapsed, the relay resets. The cycle repeats every time the set point is crossed, going up for high alarms and going down for low alarms.
The sample time can be programmed between 0.1 and 5999.9 seconds.
37
advertisement
Related manuals
advertisement
Table of contents
- 3 Table of Contents
- 4 Table of Figures
- 4 Introduction
- 5 Ordering Information
- 5 Specifications
- 5 General
- 6 Dual Process Input
- 7 Relays
- 7 Isolated 4-20 mA Transmitter Output
- 8 Serial Communications
- 8 Digital Inputs & Outputs
- 8 MeterView Pro
- 9 Product Ratings and Approvals
- 10 Compliance Information
- 10 Safety
- 10 Electromagnetic Compatibility
- 11 Safety Information
- 11 Installation
- 11 Unpacking
- 12 Pre-Installed Conduit/Stopping Plug
- 12 Mounting
- 12 Cover Jam Screw
- 12 Transmitter Supply Voltage Selection (P+, P-)
- 13 Connections
- 13 Required & Factory Wired Connection
- 14 Connectors Labeling
- 14 Power Connections
- 15 Signal Connections
- 16 Serial Communications Connections
- 16 Three Wire Connections
- 18 Serial Adapters
- 19 Relay Connections
- 19 Switching Inductive Loads
- 20 F4 Digital Input Connections
- 20 4-20 mA Output Connections
- 20 Analog Output Transmitter Power Supply
- 20 Interlock Relay Feature
- 21 Digital I/O Connections
- 21 External Switch Contacts
- 22 Setup and Programming
- 22 Overview
- 22 Buttons
- 23 Front Buttons and Status LED Indicators
- 24 Pro Software
- 24 MeterView Pro Installation
- 25 Display Functions & Messages
- 27 Main Menu
- 27 Setting Numeric Values
- 30 Pro Software
- 30 Scaling the Meter without a Signal Source
- 31 Calibrating the Meter with External Source
- 35 Setting the Relay Action
- 35 Programming Set and Reset Points
- 35 Setting Fail-Safe Operation
- 35 Programming Time Delay
- 36 Relay and Alarm Operation Diagrams
- 36 High Alarm Operation (Set > Reset)
- 36 Low Alarm Operation (Set < Reset)
- 37 Pump Alternation Control Operation
- 37 Relay Sampling Operation
- 38 Signal Loss or Loop Break Relay Operation
- 38 Time Delay Operation
- 39 Relay Operation Details
- 39 Overview
- 39 Relays Auto Initialization
- 39 Fail-Safe Operation
- 40 Front Panel LEDs
- 40 Latching and Non-Latching Relay Operation
- 41 Acknowledging Relays
- 43 Interlock Relay Operation Example
- 45 Protecting or Locking the Meter
- 45 Disabling Password Protection
- 46 Advanced Features Menu
- 46 Advanced Features Menu & Display Messages
- 48 Noise Filter Bypass (bypass)
- 49 Serial Communications Overview