Installation - AL600
SECTION 2 : INSTALLER
With Removable 3rd Row Seating
1. Remove 3rd Row Seating.
[Figure 14-1]
2. The AL600 Leg must be mounted
between 32” and 42” from the internal surface of the closed back door of the vehicle.
[Figure 14-2]
2nd ROW SEATING
CENTER
32”
42”
3.
Examine the Floor for Additional Seat
Attachment Points.
These must be recessed into the loor. [Figure 14-3]
IMPORTANT:
Attachment Points MUST be FLUSH or LOWER than the loor.
Figure 14-2
Figure 14-1
2nd ROW SEATING
32”
42”
14
Figure 14-3
© 2014 Harmar Mobility, LLC • All Rights Reserved
4 A.
If Seat Attachment Points ARE
Available:
See Figure 15-1 for mounting diagram.
SECTION 2 : INSTALLER
Installation - AL600
With Removable 3rd Row Seating
Mounting
Bracket
3/8 -16 Nyloc Nuts
3/8 Flat Washer
Mounting Bracket
3/8 - 16
J-HOOK
Hex Head Bolt,
1/2-13 x 4.00"L
Fully Threaded
Figure 15-1
4 B. If Seat Attachment Points are NOT
Available:
Look under vehicle in approximate area where Leg will need to be mounted. See
Figure 15-2 for mounting diagram.
Drill a pilot hole irst, up from under the vehicle to ensure nothing will be damaged.
Find hole from inside vehicle and drill 3/8” hole down through vehicle’s loor.
CAUTION
USE EXTREME CAUTION
Avoid Gas Tank, Fuel / Brake / Electrical
Lines
PILOT
HOLE
3/8"
Hex Head Bolt,
3/8 - 16 x 4.00"L
Fully Threaded
Mounting Bracket
3/8"
3/8 Flat
Washer
Mounting
Bracket
Hex Head Bolt,
1/2-13 x 4.00"L
Fully Threaded
Figure 15-2
Installation
Washers
PILOT
HOLE
3/8 - 16
Nyloc Nuts
TEC0020 17Sep14 P/N: 630-00025 revA
AL600 & AL690 Hybrid Installation & Owner's Manual 2014
15
Installation - AL600
SECTION 2 : INSTALLER
With Removable 3rd Row Seating
7.
Place mounting washers on bolts
, on top of mounting lange on lift. Place ½” lock washers onto bolts. Thread ½-13 nuts onto bolts.
5. Thread ½-13 nuts onto ½-13 x 4.00”
L bolts.
Place ½” lock washers onto bolts.
Place mounting washers onto bolts.
1/2-13
Hex Nut
1/2 Split Lock
Washer
Mounting
Washer
6.
Use an assistant
to place lift onto bolts through mounting lange on lift as shown.
Mounting
Washer
1/2 Split Lock
Washer
1/2-13
Hex Nut
(LEVELING NUT)
Mounting
Flange
1/2-13 x 4.00"L bolts
Leveling
Pad w/
Jam Nut
Foot Plate
16
WARNING
If no assistant is available, follow instructions on page 11 to avoid injury.
8. Lift front end of lift and install leveling pads as shown.
Place foot plate under leveling pads. Lower lift and check with a level. Adjust by threading nut on leveling pads and threading bottom nut under mounting lange.
© 2014 Harmar Mobility, LLC • All Rights Reserved
8. Plug hand controller into lift.
[Figure 17-1]
Connect to vehicle harness.
[Figure 17-2]
SECTION 2 : INSTALLER
Installation - AL600
With Removable 3rd Row Seating
Figure 17-1
From vehicle harness
( installed on page 12)
10. Attach platform
by placing platform’s upright pins into u-shaped bracket on tower. [Figure
17-4]
FROM LIFT
BLACK
RED
BLACK
RED
FROM VEHICLE HARNESS
( FROM BATTERY )
Figure 17-2
Figure 17-4
11. Thread ½-13 x 1-3/4” L Hex head Bolts and
9. Press the DOWN button
until the lift’s tower has
½” washers into threaded holes as shown.
[Figure moved out of the vehicle.
[Figure 17-3]
17-5] Test full motion of lift into and out of the vehicle.
Be sure lift is level and no obstructions interfere with platform travel.
Tighten all fasteners from all steps at this time.
Figure 17-5
Figure 17-3
TEC0020 17Sep14 P/N: 630-00025 revA
AL600 & AL690 Hybrid Installation & Owner's Manual 2014
17
