Overview. DFI HU101/HU103

DFI HU101/HU103 is a powerful and versatile industrial motherboard designed for a wide range of applications. It features a Mini-ITX form factor, making it ideal for space-constrained environments. Despite its compact size, the HU101/HU103 is packed with features, including support for Intel® Core™ i7/i5/i3 processors, DDR3 memory, and a variety of expansion options. With its rugged construction and wide range of features, the HU101/HU103 is an excellent choice for industrial automation, medical, and other demanding applications.

PDF

Document

Chapter 3

Chapter 3 - BIOS Setup

Overview

The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals. It contains codes for various advanced features found in this system board.

The BIOS allows you to configure the system and save the configuration in a battery-backed

CMOS so that the data retains even when the power is off. In general, the information stored in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been made such as a hard drive replaced or a device added.

It is possible that the CMOS battery will fail causing CMOS data loss. If this happens, you need to install a new CMOS battery and reconfigure the BIOS settings.

Note:

The BIOS is constantly updated to improve the performance of the system board; therefore the BIOS screens in this chapter may not appear the same as the actual one. These screens are for reference purpose only.

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering the BIOS Setup Utility

The BIOS Setup Utility can only be operated from the keyboard and all commands are keyboard commands. The commands are available at the right side of each setup screen.

The BIOS Setup Utility does not require an operating system to run. After you power up the system, the BIOS message appears on the screen and the memory count begins. After the memory test, the message “Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.

Legends

Keys

Right and Left arrows

Up and Down arrows

<Esc>

+ (plus key)

- (minus key)

Tab

<F1>

<F2>

<F3>

<F4>

<Enter>

Function

Moves the highlight left or right to select a menu.

Moves the hightlight up or down between submenu or fi elds.

Exit to the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted fi eld.

Scrolls backward through the values or options of the highlighted fi eld.

Select a fi eld.

Displays general help

Pervious values

Optimized defaults

Saves and resets the setup program.

Press <Enter> to enter the highlighted submenu.

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “



“ appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press <Enter>.

Chapter 3 BIOS Setup

Chapter 3

AMI BIOS Setup Utility

Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.

Main

Advanced Chipset Boot Security Save & Exit

Choose the system default language

BIOS Information

BIOS Vendor

Core Version

Compliancy

Project Version

Build Date and Time

System Language

System Date

System Time

Access Level

American Megatrends

4.6.5.4

UEFI 2.3.1; PI 1.2

1AQPM 0.34 x64

04/22/2014 18:10:49

[English]

[Fri 04/25/2014]

[14:05:42]

Administraor





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Sunday to Saturday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1980 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to

23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Important:

Setting incorrect field values may cause the system to malfunction.

Main

Advanced Chipset Boot Security Save & Exit

System ACPI Parameters 



ACPI Settings

Trusted Computing

CPU Confi guration





SATA Confi guration

Intel(R) Rapid Start Technology

AMT Confi guration

USB Confi guration





PCH-FW Confi guration

NCT6106D Super IO Confi guration

NCT6106D HW Monitor

Power Failure Control





WatchDog Confi guration

Network Stack



Intel(R) Ethernet Connection I218-LM - 88:88:88:88:87:88......

Intel(R) I210 Gigabit Network Connection - 00:01:29:50:......





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Chapter 3

ACPI Settings

This section is used to configure the system ACPI parameters.

ACPI Settings

Advanced

ACPI Sleep State

Resume by RTC Alarm

[S3 only (Suspend to...)]

[Disabled]

Select ACPI sleep state the system will enter when the SUSPEND button is pressed.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

ACPI Sleep State

Selects the highest ACPI sleep state the system will enter when the Suspend button is pressed.

S1 only (CSC) Enables the CPU Stop Clock.

S3 only (STR) Enables the Suspend to RAM.

Both S1 and S3 available for OS to choose from

Resume by RTC Alarm

When Enabled, the system uses the RTC to generate a wakeup event.

Trusted Computing

This section configures settings relevant to Trusted Computing innovations.

Advanced

Confi guration

Security Device Support

Current Status Information

SUPPORT TURNED OFF

[Disable]

Enables or Disables

BIOS support for security device. O.S will not show

Security Device. TCG

EFI protocol and INT1A interface will not be available.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Security Device Support

This field is used to enable or disable BIOS supporting for the security device. O.S will not show the security device. TCG EFI protocol and INT1A interface will not be available.

Chapter 3 BIOS Setup

Chapter 3

CPU Configuration

This section is used to configure the CPU. It will also display the detected CPU information.

Advanced

CPU Confi guration Number of cores to enable in each processor package.

Intel(R) Core(TM) i7-4650U CPU @1.70GHz

CPU Signature

Processor Family

Microcode Patch

FSB Speed

Max CPU Speed

Min CPU Speed

CPU Speed

Processor Cores

Intel HT Technology

Intel VT-X Technology

Intel SMX Technology

64-bit

EIST Technology

CPU C3 State

CPU C6 State

CPU C7 State

40651

100 MHz

1600 MHz

800 MHz

1600 MHz

Not Supported

Supported

Not Supported

Supported

L1 Data Cache

L1 Code Cache

L2 Cache

L3 Cache

32 KB x2

256 KB x2

2048 KB

Active Processor Cores

Limit CPUID Maximum

Intel Virtualization Technology

Boot Performance Mode

EIST

[All]

[Disabled]

[Enabled]

[Max Non-Turbo Perfo...]

[Enabled]





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Active Processor Cores

Number of cores to enable in each processor package.

Limit CPUID Maximum

Disabled for Windows XP.

Intel Virtualization Technology

When this field is set to Enabled, the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

Boot Performance Mode

Selects the performance state that the BIOS will set before OS handoff.

EIST

This field is used to enable or disable the Intel Enhanced SpeedStep Technology.

Chapter 3 BIOS Setup

SATA Configuration

This section is used to configure the settings of SATA device.

Advanced

SATA Controller(s)

SATA Mode Selection

Serial ATA Port 0

Software Preserve

Port 0

SATA Device Type

Serial ATA Port 1

Software Preserve

Port 1

SATA Device Type

Serial ATA Port 2

Software Preserve

Port 2

SATA Device Type

Serial ATA Port 3

Software Preserve

Port 3

SATA Device Type

[Enabled]

[AHCI]

Empty

Unknown

[Enabled]

[Hard Disk Drive]

ST160LT007-92V (160.0GB)

SUPPORTED

[Enabled]

[Hard Disk Drive]

Empty

Unknown

[Enabled]

[Hard Disk Drive]

Empty

Unknown

[Enabled]

[Hard Disk Drive]

Enable or disable SATA

Device.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

SATA Controller(s)

This field is used to enable or disable Serial ATA devices.

SATA Mode Selection

The mode selection determines how the SATA controller(s) operates.

AHCI Mode

This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Interface).

RAID Mode

This option allows you to create RAID or Intel Matrix Storage configuration on Serial

ATA devices.

Port 0/1/2/3

This field is used to enable or disable the serial ATA port.

SATA Device Type

Identify the serial ATA port which is connected to the Solid State Drive or the Hard

Disk Drive.

Intel(R) Rapid Start Technology

This section is used to enable or disable the Intel Rapid Start Technology.

Advanced

Intel(R) Rapid Start Technology [Disabled] Enable or disable Intel(R)

Rapid Start Technology





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

When enabled, it will display the following information.

Advanced

Intel(R) Rapid Start Technology

No valid partition

Entry on S3 RTC Wake

Entry After

Active Page Threshold Support

Hybrid Hard Disk Support

Rapid Start Display Save/Restore

[Enabled]

[Disabled]

Enable or disable Intel(R)

Rapid Start Technology





Enter:

+/-:

F1:

F2:

Select Screen

Select Item

Select

Change Opt.

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Chapter 3

Entry on S3 RTC Wake

This field is used to enable or disable the rapid start invocation upon S3 RTC wake.

Entry After

Enables RTC wake timer at S3 entry. Enters the value range from 0 (immediately) to

120 minutes.

Active Page Threshold Support

This field is used to support RST with small partition.

Hybrid Hard Disk Support

Enables or disables the hybrid hard disk support.

Rapid Start Display Save/Restore

Enables or disables the rapid start display save or restore.

Chapter 3 BIOS Setup

AMT Configuration

This section configures the parameters of Active Management Technology.

Intel AMT

Hide Un-Confi gure ME Confi rmation

Advanced

[Enabled]

[Disabled]

Enable/ Disable Intel(R)

Active Management Technology BIOS Extension.

Note: iAMT H/W is always enabled.

This option just controls the BIOS extension execution. If enabled, this requires additional fi rmware in the SPI device.





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Intel AMT

Enables or disables the AMT function.

Hide Un-Configure ME Confirmation

OEMFlag Bit 6: Hide Un-configure ME without the password confirmation prompt.

Chapter 3

USB Configuration

This section is used to configure the parameters of the USB device.

USB Devices:

1 Keyboard, 1 Mouse, 2 Hubs

Legacy USB Support

EHCI Hand-off

Advanced

USB Confi guration

USB Module Version 8.10.28

[Enabled]

[Disabled]

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for

EFI applications.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Legacy USB Support

Enabled

Enables legacy USB.

Disabled

Keeps USB devices available only for EFI applications.

Auto

Disables support for legacy when no USB devices are connected.

EHCI Hand-off

This is a workaround for OSes without the EHCI hand-off support. The EHCI ownership change should be claimed by the EHCI driver.

Chapter 3 BIOS Setup

PCH-FW Configuration

This section only displays the parameters of Management Engine Technology.

Advanced

ME FW Version

ME Firmware Mode

ME Firmware Type

ME Firmware SKU

PTT Capability/State

9.5.30.1808

Normal Mode

Full Sku Firmware

5MB

1/0





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3

NCT6106D Super IO Configuration

This section is used to configure the I/O functions supported by the onboard Super I/O chip.

Advanced

OS Select

Super IO Confi guration

Super IO Chip

OS Select



Serial Port 1 Confi guration

Serial Port 2 Confi guration

Serial Port 3 Confi guration

NCT6106D

[Windows]





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

OS Select

Select the OS support: Windows or Linux/DOS.

Serial Port 1 Configuration to Serial Port 3 Configuration

Set the parameters of serial port 1 (COM A) to serial port 3 (COM C).

Advanced

Serial Port 1 Confi guration

Serial Port

Device Settings

Change Settings

RS485 Auto Flow

[Enabled]

IO=3F8h; IRQ=4;

[Auto]

[Disabled]

Enable or Disable Serial

Port (COM)





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Advanced

Serial Port 2 Confi guration

Serial Port

Device Settings

Change Settings

RS485 Auto Flow

[Enabled]

IO=2F8h; IRQ=3;

[Auto]

[Disabled]

Enable or Disable Serial

Port (COM)





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Advanced

Serial Port 3 Confi guration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3E8h; IRQ=11;

[Auto]

Enable or Disable Serial

Port (COM)





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3

Serial Port

Enables or disables the serial COM port.

Change Settings

Selects the IO/IRQ settings for the super I/O device.

RS485 Auto Flow

Sets the RS485 auto flow of the serial COM port.

Chapter 3 BIOS Setup

NCT6106D HW Monitor

This section displays the hardware health monitor.

Advanced

PC Health Status

Smart Fan Function

SYS Thermistor Temp

CPU (PECI) Temp

CPUFan Speed

SysFan 1 Speed

SysFan 2 Speed

VCORE

VIN0 (5V)

VIN1 (12V)

VIN2 (DRAM)

VBAT

[Disabled]

: +44.0 C

: +86.5 C

: N/A

: 7297 RPM

: +1.744 V

: +5.096 V

: +12.144 V

: +1.344 V

: +3.280 V

Enable or Disable Smart

Fan





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Smart Fan Function

Enables or Disables the Smart Fan.

Advanced

Smart Fan Function

Enable CPU Smart Fan

CPU Smart Fan Control

Boundary 4

Boundary 3

Boundary 2

Boundary 1

Speed Count 5

Speed Count 4

Speed Count 3

Speed Count 2

Speed Count 1

[Enabled]

100

System Smart Fan (1) Control

Boundary 4

Boundary 3

Boundary 2

Boundary 1

Speed Count 5

Speed Count 4

Speed Count 3

Speed Count 2

Speed Count 1

[Enabled]

100





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Reset

ESC: Exit

System Smart Fan (2) Control

Boundary 4

Boundary 3

Boundary 2

Boundary 1

Speed Count 5

Speed Count 4

Speed Count 3

Speed Count 2

Speed Count 1

[Enabled]

100

Chapter 3 BIOS Setup

Chapter 3

CPU Smart Fan Control

When this feature is set to Automatic, the CPU’s fan speed will rotate according to the

CPU’s temperature. The higher the temperature, the faster the speed of rotation.

System Smart Fan Control

When this feature is set to Automatic, the System’s fan speed will rotate according to the System’s temperature. The higher the temperature, the faster the speed of rotation.

Boundary 1 to Boundary 4

The range is 0-127.

Speed Count 1 to Speed Count 5

The range is 1-100%.

Aux Fan Mode

Selects the Aux fan’s mode. The options are Thermal CruiseTM Mode, Fan Speed

CruiseTM Mode and SmartFan TM IV Mode.

AuxFan Target Temp

This field is used to enter the target value of the Aux fan’s temperature.

AuxFan Tolerance

This field is used to enter the tolerance value of the Aux fan’s temperature.

Chapter 3

Power Failure Control

This section configures the status control when the power failure occurs.

Advanced

Power Failure Control

Power-Loss State [Keep Last State]

Control the status when power loss occurs





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Power-Loss State

Controls the status when the power loss occurs.

Always Off

When power returns after an AC power failure, the system’s power is off. You press the Power button to power-on the system.

must

Always On

When power returns after an AC power failure, the system will automatically power-on.

Keep Last State

When power returns after an AC power failure, the system will return to the state where you left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will remain off when power returns. If the system’s power is on when AC power failure occurs, the system will power-on when power returns.

Chapter 3 BIOS Setup

WatchDog Configuration

This section sets the system watchdog parameters.

Advanced

WatchDog Parameters

WatchDog Count Mode

WatchDog TimeOut Value

[Second]

WatchDog Count Mode

Selection

Chapter 3

Network Stack

This section is used to enable or disable UEFI network stack.

Network Stack

Advanced

[Disabled] Enable/Disable UEFI network stack.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

WatchDog Count Mode

Selects the watchdog count mode.

WatchDog TimeOut Value

Enters the watchdog timeout value. 0 means disabled.





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

When Network Stack is enabled, it will display the following information:

Advanced

Network Stack

Ipv4 PXE Support

Ipv6 PXE Support

[Enabled]

Enable/Disable UEFI network stack.





Enter:

+/-:

F1:

F2:

Select Screen

Select Item

Select

Change Opt.

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Chapter 3

Ipv4 PXE Support

When enabled, Ipv4 PXE boot supports. When disabled, Ipv4 PXE boot option will not be created.

Ipv6 PXE Support

When enabled, Ipv6 PXE boot supports. When disabled, Ipv6 PXE boot option will not be created.

Intel(R) Ethernet Connection I218-LM - 88:88:88:88:87:88...

This section is used to configure the parameters of the Gigabit Ethernet device.

Advanced

PORT CONFIGURATION MENU

 NIC Confi guration

Blink LEDs 0

Confi gure Boot Protocol,

Wake on LAN, Link

Speed, and VLAN.

PORT CONFIGURATION INFORMATION

UEFI Driver:

Adapter PBA:

Chip Type:

PCI Device ID

Bus: Device: Function:

Link Status

MAC Address:

Intel(R) PRO/1000 5.5.19

FFFFFF-OFF

Intel PCH LPT

155A

00:19:00

[Disconnected]

88:88:88:88:87:88





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Blink LEDs

Identifies the physical network port by blinking the associated LED.

Link Status

This field indicates the link status of the network device.

Chapter 3 BIOS Setup

NIC Configuration

This field is used to configure the Boot Protocol, Wake on LAN, Link Speed and VLAN.

Link Speed

Wake on LAN

Advanced

[Auto Negotiaed]

[Enabled]

Specifi es the port speed used for the selected boot protocol





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Link Speed

This field is used to specify the port speed used for the selected boot protocol.

Wake on LAN

Enables the server to be powered on using an in-band magic packet.

Chapter 3

Intel(R) I210 Gigabit Network Connection - 00:01:29:50...

This section is used to configure the parameters of the Gigabit Ethernet device.

Advanced

Confi gure Boot Protocol,

Wake on LAN, Link

Speed, and VLAN.

PORT CONFIGURATION MENU



NIC Confi guration

Blink LEDs 0

PORT CONFIGURATION INFORMATION

UEFI Driver:

Adapter PBA:

Chip Type:

PCI Device ID

Bus: Device: Function:

Link Status

MAC Address:

Virtual MAC Address

Intel(R) PRO/1000 5.5.19

001300-000

Intel i210

1533

02:00:00

[Disconnected]

00:01:29:50:49:6D





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3:

F4: Save & Exit

ESC:

Optimized Defaults

Exit

Blink LEDs

Identifies the physical network port by blinking the associated LED.

Link Status

This field indicates the link status of the network device.

Virtual MAC Address

Programmatically assignable MAC address of the Ethernet port.

Chapter 3 BIOS Setup

NIC Configuration

This field is used to configure the Boot Protocol, Wake on LAN, Link Speed and VLAN.

Link Speed

Wake on LAN

Advanced

[Auto Negotiaed]

[Enabled]

Specifi es the port speed used for the selected boot protocol

Chapter 3

Chipset

This section configures relevant chipset functions.

Main

Advanced Chipset Boot Security Save & Exit

PCH Parameters

 PCH-IO Confi guration

 System Agent (SA) Confi guration





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Link Speed

This field is used to specify the port speed used for the selected boot protocol.

Wake on LAN

Enables the server to be powered on using an in-band magic packet.





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Chapter 3

PCH-IO Configuration

This section illustrates the PCH parameters.

Chipset

Intel PCH RC Version

Intel PCH SKU Name

Intel PCH Rev ID

 PCI Express Confi guration

 USB Confi guration

Wake on LAN

1.7.0.0

Premium SKU

04/B2

[Enabled]

PCI Express Confi guration settings.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Wake on LAN

Enables or disables the integrated LAN controller to wake the system. (The Wake on

LAN cannot be disabled if ME is set to On at the Sx state.)

PCI Express Configuration

This field is used to configure the PCI Express settings.

Chipset

PCI Express Confi guration

 PCI Express Root Port

PCI Express Root Port

Settings.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

PCI Express Root Port

Chipset

PCI Express Root Port 5

ASPM Support

PME SCI

Hot Plug

PCIe Speed

[Enabled]

[Disabled]

[Enabled]

[Disabled]

[Auto]

Control the PCI Express

Root port.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

ASPM Support

Sets the ASPM support.

Force L0s Force all links to the L0s state

Auto BIOS auto configure

Disabled Disable the ASPM support

PME SCI

Enables or disables the PCI Express PME SCI.

Hot Plug

Enables or disables the PCI Express Hot Plug.

PCIe Speed

Selects the PCI Express port speed.

Chapter 3

USB Configuration

This field is used to configure the USB settings.

Chipset

USB Confi guration

XHCI Mode

[Smart Auto]

Mode of operation of

XHCI controller.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

XHCI Mode

Selects the operation mode of the XHCI controller. The options are Smart Auto, Auto, Enabled, Disabled and Manual.

Chapter 3 BIOS Setup

System Agent (SA) Configuration

This section is used to configure the parameters of System Agent.

Chipset

System Agent Bridge Name

System Agent RC Version

VT-d Capability

Haswell

1.7.0.0

Supported

[Enabled]

Check to enable VT-d function on MCH.

VT-d

 Graphics Confi guration

 Memory Confi guration





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

VT-d

Enables the VT-d function on MCH.

Chapter 3

Graphics Configuration

This field configures the graphics settings.

Graphics Confi guration

IGFX VBIOS Version

IGfx Frequency

Primary Display

Internal Graphics

DVMT Pre-Allocated

 LCD Control

Chipset

2179

400 MHz

[Auto]

[32M]

Select which of IGFX/

PEG/PCI Graphics device should be Primary Display or Select SG for switchable Gfx.





Enter:

+/-:

Select Screen

Select Item

Select

Change Opt.

F1:

F2:

General Help

Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Primary Display

Auto When the system boots, it will auto detects the display device.

IGFX When the system boots, it will first initialize the onboard VGA.

PCIE When the system boots, it will first initialize the PCI Express x1 graphics card.

Internal Graphics

Keeps IGD enabled based on the setup options

Chapter 3 BIOS Setup

DVMT Pre-Allocated

Selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal

Graphics Device. Please refer to the information shown below.

Graphics Confi guration

IGFX VBIOS Version

IGfx Frequency

Primary Display

Internal Graphics

DVMT Pre-Allocated

 LCD Control

Chipset

2179

400 MHz

DVMT Pre-Allocated

32M

64M

96M

128M

160M

192M

224M

256M

288M

320M

352M

384M

416M

448M

480M

512M

1024M

Select DVMT5.0 Pre-

Allocated (Fixed) Graphics Memory size used by the Internal Graphics

Device.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3

LCD Control

This field configures the LCD control.

LCD Control

Primary IGFX Boot Display

Secondary IGFX Boot Display

LCD Panel Type

Active LVDS

Chipset

[HDMI1]

[Disabled]

[Type 4 1280x1024......]

[Enabled]

Select the Video Device which will be activated during POST. This has no effect if external graphics present.

Secondary boot display selection will appear based on your selection.

VGA modes will be supported only on primary display.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Secondary IGFX Boot Display

Selects the secondary display device.

LCD Panel Type

Selects the LCD panel used by the Internal Graphics Device via selecting the appropriate setup item.

LCD Control

Primary IGFX Boot Display

Secondary IGFX Boot Display

LCD Panel Type

Active LVDS

Chipset

[HDMI1]

Select LCD panel used by

Internal Graphics Device by selecting the appropriate setup item.

LCD Panel Type

VBIOS Default

Type 1

640x480

Type 2

800x600

Type 3

1024x768

Type 4

1280x1024

Type 5

1400x1050 (108MHz)

Type 6

1400x1050 (122MHz)

Type 7

1600x1200

Type 8

1366x768

Type 9

1680x1050

Type 10

1920x1200

Type 11

1440x900

Type 12

1600x900

Type 13

1024x768

Type 14

1280x800

Type 15

1920x1080

Type 16

2048x1536





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Active LVDS

Enables or disables the LVDS function.

Chapter 3

Memory Configuration

This field only displays the memory configuration.

Chipset

Memory Information

Memory RC Version

Memory Frequency

Total Memory

Memory Voltage

DIMM#1

DIMM#2

CAS Latency (tCL)

Minimum delay time

CAS to RAS (tRCDmin)

Row Precharge (tRPmin)

Active to Precharge (tRASmin)



1.7.0.0

1600 Mhz

12288 MB (DDR3)

1.35V

8192 MB (DDR3)

4096 MB (DDR3)





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Chapter 3 BIOS Setup

Chapter 3

Boot

Main

Boot Confi guration

Setup Prompt Timeout

Bootup NumLock State

Quiet Boot

Fast Boot

Advanced

Chipset Boot Security Save & Exit

[On]

[Disabled]

Number of seconds to wait for setup activation key.

65535(0xFFFF) means indefi nite waiting.

Boot Option Priorities

Boot Option #1

Boot Option #2

Hard Drive BBS Priorities

 CSM Parameters

[P1: ST160LT007-9ZV1...]

[UEFI: TOSHIBA Trans...]





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Setup Prompt Timeout

Selects the number of seconds to wait for the setup activation key. 65535(0xFFFF) denotes indefinite waiting.

Bootup NumLock State

This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.

Quiet Boot

Enables or disables the quiet boot function.

Fast Boot

Enables or disables the boot with the initialization of a minimal set of devices required to launch the active boot option. Has no effect on BBS boot options.

Boot Option #1/#2

Sets the system boot order.

Hard Drive BBS Priorities

Sets the order of the legacy devices in this group.

CSM Parameters

Launch CSM

Boot option fi lter

Boot

Launch PXE OpROM policy

Launch Storage OpROM policy

Launch Video OpROM policy

Other PCI device ROM priority

[Enabled]

[UEFI and Legacy]

[Do not launch]

[Legacy only]

[UEFI OpROM]

This option controls if

CSM will be launched.





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Launch CSM

This option controls if CSM will be launched.

Boot option filter

This option controls what devices system can boot to.

Launch PXE OpROM policy

Controls the execution of UEFI and legacy PXE OpROM.

Launch Storage OpROM policy

Controls the execution of UEFI and legacy storage OpROM.

Launch Video OpROM policy

Controls the execution of UEFI and legacy video OpROM.

Other PCI device ROM priority

For PCI devices other than Network. Mass storage or Video defines which OpROM to launch.

Chapter 3 BIOS Setup

Security

Main

Advanced

Password Description

Chipset Boot Security Save & Exit

Set Administrator

Password.

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have

Administrator rights.

The password length must be in the following range:

Minimum length 3

Maximum length 20

Administrator Password

User Password





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Administrator Password

Sets the administrator password.

User Password

Sets the user password.

Chapter 3

Save & Exit

Main

Advanced

Chipset Boot Security Save & Exit

Save Changes and Exit

Discard Changes and Exit

Save Changes and Reset

Discard Changes and Reset

Exit system setup after saving the changes

Save Options

Save Changes

Discard Changes

Restore Defaults

Save as User Defaults

Restore as User Defaults

Boot Override

P1: ST160LT007-9ZV14D

UEFI: TOSHIBA TransMemory 1.00

Launch EFI Shell from fi lesystem device





Select Screen

Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F4: Save & Exit

ESC: Exit

Save Changes and Exit

Exits the system setup after saving the changes.

Discard Changes and Exit

Exits the system setup without saving any changes.

Save Changes and Reset

To save the changes, select this field and then press <Enter>. A dialog box will appear. Select Yes to reset the system after saving all changes made.

Discard Changes and Reset

To discard the changes, select this field and then press <Enter>. A dialog box will appear. Select Yes to reset the system setup without saving any changes.

Save Changes

Saves changes done so far to any of the setup options.

Discard Changes

Discards changes done so far to any of the setup options.

Restore Defaults

To restore and load the optimized default values, select this field and then press

<Enter>. A dialog box will appear. Select Yes to restore the default values of all the setup options.

Chapter 3 BIOS Setup

Hello! I'm familiar with the DFI HU101/HU103 Mini-ITX Industrial Motherboard user manual. I can help you with questions about specifications, hardware installation (memory, connectors, expansion slots), BIOS setup (including Intel AMT configuration), supported software, digital I/O programming, RAID configurations, troubleshooting, and included utilities. The manual provides detailed diagrams and step-by-step instructions.

Show related prompts