advertisement
WVRC-4 Installation and Operation Manual
INTRODUCTION
Thank you for your purchase of a Broadcast Tools® WVRC-4, Four Channel
WEB and Voice Dial-up Remote Control System (referred to as the WVRC-4 throughout this manual). We’re confident that this product should give you many years of dependable service. This manual is intended to give you all the information needed to install and operate the Broadcast Tools® WVRC-4.
SAFETY INFORMATION
Only qualified technical personnel should install the WVRC-4. Any attempt to install this device by a person who is not technically qualified could result in a hazardous condition to the installer or other personnel, and/or damage to the WVRC-4 or other equipment. Broadcast transmitters can operate at voltages that are potentially lethal. Please ensure that proper safety precautions have been made before installing this device. If you are unfamiliar with this type of equipment, please contact a properly qualified engineer to handle the installation and setup of the WVRC-4.
For additional safety, it is strongly recommended that, in addition to setting the WVRC-4 in to OP/PGM mode, the remote/local switch on any transmitter or high voltage equipment also be set to local mode.
While the WVRC-4’s relays are physically capable of handling 250 VAC, this practice is extremely dangerous and should never be attempted. The pluggable euroblock screw terminals are not designed to shield humans from potentially dangerous voltages. Contact with high voltages can cause serious injury or death. The maximum recommended voltage for the WVRC-4 is 30V. Switching of high voltages should only be done external from the WVRC-4 and in a manner that isolates the voltages from accidental contact with humans.
WHO TO CONTACT FOR HELP
If you have any questions regarding your product or you need assistance, please contact your distributor from whom you purchased this equipment.
If you would like more information about Broadcast Tools® products, you may reach us at:
Broadcast Tools, Inc.
131 State Street
Sedro-Woolley, WA 98284-1540 USA
Voice: 360.854.9559
Fax: 866.783.1742
Internet Home Page: www.broadcasttools.com
E-mail: [email protected]
CAUTION!
Broadcast Tools®
Products, as with any electronic device, can fail without warning.
Do not use this product in applications where a life threatening condition could result due to failure. Serious injury or death can occur if a command channel is activated while you are performing maintenance on your equipment. If you are performing maintenance on your equipment, you should press the
“OP/PGM” button on the front panel of your
WVRC-4 forcing the unit in to local mode.
The “PGM” LED will illuminate. Local mode prevents the unit from performing relay commands.
THANK YOU FOR CHOOSING
BROADCAST TOOLS® BRAND PRODUCTS!
Broadcast Tools is a Veteran Owned Business
NOTE:
This manual should be read thoroughly before installation and operation.
Designed, Assembled and Supported in WA State, USA
e-mail:
voice:
360.854.9559
fax:
866.783.1742
INTRODUCTION
3
advertisement
Related manuals
advertisement
Table of contents
- 3 Introduction
- 3 Safety Information
- 4 Who to Contact for Help
- 4 Product Overview
- 5 Inspection
- 5 Installation
- 10 Dial-up Programming
- 10 Installing Factory Defaults
- 11 Program Menu
- 12 Menu Navigator
- 12 Dial Out Numbers
- 13 Dial Out List
- 13 Settings
- 14 Access Code
- 14 Repeat
- 14 Silence Sensor
- 14 Power Fail
- 14 Monitor Access Code
- 14 Analog Debounce Timer
- 15 Pager Numbers and Data Strings
- 15 Analog (metering) Setup
- 17 Status Setup
- 18 Recording Voice Prompts
- 18 Configure DIP Switch Settings
- 21 Dial-up Operation
- 22 WEB and Dial-Up Notice
- 23 Web Setup
- 23 Configuration Info
- 25 Ethernet Setup
- 26 Firmware
- 26 Java Applet
- 27 Main Screen
- 28 Login Dialog
- 28 User Setup Dialog
- 29 System Setup Dialog
- 30 Network Setup Dialog
- 31 Schedule Setup Dialog
- 32 Schedule Detail Dialog
- 33 Analog (metering) Setup Dialog
- 33 Status/Relay Setup Dialog
- 34 Virtual Channel Setup Dialog
- 35 About Dialog
- 36 Specifications
- 37 Warranty
- 38 Declaration of Conformity