advertisement
4.17
W1900 Series Clothes Washers
4.16
Technical Information
Imbalance Monitoring
Range 1
Range 2
0-0.7 kg
0.7-1.1 kg
No reduction in spin speed.
If imbalance exists after 3 attempts to redistribute the load then the spin speed is limited to 2 nd highest value (exact rpm varies by model number)
Range 3 1.1-2.0 kg
If imbalance exists after 3 attempts to redistribute the load then the spin speed is limited to 3 rd highest value (exact rpm varies by model number)
Range 4 > 2 kg
Load distribution attempts continually made until imbalance is reduced or the program time has completed.
Table 4-2: Imbalance Monitoring
Motor Circuit
A Change Field Relay (spin/ wash actuation)
B Motor Direction Relay
C Temperature Limiter
D Field Windings
E Rotor Windings
F Tachogenerator
Figure 4-7: Motor Circuit
33
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Appliance Overview
- 7 Overview of Controls
- 11 Technical Data
- 13 Dispenser Assembly
- 15 Layout of Electrical Components W1903, W1918, W1926 & W
- 16 Layout of Electrical Components W1966 & W
- 17 Electrical Requirements
- 18 Plumbing Requirements
- 19 Installation Procedure
- 23 General Operation
- 23 Additional Function Pushbuttons
- 25 Casing Assembly
- 25 Electro-Mechanical Door Lock
- 26 Miele Eco Wash System
- 27 Drum Suspension
- 28 Heating Circuit Information
- 29 Water Level Switch
- 29 Water Control System – Intake
- 30 Water Control System – Rinses
- 30 Inlet Hose(s) Filters
- 30 4.10 Inlet Valves
- 30 4.11 Dispenser Assembly
- 31 4.12 Non-Return Valve & Drain Venting
- 32 4.13 Main Motor
- 32 4.14 Motor Speed Control
- 32 4.15 Tachogenerator
- 33 4.16 Imbalance Monitoring
- 33 4.17 Motor Circuit
- 34 4.18 Program Control
- 34 Heater Relays
- 35 Dispenser Drawer – Removal
- 36 Appliance Lid – Removal
- 36 Front Service Panel – Access
- 37 Door Seal – Replacement
- 38 Air Trap – Replacement
- 39 Heater Element(s) – Replacement
- 39 Inlet Valve – Replacement
- 40 Manual Draining and Filter Removal
- 41 Drain Pump - Replacement
- 42 5.10 Main Motor – Carbon Brush Replacement
- 43 5.11 Control Electronic – Removal
- 44 5.12 Power Supply Electronic - Removal
- 45 Procedure)
- 47 5.14 Water Level Switch - Replacement
- 48 5.15 Heater Relays - Access
- 49 Service Mode - W1903, W1918, W1926 & W
- 50 Service Mode - W1966 and W
- 51 Fault Codes
- 52 Fault Code – Definitions (W1966 & W1986 Only)
- 54 Programming Mode
- 57 Description of Programmable Options
- 61 Special Features
- 61 6.6.1 Electronic Program Lock
- 61 6.6.2 Child Safety Lock
- 62 6.6.3 Demonstration Mode
- 63 Fault Indicators
- 67 Porthole Door is locked / unable to access service door
- 67 Customer reports water leaks from front left side of the appliance
- 67 Replacement