advertisement
Temperature:
Humidity:
Shock:
Vibration:
Operation:
Storage:
40°F to 95°F (ST to 35°C)
-22°F to 140°F (-30°C to 60°C)
Operation:
10% to 80% condensation)
Storage:
5% to
85%
(without
(without condensation)
Operation: Up to
Storage: Up to
1
G within
1 ms
2
G within
1 ms
Operation: Up to
0.25
G at up to
55 Hz
Storage: Up to 0.50 G at up to 55 Hz
Double-Bin Cut Sheet Feeder (Optional)
Dimensions and weight:
26.7”(W) X 22.9”(D) x 16.5”(H)
(mounted on the printer) approx.
13.2 lbs.
Bin capacity: bin
1
Single sheets: Up to
150 sheets of
22 lb. paper
Up to
185 sheets of
17 exceed 0.59” or 15mm) lb. paper
(Total thickness should not
Envelopes* : Up to
25
(plain and bond type)
Up to 30 (air mail) bin 2
Single sheets: Up to
150
Up to
185 sheets of sheets of
(Total thickness should not exceed
22
17 lb. paper lb. paper
0.59” or
15mm)
* Envelopes can only be used in bin
1.
A-6 Technical Specifications
Stacker capacity:
Face down
Face up
Single sheets:
Envelopes:
Single sheets:
Envelopes:
Up to
60 sheets of
22 lb.
paper
Up to 75 sheets of
17 lb.
paper
Up to
10
(plain and bond type)
Up to
12
(air mail)
Up to
150 sheets of
22 lb.
paper
Up to
185
sheets of
17 lb.
paper
Up to
25
(plain and bond type)
Up to
30
(air mail)
Reliability
MCBF (Mean Cycle Between Failure):
100,000 cycles
Environmental conditions
Temperature: Operation:
Humidity:
Storage:
Operation:
Storage:
+41"F(+5"C) to +95”F
(+35"(z)
-22"F(-30°C) to
+158"F
(+7o"c)
15% to 80% without condensation
5% to 90% without condensation
Technical Specifications
A-7
Paper
Width
Length
Thickness
Weight:
Printable area:
Single sheet bin 1 and bin 2
7.17” to 14.3”
(182mm to 364mm)
8.27” to 14.3”
(210mm to 364mm)
0.0028” to 0.0039”
(0.07mm to O.lmm)
17 to 22 lb. paper
3 mm
(0.12”)
)r more
8.5 mm (0.33”) or more or more
13.5 mm /0.53”J or more
It
3 mm
(0.12”!
or more envelope bin 1
6.50” to 9.49”
(166mm to 241mm)
3.62” to 4.09”
(92mm to 104mm)
0.0063” to 0.0205”
(0.16mm to 0.52mm)
12 to 24 lb. paper
T or more
I , 2 2 m m
1
(0.87”) or more
A-8 Technical Specifications
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 FRONT MATTER
- 4 TABLE OF CONTENTS
- 6 INTRODUCTION
- 6 Features
- 7 Options
- 8 About This Guide
- 9 Where to Get Help
- 10 CHAP 1-SETTING UP THE PRINTER
- 11 Unpacking the Printer
- 11 Removing the Protective Materials
- 15 Choosing a Place for the Printer
- 16 Assembling the Printer
- 16 Installing the Platen Knob
- 18 Installing the Ribbon Cartridge
- 21 Attaching the Paper Guide
- 24 Testing the Printer
- 24 Connecting to a Power Supply
- 25 Running the Self Test
- 31 Connecting the Printer to Your Computer
- 31 The Parallel Interface
- 33 The Serial Interface
- 36 Setting Up Your Application Software
- 37 Choosing from a Menu
- 38 CHAP 2-PAPER HANDLING
- 39 Using Single Sheets
- 39 Loading a Sheet
- 42 Reloading During Printing
- 42 Using Continuous Paper
- 42 Positioning your Continuous Paper Supply
- 43 Loading Continuous Paper
- 50 When You Have Finished Printing
- 51 Reversing the Paper to the Standby Position
- 53 Switching Between Continuous and Single Sheets
- 53 Switching to Single Sheets
- 56 Switching Back to Continuous Paper
- 59 Printing on Special Paper
- 59 Multi-Part Forms
- 60 Labels
- 63 Envelopes
- 65 CHAP 3-USING THE PRINTER
- 66 Operating the Control Panel
- 66 The Display
- 67 The Lights
- 68 The Buttons
- 72 Other Control Panel Features
- 72 SelecType Settings
- 74 Using SelecType
- 76 Selecting a Main Menu Mode
- 77 LOAD MACRO
- 79 CHANGE MACRO
- 82 CHANGE DEFAULTS
- 87 PRINT OUT SETTINGS
- 88 CLEAR OUT MACROS
- 90 Page Length
- 92 Skip Over Perforation
- 94 Setting the Loading Position
- 94 Adjusting the Loading Position
- 95 Short Tear-Off
- 97 Selecting Typestyles
- 98 Fonts
- 101 Pitch
- 102 Condensed Mode
- 103 Choosing an International Character Set
- 104 Choosing a Character Table
- 106 CHAP 4-USING SOFTWARE AND GRAPHICS
- 107 Using the LQ-2550 With Application Programs
- 107 Using Printer Selection Menus
- 107 A Quick Test
- 108 Using Word Processors
- 108 Using Spreadsheets
- 109 Using Graphics Software
- 110 Computer-Printer Communication
- 111 Escape Sequences
- 111 Printer Commands
- 112 Using the Command Summary
- 112 Sending Printer Commands from Within Your Software Program
- 112 Enhancing Your Printing
- 113 Character Size
- 113 Special Effects and Emphasis
- 116 Selecting Typestyles with Master Select
- 118 Graphics
- 118 The Print Head
- 119 Dot Pattern
- 119 Color Graphics
- 120 Twenty-Four-Pin Graphics
- 120 Pin Labels
- 121 The Graphics Command
- 122 Column Reservation Numbers
- 123 A Simple Graphics Program
- 123 Using Hand-Calculated
- 127 Individual Graphics Option Commands
- 127 The Reassigning Command
- 128 User-Defined Characters
- 128 Designing Your Characters
- 129 Design Grids
- 131 Data Numbers
- 132 Sending Information to Your Printer
- 134 Printing User-Defined Characters
- 135 Copying ROM Characters to RAM
- 135 Letter Quality Characters
- 136 Proportional Mode Characters
- 136 Superscripts and Subscripts
- 121 The Graphics Command
- 122 Column Reservation Numbers
- 123 A simple Graphics Program
- 123 Using Hand-Calculated Data to Print Graphics
- 123 Using Software and Graphics
- 137 Mixing Print Styles
- 139 CHAP 5-MAINTENANCE AND TRANSPORTATION
- 140 Cleaning the Printer
- 141 Replacing the Ribbon
- 145 Transporting the Printer
- 148 CHAP 6-TROUBLESHOOTING
- 149 Troubleshooting
- 149 Problems and Solutions
- 149 The Printer Does Not Print
- 149 The Printer Stops Printing
- 150 The Printout is Spaced Incorrectly
- 150 The Printout is Faint or Uneven
- 151 The Printout is Not what You Expect
- 151 Single Sheets Do Not Feed Properly
- 151 Continuous Paper Does Not Feed Properly
- 152 Cut Sheet Feeder Does Not Load Paper Correctly
- 152 The Short Tear-Off Feature Does Not Work Properly
- 152 Color Printing Is Not What You Expect
- 153 Data Dump Mode
- 154 CHAP 7-USING PRINTER OPTIONS
- 155 The Cut Sheet Feeder
- 155 Installation
- 159 Loading Paper
- 162 Testing the Printer In The Cut Sheet Feeder Mode
- 164 Loading Envelopes
- 166 Using the Cut Sheet Feeder
- 170 Switching between the Cut Sheet Feeder and Continuous Paper
- 171 Loading Single Sheets
- 173 Removing The Cut Sheet Feeder
- 174 The Pull Tractor
- 174 Installation
- 177 Loading Paper
- 184 Removing the Pull Tractor
- 186 Interface Boards
- 186 Choosing an Interface
- 186 Compatible Interfaces
- 187 Installing the Interface Board
- 198 The Multi-Font Module
- 198 Installation
- 200 Selecting a Font
- 201 CHAP 8-COMMAND SUMMARY
- 205 Commands in Numerical Order
- 208 Commands Arranged by Topic
- 208 Printer Operation
- 211 MSB Control
- 212 Data Control
- 213 Vertical Motion
- 218 Horizontal Motion
- 221 Overall Printing Style
- 223 Print Size and Character Width
- 227 Print Enhancement
- 230 Word Processing
- 231 Character Tables
- 232 User Defined Characters
- 234 Graphics
- 237 APPENDIX A-TECHNICAL SPECIFICATIONS
- 238 Printer Specifications
- 242 Double-Bin Cut Sheet Feeder (Optional)
- 245 Interface Specifications
- 249 Initialization
- 250 Default Settings
- 259 GLOSSARY
- 265 INDEX