advertisement
54 The Test Button AXIS 1650 User’s Manual
Section 5 The Test Button
The test button is located on the front right hand side of the print server and is used to perform a Factory Default:
1. Remove the external power supply to switch off the print server.
2. Press and hold down the test button, while you reconnect the external power supply.
3. Continue to hold down the test button until the network indicator remains constantly lit. This should take about 20 seconds.
4. Restart the print server by disconnecting and reconnecting the external power supply.
Important:
• A factory default will reset all print server parameters and settings to their default values except Node address (NODE_ADDR.)
• The IP address (INT_ADDR.) will be reset to default 192.168.0.90
If the AXIS 1650 is connected to a BubbleJet printer, the test button can be used for the following operations:
• Print a Test Page
Press the test button once to print a test page. The test page contains basic information about the print server. It is recommended that you print a test page every time you connect the print server to a printer
• Perform a Factory Default
See description above.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Safety Notices
- 2 Electromagnetic Compatibility (EMC)
- 3 Liability
- 3 Axis’ Trademarks
- 3 Other Trademark Acknowledgments
- 3 Patent information
- 4 Table of Contents
- 5 Preface
- 5 About this Manual
- 5 About Axis
- 6 Support Services
- 7 Section 1 Product Overview
- 7 Package Contents
- 8 Supported Printers
- 8 Supported Environments
- 9 Installation and Integration
- 9 Configuration and Management
- 9 Printing Protocol
- 11 Section 2 Print Server Installation
- 11 1. Connect the Hardware
- 13 2. Set the IP Address
- 14 Set a Static IP Address using AXIS IP JumpStarter
- 16 Set a Static IP Address using ARP in Windows 98/Me/2000/XP/2003
- 17 Set a Static IP Address using ARP in UNIX
- 18 Set an IP Address with NetSpot Device Installer software
- 21 IP Address Host Names
- 22 Section 3 Windows Installation
- 22 Installing Printer Ports using AXIS CAPT Print Monitor
- 23 Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003
- 29 Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me
- 32 Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003
- 35 Section 4 Print Server Management and Configuration
- 35 Configuration Overview
- 36 Print Server Management from the Embedded Web Pages
- 37 Accessing the Embedded Web Pages
- 38 Available Services from the User Mode
- 38 Print Server Name
- 38 System Location
- 39 Serial Number
- 39 Language
- 40 Available Services from the Admin Mode
- 40 Print Server Name
- 40 System Name
- 41 System Location
- 41 System Contact:
- 41 System Contact Phone Nbr.:
- 41 System Comment:
- 41 Language:
- 41 Root Password:
- 41 SNMP Enabled:
- 42 Community Name:
- 42 TCP Restriction Enabled
- 42 TCP Restriction Mode
- 42 TCP Restriction IP Address List:
- 42 SNMP Restriction Enabled:
- 43 SNMP Restriction Mode:
- 43 SNMP Restriction IP Address List:
- 43 SLP Restriction Enabled
- 43 SLP Restriction Mode
- 43 SLP Restriction IP Address List
- 44 Serial Number
- 44 Parameter List
- 44 Restart
- 44 Software Default
- 45 Frame Type
- 45 LPD Banner Page Mode*
- 46 DHCP Enabled
- 46 BOOTP Enabled
- 46 RARP Enabled
- 46 IP Address
- 47 Subnet Mask
- 47 Default Router
- 47 DNS Server Address
- 47 DNS Dynamic Update
- 47 DNS Host name
- 47 DNS Domain Name
- 48 WINS Enabled
- 48 WINS Server Address
- 48 WINS Host Name
- 48 Scope ID
- 48 SLP enabled
- 48 SLP scope list
- 48 SNTP Server Address
- 49 SNTP update interval
- 49 Time Zone (Only visible in English firmware version)
- 49 Daylight Saving (Only visible in English firmware version)
- 49 Troubleshoot and Upgrade
- 49 Server Report
- 51 Print Server Management Using FTP
- 51 Editing the config file
- 52 FTP Help
- 53 Print Server Management Using SNMP
- 54 Section 5 The Test Button
- 55 Section 6 Upgrading the Firmware
- 56 Upgrading using FTP
- 65 Technical Specifications
- 65 Supported Printers
- 65 Supported Systems
- 65 Supported Protocols
- 65 Network Management
- 66 Supported Languages
- 66 Logical Connection
- 66 Wired Network Attachments
- 66 Printer Ports
- 66 Power Consumption
- 66 Dimensions
- 67 Environmental
- 67 Approvals
- 67 Safety
- 67 Hardware
- 67 Front Panel
- 58 Appendix A Enabling Unicast Network Communication
- 62 Appendix B Internet Connection Firewall in Windows XP SP2
- 68 Index