- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- AMX
- NXC-ME260
- Instruction manual
SPE cable pinout information. AMX NetLinx Master-Ethernet Card/Module NXC-ME260, NXC-ME260
Add to My manuals48 Pages
advertisement
![SPE cable pinout information. AMX NetLinx Master-Ethernet Card/Module NXC-ME260, NXC-ME260 | Manualzz SPE cable pinout information. AMX NetLinx Master-Ethernet Card/Module NXC-ME260, NXC-ME260 | Manualzz](http://s1.manualzz.com/store/data/000994200_3-6794f2207f6aa50d46df8762acfcd9ec-360x466.png)
Installation and Wiring
NXC-ME260
Master-Ethernet
12VDC
PWR
EXPANSION OUT connector on rear of NXC-ME260
ETHERNET
10/100
SPEED FD
IN
OUT
AXlink PROGRAM ICSNet ICSHub
EXPANSION
1st AXB-SPE (rear panel)
IN OUT
RJ-11 cable (6" max)
EXPANSION
2nd AXB-SPE (rear panel)
OUT
FIG. 6 Daisy chaining two or more AXB-SPE's off of an NXC-ME260
SPE cable pinout information
The following table gives pinout information for the RJ-11 SPE connector. AMX supplies a 6"
RJ-11 cable with the AXB-SPE.
The EXPANSION connectors (on the AXB-SPE) use pins 2, 3, 4 and 5. Pin 2 is Ground; the others are all pin-to-pin connections.
SPE Connector Pinouts and Signals
4
5
6
Pin
1
2
3
Signal no connect
GND
TX
TX enable
RX no connect
Do not use a standard phone extension cable; it will not work with the AXB-SPE.
12 NXC-ME260 NetLinx Master-Ethernet Card/Module
advertisement
Related manuals
advertisement
Table of contents
- 5 Product Information
- 5 Front and rear panel components
- 6 Specifications
- 7 Ethernet ports used by the ME
- 8 Modes and front panel LED blink patterns
- 8 Rear panel LEDs: ICSNet/ICSHub
- 9 Rear panel LEDs: Ethernet
- 11 Installation and Wiring
- 11 Setting the Program Port DIP Switch
- 11 Baud rate settings
- 11 Program Run Disable (PRD) mode
- 12 Setting the Program Port DIP switch
- 12 Program Port Connections/Wiring
- 12 Preparing/connecting captive wires
- 12 DB-9 Program port (front panel)
- 13 5-Pin Program port (rear panel)
- 13 ICSNet RJ-45 Connections/Wiring
- 13 ICSHub RJ-45 Connections/Wiring
- 14 ICSHub IN port
- 14 ICSHub OUT port
- 14 Ethernet 10/100 Base-T RJ-45 Connections/Wiring
- 15 SPE Port Connection/Wiring
- 16 SPE cable pinout information
- 17 Mounting the Modules Into an Equipment Rack
- 17 Mounting the NXC-ME260 in an NXF CardFrame or NXI
- 18 Replacing the Lithium Batteries
- 19 Programming
- 19 Program Port Commands
- 27 ESC Pass Codes
- 28 Notes on Specific Telnet/Terminal Clients
- 28 Windows client programs
- 28 Linux Telnet client
- 29 Firmware Transfers
- 29 Sending Firmware to a NetLinx Device (KIT file)
- 31 NetLinx Security
- 31 NetLinx Security Features
- 31 Security Terms Used in This Document
- 31 Group
- 32 User Name
- 32 Group Name
- 32 Password
- 32 Access Rights
- 32 Directory Associations
- 33 Initial Setup (via Telnet or Terminal Connection)
- 33 Getting connected
- 33 Accessing the Security configuration options
- 34 1) Set system security options for NetLinx Master (Security Options Menu)
- 35 2) Display system security options for NetLinx Master
- 36 3) Add user
- 36 4) Edit User
- 36 Edit User Menu
- 37 Access Rights Menu
- 38 5) Delete user
- 38 6) Show the list of authorized users
- 38 7) Add Group
- 39 Edit Group Menu
- 39 Edit Group Menu: Add directory association
- 40 Edit Group menu: Delete directory association
- 40 Edit Group menu: List directory associations
- 40 Edit Group menu: Change Access Rights
- 41 Edit Group menu: Display Access Rights
- 41 8) Edit Group
- 41 9) Delete Group
- 42 10) Show List of Authorized Groups
- 42 11) Set Telnet Timeout in seconds
- 42 12) Display Telnet Timeout in seconds
- 42 13) Make changes permanent by saving to flash
- 43 Main Security Menu
- 44 Default Security Configuration
- 45 Help menu
- 46 Logging Into a Session
- 47 Logout
- 47 Help Security
- 47 Setup Security