<b>INSTALLATION INFORMATION</b>. Whirlpool Cabrio WTW6400SW, Cabrio WTW8800YW0, Cabrio WTW6600SW, Cabrio WTW6600SB, Cabrio WTW6600SG

DIAGNOSTIC: Automatic

Performs a five-minute automatic test with water functions to check major washer functions

(door can be open). Press the same button used in step 2 to advance through automatic test steps.

NOTE: Basket must be floating in order to agitate. Step C1 must be allowed to complete before advancing to step C5.

Two-Digit

Indicator

C0

C1

C2

C3

C4

Machine Function

Slow spin to 23 rpm.

Warm water fills through

Fresh and Detergent valves, then Fresh valve until basket floats

(disengages); then washer continues filling through Fresh and

Detergent valves to minimum water level.

Cold water fill through

Bleach valve for

10 seconds.

Hot water fill through

Fabric Softener valve for 10 seconds.

NOTE: Step will occur but no water can be dispensed with models that do not have a

fabric softener valve.

Warm water fill through

Detergent valve for

10 seconds.

C5

C6

Recirculate for

10 seconds.

C7

C8

C9

(none)

(Test ends)

Recommended Procedure

If no spin go to Manual: Motor,

Spin.

If no water or fill temperature is wrong, go to Manual: Water

Valves.

If basket does not float or disengage, determine cause of friction.

If no water in bleach cup go to

Manual: Water Valves.

If no water in fabric softener cup go to Manual: Water Valves.

If no water in detergent cup go to Manual: Water Valves.

Drain to basket engaged plus timed drain for

10 seconds.

Drain & slow spin

23 rpm.

Coast to 0 rpm.

End of cycle beep.

If water is not being re-circulated go to Manual: Pumps.

If water is not draining go to

Manual: Pumps.

If basket does not engage determine cause of friction.

If drain pump is not on go to

Manual: Pumps.

If basket is not turning go to

Manual: Motor.

If basket does not stop spinning within 5 seconds, press STOP and restart test.

If no end of cycle beep, make sure cycle signal is on. From Setting

Mode, pressing buttons should sound valid key press beep.

DIAGNOSTIC: Unsuccessful Entry

If entry into diagnostic mode is unsuccessful

(see steps 1 and 2 of Activation of Automatic

Diagnostic Test Mode), refer to the following indications and actions:

6-5

Indication 1: None of the indicators or display turns on.

Action: Press POWER button to enter setting mode.

•

•

If indicators come on, try to change the function for the button used to activate the diagnostic test mode. If that button fails to change the function, something is faulty with the button, and it is not possible to enter the diagnostic mode.

If no indicators come on after pressing

POWER button, go to TEST #1.

Indication 2: Fault code flashes from the display.

Action: Review the Display Fault/Error Codes table for the recommended procedure.

DIAGNOSTIC: Saved Fault Codes

If there are saved fault codes (as indicated in step 3 of Activation of Automatic Diagnostic

Test Mode), the most recent fault code will be displayed and alternately show “F” and “XX” where XX is the fault code, and all the cycle selector indicators flash.

Press and release the same button used to activate Diagnostics

Repeat

Repeat

Repeat

•

•

•

• Second most recent fault code is displayed.

Third most recent fault code is displayed.

Fourth most recent fault code is displayed.

All indicators momentarily turn off, then stay on. After 5 seconds, Automatic test cycle begins.

NOTE: Fault codes are retained.

ACTIVATION OF MANUAL

DIAGNOSTIC TEST MODE

1. Carefully read and perform steps 1 and 2 under Activation of Automatic Diagnostic

Test Mode, and press the same button once during the 5 second display time of the 88.

NOTE: If the button is not pressed within

5 seconds, the Automatic test will start

(after saved fault codes).