HTS Components. Dometic HTS-EC
Add to my manuals
8 Pages
Dometic HTS-EC is a high-quality holding tank system designed to provide reliable and efficient waste management for your boat. Constructed from durable linear low density polyethylene (LLDP) resin, it resists corrosion, odor permeation, and is built to last. The unique diptube design minimizes residual contents while the TankSaver™ vacuum relief valve protects against high vacuum levels. Multiple tank outlets allow for flexible discharge options, and the system is compatible with SeaLand sanitation system components for a complete solution.
advertisement
HTS Components
DTM04 Level Monitor and Micro-Float Switches*
I n c l u d e s f o u r t a n k levels – Empty, Low, Mid and Full. Micro-float switches are installed in holding tank. No electrical components contact waste or water. Operates on 12 or 24-volt DC. Uses only .008 amps at 12 V
DC. Micro-float switches are installed either as a unit (with a 3-inch cap) or as separate indicators.
VacuFlush
Shutdown Relay*
To prevent overfilling a holding tank, a shutdown relay is supplied with HTS-
VG models. When the tank reaches "Full", the relay shuts off the vacuum generator, preventing further flushing of the toilet.
Combined
Float Switches
Separate
Float Switches
VacuFlush ® Vacuum Generators*
On HTS-VG models, VacuFlush vacuum generators combine the vacuum tank and vacuum pump in one unit. All models eliminate hose runs between the vacuum tank and pump of previous VacuFlush systems. HTS vacuum generators feature high-performance vacuum pumps, offering quieter operation and faster vacuum generation than previous models.
Other HTS Features
TankSaver™ Vacuum Relief Valve
Prevents damage due to tank implosion from dockside pumps that generate very high vacuum.
TankSaver valve opens automatically under vacuum, but remains sealed regardless of shockloading or vibrations.
SaniGard™ Holding Tank Vent Filter*
With odor-removing filter media, the vent filter stops odors from escaping the holding tank vent. Keeps boats smelling clean and pleasant. Each cartridge is good for an entire season and is easily replaced.
OdorSafe ® Plus Sanitation Hose
OdorSafe Plus hose provides the best odor barrier of any marine hose available. It delivers up to 19 times greater resistance to sulfurous malodors than other “noodor” marine hoses. On
HTS models, it's used for all 1.5-inch (38mm) hose connections. It's also best for connecting the discharge pump to the through-hull and deck waste fittings.
SaniPump™ Overboard
Discharge Pump*
Runs dry without harm. Draws
6 amps at 12 VDC. Delivers flow rate of 3.9 gallons per minute (14.7 liters per minute). Connects to through-hull fitting. Check Marine
Sanitation Regulations for information on areas where discharge is allowed.
* Not available on all HTS models.
Diptube Discharge
Our diptube discharge design allows for removal of waste from the top of the holding tank rather than near the bottom of the tank. This feature greatly reduces the opportunities for stagnant sewage to sit in tank discharge lines – a main cause of odor permeation and hose failure.
Dometic, OdorSafe, SeaLand, and VacuFlush are registered trademarks of Dometic Corporation.
SaniGard, SaniPump and TankSaver are trademarks of Dometic Corporation.
Plumbing, Electrical Specifications
Plumbing Connection Dimensions
Inlet Fitting Size: 1-1/2 inch 38.1 mm
Outlet Fitting Size: 1-1/2 inch 38.1 mm
Vent Inlet/Outlet Size: 5/8 inch 15.9 mm
†
†
Electrical Requirements 12 VDC
Vacuum Generator: 10 amp
Level Indicator:
Discharge Pump:
3 amp
10 amp
† Requires separate circuit breaker.
24 VDC
5 amp
3 amp
5 amp
6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Front cover
- 2 HTS Benefits
- 3 Installation
- 3 Choosing a Location for the HTS
- 3 Preparing a Mounting Surface
- 3 Avoiding Hose Odor Permeation
- 3 HTS/Vacuum Generator Connections
- 3 Basic HTS Connections
- 4 Plumbing Connections and Hose Layouts
- 4 HTS-Basic Tank Fittings Assembly
- 5 Clamp Connections for Flexible Hose and Fittings
- 5 Solvent Bonding for Rigid Pipe and Fittings
- 5 Vent Line and Filter Installation
- 5 Service Access
- 5 Cleaning
- 5 Winterizing
- 6 HTS Components
- 6 Other HTS Features
- 6 Plumbing, Electrical Specifications
- 7 Plumbing Fittings, Hose and Pipe
- 8 Customer Service
- 8 Warranty