- Vehicles & accessories
- Motor vehicle electronics
- Car media receivers
- Alpine
- TDM-7583R
- Owner's manual
Connections. Alpine TDM-7580R, TDM-7581R, TDM-7581RB, TDM-7580RM, tdm 7583 rb, TDM-7483RB, tdm 7581 rb, tdm 7580 r, TDM-7583R
Add to my manuals
26 Pages
advertisement
Installation and Connections
Connections
(Pink/Black)
AUDIO INTERRUPT IN
(Blue/White) REMOTE TURN-ON
ISO Antenna
Converter Plug
2
3
Antenna
ISO Antenna
Plug
To vehicle phone
To amplifier or equalizer
To power antenna
Ignition Key
(Red) IGNITION
(Black) GND
9
(Blue) POWER ANT
4
5
6
7
(Yellow) BATTERY
!
8
Battery
"
1
$
#
%
A
A
DIN Connector PIN Configuration lgnition
Data Ground
Lch
SIG GND
Power Supply Ground
Shield Ground
Battery
Data Bus
Rch
Speakers
Rear Left
&
(
)
~
+
,
-
.
/
Green
Green/Black
White
White/Black
Gray/Black
Gray
Violet/Black
Violet
Front Left
Front Right
Rear Right
CD Changer
(Sold Separately)
Speakers
Rear Right
Amplifier
(Sold Separately)
Rear Left
:
22
-EN
1 Antenna Receptacle
Connect to the supplied ISO antenna convertor plug.
2
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular phone which provides ground shorting when a call is received.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your amplifier or signal processor.
4 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna, if applicable.
NOTE
This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position.
6 Fuse Holder (15A)
7 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's battery.
8
ISO Power Supply Connector
9 Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.
!
Remote Control Interface Connector
(TDM-7583R only)
To remote control interface box.
"
Rear Output RCA Connectors
RED is right and WHITE is left.
# DIN Connector
Connect this to the DIN connector on the CD
Changer.
$ DIN Extension Cable
NOTE
Older Alpine CD Changer came with standard, straight type DIN connectors. In installations where an L-type connector would simplify installation, the Alpine 4910
02
Adaptor can be used (Sold Separately).
% Power Supply Connector
& ISO Connector (Speaker Output)
( Left Rear (+) Speaker Output Lead (Green)
) Left Rear (–) Speaker Output Lead (Green/
Black)
~
Left Front (+) Speaker Output Lead (White)
+ Left Front (–) Speaker Output Lead (White/
Black)
, Right Front (–) Speaker Output Lead (Grey/
Black)
Right Front (+) Speaker Output Lead (Grey)
.
Right Rear (–) Speaker Output Lead (Violet/
Black)
/ Right Rear (+) Speaker Output Lead (Violet)
: RCA Extension Cable (Sold Separately)
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various Alpine noise suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
23
-EN
24
-EN
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 WARNING
- 4 CAUTION
- 4 PRECAUTIONS
- 6 Detaching the Front Panel
- 6 Attaching the Front Panel
- 6 Initial System Start-Up
- 7 Turning Power On and Off
- 7 (TDM-7583R only)
- 7 Adjusting Source Signal Levels
- 7 (Between Front and Rear Speakers)
- 7 Turning Loudness On/Off
- 8 Manual Tuning
- 8 Automatic Seek Tuning
- 8 Manual Storing of Station Presets
- 9 Automatic Memory of Station Presets
- 9 Tuning to Preset Stations
- 10 RDS Stations
- 10 Recalling Preset RDS Stations
- 11 Turning Emergency Alarm On or Off
- 11 Receiving Traffic Information
- 11 PTY (Programme Type) Tuning
- 11 Tape or Radio
- 12 Priority News
- 12 Receiving RDS Regional (Local) Stations
- 13 Inserting/Ejecting Cassette
- 13 Normal Play and Pause
- 13 (TDM-7583R only)
- 13 Repeat Play
- 13 Blank Skip (B.SKIP)
- 14 Fast Forward and Rewind
- 14 Scanning Programmes
- 14 Manual Reverse
- 14 Programme Sensor (P.S.)
- 15 Controlling CD Changer (Optional)
- 15 Music Sensor (M.S.) Skip
- 15 Fast Forward and Backward
- 16 Repeat Play on Single Track or Entire Disc
- 16 M.I.X. (Random) Play
- 16 Disc Scan
- 17 To Display CD Titles (TDM-7583R only)
- 17 Titling Discs (TDM-7583R only)
- 17 Erasing Disc Title (TDM-7583R only)
- 18 (TDM-7583R only)
- 19 Battery Replacement
- 20 In Case of Difficulty
- 21 Specifications
- 22 WARNING
- 22 CAUTION
- 22 Precautions
- 23 Installation
- 24 Connections