ASSEMBLY. ProForm 400 Gi Treadmill

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrenches and your own phillips screwdriver , rubber mallet , and adjustable wrench .

For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first check to see if it has been pre-assembled. If a part is missing, call toll-free 1-888-533-1333.

1.

Silver Ground

Screw (75)–1

1/2” Screw (48)–10

3/4” Screw (2)–2

Wheel Nut (32)–2

5/16” Star

Washer (97)–2

Make sure that the power cord is unplugged.

1” Tek

Screw (39)–6

2” Bolt (64)–2

3” Bolt (37)–2

4” Bolt (98)–2

1

69

With the help of another person, carefully raise the

Uprights (69) to the vertical position. Insert one of the

Extension Legs (63) into the treadmill as shown. (Note: It may be helpful to tip the Uprights as you insert the

Extension Leg.) Make sure that the Base Pad (61) is under the Extension Leg.

Insert the other Extension Leg (63) in the same way.

6

61

63

2. Identify the Right Handrail (72), which has a large hole in the left side. Feed the Upright Wire (42) into the hole in the bottom of the Right Handrail and out of the large hole in the side. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.

Attach the upper end of the Right Handrail (72) to the right Upright (69) with a 3” Bolt (37). Do not tighten the

Bolt yet. Attach the lower end of the Right Handrail with a 4” Bolt (98) and a 5/16” Star Washer (97). Do not tighten the Bolt yet.

Attach the upper end of the Left Handrail (71) to the left

Upright (69) with a 3” Bolt (37). Do not tighten the Bolt

yet. Attach the lower end of the Left Handrail with a 4”

Bolt (98) and a 5/16” Star Washer (97). Do not tighten

the Bolt yet. Note: There is not a wire harness on the left side.

2

37

3. With the help of another person, carefully lower the

Uprights (69) as shown. Note: It may be helpful to place one foot on one of the Extension Legs (63) as you tip the

Uprights. Make sure that the Extension Legs remain in the Uprights.

Attach each Extension Leg (63) with two 1” Tek Screws

(39) and a Base Pad (57) as shown. Attach the lower

Tek Screw, without the Base Pad, first.

Attach two Base Pads (57) to the base of the Uprights

(69) with two 1” Tek Screws (39).

Attach the two Wheels (66) with two 2” Bolts (64) and two Wheel Nuts (32) as shown. Do not overtighten the

Bolts; the Wheels should be able to spin freely.

With the help of another person, carefully raise the

Uprights (69) to the vertical position.

See step 2. Tighten the two 3” Bolts (37) and 4” Bolts

(98).

3

69

63

64

66

32

57

39

57

39

69

97

69

98

71

37

42

Hole

72

Hole

69

98

97

32

63

66 64

39

57

57

39

7

4. Hold the Console Base (47) near the Left Handrail (71).

Attach the ends of the two ground wires on the Console

Base to the indicated small hole in the Left Handrail with the Silver Ground Screw (75).

4

71

Small

Hole

47

Ground

Wires

75

5.

Touch the Right Handrail (72) to discharge any static.

Press the end of the Upright Wire (42) into the socket in the bottom of the Console Base (47). The connector should

slide easily into the socket and snap into place. If the connector does not slide easily and snap into place, turn the connector and then insert it.

5

72

6. Set the Console Base (47) on the Right Handrail (72) and the Left Handrail (71). Attach the Console Base with four

1/2” Screws (48). Start all four Screws before tightening them; do not overtighten the Screws.

6

72

42

47

47

71

48

48

8

7. Press the Upright Wire (42) into the slot in the underside of the Console Base (47) in the indicated area. Cover the

Upright Wire with the Right Grip Plate (36). Be careful

not to pinch the Upright Wire. Tighten three 1/2”

Screws (48) into the Right Grip Plate and the Console

Base.

Attach the Left Grip Plate (32) over the ground wire and the other wires with three 1/2” Screws (48). Be careful not to pinch any of the wires.

7 47

48

Slot

36

42

32

48

Ground

Wire

8. Attach the Storage Latch (29) and the Latch Spacer (44) to the left Upright (69) with two 3/4” Screws (2) as shown.

Do not overtighten the Screws.

8

69

44

2

29

9.

Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the walking belt (see page 26). To protect the floor or carpet, place a mat under the treadmill.

9