Wall Installation. Uniden EXI7960, EXI916

Color profile: Disabled

Composite Default screen

4) Plug the AC adapter into a standard 120 V AC wall outlet.

Place the power cord so that it does not create a trip hazard or where it could become chafed and create an electrical hazard or fire.

Use only the Uniden AC adapter supplied with this phone and DO NOT use an outlet controlled by a wall switch.

HINT

Before using your phone, fully charge the Nickel-

Cadmium battery pack for

15-20 hours.

5) Raise the antenna to a vertical position.

WALL INSTALLATION

t

Setting the Handset Retainer for Wall Mounting

1) Remove the handset retainer on the base by sliding it upward.

5

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:49 1999

Color profile: Disabled

Composite Default screen

2) Flip the handset retainer over so the tab is facing up.

3) Slide the handset retainer back onto the base.

DO NOT use an outlet controlled by a wall switch.

t

Standard Wall Plate Mounting

This phone can be mounted on any standard telephone wall plate.

1) Plug the AC adapter into the DC input jack on the back of the base, then place the AC adapter cord inside the left molded channel cord holder.

Before you plug the other end of the telephone cord into the modular jack on the wall, charge the battery (refer to

“Charging the Battery Pack,” page 12).

2) Plug a short telephone cord into the

TEL LINE jack on the base, then place the telephone cord inside the right molded channel cord holder.

6

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:50 1999

Color profile: Disabled

Composite Default screen

3) Plug the other end of the cord into the wall jack.

(Remember, the phone must be fully charged before you can use it.)

4) Place the base on the two posts of the wall plate and slide it downward to secure.

5) Plug the AC adapter into a standard

120 V AC wall outlet that is not controlled by a wall switch.

6) Raise the antenna on the base.

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:52 1999

7

Color profile: Disabled

Composite Default screen t

Direct Wall Mounting

If you don’t have a standard wall plate, you can mount your phone directly to the wall. Before mounting your cordless telephone, consider the following:

• Select a location away from electrical cables, pipes, or other items behind the mounting location. Inserting screws into areas such as this can be hazardous.

•

Try to mount your phone within 10 - 15 feet of a working phone jack in order to avoid excessive cord length. Remember, you are not mounting your phone to a wall plate with a built-in phone jack.

• If the selected mounting area has no wooden support beams directly behind it, you will need the appropriate anchoring devices in order for the wall to properly support your phone.

3/16 in.

1) Insert two mounting screws into the wall, with their appropriate anchoring device if necessary,

3-15/16 inches apart. Allow about

3/16 of an inch between the wall and screw heads for mounting the phone.

3 15/16 in.

2) Set the handset retainer.

(Refer to “Setting the Handset Retainer for

Wall Mounting” on page 5.)

3) Plug the AC adapter into the DC input jack on the back of the base and place the cord inside the left molded channel cord holder.

8

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:53 1999

Color profile: Disabled

Composite Default screen

4) Plug one end of the long telephone cord into the TEL LINE jack on the back of the base and place the telephone cord into the right molded channel cord holder.

5) Place the base on the screws and push it downward to secure.

6) Plug the other end of the telephone cord into the wall jack.

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:54 1999

9

Color profile: Disabled

Composite Default screen

7) Plug the AC adapter into a standard

120 V AC wall outlet that is not controlled by a wall switch.

8) Raise the antenna on the base.

10

C:...EXI 7960H1-5 VA.vp

Tue Oct 05 16:59:55 1999