advertisement
![How to Operate the Machine. Clarke ENCORE L2426, ENCORE S2426 | Manualzz How to Operate the Machine. Clarke ENCORE L2426, ENCORE S2426 | Manualzz](http://s1.manualzz.com/store/data/001842175_1-babb86830671967108857e2eec52a245-360x466.png)
How To Prepare the Machine For Operation
How To Remove The Brushes Or Pad Drivers
To remove the brushes or pad drivers from the machine, follow this procedure:
1. Turn the key switch "ON".
2. Raise the brush head by pressing and holding the brush switch until brush head is in its full up position.
3. Turn the key switch "OFF" and remove the key.
4. Go to the front of the machine and unlatch front cover.
Swing cover open and unlatch the brush housings.
5. ("L" Model) Push down on two sides of the brush or pad driver until the gimbals release.
("S" Model) Rotate brush same direction to scrub rotation with a quick snapping action until brush releases.
6. Reinstall right and left brush housing and latch front cover.
DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage.
Do not operate this machine unless it is completely assembled. Inspect the machine carefully before operation.
Figure 18
How To Operate The Machine
How To Operate The Squeegee
The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. Use your hand to lower or raise the squeegee handle. To operate the squeegee, follow this procedure:
1. To lower the squeegee and start the vacuum motor, move the squeegee lever to the right and down. See figure 18.
2. To raise the squeegee, lift the squeegee lever up.
See figure 19.
NOTE: The center position lets the vacuum motor continue to run with the squeegee off the floor to avoid drips and also allows you to back up the machine.
How To Fill The Solution Tank
The solution tank can be filled in the front or through the clear drain hose at the rear of the machine (See figure
20). To fill the solution tank follow this procedure:
1. Add a cleaning chemical to the solution tank. For the correct amount of chemical, follow the directions shown on the container.
2. Fill the solution tank with water. When filling machine in the front with a hose, position hose inside the fill screen as shown in figure 20A.
Page -16-
Figure 19
Figure 20
Figure 20A
CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
C
advertisement
Related manuals
advertisement
Table of contents
- 3 perator Safety Instructions
- 5 Introduction & Machine Specifications
- 8 Symbols Used on Encore S2426 and L
- 10 Machine Control Panel
- 11 Machine Controls and Features
- 12 How to Prepare the Machine for Operation
- 12 How to Install the Batteries
- 13 Battery Maintenance
- 14 How to Charge the Batteries
- 15 How to Adjust Brush Cleaning Path
- 16 How to Operate the Machine
- 16 How to Operate the Squeegee
- 17 Operating the Machine
- 19 Maintenance
- 22 Maintenance for the Squeegee
- 22 How to Adjust the Squeegee
- 23 How to Clean the Solution Line
- 25 Accessories
- 28 How to Correct Problems in the Machine
- 30 Encore S2426/L2426 Final Assembly Drawing
- 31 Parts List
- 33 Parts List
- 33 Parts List
- 33 Parts List
- 33 Parts List
- 33 Parts List
- 33 Parts List
- 44 Frame Axle Assembly Drawing
- 45 Parts List
- 46 Brush Head Assembly Drawing
- 47 Parts List
- 50 Vacuum Motor Drawing and Parts List
- 51 Gearbox Assembly Drawing and Parts List
- 54 Battery Charger Drawing and Parts List
- 54 CLARKE TECHNOLOGY Operator's Manual -Encore S