- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Uninterruptible power supplies (UPSs)
- Eaton
- PULSMXG5000-XL3U
- Installation And User Manual
7.1 Hot Swapping the Power Sub-Module. Eaton PULSMXG5000-XL3U, Pulsar EX RT 5000, MX EXB RT, EXB RT, Transformer 5000, MX 5000 RT
Add to My manuals44 Pages
advertisement
7. Maintenance
7.1 Hot Swapping the Power Sub-Module
This operation must be carried out by qualified electrical personnel only. This operation can be performed without interrupting the equipment.
Disconnecting the power sub-module (87100):
1. Remove the 6 mounting screws to free the main front panel bezel.
2. Place the front panel above the UPS.
3. Remove the 2 mounting screws on each side of the power sub-module.
4. Withdraw the power sub-module.
Note: There is a safety pin at the rear of the module. Lift the sub-module slightly and the sub-module will slide out (follow the arrow in the diagram).
When reconnecting the sub-module, carry out the aboveinstructions in reverse order. A red button will be depressed behind plate 3, reestablishing connection.
Reconnecting the power sub-module:
w Carry out the above instructions in reverse order.
w Replace the faulty power sub-module by another one with same power rating (MX 5000).
7.2 Hot Swapping the Battery Sub-Module
This operation must be carried out by qualified electrical personnel only.
The battery can cause electrocution and high short-circuit currents. The following safety cautions are required before servicing the battery components: w Remove watches, rings, bracelets and all other metal objects from the hands and arms, w Use tools with an insulated handle.
This operation can be performed without interrupting the equipments.
i
This operation must be carried out by qualified electrical personnel only.
Disconnecting the battery sub-module (87101):
1. Remove the 6 mounting screws to free the main front panel bezel.
2. Place the front panel above the UPS.
3. Remove the 4 mounting screws on the sides of the battery sub-module.
4. Withdraw the battery sub-module.
Reconnecting the battery sub-module:
Carry out the above instructions in reverse order.
To ensure safety and high performance, use only batteries supplied by EATON.
i Caution! The battery is heavy
(approx. 60 lbs.).
86-87050-00 A02 - Page 33
86-87050-00 A02 - Page 34
advertisement
Key Features
- 5 kVA 4500 W
- 4 AC outlet(s)
- Sealed Lead Acid (VRLA)
- Rackmount/Tower Grey
Related manuals
advertisement
Table of contents
- 7 Introduction
- 8 Important Safety Instructions
- 9 Symbol Usage
- 11 1.1 Standard Positions
- 12 1.2 Rear Panels
- 13 1.3 Display and Control Panel
- 13 1.4 Accessories for Rack Mount
- 14 1.5 Extended Battery (EXB)
- 15 2.1 Unpacking and Contents Check
- 16 2.2 Internal Batteries Connection (Battery Start-Up)
- 16 2.3 Installation in Tower Position
- 17 2.4 Installation in Rack Position
- 19 2.5 Communication Ports
- 20 2.6 Required Protective Devices and Cable Cross-Sections
- 21 2.7 Hardwire Connection of Output Power Cable to UPS
- 22 2.8 Connection to Output Receptacles
- 22 2.9 Connection of Extended Battery Module, UPS, and Transformer
- 23 3.1 Initial Start-Up
- 23 3.2 Final Start-Up Sequence
- 24 3.3 Operating Modes
- 25 3.4 Operation on Battery Power
- 26 3.5 Return to Normal AC Source
- 26 3.6 UPS Shutdown When AC Present
- 26 3.7 UPS Shutdown When on Battery
- 27 4.1 Display Organization
- 27 4.2 Access to Measurements
- 27 4.3 Access to UPS Set-Up and Maintenance Using the Control Panel
- 28 4.4 UPS Set-Up
- 29 4.5 Maintenance
- 29 4.6 Personalization Using External Software
- 31 5.1 Troubleshooting LEDS (21) and (22)
- 31 5.2 Troubleshooting Not Requiring EATON
- 32 5.3 Troubleshooting Requiring EATON After-Sales Support
- 33 6.1 Description
- 35 7.1 Hot Swapping the Power Sub-Module
- 35 7.2 Hot Swapping the Battery Sub-Module
- 37 8.1 Technical Specifications
- 41 8.2 Glossary