- Home
- Domestic appliances
- Large home appliances
- Water heaters & boilers
- A.O. Smith
- SGE
- Installation manual
advertisement
60
8
Status of the appliance
line four: is empty, or depending on the
heating cycle (9.3 "The appliance's heating cycle") , a text such as HEAT DEMAND.
PROG
12:00 Monday
MO 11:15
PERIOD ACTIVATED
76ÉC
2. The current time falls outside a set time period of the week program.
The figure shows the display with the following information:
line one: the text PROG;
line two: the time, the day and T
1 and T net
alternately (9.3 "The appliance's heating cycle") ;
line three: the next scheduled switch-on time;
line four: displays the text
PERIOD ACTIVATED .
In all modes, the temperature may at any moment drop below the desired temperature. The appliance then enters a heating cycle. This heating cycle is identical
(9.3 "The appliance's heating cycle") for all
basic operating modes.
gis
These errors disappear automatically once the cause of the error has been removed, after which the appliance resumes operation by itself.
The display does not show what type of error has been detected. A comprehensive overview of the errors is provided elsewhere in the manual
.
If, as end-user, you find the appliance in an error condition, you may attempt to restart the appliance by pressing the button
However, if the error returns or occurs several times in a short time you must contact your service and maintenance engineer.
8.4
Service condition
The figure shows the message
!!!
WARNING !!!
MAX. BURNING HOURS:
SERVICE REQUIRED
SERVICE REQUIRED .Should this message appear, then the appliance is in need of a service and maintenance inspection. In that case, contact your service and maintenance engineer.
Note
Setting and if necessary programming of the basic operating modes are described in the main menu
chapter.
Note
The message SERVICE REQUIREDis based on the number of expired burning hours and the preset service interval. Should the service interval have been incorrectly selected, contact the service and maintenance engineer for instructions on how to adjust this. Information on the maintenance frequency is provided elsewhere in the manual
(14 "Maintenance frequency") .
8.3
Error conditions
The figure shows an example of an error condition. If the appliance enters this condition, the display will show the following information:
• line one: error code comprising a letter and two digits, followed by the error description;
• lines two to four: alternately, a brief explanation of the error, and a brief action to resolve the error.
S04: SENSOR ERROR
CHECK
SENSOR OR DUMMY
8.5
Collector temperature warning
This message appears whenever the collector temperature is excessive. This message disappears automatically. If the message does not disappear, you must contact your service and maintenance engineer.
!!!
WARNING
TEMPERATURE
!!!
COLLECTOR
TOO HIGH
Caution
The displayed action to resolve the error may only be performed by a service and maintenance engineer.
There are various types of errors:
• LOCK OUT ERRORS
When the cause has been removed, these errors require a reset with the button before the appliance can resume operation.
• BLOCKING ERRORS
8.6
Q/T Sensor warning
This message appears if the Q/T sensor is incorrectly connected. If the message appears, you must contact your service and maintenance engineer.
!!!
WARNING !!!
Q/T SENSOR NOT
CORRECTLY CONNECTED
Instruction manual SGE
advertisement
Related manuals
advertisement
Table of contents
- 59 Status of the appliance
- 59 Introduction
- 59 Operating modes
- 60 Error conditions
- 60 Service condition
- 60 Collector temperature warning
- 60 Q/T Sensor warning
- 61 Starting and running
- 61 Introduction
- 61 Starting the appliance
- 61 The appliance's heating cycle
- 63 Shutting down
- 63 Introduction
- 63 Shut the appliance down for a brief period ("OFF mode")
- 63 Electrically isolating the appliance
- 63 Shutting the appliance down for a long period
- 65 Main menu
- 65 Introduction
- 65 Notational convention for menu-related instructions
- 65 Switching on the "ON mode
- 65 Setting the water temperature
- 66 Week program
- 66 Starting and stopping the week program
- 66 Changing the appliance's standard week program
- 68 Adding times to a week program
- 69 Deleting times from a week program
- 69 Extra period
- 70 Programming an extra period
- 71 Settings
- 73 Service program
- 73 Introduction
- 73 Setting the hysteresis
- 73 Displaying the error history
- 73 Displaying the appliance history
- 74 Display the selected appliance
- 74 Switching the pump on or off
- 74 Setting the service interval
- 74 Setting legionella prevention
- 75 Solar heating system configuration
- 76 Setting the central heating configuration
- 77 Troubleshooting
- 77 Introduction
- 78 Troubleshooting table for general errors
- 81 Troubleshooting table for displayed errors
- 90 Displayed warnings
- 91 Maintenance frequency
- 91 Introduction
- 91 Determining service interval
- 93 Performing maintenance
- 93 Introduction
- 93 Preparation for maintenance
- 95 Water-side maintenance
- 96 Gas-side maintenance
- 96 Solar collector maintenance
- 96 Finalizing maintenance
- 97 Warranty (certificate)
- 97 General warranty
- 97 Tank warranty
- 97 Collector warranty
- 97 Conditions for Installation and use
- 98 Exclusions
- 98 Scope of the warranty
- 98 Claims
- 98 Obligations of A.O. Smith
- 99 Appendices
- 99 Introduction
- 100 Menu structure
- 102 Electrical diagram for the appliance
- 104 Electrical diagram, solar heating system
- 107 Week program card