Setting up the player. CAMBRIDGE CambridAzur 651BD

azur 651/751BD

Setting up the player

Accessing the Easy Setup Wizard

When the player is turned on for the first time, an Easy Setup Wizard screen will appear. This is a series of guided instructions designed to configure the basic settings for the unit.

Note: If the Easy Setup Wizard has previously been completed or cancelled, it will no longer initiate when you turn on the unit. To access

Easy Setup Wizard again, press the Setup button on the remote control, select Device Setup, then Reset Factory Default. Select " OK " to confirm loading the factory default settings. Once the factory default settings are loaded the Easy Setup Wizard will appear again.

To start the Easy Setup Wizard, please follow these steps:

1. Turn on the TV.

2. Turn on the player.

3. Switch the input selection on your TV so that the TV displays the signal from the player. You should see the first step of the Easy Setup Wizard.

Select the best output resolution

For the latest generation of 1080p, " Full HD " or " True HD " TV displays, the best output resolution will naturally be 1080p. For all other digital televisions this will likely be 720p or 1080i. These are general recommendations that work for most users, but there can be exceptions.

Advanced users may want to try all supported resolutions and choose the one that provides the best visual result.

The 651/751BD supports a special " Source Direct " output resolution on its HDMI output. This resolution is recommended for use with external video processors or high-end TVs with high quality scalers. In " Source

Direct " mode, the player works as a " transport " . It decodes video from the discs and then sends the raw video signal in its native resolution and format, without extra processing, to the external video processor or TV.

The actual output resolution thus varies by content:

Content

PAL DVD

Source Direct Output Resolution

576i

NTSC DVD 480i

Most Blu-ray Movies (film-source) 1080p 23.976Hz or 1080p 24Hz

Most Blu-ray TV shows or Concerts 1080i

(video-source)

SACD and DVD-Audio 1080i

The first step of the Easy Setup Wizard gives you the opportunity to skip the entire wizard. If you are familiar with setting up audio/video equipment and would like to fully customize the player settings using its

Enter setup menu, you may use the ! button to select the continue with the Easy Setup Wizard.

" Cancel " option, then press the Enter button to exit the Easy Setup Wizard.

Use the " # buttons to select the language, then press Enter button to

Depending on your selection of " Primary Video Output " , the available output resolution selections will differ. For the HDMI 1 and HDMI 2 output, the following output resolutions are available:

Choose the primary video output

The player can output video through its HDMI and component output terminals. Composite video output is always available but not recommended. By setting the " Primary Video Output " option, the player can optimize video output of the selected terminal. The choices are

" HDMI 1 " , " HDMI 2 " and " Analog " . If you connect the player to the TV using an HDMI cable, please select " HDMI 1 " or " HDMI 2 " correspondingly. If you connect the player to the TV using component video cables, please select " Analog " .

Auto, 1080p, 1080i, 720p, 480p/576p, 480i/576i, and Source Direct. If

" Auto " is selected, the player will determine its output resolution based on the best signal resolution that the TV can display.

For the Analog (component) output, the following output resolutions are available: 1080p, 1080i, 720p, 480p/576p and 480i/576i.

Note: 1080p only applies to HDMI output, if it is selected for component video outputs, it will automatically be down-scaled to 1080i. Please refer to the specifications of your TV to find the best resolution to use.

Auto

Enter

Note: The best performance will be provided over the HDMI connection.

Between the two HDMI outputs, HDMI 1 should be given priority for use since it benefits from the superior Marvell QDEO video processing solution.

To make your selection, use the " # buttons to highlight the choice, and then press the Enter button to go to the next

Enter

Press the " # buttons to select the desired output resolution, then press the Enter button. The player will apply the selected output resolution and ask you to confirm the selection. If your TV supports the selected resolution, you will see a dialog box with a countdown clock. Use the $ button to highlight the " OK " option and press the Enter button to save the resolution setting. If your TV does not support the selected resolution, you may see a black screen or an error message. In this case please wait for 15 seconds and the Easy Setup screen will reappear. Select a different resolution that your TV can support.

15