advertisement
VRX935VD
Installation and Wire connection manual
■ Contents
1. BEFORE STARTING ............................................................... 63
2. PACKAGE CONTENTS ........................................................... 63
3. GENERAL CAUTIONS ............................................................ 64
4. CAUTIONS ON INSTALLATION .............................................. 64
5. INSTALLING THE MAIN UNIT ................................................. 65
6. REMOVING THE MAIN UNIT .................................................. 67
7. CAUTIONS ON WIRING .......................................................... 67
8. WIRE CONNECTION .............................................................. 68
9. SAMPLE SYSTEMS ................................................................ 71
1.
BEFORE STARTING
1. This set is exclusively for use in cars with a negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “-” terminal before starting. This is to prevent short circuits during installation. (Figure 1)
Car battery
Figure 1
2.
PACKAGE CONTENTS
1 Main unit
2 Tuner Amp unit
3 Manuals
Owner’s manual & Installation manual
Warranty card
4 Power supply lead (For the main unit)
5 Power supply lead (For the tuner amp unit)
6 Connection cord (Main unit ↔ Tuner amp unit)
7 Antenna extension cord
8 Bag for accessories of the main unit (No. 1)
Flat head screw (M5
× 8) ............................ 4
Sems hexagonal bolt (M5
× 8) ..................... 5
Electro tap
Machine screw (M4
× 3) ............................... 4
9 Bag for accessories of the main unit (No. 2)
Hook plate ................................................... 2
Cord clamp
Rubber cap
Special screw
0 Bag for accessories of tuner amp unit
Maunting bracket ......................................... 2
Canoe clip ................................................... 4
Machine screw (M4
× 8) .............................. 4
! Universal mounting bracket
@ Remote control unit
# Battery
(for remote control unit)
$ Outer Escutcheon
% DCP Case
VRX935VD
63
3.
GENERAL CAUTIONS
1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized Clarion service centre.
2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently.
4.
CAUTIONS ON INSTALLATION
1. Prepare all articles necessary for installing the main unit before starting.
2. This model is used with the LCD panel slid forwards (shell loading system). On some types of cars, the LCD panel may touch the dashboard or shift lever, in which case it cannot be installed. Check that the set will not hamper operation of the shift lever before choosing the place of installation.(Figure 2)
Dashboard
5. Use the enclosed screws for installation. Using other screws can cause damage. (Figure
4)
Chassis Chassis
Max. 8 mm (M5 screw)
Figure 4
Damage
6. The source unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles.
T N T
Shift lever
(check that it does not touch the LCD.)
Figure 2
Shift lever
3. Install the unit within 30° of the horizontal plane. (Figure 3)
N T
Figure 5
N
Max. 30˚
Figure 3
4. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand.
64
VRX935VD
5.
INSTALLING THE MAIN UNIT
■ Universal Mount
1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6.
2. Wire as shown in Section 8.
3. Insert the main unit into the universal mounting bracket until it locks.
4. Mount the outer escutcheon so that all the hooks are locked.
Notes:
1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details.
2) Fasten the front stopper securely to prevent the main unit from coming loose.
• Console opening dimensions
182 mm
Hole
Hole
Stoppers
Special Screw
Rear fastening hole (of vehicle)
Instrument panel
Screwdriver
Outer escutcheon
Main unit
2-Spring
Note: Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the main unit.
Stoppers
Figure 6
Rubber cap
Universal mounting bracket
VRX935VD
65
■ Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
This unit is designed for fixed installation in the dashboard.
If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (
∗). (Figure 8)
If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the main unit in the following procedure.
1. Remove the screws from both side of the main unit. Then, at either side, lift the leaf spring until the engaging claws are released from the holes, and slide the spring to the direction of arrow to remove it. Repeat the same for the other side to remove the springs from the both sides. (Figure 7)
2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models.
3. Wire as shown in Section 8.
4. Secure the unit in the dashboard, and then reassemble the dashboard and the centre panel.
2-Screw Engagin claw
Main Unit
2-Spring
Screwdriver
Figure 7
4-Hexagonal screw ∗ (M5 × 8)
Mounting bracket
(1 pair for the left and right sides)
Main Unit
Centre Panel (Note 1)
∗: The screws with this mark are enclosed in this set.
★: The parts and screws with this mark are used to install radio or included in the installation kit.
Figure 8
Note 2
Note 1: In some cases, the centre panel may require some modification (trimming, filling, etc.).
66
VRX935VD
Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool.
6.
REMOVING THE MAIN UNIT
1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw.
2. Remove the outer escutcheon.
3. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, then pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9)
Note: Keep the hook plate. You cannot remove the main unit without disengaging the hook plate.
Universal mounting bracket
2-Hook plate
Instrument panel
Main
Unit
Spring
Outer escutcheon
A
Figure 9
B
7.
CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the wires.
Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires.
3. If the fuse should blow, check to see if the wiring is correct.
If it is, replace the fuse with a new one with the same amperage rating as the original.
4. To replace the fuse, remove the old fuse of the power supply lead and insert the new one. (Figure10)
∗ Power supply lead for the tuner amp unit : 15A
FUSE
∗ Power supply lead for the main unit : 3A FUSE
Note: There are various types of fuse holder. Do not let the battery side touch other metal parts.
CAUTION
After the connection, fix the lead by a clamp or insulation tape for protection.
Fuse holder
Figure 10
Fuse
VRX935VD
67
8.
WIRE CONNECTION
Securely connect to the metal part of the car with a screw, etc.
Black
Choke coil
Yellow
Power supply lead Main unit
Fuse
Main power supply cord
VIDEO output (RCA) ∗5
VISUAL 1 audio input terminal L+R (RCA)
VISUAL 1 video input (RCA)/
DVD changer input (RCA)
TV TUNER input (RCA)
Reset switch
Top view of the tuner amp unit
Connection cord
(provided with this unit)
CeNET cable (Sold separately)
Power supply lead
&
¥
∗2
$ %
∗6
5.1ch Surround Decoder select switch
∗3
Rear audio output (input) terminal L+R (RCA) ∗4
Front audio output (input) terminal L+R (RCA) ∗4
Non Fader output terminal L+R (RCA)
68
VRX935VD
(
Purple/Black
Purple
Green/Black
Blue/White
Green
Brawn
Glay
Grass-green
Glay/Black
Orange/White
White/Black
Red
White
Yellow
0
7
* ∗1
3
)
2
1
8
@
5
9
4
!
6
Black
Blue
#
¡
@
#
$
8
9
0
!
4
5
6
7
No.
1
2
3
(
)
¡
%
¥
&
*
Description
REAR RIGHT+
REAR RIGHT-
FRONT RIGHT+
FRONT RIGHT-
FRONT LEFT+
FRONT LEFT-
REAR LEFT+
REAR LEFT-
+12 V MAIN POWER
Amplifier turn-on lead
ILLUMINATION
+12 V ACCESSORY
GROUND
CCD camera
VISUAL 2 terminal
Radio antenna jack ( ∗2)
CeNET terminal
Phone mute (Brown) ( ∗1)
Spare terminal (Yellow)
Parking brake (Grass-Green)
AUTO ANTENNA
∗1: Connecting the PHONE MUTE Terminal
The lead included with the unit must be connected to the specified position of the vehicle’s connector in order to use the “triggered audio mute for cellular telephones” function.
∗2: Use the attached extension lead when necessary. (Provided with this unit)
Note : Before making any installation, disconnect the car battery - (negative) cable.
∗3: If a 5.1ch Surround Decoder (DVH920, sold separately) is connected and the amp of this unit is used, set the select switch to “LINE IN”. Then the AUDIO OUT (IN) terminal of the Tuner Amp
Unit is only available for audio input, not outputting the audio.
(LINE IN) D N (LINE OUT)
∗4: Connect to a separately sold external amplifier with a separately sold RCA cord (L, R).
Note : When the 5.1ch Surround Decoder is connected, these terminals are only available for audio input.
∗5: Connect to a Rear View Monitor (sold separately) for the rear seat.
∗6: Connect to separately sold VTR equipment with a separately sold connection cord.
VRX935VD
69
■ Connecting the Accessories
• Connection to the external amplifier
The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For detailed information, refer to the instruction manual of the 5.1ch Surround Decoder.
• Connection to the CCD camera for vehicle
The CCD camera for vehicle can be connected to the CCD terminal on the tuner amp unit. For detailed information, refer to the instruction sheet or manual for the CCD camera.
Notes:
• A power supply box (sold separately) is required for connection of the main unit and the CCD camera.
• The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead.
• If the specified lead of the cellular phone is connected to the phone mute lead of the source unit, the audio mute is available when the cellular telephone is used.
• TV Tunner
When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For detailed information, refer to the instruction manual of the TV TUNER.
■ Connecting the parking brake lead
Connect the lead to parking brake lamp earth in the meter panel.
Notes:
• Connecting the parking brake lead to lamp earth allows you to watch TV/VTR/DVD video/video
CD when the parking brake is engaged.
• When the parking brake lead is not connected, the monitor will stay off.
Parking brake lamp
+ lead to battery
- cord parking brake signal lead
Connect these three leads.
Parking brake lead
(bright green)
Parking brake
70
VRX935VD
9.
SAMPLE SYSTEMS
■ Sample System 1
MAIN UNIT
VRX935VD
VISUAL 2 IN
VTR
CCA-389
TUNER AMP
UNIT
RCA Cable
(Visual)
Tuner IN
TTX7501z
TTX7503z/TTX7504z
(CeNET TV TUNER)
CeNET
VISUAL 1 IN
Rear view monitor
RCA Cable
(Visual)
Front Speaker Rear Speaker
CeNET
VCZ625
(DVD CHANGER)
CeNET Mode*
CCA-519-500
*Switch the MODE switch to the CeNET mode.
DCZ625
(CD CHANGER)
VRX935VD
71
■ Sample System 2
MAIN UNIT
VRX935VD
VISUAL 2 IN
VTR
CCA-389
TUNER AMP
UNIT
Rear view monitor
RCA Cable
(Visual)
(Gray) Optical Digital Cable
(included the DVH920)
RCA Cable
(Visual)
Tuner IN
CeNET
VISUAL 1 IN
TTX7501z
TTX7503z/TTX7504z
(CeNET TV TUNER)
(LINE IN)D N(LINE OUT)
Set the select switch to
"(LINE IN)D".
DVH920
(5.1ch Surround
Decoder)
CeNET Mode ∗
(Black)
Front Speaker Rear Speaker
SRK602
(Center Speaker)
SRV303
(Powered Sub
Woofer)
VCZ625
(DVD CHANGER)
CeNET Mode
∗
(Gray)
∗ Switch the MODE switch to the CeNET mode.
72
VRX935VD
■ Sample System 3
MAIN UNIT
VRX935VD
VTR
VISUAL 2 IN
CCA-389
TUNER AMP
UNIT
Rear view monitor
RCA Cable
(Visual)
(LINE IN)D N(LINE OUT)
Set the select switch to
"N(LINE OUT)".
RCA cable
RCA cable
(Gray) Optical Digital Cable
(included the DVH920)
RCA Cable
(Visual)
Tuner IN TTX7501z
TTX7503z/TTX7504z
(CeNET TV TUNER)
CeNET
VISUAL 1 IN
DVH920
(5.1ch Surround
Decoder)
CeNET Mode ∗
(Black)
Amplifier
Front Speaker Rear Speaker
SRK602
(Center Speaker)
SRV303
(Powered Sub
Woofer)
VCZ625
(DVD CHANGER)
CeNET Mode
∗
∗ Switch the MODE switch to the CeNET mode.
(Gray)
VRX935VD
73
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - FEATURES
- - PRECAUTIONS
- 1 CONTROLS
- 2 NOMENCLATURE
- 4 DISPLAY
- 6 WHEN THE DISPLAY IS OPEN
- 10 REMOTE CONTROL
- 14 CAUTIONS ON HANDLING
- 15 10. DVD VIDEO SYSTEM
- 17 11. OPERATIONS
- 17 Basic Operations
- 21 Radio Operations
- 24 DVD Video Player Operations
- 39 VISUAL Operations
- 42 CD/MD Changer Operations
- 46 DVD Changer Operations
- 46 TV Operations
- 49 Other Functions
- 51 5.1ch Surround Decoder Operations
- 55 12. IN CASE OF DIFFICULTY
- 57 13. ERROR DISPLAYS
- 58 14. SPECIFICATIONS
- 59 Installation and wire connection manual